Search Documents

By Lloyd Williams

A vertical air shaft in the Birmingham, Ala., iron district was sunk with a circular cross section and lined with concrete at a relatively low cost to provide needed ventilation for an iron-ore mine. The method of sinking the shaft is described, and the costs are stated in mar-hours with a descriptive list of equipment and a statement on the size and use of temporary buildings. Preparation began May 2, 1955, and the shaft was completed at a depth of [680] feet by September 22, 1956. By October 1956, all temporary building and [aft]-sinking equipment had been removed. The total direct-labor cost for the operation, including preparation and dismantling, was 50,700 man-hours, or 30.2 man-hours per foot. Total rock and dirt removed amounted to 17,523 cubic yards (in place), and the shaft lining required 4,635 cubic yards of concrete to form a circular air shaft with an inside diameter of 16 feet.

Jan 1, 1960

By Berger

A detailed description is given of radio apparatus for controlling a coincidence outfit for relative gravity measurements. This is probably of little interest, since many types of apparatus could be used. The general method employed is the interesting thing about this paper. As long ago as 1883 von Sterneck made a proposal to control two coincidence boxes with the, seine, clock, and many persons have suggested the use of radio for this purpose. In accomplishing this it would appear to the reviewer that this method is probably inferior to that used by the Marland Oil Co., but Berger and Brückner must be given the credit for important advances in the coincidence method. In their apparatus a clock at a central station actuates a relay, which operates a short-wave transmitter (40 m.). At the receiving station the amplification is accomplished at low frequencies... The signal operates a relay which moves a slitted screen in a coincidence apparatus. This screen has been improved considerably, to decrease the mean error in observing a coincidence. As usual, a telescope is used to observe the flashes of light. It has a scale in its focal plane and positions of successive flashes are easily read off and recorded by a second observer. This makes possible' a: higher accuracy in determining the exact instant at which coincidence would have occurred at the zero point on this scale. This method obviously depends on the constance of the mechanical and electrical lag inn both sending and receiving apparatus, and may be adversely criticized from this standpoint. -- A. E. Ruark.

Jan 1, 1929

By John W. Moore

The discovery of porphyries in petroleum by Treibs (17-19) is one of the most significant achievements relating to the origin of petroleum. The presence of these remnants of chlorophyll and hematin in petroleum has immediate practical interest in several aspects of the petroleum industry. Because of their interfacial activities and film-forming tendencies, the metal-porphyrin complexes may be expected to affect the wettability of petroleum-reservoir rock surfaces and influence the flow of fluids in these reservoirs. Also, studies of the relationship of trace elements and porphyrins in petroleum may be expected to yield valuable information on source beds and petroleum migration. Finally, the extreme stability of several metal-porphyrin complexes complicates removal of these metals from some petroleum stocks where they exert deleterious effects on processing and utilization. Metal-porphyrin complexes are commonly associated with the asphaltic residues of crude oils in which they occur (8, 9, 15). However, investigations in this and another laboratory (15) show that small amounts of these complexes often remain in partly refined petroleum products, such as thermally cracked distillates and deasphalted stocks.

Jan 1, 1957

By J. A. Organiscak

The U.S. Bureau of Mines investigated the relationship of bituminous coal seam parameters and the amount of airborne respirable dust generated at longwalls. Dust and coal samples were obtained from 20 longwalls operating in geographically representative coalfields throughout the United States. Statistical analyses of coal seam parameters and airborne respirable dust measurements indicate a likely causal relationship between seam type and respirable dust. Low-ash, high-volatile coal seams were associated with higher airborne respirable dust levels. A negative linear correlation (significant at the 95-pct confidence level) was observed between the seam's ash content and airborne respirable dust, explaining up to 18 pct (R2 = 0.18) of headgate dust level variation and up to 15 pct of tailgate dust level variation. Volatile matter was found to have a positive linear correlation with tailgate dust level, explaining 16 pct of the variation. Further data examination indicates that these relationships with dust are most likely nonlinear, because of improved R2 values over the linear correlations. However, a notable portion of longwall dust production is influenced by other operational parameters, so additional research under more controlled conditions is needed to determine the seam's causative functions.

