Search Documents

By S. Deonarain, L. S. Schultz

"This paper details the process and methodology followed to rehabilitate a rectangular ventilation shaft, situated in the Free State region of the Witwatersrand Gold Fields in South Africa. The shaft consists of seven compartments where self-mining of the sidewalls had taken place and damage to the decayed steel work in the shaft had taken place, thus limiting access down the shaft. The paper will provide some insight into the successes and challenges encountered during the project and may provide some learnings for future projects of a similar nature. INTRODUCTION The ventilation shaft forms part of the Phakisa Mine, situated in the Welkom area of the Free State province of South Africa, and is located in the Southern part of the Witwatersrand Basin, one of the world’s largest known and richest gold deposits (Figure 1).As is typical in South African gold mines situated in the Witwatersrand basin, the shaft is 1 770 metres deep (below collar). The shaft was sunk during the early 1940’s and comprised a rectangular shape with 7 compartments, used for both rock hoisting and men and material winding, respectively, with a single lift “Mary-Anne” compartment. Early in 2003, the mine decided to change the shaft from a downcast hoisting shaft to an up-cast ventilation shaft. The conveyances, ropes, winders and headgear (head frame) were removed and replaced with a high volume fan delivering 323m³/s of air at a pressure of 4.2Pa on surface. The up-cast velocity in the shaft was 6.5m/s, however this reduced significantly with the scaling of the shaft and the restrictions at shaft bottom. Although Harmony had converted the shaft from a downcast service shaft to an up-cast ventilation shaft some years back, the shaft steel work in the barrel of the shaft was left intact. Over the years, the steelwork in the shaft had decayed (rust and grime) and portions of this steelwork fell down the shaft. Concurrent with the decaying steel work, portions of the shaft lining had collapsed and it was getting progressively worse."

Jan 1, 2019

By K. Webb

At both the international and country level, the issue of how the mining sector and indigenous populations should engage on issues of mutual interest or concern has emerged as one of central importance and controversy; involving the mining industry, Aboriginal communities, governments, the courts, and other stakeholders. At its heart, stakeholder engagement is an ethical issue, although it manifests itself in international instruments, domestic laws, industry guidance and agreements. At the international level, the concept of ?free, prior and informed consent? (FPIC), while not subject to widespread agreement on the finer details of evolving definitions, seems to be emerging as an increasingly recognized engagement norm. Within Canada, through a series of decisions, the Supreme Court of Canada (SCC) has articulated a fiduciary obligation of the Crown to consult with and accommodate impacted Aboriginal groups on resource management issues. Provincial governments have been variously attempting to adjust their resource management regimes to stay in alignment with SCC and lower court decisions. Mining sector organizations, working with First Nations partners, have developed agreements to work together for mutual benefit. At the individual mine and community level, there have been instances of constructive engagement, as well situations of physical resistance and legal challenges. The purpose of this paper is to examine the potential impact of new rules under the Ontario Mining Act introduced in 2012 and taking full effect in 2013, which amongst other procedural specifications, addresses the issue of mining industry-Aboriginal consultation in exploration and development activities. Leading up to the passage of the regulations, representatives from some junior mineral exploration companies have been highly critical of the new rules. Similarly, there have been a range of responses to the new rules from some in the First Nations community. The paper will review the regulation in terms of its apparent alignment with SCC decisions and the international norm, compare the regulations with existing mining sector organization guidance documents, and it will draw on the stated perspectives and commentaries of First Nations communities, mining firms, governments, nongovernmental organizations, and others. Building on the foregoing, the paper will provide a preliminary analysis of the perspectives and potential impacts of the new regulation on various stakeholders, and on that basis, possible avenues for further consideration will be suggested.

