Search Documents

By Huang Daguang, Paulo Couceiro, Juan Navarro

Mining is typically conducted through a set of interdependent unit-operations, which commonly include drilling, blasting, digging and hauling, in order to deliver the required ore material into the comminution circuit and to remove waste rock with minimum impact in the operation. In such complex environment, the identification of critical paths, and respective interfaces between different unit-operations, are necessary to determine a sustainable long-term operational program. Facing this challenge, adaptive cost optimization strategies are required to increase productivity and revenue while minimizing potential environmental impacts. Since the overall mining efficiency can be strongly impacted by blasting outcomes, an operating method based on the searching of the ideal blast design is required in order to minimize the mine total cost of ownership. The implementation of a consistent continuous improvement program requires specific care in terms of design, control and execution of the different stages of blasting. For that, the application of the most advanced technologies for rock characterization, based on drill monitoring systems, and smart explosive products, allows the improvement and control of blast results by adapting the explosive energy distribution to the rock condition, so as to optimize the performance of downstream stages such as digging, hauling and comminution. This paper describes the application of a heuristic optimization approach, where blast parameters are used as decision variables to evaluate the potential impact of several blasting scenarios on subsequent unit operations, under the continuous ability of modelling, measuring and calibrating operational performances along of the mine cycle.

Feb 6, 2023

By Tapan Goswami, Lloyd Hain, Geoff Brent

For many years Ramp 24 at Ensham mine in Queensland, Australia has suffered substantial coal loss and damage due to the fragile nature of the coal and problematic geological conditions, which have proved very challenging. In the past various blasting techniques were applied in attempts to improve coal recovery. One approach was to use a shallow throw (cast) blast followed by a separate post-strip blast underneath. Another method was the introduction of the practice known as “baby decking” with the addition of a large buffer of material in front of the coal. However, despite increasing mining costs, none of these techniques adequately reduced coal edge loss and damage.

Jan 1, 2008

By Richard Givens, Thomas Baginski

Technological advancements in warhead designs and implementations have driven the development of arrayed initiation networks of highly accurate, highly reliable, and extremely safe detonators. Recent development efforts have produced advanced Exploding Foil Initiator (EFI) based systems that have been adapted for civilian use in commercial blasting applications.1,2,3,4,5 This novel, high technology system promises multiple improvements and advantages over the manufacturing, transportation, tracking, storage, inventory and field operation of current detonator systems. Ultimately the insertion of this technology would result in fielding a Non-Energetics Based Detonator (NEBD). Insertion of complementary technologies into the detonator’s supporting systems would greatly advance current detonator hardware/software.

Jan 1, 2011

By Robert L. Martin, Brian W. Stump

"The Black Thunder Mine is located in the Powder River Basin of Northeastern Wyoming. Over 39.2million tons of coal were produced at the Black Thunder Mine in 1996. Just over 100 million pounds ofANFO/Emulsion blend were consumed in that same year. Currently around 30% of the overburden is cast to final with the use of explosives. With plans for a mine expansion, explosives will continue to play a very vital roll well into the future."

Jan 1, 1997

By R. Alford

In the modern world of demolition safety is paramount and unnecessary or unquantifiable risks are not accepted (FasterCapital, 2024) and all risks must be kept As Low As Reasonably Practicable (ALARP) (BSI, 2017). This principle has led to a huge reduction in deaths in the last 50 years and the statistics continue to improve although this is starting to plateau (Beal, 2007). Under normal circumstances, this is now simply part of the normal way work is done and systems are in place to ensure both safety and economic profits are assured. What happens when the environment is less controlled and risks are unknown, such as after a natural disaster, war, an accident or a stand-up from a failed demolition attempt? A dangerous structure cannot responsibly be left alone with a fence around it so some action must be taken, but how can this be done safely and responsibly? An incident in Didcot, England in which half of a power station’s boiler house being prepared for an explosive demolition collapsed suddenly, killing four men in 2016 provides a useful case study of how technology, creativity and planning can be used to conduct complex demolition fully remotely to avoid any further risk to life.