Jan 1, 2010

By Edwin B. Cook

This report presents the results of calculations of the equilibrium composition of the products of combustion with air of six different mixtures of octane CgH18, plus PbEt4 and halogen-bearing scavengers at three air-fuel ratios, at pressures of 5 and 30 atm., and at temperatures of 350°, 1,000°, 1,800°, and 2,000° K. The air-fuel weight ratio has the values 12, 15:12, and 18. The concentration of PbEt4, M, in milliliters per gallon of iso-octane, has the value 1 or 3. The word "case" is used to designate the halogen concentration. Three cases have been considered [ ]

Jan 1, 1953

By M. K. Quinn, N. P. Reddy, A. W. Khair

"An analysis of coal fragmentation due to the action of a continuous miner is presented. Underground coal cutting by a drum-type continuous miner was simulated in the laboratory using a specially designed unique automated rotary coal cutting simulator (ARCCS). The rotary coal cutter provided the versatility of varying the operating and in-situ parameters to provide information on the effects of generating 37 pm (0.0015 in) particles. In these tests, coal blocks with an approximate dimension of 50.8 x 35.6x 20.32 cm (20x 15x 8 in) were first subjected to confining pressures equivalent to in-situ conditions. The blocks were then cut by the rotary cutting head of the ARCCS, thus simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-situ and operating parameters a number of other parameters such as (1) penetration of bit into coal, (2) penetration resistance (thrust and cutting pressures), (3) rotating velocity of' cutting head, and (4) acoustic emission activity in the coal block were monitored. During the test, all the cut products were collected for size distribution analysis. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted using a sonic technique. At the end of each experiment the cutting paths of the bits in coal were photographed using a camera attached to an optical microscope.The results led to a better understanding of the mechanisms of the fragmentation process during coal cutting and the effect of operating parameters, in-situ conditions and coal type on the size distribution of the cut product:"

Jan 1, 1989

By William H. Pomroy

Fires in underground metal and nonmetal mines pose a threat to the safety of underground miners and to the productive capacity of this Nation's mines. Contaminated air (smoke, carbon monoxide, and other products of combustion) is the primary life safety hazard created by a mine fire. The most reliable defense against the hazard posed by the rapid spread of contaminated air underground is early warning fire detection and rapid evacuation. This Bureau of Mines report describes the design and operation of four prototype early warning fire detection systems, for underground noncoal mines, presently undergoing prolonged in-mine testing by the Bureau. The systems are described within the context of the underground mine environment.

Jan 1, 1985

By Robert T. MacMillan

An essentially chemical technique has been developed on a small scale for the efficient utilization of certain domestic titaniferous iron ores. Three main steps are involved: (1) Sintering the ore at 1,050° C. with carbon and soda ash to reduce the iron to metal powder, retaining the titania in the slag, (2) separating the powdered iron from the slag, after wet grinding, by magnetic or gravity methods, and (3) sulfuric-acid decomposition of the titania fraction to produce pigment and certain byproducts. The technique was first applied to the tailings from the Bureau of Mines bauxite-concentrating plant at Bauxite, Ark. A good grade of powdered iron was produced from this material. Subsequently, the work was diverted to the study of the titaniferous magnetite from the MacIntyre Mine at Tahawus, N.Y., because of the potentially higher recoveries of iron, titanium and vanadium. Ninety percent of the iron in this ore has been recovered as an iron powder analyzing 90 percent metallic iron and containing 2 to 3 percent TiO2. The remaining titania was found in the slag and was recovered as pigment-grade TiO2 by application of a suitable technique. The vanadium was distributed between the TiO2 fraction and the alkaline liquor resulting from the wet-grinding and magnetic-separation operations, with only a minor proportion retained by the metallic iron.

Jan 1, 1950

By Thomas Varley

"The literature on flotation of oxidized ores except for patents (especially for reagents) is very sparse. The Bureau of Mines in 1936, published a circular on the subject, by Ralston and Allen. The treatment of oxides by flotation was then in its infancy, but several of the most important mining companies in the Western United States and Mexico are now operating flotation plants for treating oxidized ores. The purpose of this present circular is to review the progress made and bring the subject up to date. One of the writers of the 1916 report (Mr. Allen) has been associated with some of the most important mining companies who have put into practical operation the process of flotation of oxidized ores; among these companies are the Shhttuck Arizona Copper Co., Bisbee, Arizona (now the Shattuck Denn Co.) and the San Francisco Mines of Mexico, Ltd., San Francisco Del Oro, Chihuahua, Mexico. His experience and other sources of information have been freely drawn on in pre-paring this paper. Mr. Ralston, assistant chief metallurgist of the Bureau of Mines, contributed many valuable suggestions and criticisms.Sulphidizing Reagents for Oxidize Ores.The various reagents and methods that might possibly be used for sulphidizing were summarized by Ralston and Allen as follows:""Sulphidizing (1) by the use of hydrogen sulphide on either the dry or the wet crushed ore, (2) by the use of solutions of the various sulphides and sulpho-compounds of sodium, (3) by the use of solutions of the various sulphides and sulpho-compounds of calcium, (4) by the use of sulphur vapor, (5) by the use of a sulphureted oil, (6) with colloidal sulphur."