Aug 1, 2013

By A. L. Mular

"On behalf of Bob Bruce and myself I would like to begin by stressing some key points.First, most of us know that the Canadian Mineral Processors was formed in 1969 and is an offshoot of the Canadian Gold Metallurgists. I attended that first meeting in 1969, and I haven't missed a meeting since! Pretty obvious that CMP serves the best booze! At any rate, we know that our meetings are supported by CANMET. Camsell Hall is always at our disposal; Bob Bruce acts as permanent secretary pretty much free of charge; we receive a financial grant from CANMET. This brings me to a second point.Second the Canadian Mineral Processors do not enjoy a free ride in this relationship. CMP provides a genuine service to the mining industry, to government, and to universities. For the industry, CMP serves as a forum for the rapid dissemination of new ideas and new technology developed at remote locations throughout Canada. New developments outside Canada are introduced by invited speakers at our meetings. The effect is to help reduce operating costs and increase efficiency.For government, problem areas and research priorities can be isolated through mutual discussions. Direct communication at our meetings can help CANMET to temper its goals and modify its national priorities.For universities, CMP provides a wealth of operating experience and practical know how. The yearly proceedings are a major current reference source fo1· those of us who teach mineral processing. Admittedly, the proceedings are publ-shed from CMP coffers. However, I note that our fees are up this year, which brings me to a third point.Third, we face some potential problems of a financial and political nature. From a financial view, we may lose our CANMET grant and other financial good will simply because of spending constraints. Our fees are expected to climb each year thereafter.From a political view, we know that the metallurgical society of CIM is anxious to incorporate CMP as a section. The pros and cons of such a merger have been described in a recent mailing. In th2 final analysis, the political and financial problems are interrelated. There are several alternative solutions to both problems, which brings me to a fourth point"

Jan 1, 1979

By R. D. Lindsay

Originally the focus of Deak Resources Corporation Business Plan was to establish a method for treating small gold and possibly base metal mineral deposits located in the Kirkland Lake - Noranda area of Northeastern Ontario, Northwestern Quebec at a central treatment facility. Since the establishment of this original business plan in 1988 other processing options have availed themselves for handling the base metal ores off site at a central facility which may preclude their processing at Deak.The site selected for the Deak processing plant was Kerr Addison's Virginiatown operation. At the time this property was acquired from the Receiver following Golden Shield Resources' Bankruptcy in 1989 the mill had been processing in the order of 1, 100 SDT per calendar day through one processing module; a module originally designed to process 1,500 SDT/day of a free milling gold ore. This tonnage level however had not been achieved since 1966 when an average throughput of 1481 SDT per calendar day was recorded.In order to realize Deak's overall Business Plan it would be necessary to expand the mills processing capabilities to provide:(1) A 2200 SOT per day circuit capable of processing a free milling, medium work index gold ore;(2) a 1 ,000 SDT per day flotation and/or cyanidation circuit capable of processing refractory gold bearing materials containing refractory minerals (i.e. copper) that should be removed prior to cyanidation; and possibly(3) a 1200 to 1500 SDT/day base metal circuit capable of processing the broad range of Deaks' Base Metal Property ores. If this circuit were introduced it would be completed in two tonnage phases.Further, it was recognized when operations resumed under Deak in 1990 that the existing tailings dam was suitable for, and had sufficient capacity for additional gold tailings with necessary physical modifications and changes in disposal techniques (including the construction of containment storage cells) that would allow storage for an additional 3.4 million tons of gold ore tailings approximately 1.0 million of which has been deposited since 1990. The focus of Deak's long term tailings disposal strategy is to acquire the Barber Lake Basin which is currently adjoined to our main tailings system which will provide an additional 10 million tons of storage capacity.

