Search Documents

By Glen Robertson, Jeff McLaughlin

"The Clarabelle Mill rock tailings have the potential to generate sulphuric acid through chemical and biological oxidation of sulphide minerals. Current rock tailings assay between 0.80 -1.40 %S, with sulphur occurring principally as coarse pyrrhotite. Acid generation within the tailings area can be substantially reduced by segregating pyrrhotite rich tailings in a submerged storage area and by depositing only low sulphur rock tailings in exposed areas. Laboratory tests confirmed that low sulphur tailings could be produced by flotation at reduced pH with a small xanthate addition. A plant test was conducted to evaluate the production of low sulphur tailings in conjunction with INCO's continuing commitment to environmental protection and progressive decommissioning of the metallurgical site.During the plant evaluation, approximately 5% of the mill rock tailings were reprocessed in a line of 100 tt3 Denver flotation cells. Tailing grades below 0.40% S were easily achieved through operation at pH 6 -7, with xanthate addition (dosages up to 0.02 lb/ton) and 10 -15 minutes of nominal retention time. Froth depths between 1 -3 inches combined with relatively liberal amounts of frother were required to pull the lightly mineralized froth into the concentrate which averaged 11% sulphur and less than 5% mass recovery. In addition, three field lysimeters were each filled with two hundred.ton bulk samples of low sulphur tails (0.35% S), standard rock tailings (0.98% S), and mill total tailings (2.30% S) for long term monitoring. The implications for full scale plant design, tailings area decommissioning, the possibility of increased nickel recovery and preliminary field lysimeter data are discussed."

Jan 1, 1994

By T. T. Chen

The iron- and elemental sulphur-rich residues generated during batch and continuous pressure oxidative leaching of Inco Limited's Voisey's Bay nickel sulphide concentrate at 150°C in sulphate-chloride media have been characterized by X-ray diffraction analysis and scanning electron microscopy. The residues produced during the continuous leaching of the pentlandite- and pyrrhotite-rich concentrate consisted predominantly of hematite and elemental sulphur, with minor amounts of goethite. Although the iron species generated in the batch leaching tests were similar to those formed during continuous leaching, the morphologies of the hematite and goethite particles were significantly different. In addition to the tiny spheroids and bubble-like particles, the hematite and goethite generated during batch leaching occurred as larger "hollow" shell-like particles that contained residual pentlandite or sulphur cores. Although the leach solution from which the iron oxides had precipitated contained 5-15 g/L sodium, sodium jarosite was detected only in trace amounts in a few of the leach residues.

Jan 1, 2006

By J. M. Whatley

"IntroductionFEW COUNTRIES equal Canada in the diversity of its mineral output, the range of size of its mine operations, and the extremes of climatic and topographic conditions under which its mining is carried out. Camps large and small are scattered over thousands of miles, some served by excellent communication lines, many in remote regions of the north. Common to most of the deposits is that they are worked by underground methods, and rely on adequate hoisting installations for the success of their operations.Hoisting in some form •pre-dates all other mechanical operations in mines and the hoist remains one of the most important pieces of equipment at the average mine. It provides the single line of communication along which must pass the men and materials to mine the rock, and in turn carry the ore to a place for refinement.Development of Mine Hoists in CanadaCanadian designed hoists were first built and •placed in operation about the year 1880 and have since developed in pace with the rapid growth of the Canadian mining industry. Early machines were all of the steam or compressed-air driven types, of light construction and driven by two duplex slide-valve open-frame type engines. As their application and size increased, designs became more rugged and more efficient."

Jan 1, 1955

By K. P. Wright

THREE OF the gold mines in the Red Lake Camp operates fluid bed roasters in their milling circuits. The mines are Campbell Red Lake, Cochenour Willans, and Dickenson. The roasters are used for the autogenous roasting of a flotation concentrate for subsequent gold recovery by cyanidation. Cochenour and Dickenson operate single stage reactors, whilst Campbell use a two-stage system. Ore treated by the mines is similar in that the major part of the gold is associated with arsenopyrite. Other sulphides present are pyrite, pyrrhotite, stibnite and sphalerite. Gangue minerals are mainly quartz, with carbonates and talc. Mineralization is, for the most part, extremely fine, and there is intimate association between sulphides and quartz, so much so, th at a picked specimen of apparently massive arsenopyrite will frequently contain as much as 80 per cent gangue. Gold recovery by straight cyanidation on this type of ore would not be higher than 80 per cent and

Jan 1, 1961

By E. W. Williams

THE Ontario Research Foundation has developed a process for producing low-density steel shapes by direct reduction of iron oxide powders. The process is a combination of reduction, sintering (without compaction), and carburizing, and has been described by Cavanagh (1). Iron oxide powder, in the form of mill scale or highly concentrated iron ore, carefully sized, is poured into a porous mould. A reducing agent, generally coke breeze, is placed around this mould in a heat resistant sagger which is sealed off and heated to 2,000°F. for a number of hours. The coke/ ore ratio, the particle size distribution, the temperature and time of soaking, and the size and shape of the reduced product, determine the densities and carbon contents attained. The Defence Research Board sponsored a programme of research into some of the mechanical properties of the material (which was named Controlled Density Steel) and this paper is an account of various factors which govern the tensile strength of the steel. The ?practically attainable range of density is from 1.5 to 5.5 gm./ cc. but higher densities are obtained on hot working. This paper, however, is restricted to discussion of results for moulded products.