Jan 21, 2025

By William Hissem

The topics in the title line of this article are desirable and applicable to entire industries that exist outside the realm of the ISEE’s readership. But the issues I will discuss herein are specific to those who drill, blast, and excavate rock as part of their business. Civil and site construction projects, mines, and quarries specifically comprise the group who will benefit from this discussion.

Jan 1, 2014

By Norman Paley, Zachary Pickett

The Red Dog Mine is a high-grade zinc-lead mine located in northwest Alaska which began operations in November 1989. In June 2014 the upper half of a charge in a trim shot in the Aqqaluk pit deflagrated. No other holes in the area were observed to react and the remainder of the pattern was shot without incident. This was the only known case of a deflagration in the 25 years of operations. As part of the investigation into the cause of this incident rock samples were obtained from the area of this hole and from other areas in this pit.

Feb 1, 2020

By Walter Valery, Sarma Kanchibotla

Due to the global financial crisis, the world economy has turned upside down and most major economies in the world are facing severe recession for the past one and half year. During this period most commodity prices have tumbled by more than half from their peaks and such a sudden and severe economic downturn is not seen since the great depression. This sudden drop in commodity prices and lack of credit made many mining operations unviable and even those mines that are marginally viable at this point are operating under severe cost pressures and capital expenditure restrictions.

Jan 1, 2010

By Lon Santis, Michael Swisdak, David Leidel, John Tatom

The Institute of Makers of Explosives (IME) and A-P-T Research, Inc (APT) have developed and released a quantitative risk management tool, IMESAFR (IME Safety Analysis For Risk), for the commercial explosives industry. Consequence algorithms in IMESAFR are considered state-of-the-art. Generally, they mirror those in SAFER (US Department of Defense Explosives Safety Board quantitative risk management software). The science behind the software has now been assessed for its maturity. Results have identified areas where additional test consequence data could improve predictions. To address these areas, full-scale testing programs to provide the needed data have been formulated. Proposed testing efforts include work to: (1) improve characterization of explosive articles now absent from SAFER, and (2) refine modeling of the Potential Explosion Site (PES) types, particularly small metal structures, also not found in SAFER. Goals of each program as well as requirements for conducting the tests have been established. Testing results are to be used to improve the algorithms and to further the state-of-the-art in risk-based explosives safety.

Jan 1, 2012

By P. Couceiro, J. Navarro

A new methodology to perform selective blast designs by adapting the explosive energy, hole by hole (or in the hole), to the rock properties as a combination of their strength properties through the X-Rock model has been developed based on drill-monitoring data from both autonomous and manual rotary drilling modes. For that, a thorough normalization process has been developed to minimize external influences in the data induced by the different rig system and the operator interventions during manual drilling operation. Principal component analysis has been used to combine drill monitoring information. Data from 48,385 blastholes, comprised in 102 production blasts at 7 different levels in one expansion of the mine have been used for the analysis. The methodology, called X-Energy, combines the X-Rock model outputs with actual blast design parameters (drill pattern, stemming and borehole length, explosive mass/density and others) and a constant variable obtained from a machine learning algorithm, to estimate size distribution and percentage of fines and coarse material, hole by hole, by combining and recalibrating the Kuznetsov (Cunningham, 1987) based equation. From it, a new shovel-independent diggability model has been developed as combination of the P80 size, the rock properties (from the X-Rock) and a constant variable obtained from a machine learning algorithm. The X-Energy application presented in this study have been implemented in Minera Escondida Limitada (MEL), to design and operate production blasts with the goal of varying the explosive density to the rock properties to obtain a more uniform size distribution and digging rates, hole by hole, based on a target size and rate, and improving slope care, preventing active faults to fail. The methodology has been applied and validated in 17 production blast (8,277 blasthole), unlocking an average of 12.8% reduction in explosives costs (explosive consumption), by combining a pattern expansion strategy and a better distribution of the explosive density within the blast. The results demonstrate how a better distribution of the explosive energy by varying its density in the hole according to the rock and blast geometry variables can reduce powder factor (explosive consumption) while improving or maintaining blasting and digging results.