Jan 1, 1993

By T. H. North, A. G. Glover, R. J. Pick

"Girth welding operations represent the rate-limiting step in pipeline construction. A joint industry-university program was set up to establish the field welding characteristics of large-diameter, high-strength line pipe.Theoretical work carried out at the University of Waterloo showed that pipe wall thickness and joint misalignment prior to welding has a marked influence on the lifting stresses acting on the root pass of girth welds. Pipe diameter and pipe ovality had negligible effects. Super-position of lifting and residual stress (caused by the fusion welding operation) highlighted regions of the weld bead most susceptible to hydrogen-induced cracking.The field welding characteristics of 1219-mm-diameter, 13.72-mm-wt Grade 483 line pipe were evaluated using a specially designed test rig. The principal test variables were lift height, delay time after root pass deposition, preheat temperature, pipe composition and joint misalignment prior to welding. For any given life, preheat and joint misalignment prior to welding had the most significant effect on cracking tendency.The output of this program has industrial significance and illustrates the beneficial features of university-industry collaboration.IntroductionField welding operations comprise the rate-limiting step during pipeline construction. Crack-free girth welds must be made in a wide range of weather conditions and consequently the field weldability of line pipe compositions directly affects pipeline integrity and construction economics.Pipe-laying practice comprises root bead deposition followed by a skidding operation involving lifting (or lowering) the pipe length onto skid s so that the next pipe length can be aligned prior to welding. Consider pipeline construction using 24.4-m lengths of 1219-mm-diameter , 13.72-mm-wt Grade 483 pipe weighing approximately 10,000 kg. Skidding involves loading a 3-mm-thick root bead by moving the free end of the pipe through vertical distances of up to 700 mm . The likelihood of cracking in these circumstances depends on the inherent crack susceptibility of the pipe composition employed, on the hydrogen content of the deposited weld metal and on how well the joint handles the external stressing caused byskidding."

Jan 1, 1981

By K. J. Brouwer, J. P. Haile

"Construction of the first stage of the tailings disposal facility for the Montana Tunnels Project was completed in October 1986. The project is located 37 km south of Helena, Montana, and involves mining of42 million tons of weathered diatreme are at a rate or 13 500 tpd to produce a gold/silver dore, as well as lead and zinc concentrates. The tailings disposal facility for the project includes a fully drained tailings impoundment for storage of the tailings solids, and a process waterpond for storage of all decanted water prior to recyling to the mill. The over-all facility is designed to achieve the basic objectives ofminimizing seepage to the environment in the short- and longterm, and achieving a fully drained stable tailings mass suitable for immediate reclamation on completion of mining. Specific features of the design include a soil bentonite seal and drainage system within the tailings basin, a free draining embankment with a design flow-through capacity of 4000 US gpm and an ultimate height of 230 ft (70 m), and a soil bentonite lined make-up water pond with a capacity of 420 acre-feet (530 000 m'). The tailings will be discharged in a rotational sequence through multiple spigot offtakes to achieve a thin-layer low energy laminar flow. This 'sub-aerial' deposition results in higher stored densities and maximizes liquid-solid separation on the tailings beaches. The over-all design played a major role in the successful permitting of the project, and was significantly cheaper than a conventional wet disposal system, with overall unit costs for tailings disposal of less than US$0.36 per ton.This paper outlines the site characteristics and the tailings material properties and their influence on the design. Extensive use was made of naturally occurring free draining materials as well as bentonite modified soil liners within the tailings basin, embankment and retention ponds. General construction procedures for the various components are described, as well as on-going construction requirements utilizing materials from the open pit. Finally, the over-all costs and unit costs for tailings disposal are presented."

Jan 1, 1988

By K. Bachmann, M. Rudolph, U. A. Peuker, H. H. Duong, T. Heinig, T. Leißner, H. Schubert, Helmholtz-Institute Freiberg for Resource Technology, Technische Universität Bergakademie Freiberg