Jun 1, 1927

Geological discontinues in the coalbed, such as faults, sandstone channels, permeability facies, lithotype changes, and large scale partings in the coal seam, can cause intermittent production problems or produce unexpected amounts of water or gas from degasification boreholes. These discontinuities not only can impact methane emissions into the mine workings, especially if they hinder proper and effective degasification of the coalbed but may act as conduits for methane flow from gassy strata into advancing mine workings. The effects of these discontinuities are still under debate by mining and gas production experts. This study presents a numerical investigation using reservoir simulations of the effects of partings and permeability facies and lithotype changes on the production performances of vertical and horizontal degasification boreholes, as well as the emissions during longwall operations. In this work, the grid block was designed in a multi-layer 3-D structure which enabled spatial descriptions of the geometries and properties of the discontinuities within the coal seam. The studied coal seam discontinuities and their properties were distributed arbitrarily within the model. Production was simulated by vertical and horizontal boreholes. Degasification boreholes operated two years prior to start of the mining. The results of this numerical study show that in coal seams with major heterogeneities and discontinuties, the geometry and location of the boreholes are important for improved gas production. These considerations are also important for controlling methane and water inflow into the working environment during longwall mining.

Jan 1, 2008

By C. A. Herbert

The old fatalistic idea that industrial accidents were a necessary part of industry and that little, if anything, could be done about them has been succeeded by realization that a majority of the hazards causing these accidents were man-made and that if they could be recognized most of them could be eliminated and the accidents prevented. Recognition of these facts has brought about substantial reduction of accidents in many coal dines, as well as in other industries. Knowledge of the hazards and their elimination has been obtained largely through a study of individual accidents and the causes which led up to them. With this thought in mind tae available data on coal-mine explosions in Illinois were studied.

Jan 1, 1934

By E. J. Gleim

Contact with trolley wire in the mines of the United States has taken a considerable toll of life throughout the years that trolley locomotives have been employed as a means of' transportation. A study3/ of the records over a 15-year period for one State alone showed that, of 98 fatalities resulting from contacts with electrical circuits and equipment, 75 were caused by direct or indirect contact with unguarded trolley wire in coal mines. The law relating to guarding trolley wires in the mines of this particular State, as amended in 1935, reads in part as follows: "All trolley wires carrying 220 volts or more, and less than six feet six inches above top of rail, must be guarded at all points under which men and animals are required to pass***,'" The natural conclusion to be drawn from such records is that lack' of guards or shields must be held responsible for these fatalities. As a preventive measure, it has been advocated that every foot of trolley wire in mines should be guarded. Although some such drastic steps may appear to be amply justified, closer examination of the records nor this and other coal-mining States shows that absence of guards is not entirely responsible; but rather that other factors, such as carelessness and neglect it the observance of certain well-established simple rules concerning installation and location of trolley wires, also are responsible. In other words, if trolley wire is installed carelessly and its maintenance is neglected, it should not be expected that the mere installation of guards will overcome such carelessness and neglect. This publication discusses Various types of guards that have been used in Coal and metal mines of this country, together with related steps bearing upon the problem of 'preventing shock and fatalities from contacts with trolley wire. The material herein contained is taken largely from Information Circular 6577,4/ now out of print, and has been revised to include some types of guards that have been used in metal mines, together with a discussion of guard materials not covered in that publication.

Jan 1, 1945

By Robert C. Ellman

The Bureau of Mines investigated the factors that cause agglomeration of lignite by freezing during winter shipment and sought methods to avoid it. Tests showed that lignite may be freezeproofed by removal of the relatively small quantity of moisture involved in forming the frost crystals which cement particles together, or by controlling the crystal characteristics. Adding dried lignite fines proved to be an effective and superior freezeproofing method. Commercial adoption of this method has been successful.