Jan 1, 2024

By Ajoy Singh

A study was conducted to investigate the damage potential to underground multi-seam openings caused due to vibration generated by open-pit coal mine blasting. The objective was to recommend optimal explosives weight per delay to be detonated in open-pit blasts to ensure the safety and stability of underground openings. Sixteen blasts with varying charge weights and initiation sequences were conducted at Samleshawari open-pit mine and eighty four blast vibration data were recorded in the Hingir Rampur underground colliery in India. Analysis of vibration data showed that roof of the underground openings vibrated with higher amplitude of vibration compared to pillars and floors. The amplifications of vibration in the roof at the junction were upto 4.3 times the pillar vibration. It was observed that coal chips detached from roof when the peak particle velocity reached 131 mm/s or high. The vibration magnitude recorded was higher in upper seams openings than in below seam openings. Rapid attenuation of vibration was recorded in below-seam openings at similar locations. Appropriate particle-charge weight-distance equations were established to calculate the safe explosive weight per delay to be detonated in open-pit mine for safety of multi-seams workings of underground mine. The support for the galleries and junctions were further modified for the working seams to ensure greater safety.erground Coal Mine

Jan 1, 2012

By K Taylor

Small scale tests have been conducted in blasting vessels in the laboratory, where the effects of explosive composition, charge diameter, explosive confinement as well as additives to the explosive were examined on NO, NO2, CO and CO2 production. Fumes were analyzed continuously using a flue analyzer, providing analysis every 15 seconds. The results were compared to previous work conducted in the laboratory and to literature findings. It was found that the type of the explosive was the most dominant factor with emulsion explosives producing significantly less amounts of toxic gases. ANFO was shown to always produce nitrogen oxides, even when fuel rich. Tests were also conducted by detonating explosives in broken rock, simulating the release of products of detonation during the formation of a muckpile. Products of detonation were affected by the presence of atmospheric air or rock around the charge. Gaseous products of detonation migrated through the rock piles at different rates, resulting in a change of toxicity values over time. In the small scale experiments, CO appeared to travel faster than CO2 while NOX was not identified. Analysis of the gases that were released during digging, several hours after the blast, resulted in high temporary concentrations of toxic fumes.

Jan 1, 2014

By Baohua Guo, Xuelin Yang, Tingkan Lu, Hailin Sun

The work presented in this paper mainly involves two parts. Firstly, the fundamental characteristics of the high pressure carbon dioxide gas fracturing technique (CO2 technique), including, a proposed method of TNT equivalence calculation, which is used to calculate the TNT equivalence of discharge of CO2 technique, and the comparison of the explosion volume generated by dynamite and expansion volume of liquid carbon dioxide is conducted to show the differences of fragmentation capacity between the two of them. Secondly, the coal seam fragmentation mechanisms of CO2 technique are proposed, including, 1) Gas jet cutting and penetration by shaped charge, 2) Gas volume expansion by changing phases of carbon dioxide, 3) Coal seam softening by destress blasting and 4) Coal seam fragmentation by discharge vibration, associating with the mechanisms, the equations for calculating fragmentation radius are developed and verified.

Jan 1, 2017

By Stephen G. Rieben

Almost everyone has at least heard of the two one-call systems which serve New England. They are "Call Before You Dig", which covers Connecticut, and "Dig Safe", which covers the remaining five New England states. Those of you who are more familiar with these programs know that it is our job to help guard against the accidental dig-ups of buried plant and to prevent facility service disruptions. We cover all types of buried facilities, from cable television to high pressure gas transmissions lines, telephone cables, electric facilities, fiber optics and everything in between

Jan 1, 1990

Laboratory experiments show that the delay detonators, either electric (copper coated or aluminium) or non-electric (down-the-hole) as generally used in opencast mines and quarries have some scattering from the actual firing time due to manufacturing inaccuracy and variations in basic ingredients of the product. This scattering varies from 1 to 4 % depending on the product quality. Due to this component scatter, adverse blasting effects like misfires, overbreak, underbreak or fly-rock may occur if the design patterns are not judiciously made. It has also direct impact on muck profile and fragmentation.