"Minerals can be liberated by random fracture of particles into smaller fragments or by detachment along phase boundaries. These two mechanisms represent borderline cases. When ores get comminuted the liberation of minerals is achieved to some extent by both mechanisms. This article describes a method to determine the extent of transgranular and intergranular fracture on surface exposure of minerals based on 2-dimensional liberation analysis.The approach uses the non-biased surface information like phase specific surface area (PSSA), phase specific free surface (PSFS) and phase specific locked surface (PSLS) of minerals and their change with comminution. The amount of transgranular and intergranular fracture on surface exposure can be calculated using the phase specific surface parameters.A sedimentary rock (apatite ore), an igneous rock (nepheline-syenite) and an artificial material (copper slags) were ground to different fineness. Based on the mineral liberation analysis (MLA) of feed and products, the extent of phase boundary fracture on the surface exposure of the minerals is studied.INTRODUCTIONMinerals can be liberated ether by comminution or by detachment (Gaudin, 1939). Liberation by comminution is a random fracture mechanism, which is not being influenced by ore texture, grain boundaries and mineral features (transgranular fracture). Liberation by detachment represents a fracture along grain boundaries (intergranular fracture). Random fracture often is named as the dominating mechanism for the liberation of ore minerals. This has been the basis to simplify models for liberation modelling (Barbery, 1991; King, 1979; Meloy, 1984) assuming that the probability of cracks moving along grain boundaries is zero. Thus, no interfacial area is lost during comminution."

Jan 1, 2016

By K. Webb, M. Hohn

"This paper reviews the evolving Ontario mining regime for mining industry-Aboriginal engagement and its apparent alignment with court decisions, domestic law, emerging international norms, mining industry rules, and mining firm-Aboriginal agreements, drawing on publicly available commentary from government officials, the private sector, and Indigenous communities. This paper provides a preliminary analysis of the potential implications of the new regime, especially for the mining industry and Aboriginal communities and, on that basis, discusses possible future developments.RÉSUMÉ Le présent article analyse le régime minier de l’Ontario pour l’engagement entre l’industrie minière et les Autochtones et son harmonisation avec les décisions des tribunaux, le droit interne, les nouvelles normes internationales, les règles de l’industrie minière et les ententes compagnies minières- Autochtones en se basant sur des commentaires, disponibles publiquement, d’officiels gouvernementaux, du secteur privé et des communautés autochtones. Cet article fournit une analyse préliminaire des implications potentielles du nouveau régime, surtout pour l’industrie minière et les communautés autochtones et, en s’appuyant sur ces données, il traite des futurs développements possibles."

Jan 1, 2016

By A. H. A. Robinson

Until quite recently-practically up to the present time-all but an insignificant amount of the copper produced in Canada was shipped abroad in the form of ore, matte, blister, etc., there to undergo the further treatment necessary to bring it to the refined state in which it is required by fabricators of copper. Consequently, Canadian manufacturers were forced to import nearly all the copper required in their business; and a considerable portion of the ultimate value to be derived from a Canadian raw material was lost to the country of its origin. In the early days of Canadian copper mining, when both the production and consumption of copper in Canada were much smaller than now, such a condition of affairs was perhaps economically unavoidable, and, in any case, was not a matte~ of sufficient importance to attract general attention. Later on, however, when there had been large and rapid increases both in the production and consumption of copper in Canada, it formed the basis of much adverse criticism, deserved or not, of producers of Canadian copper-criticism that became intensified during the war and subsequent years. Happily, the chief grounds of complaint have now been removed, and there are today copper refineries in Canada, either operating or under construction, that are capable, in the aggregate, of turning out amounts of refined copper greatly in excess of any indicated Canadian consumption.