Jan 1, 1965

By J. M. Mutmansky, C. Lee

"This paper outlines some of the work associated with a research study into the relationship between the characteristics of coal mine dust and the incidence of coal workers' pneumoconiosis (CWP). The project involves study of the chemical, mineralogical, and morphological characteristics of the dust. Early stages of the study have dealt primarily with the size analysis and elemental composition of airborne dust in continuous miner sections. This paper outlines the procedures and findings of the elemental analysis portion of the study.Most of the previous elemental analyses of coal were made available in the quest for information on the combustibility of coal dust or on causal agents and prevalence of CWP. However, no extensive studies have been performed to date, primarily due to the limitations of the analytical methods. A review of the analytical methods for elemental characterization of coal and coal dust particles is presented. TI1e comparisons are made based on the sample mass required, the sample preparation required, the destructivity of the test, and the capability of providing an easy multi-element analysis. The reasons for selecting the proton-induced x-ray emission spectroscopy (PIXE) method are outlined.The PIXE method was applied to both the airborne coal mine dust and channel samples collected from seven continuous miner sections in six different mines. Channel samples of the coal, roof and floor were collected and analyzed. Airborne dust sampling was performed using multi-stage cascade impactors and permissible 2.0 I/min pumps. Sampler locations were fixed in the sections with respect to the continuous miner and roof bolter or with respect to the intake and return airways. Sampling times varied from 45 minutes to 6 hours, depending on the dust concentration.The statistical analysis of the resulting elemental data is presented. Of particular importance are the analyses of the variation of elemental composition with size and the variation in elemental composition over the working section. One interesting finding is outlined showing the multivariate statistical analysis of the trace elements and its implications in the identification of the dust sources. The paper concludes with an analysis of the ramifications of the elemental data to related medical studies."

Mar 1, 1989

By John Nagy

A study was made in the Bureau of Mines experimental coal mine of factors affecting gas ignition by a cutoff explosive charge. Experiments showed that, although gas could be ignited under some circumstances, the probability under normal mining conditions would be low. The use of permissible explosives, relatively short-delay intervals in firing adjacent holes, blasting to a 6-inch kerf, and reasonable care in the placement of the holes favor safe blasting and are current practice in mining. The experiments also showed that the weight of the charge is not a primary factor in the ignition of gas by a cutoff charge. The quenching action of a first charge on the igniting action of a second was verified in a supplementary study. Related experiments have shown that gas at the face may be ignited by a single charge of explosive when fired with a light coal burden. Permissible explosives were less hazardous under these conditions than nonpermissible explosives. The frequency of gas ignition in cutoff and single-charge experiments increased as the linear distance between the sheared face and the opposing mine rib increased.

Jan 1, 1960

By F. S. Boericke

"INTRODUCTION The mineral found in natural-chromite deposits is never pure Fe0.Cr203, but rather one in which the Fe0 and Cr203 are in part replaced by Mg0 and A1203, respectively. The purest gravity concentrates from many domestic de¬posits consist of a mineral referred to as ""picotite,"" in which this isomorphous replacement is such that the ratio of chromium to iron is low. The Bureau of Nines has investigated methods of chemically beneficiating ores that contain too much iron to be classed as ""high-grade"" chromite 3/ Early investigations 4/ demonstrated that high-iron chromite or picotite ores can be roasted with carbon to obtain selective reduction of the contained iron, and that most of this reduced iron can be removed by acid-leaching the roast products to produce residues of higher chromium-to-iron ratios. tests 5/ indicated that commercially acceptable reaction rates cannot be obtained at roasting temperatures below 1,3000 C., using solid carbon as reducing agent. By this high-temperature reduction and subse¬quent acid-leaching, however, all ores investigated, regardless of the original composition, readily yielded residues considerably better than the minimum specifications for high-grade chromite.In an effort to obtain satisfactory reduction of chromite at lower temperatures, liquid and gaseous seducing agents were tested with varying success. Of the several reducing agents used, methane appeared to be the most promising and was shown to be highly effective at temperatures between 1,000º and 1,100º C., roughly 300º below the roasting temperatures necessary in solid carbon reduction. Further experiments indicated that mixtures of methate with some diluent (hydrogen or other nonoxidizing gas) gave better reduction than did methane alone."