Jan 1, 1999

By Agne Rustan

This paper is intended to give a summary of the first ten Symposia on Rock Fragmentation by Blasting where the symposia activities were governed by a Steering Committee replaced at Fragblast 2 by an International Organizing Committee (IOC). At Fragblast 9 the name was changed to Fragblast International Organizing Committee (FIOC). Eighty four pages of statistical data about Fragblast 1-10 is documented on the Fragblast Website (ISEE.org).

Jan 1, 2014

By R W. Thomas

"This paper explores the possibilities of generating radical improvements in the drihing costs andproductivity of blastholes through the efforts of integrated teams as opposed to traditionalcustomer/vendor relationships."

Jan 1, 1996

By Peter Moser, Mark Ganster, Andreas Gaich

Surveying of a bench face before blasting is a pre-requisite for a proper blast planning and for a satisfying blasting result both in terms of safety and fragmentation. When surveying a bench face, preferably a large amount of measurement points are required in order to determine the geometry and especially the irregularities with sufficient accuracy. Only contact-free measuring systems allow evenly distributed measurements over the whole bench surface. Existing systems such as total station, laser profiler, or laser scanner show significant drawbacks such as that surveying results are just isolated values of the bench geometry such as heights or profiles, that borehole positions have to be defined in advance in order to know where to take profile measurements and that systems require special surveying skills and that they are expensive too. In order to overcome these difficulties and to provide the blasters a simple tool for bench surveying, blast design and layout and the subsequent back-transfer of the blast plan into the quarry, the Department of Mineral Resources& Petroleum Engineering of the University of Leoben, 3G Software & Measurement company and Mineral AB, one of the largest producers of aggregates in Europe formed a joint venture to develop a new system. Based on an existing stereophotogrammetric system for rock surface surveying and joint analysis (JointMetrix), a new tool was developed within a year. Apart from several mines and quarries using that new tool already today in the daily work, both the Department of Mineral Resources& Petroleum Engineering at the University of Leoben and Austin Powder GmbH Blasting Service did a lot of studies to determine the reliability of the new stereophotogrammetric blast surveying and planning system and its precision in comparison to classical laser surveying equipment. After 1 year of testing and comparison with laser based surveying instruments, it can be concluded, that the new technology of blast surveying& design systems based on stereophotogrammetry is suitable for being used in the daily work routine in quarries and mines. The comparison of the precision of laser based systems and stereophotogrammetric systems has shown, that the deviation between these two types of systems is less than 10 cm, in many cases even lower.

Jan 1, 2007

By Bruce B. Redpath, Doug Crice, Rob Huggins

Over the last decade, instrumentation has been developed that allows the application of seismic reflection methods to groundwater and engineering problems. At the Geological Survey of Canada, we have been developing and testing shallow reflection techniques for mapping the bedrock topography and structure within the overburden. We have attempted to develop methods which can be implemented with a minimum investment in equipment and computing capabilities. The data are recorded on a l&channel engineering seismograph, using a single high-frequency geophone per channel, and a hammer or in-hole shotgun (“Buffalo gun”) as the seismic source. Processing and display of the data can be accomplished on an Apple II+ or IIe microcomputer and an Epson wide-track dot-matrix printer.

Jan 1, 1991

By Gary Cavanough, Stuart Addinell, Hector Parra

Drilling deep, straight, accurate holes in hard rock to achieve efficient blasting is a challenge for the mining/quarrying industries with short holes normally drilled using “top hole hammer” (THH) and deep holes using “down the hole Hammer” (DTH).

Jan 1, 2013