Jan 1, 1931

By G. C. McKerrow

"Mr. G.C. McKerrow, Assistant Manager of Noranda Mines and formerly Smelter Superintendent attended the meeting to answer questions as to why smelters imposed penalties for too much zinc in a copper concentrate or too much copper in a zinc concentrate, etc.D.W. Bridges -Mattagami Lake MinesWhat limits do you set on zinc and lead in a copper concentrate?G.C. McKerrow - At Noranda, we allow 5% zinc free and charge 25 cents for every unit above that. For lead, it is 1% free and 25 cents per unit above that. Lead is a much more harmful impurity than zinc because it tends to recycle more in the smelter circuit and creates a greater health hazard in the plant.E. Thornton - Sullivan GroupWHat harm does fluorine do in the smelting process?G.C. McKerrow - Fluorine usually does not occur in harmful concentrations in non-ferrous smelters. Fluorides are present in exhaust gases in the aluminum and phosphate industries. If these fumes escape into the atmosphere, they may settle out on forage grasses in concentrations that are harmful to livestock.Thorton - Sullivan GroupI have asked this question other places and have been told that it is hard on brick linings and causes gold and silver to be lost up the stack.G.C. McKerrow - Almost any volatile constituent in a smelter charge will aid in carrying other metal values. To this extent it may be harmful.E. Thornton - Sullivan GroupMr. Tait mentioned before a smelter where they have a copper-tin ore and they pay for copper, tin, bismuth and silver but object strongly to indium in the concentrate. Why would this be?G.G. McKerrow - 1 can't see why indium would be a serious impurity. It does tend to concentrate in flu dusts and if you get enough of it you can recover it and sell it but I have never heard of anyone putting a penalty on it.Question - I once ran into a small copper mine in Peru that had cadmium in the copper concentrate but no zinc. The copper smelter charged a penalty for the cadmium. Why would this be?"

Jan 1, 1971

By A. Ingelson

Conflict over mineral development and its impacts on indigenous peoples occurs in many countries around the world. Canada, Bolivia and Peru have experienced mine development for centuries in areas where indigenous communities have been and continue to be affected by the mining industry. On a global basis the mining industry continues to face the challenge of implementing meaningful consultation programs with indigenous peoples. Many governments around the world have adopted sustainable development as a policy and one important element of sustainable development is minimizing social conflict. John Moffet and Francois Bregha (Moffet & Bregha, 1996), in their analysis of the role of law reform in promoting sustainable development, noted that stakeholder participation can reduce this type of conflict. Social conflict can result in expensive litigation and costly project delays for mine developers. Meaningful consultation with indigenous peoples in areas where mine development is proposed can be a critical factor in securing a social licence to operate. A report released by the United Nations in 2005, outlined the elements of a concept called ?free, prior informed consent? (FPIC) that promotes more sustainable development. FPIC provides that mineral exploration and mining should not proceed unless the mining company has secured the consent of the relevant indigenous group(s). This paper employs a comparative approach to evaluate the extent to which three active mining nations, Canada, Bolivia and Peru, require consultation with indigenous residents and adhere to the principle of FPIC. The comparative approach assists in the identification of those consultation elements in the legal regimes of each country that can minimize social conflict in mineral exploration and mine development and therefore contribute to more sustainable development. First, we examine the legal requirements to consult with and accommodate indigenous communities in Canada, a country with a long history of mineral development over a large geographic area that has entrenched in its Constitution the protection of indigenous peoples? rights. We then turn to an analysis of Bolivia, one of the most indigenously conscious mining jurisdictions that has followed the Canadian lead in entrenching constitutional protection for indigenous peoples. Third, the approach to consultation with indigenous peoples in Peru, a nation that has not adopted the Canadian and Bolivian approaches to constitutional protection of indigenous peoples rights, is considered.