Feb 1, 1946

By Thomas M. Barczak

This US. Bureau of Mines report examines the roof and floor contact pressure provided by the interaction of a shield with the surrounding strata. Controlled forces were applied to an 800-ton two-leg shield in the Bureau's mine roof simulator; the distribution of forces acting on the canopy and base of the shield were measured with 24 hydraulic pressure cells. Several influential factors that affect the load distribution were investigated: (1) the magnitude of loading (leg pressure); (2) the profile of the canopy, principally the upward-sloping tip; (3) the base-lifting device; (4) horizontal load acting on the shield; and (5) compliancy of the immediate roof and floor. It was concluded that the shield does not develop full canopy or base contact without deformation of the strata. Maximum contact pressures are developed at the rear of the canopy and on the toes of the base. Less than 10 pct of the available shield capacity is developed at the canopy tip despite the design intention to ensure tip contact. Horizontal loading reduced the toe pressure acting on the base by as much as 75 pct. The base-lifting device exaggerated the inherently high toe loading, increasing the contact pressure by more than 200 pct.

Jan 1, 2010

By R. J. Leary

The natural gas-air burner described in this report was designed and constructed to meet the thermal requirements of a convective process for heating steel scrap. This process involved downward combustion of natural gas with air, blending the combustion products with diluent air, and then passing this tempered stream of gases downward through a porous bed of steel scrap contained in the furnace chamber. The scrap would be heated to a temperature limited by the adiabatic flame temperature of the gas stream in a period that depended on the rate at which heat was supplied per unit of bed cross section. The temperature of the gas stream would be limited to that beyond which an objectionable degree of oxidation would occur; for carbon steel this limit had been found to vary from 1,900° to 2,100° F. with the superficial velocity of the gas stream. The productivity of the process was dependent on the rate of heat input per unit of furnace cross section; for the 3-foot-diameter experimental furnace an input of 680,000 B.t.u. per hour was desired. The burner described was designed to meet these conditions of temperature and heat input. It provided for three streams of entering gases: (1) A primary air-fuel mixture too rich to be combustible, that is, above the upper flammable limit; (2) secondary air for combustion of the primary mixture; and (3) tertiary air, principally for cooling the combustion products to the temperatures desired for process operation. Downward combustion of the primary and secondary streams occurred in a flame stabilized on an annular port, while tertiary air flowed in an annular path surrounding the port and also through an axial channel whose wall formed the inner ring of the annular port. This burner performed beyond the designed heat-input rates while producing stable flames, which were adjusted readily to the temperatures desired. Gas-stream temperatures were easily controlled to within 15° F. of the desired value by simple manual adjustment of the flow valves.

Jan 1, 1959

By Jack L. Henry

The ternary system A14C3-AIN-Al203 has been examined to determine compositions which may display desirable high-temperature refractory properties. Powder methods were employed in the synthesis of all test compositions. Forming and sintering behavior was examined and hot-pressing parameters were measured. Several properties were studied for each composition of interest in the system. The properties included hydrolysis rate in moist air, elevated temperature oxidation rate, density, softening point, tensile strength, and rupture strength. In most cases equilibrium was not achieved, and the data are representative of a nonequilibrium system. Approximately 16 separate phases have been observed in the system. Forming behavior and selected properties of five compositions of interest were compared with those of aluminum oxide and aluminum nitride. None of the compositions compared favorably. Oxidation and vaporization appear to be serious drawbacks to the use of these compositions at elevated temperatures.

Jan 1, 1969

By R. M. Santmyers

Caesium, rubidium, and lithium are sometimes described as the minor or rarer alkali metals. They generally occur together in nature, although, lithium is distributed more widely and is far more abundant than either of the other two. The chemical, and even the physical, properties of these three elements can best be considered In conjunction with the more familiar members of the alkali group, sodium and potassium. The five elements lithium, sodium, potassium, rubidium, and caesium show an interesting gradation properties from member to member with the increase in atomic weights. All are silvery white and soft enough to be cut with a knife. They tarnish rapidly in air and decompose water at ordinary temperatures. The lowest temperature at which the action of the several metals on water can be de¬tected is -98°C. for sodium, -105°C, for potassium, 108°C. for rubidium, and -116°C. for caesium. The chemical activity appears to increase steadily from

Jan 1, 1930