Aug 1, 2013

By A. Koning, P. Lauzon

Pressure hydrometallurgy operations require vessels to be lined with an impermeable membrane for corrosion protection and one or more courses of refractory or ceramic brick. Examples of unit operations that utilize composite lining systems include pressure oxidation autoclaves, sulphide precipitation autoclaves, chloride leach reactors, flash vessels, cyclone separators, and direct contact condensers (heater vessels and quench vessels). The refractory lining must satisfy multiple requirements: it must thermally insulate the membrane from process fluid, be structurally stable, provide erosion resistance, be chemically compatible with process fluid, and provide an economic service life. New hydrometallurgical processes are pushing the pressure, and temperature, with each new generation of plants. A fundamental understanding of all factors affecting the mechanical stability of the lining system is essential as lining designs move further away from the industry's experience base. The impact of irreversible chemical swell, operating factors, design factors, and installation factors are presented based on modifications to the traditional one-dimensional mechanical stress model. A new stability criterion - that the brick lining remain in contact with the steel shell membrane - is presented. This new stability criterion imposes new restrictions on the lining design.The effect of geometry and adding additional degrees of freedom to the analysis is explored using two-dimensional and three-dimensional Finite Element Analysis (FEA). The effect of these additional degrees of freedom on the results of the one-dimensional model are discussed.

Jan 1, 2004

By M. Pötsch, W. Schubert

"The kinematic analysis of rock blocks is one part of a block stability assessment. It provides information about a block’s movability, i.e. if a block can detach from the adjacent rock mass and move towards the free space. This paper introduces an analytical method for the analysis of pure rotations of arbitrary finite polyhedral blocks. It enables the engineer to judge a block’s rotatability about a corner or an edge. The method is presented using a graphical and computational method. The application of the method is illustrated with an example. INTRODUCTIONThe kinematic analysis of rock blocks deals with the determination of the movability of blocks. Established methods typically cover: (a) translational motion (John 1968, Markland 1972, Londe et al. 1969, 1970, Goodman & Shi 1985, Warburton 1981) and (b) the specific rotational cases Toppling (Goodman & Bray 1977) and Slumping (Kieffer 1998). Mauldon & Goodman (1990, 1996) and Tonon (1998) introduced rotational kinematic analyses for three-joint pyramids and tetrahedral blocks extending Goodman & Shi’s block theory.All mentioned methods are subject to assumptions that limit the applicability to engineering problems. For example, the kinematic test of daylighting joints or intersections inherently assumes a finite block, which only can be proved by the finiteness theorem (Goodman & Shi 1985). Daylighting of an intersection or plane is not a sufficient condition for removability. Goodman & Shi’s and Warburton’s methods are limited to translational block motion. The methods for block rotations so far address tetrahedral blocks only. They also address only pure rotational modes and neglect the general motion of a rigid body. This paper introduces an analytical method for the analysis of the kinematic rotatability of finite rock blocks. It extends Mauldon's and Tonon's theory of rotatability of tetrahedra to arbitrary polyhedral blocks. A graphical method using the stereographic projection and a computational method are presented."

Jan 1, 2015

By M. Jackson, R. McDonald, T. Osken, D. Robinson

"The addition of sulphidic materials in the leaching of nickel laterites has several potential benefits that include improvements in the rheological behaviour of the blends, reductions in the sulphuric acid and steam requirements, sweetening of the nickel grade of the combined feed material, and the option of using a range of sulphidic materials. The current study examines the oxidative processing of 30% w/w blends of nickel concentrate and nickel laterite ore at 250oC. In particular, the viability of using low oxygen overpressures was examined for significant amounts of nickel flotation concentrate, up to 12% w/w. Further to this the impact of process water quality, in particular the presence of chloride, upon the kinetics of extraction and the mineralogy of the residue were also investigated. This paper will present the results of preliminary work in this area.INTRODUCTIONThe use of sulphidic ore as a source of sulphuric acid during oxidative hydrometallurgical processing is not a novel idea and can be traced back over forty years (Seidel & Fitzhugh, 1968). A series of patents pertaining to application of this approach for laterite ores can be subsequently found (O’Neill, 1973; Opratko et al., 1974; Rodriguez, 2008a, 2008b; O’Callaghan, 2010; Liu et al., 2011) and a few of articles containing published data (Ferron & Fleming, 2004; Quinn et al., 2009). The use of pyrrhotite tailings as a source of sulphuric acid has also been employed for the leaching of converter slags (Perederiy et al., 2011).It is known that hydrometallurgical operations such as the HPAL plant at Murrin Murrin have added small amounts of sulphides as either transitional (mixed sulphide/oxide) ore or non-smeltable concentrate. This can improve the rheology (Rodriguez, 2009) and provide heat credits. However these plants are generally limited in their ability to add such materials due to their reducing nature and given under highly acidic conditions that the breakdown potential of the titanium used for the autoclave lining is significantly reduced. A suitable oxidant must therefore be present to ensure the potential remains sufficiently high."

Jan 1, 2012

By S. Mohammadnejad, M. Olizadeh, B. Mehrabi

A new method using a combination of comprehensive mineralogical and analytical approach which includes optical and electrical microscopy and several analytical techniques with diagnostic leaching has been used to characterize the associations and distribution of gold in a variety of minerals from the Zarshuran refractory gold ore, NW Iran. Zarshuran ore with an average of 7.9 g/t Au-grade and about 8% arsenic with gold recovery less than 20% in direct cyanidation is considered as high arsenic, high au-grade refractory gold ore. In most of the refractory ores, gold is associated with arsenopyrite and co-para genetic ore minerals, while in Zarshuran ore; gold is associated with orpiment, realgar and arsenian-pyrite. Considering its mineralogy and As content, it can be considered as the most difficult refractory ore for characterization and processing. Results from the mineralogical examination and diagnostic leaches indicate that there is only a small amount of free gold (17-19%) that is present in cyanide-soluble sulfo-arsenides compounds, predominantly orpiment and realgar. Diagnostic leaches also indicate that little gold is occluded within the silicate structure (14%). Overall, the gold is mostly included in sulfides, arsenic sulfides and sulfo-arsenides (50%). The results also have shown how the technique can be used to gain a good initial understanding of potential metallurgical problems for a refractory gold ore.

Jan 1, 2005

By E. M. Timoshenko, A. V. Tarasov

The results of laboratory, bench-scale and semi-commercial investigations of a method for adding surfactant (technical-grade lignosulphonate) to the process of pressure leaching of nickel-containing pyrrhotite concentrates have been discussed. Lt has been demonstrated that feeding of technical-grade lignosulphonate distributed along the length of an autoclave ensures a reduction in its requirement by a factor of 1.5 to 2 as compared with single-point feeding; it also results in a decrease by 5% in the unit requirement of metallized iron-bearing precipitator in the process of non-ferrous metals precipitation and reduces by 0.05 to 0.1% (abs.) the nickel and copper contents in the tailings of the given process. Technical solutions have been proposed for commercial introduction of the process.

Jan 1, 2004

By R. W. Pauls

"Many tens of thousands of hectares of forested land will be disturbed and reclaimed in the surface mineable Athabasca oil sands area during the next few decades. The surface area disturbed by Syncrude’s Mildred Lake development alone exceeds 10 000 ha to date. It is not clear that reforestation of disturbed areas will best accommodate the aspirations of all stakeholders, particularly traditional users of the land. A five-year research program by Syncrude Canada Limited and the Fort McKay First Nations has examined the feasibility of raising bison on land reclaimed after disturbance by oil sands development. Forage productivity and carrying capacity for bison was comparable to that of grasslands elsewhere in Alberta. Concerns regarding compaction of newly rebuilt soil by bison traffic proved unfounded. Bison demonstrated weight gains typical for ranched bison and calving rates averaged 90%, a value typical for ranched bison. The animal husbandry problems encountered were typical of those occurring on bison ranches elsewhere in Alberta. An economic analysis indicates that a 1000 ha bison ranch on reclaimed land has a net present value that compares very favourably with a similar area supporting commercial forest. Subject to approval by Alberta Environmental Protection, the current research project will be expanded as a pilot commercial ranching venture in order to explore its commercial viability as a business venture by the Fort McKay First Nations. At the same time, measures will be implemented to resolve various regulatory issues associated with commercial bison production in the oil sands area.BackgroundSyncrude Canada Ltd. (Syncrude) is proposing, in its land reclamation strategy, a feature that is, depending on one’s background and perspective, regarded as an innovative approach to land reclamation, a threat to the regional forest industry, a creative response to aboriginal stakeholder concerns, a reneging on reclamation commitments, an opportunity to provide an ongoing economic base for postoil sands regional economy, or an environmentally unsound use of the land. These diverse and sometimes strong reactions have been generated by the proposal to introduce bison, either free-ranging or commercial ranched, to the reclaimed landscape."

Jan 1, 1999

By M. Dupuis

Recently, a new approach to controlling alumina feeding in a H.H. cell has been proposed [1, 2 and 3]. This approach, labeled In Situ aluminium cell control, is based on a correlation between the slope of the cell voltage during a no feed observation period and the dissolved alumina concentration in the bath. Once the dissolved alumina concentration has been estimated, a primary calibration surface uniquely relating the dissolved alumina concentration and the anode-cathode-distance (ACD) to the cell voltage is used to estimate the cell ACD. Once both the alumina concentration and the ACD have been estimated at the end of the observation period, a PID controller can be used to regulate the rate of alumina feeding using only the normalized cell voltage to calculate the error between the estimated dissolved alumina concentration and a target value. The In Situ aluminium cell control algorithm has now been tested with the Dyna/Marc [4, 5 and 6] cell simulator demonstrating that it should be possible to control a H.H. cell in this manner with less variation in the dissolved alumina concentration and other process variables producing a prediction of improved cell current efficiency and power efficiency.

Jan 1, 2011

By R. K. Jonas

"Pressure leaching and pressure oxidation in autoclaves are important alternatives in the extractive processing of gold, copper and nickel ores. The application of advanced control to pressure leach and pressure oxidation autoclaves could achieve significant benefits as has been shown in alumina pressure leaching. This paper compares and contrasts alumina digestion autoclaves to other mining autoclaves with respect to advanced controls. The application of advanced control in alumina with over 30 units controlled worldwide, and its benefits will be reviewed. The design and potential benefits from advanced control for pressure oxidation and leaching will be presented.INTRODUCTIONIt is this author's position and the purpose of this paper to propose that advanced control could be effectively applied to autoclaves in the nickel, gold, and copper mining processes. This is based on the proven effectiveness of advanced control on autoclaves used in the alumina industry for pressure leaching of bauxite ores. Incremental, but significant increases in production could be realized by applying advanced control to autoclaves, as evidenced by the alumina industry, and this not being implemented in other autoclaves in the mining industry.In addition, today the mining industry is being challenged to improve their production methods. In some markets like nickel, there is pressure to improve productivity and reduce the cash cost per ton. While in other markets like copper and gold, demand is vigorous with favourable pricing, and there are advantages to increase production and productivity given limited plant capacity. Advanced control has proven its capability to improve mineral processing operations through increases in throughput, recovery, as well as reducing variability. In today's mines, autoclaves are being used to a much larger scale and with much larger importance, thus it would be beneficial to improve operational performance through the use of advanced control.Accordingly, it is the author supposition that an opportunity exists in the mining industry to use a proven advanced control technology to improve the operations and financial performance of mines using autoclaves."

Jan 1, 2012

By M. Laframboise, M. Buarzaiga

High-pressure acid leaching (HPAL) of nickel laterites has received considerable attention in recent years. High paymetals extraction, good selectivity, and advances in pressure hydrometallurgical technology are some of the reasons for this interest. Falconbridge Limited (Sudbury. Ontario) investigated the HPAL process using both fresh water and seawater for ore processing. The use of seawater resulted in a chloride concentration of 7.8 g/L in the autoclave feed. A test program was developed to study the effect of process water and leach temperature on the leaching behaviour of different ore compositions from the Koniambo deposit in New Caledonia. The work showed that salinity has a major effect on autoclave chemistry. This paper explores the results.

Jan 1, 2004