Jan 1, 1957

By E. C. Keeley

Some Safety Measures at Ontario Mines The following safety precautions have of late been taken by several of the Ontario mines: installation of water crossovers; washing clown of faces to show-up missed holes; insistence on gloves being worn as a protection to men's hands; wearing of safety boots and hats by underground men; and wearing of goggles by all men using hammers, starting holes, etc. In the summer of 1924 the Mclntyre mine began experimenting with means of removing powder smoke from headings by installing fans and pipe-lines of various designs, also with different means of introducing water into the air-blast when blowing smoke. By October of that year they had devised a scheme of water connection between the water and the air line, at a distance of about one hundred and fifty feet back from the face, using two valves and a short hose. By this means a limited amount of water could be introduced into the air which blew into the face, resulting in a fine spray of air and water combined. This spray not only helped to eliminate fumes but also introduced fine particles of water into the air, raising it above the dew point, with the result that when these fine particles of water settled they had attached to them fine dust particles, thus eliminating, to a great extent, the injurious dust caused by blasting. The combined air and water is turned on immediately after blasting and allowed to blow continuously for from four to five hours, until the muckers come on shift.

Jan 1, 1931

By Bai-ru Xia, Cang-qin Jia, Qi-wu Huang

Limit Analysis Theorems has revealed to be a powerful tool for the development of numerical models aiming the determination of the load bearing capacity of structures reached by plastic collapse. This work presents a numerical formulation for the computation of strict upper bounds of the collapse loads of rigid-perfectly plastic mechanical systems, derived within the kinematical theorem framework. A key advance of this present method is that the problem is described only in terms of nodes and discontinuities connecting those nodes rather than element or bodies. The alternative approximation procedure to the traditional finite element method might involve discretization of a given body using a suitably large number of nodes laid out on a grid, with the failure mechanism comprising the most critical subset of potential discontinuities interconnecting these nodes. Potential discontinuities which interlink nodes laid out across the problem domain are permitted to crossover one another, giving a much wider search space than when such discontinuities are located only at the edges of finite elements of fixed topology. Highly efficient interior point method solvers can be employed when certain popular failure criteria are specified (e.g. Mohr-Coulomb). By adopting this processing approach it is possible to solve very large problems which normally exceed the memory capacities of a single computer. The developed numerical tool reveals to be robust and versatile, able to solve a wide range of 2D problems. Velocity singularities are automatically identified and visual interpretation of the output is straightforward. Several numerical examples including rock slope are studied by the new method, and the results are very close to those calculated by using analytical method and FEM.

Jan 1, 2015

By Mark Kennedy, Allan MacRae, Cameron Hams

New technology projects, particularly those involving first-of-a-kind metallurgical facilities, have a poor track record of achieving their overall financial targets, as they incorporate technological risks in addition to normal project risks. Traditional project management tools focus on risk from concept development through implementation, but typically fail to address the additional risks associated with a new technology project including slow start-up, slow ramp-up, and failure to achieve design performance (quality or throughput). These additional risks affect future cash flows produced by the project and hence its value, typically measured as net present value (NPV) or internal rate of return (IRR). Common accounting practice is to reduce the present value of future cash flows by applying a chosen discount rate, often reflecting the corporation's cost of capital. This discount rate does not contain an allowance for technological risk, which is often underestimated or misunderstood by both the financial and engineering project managers. This paper will focus on the topic of project risk and new technology, and how these play a role in the probability of achieving the predicted future cash flows. By properly addressing technological risk in the form of risk-weighted returns, marginal projects can be prevented from proceeding, while sound projects can be given the additional time and resources required to achieve the optimal level of front-end-loading (the level which returns the maximum risk-weighted net present value). A simple set of mathematical tools should enable engineers and financial professionals to establish a common level of understanding, thereby leading to a more accurate assessment whether a new technology project is ready to pass through its next level of approvals.

Jan 1, 2011

By Zoë Mullard

Just as a mine has a lifecycle, employees working within the mining sector also make several transitions throughout their career, from initial recruitment to retirement from the industry. Throughout the employment lifecycle, employees bring skills and knowledge that significantly contribute to the global economy. These skills are developed through education, professional training, coaching and through hands-on experience. Despite the current economic conditions and the demand for minerals, the mining industry is facing a substantial skills shortage due to the disparity between the number of new workers entering the mining industry and a largely ?graying workforce?. Although educational programs continue to evolve to attract people with a wide range of skills, the diversity of jobs and the strains of working in remote mining operations continue to present challenges for recruitment and retention of employees. This gap also presents challenges around knowledge transfer at a corporate and mine-site level; employers will require cultural and techno-sociological approaches to ease through these transitions. At the same time, there has been an explosion of social media tools that facilitate information sharing, cross-organizational collaboration, distance learning and knowledge capture. These tools have become increasingly popular in the last few years and their applications vary widely. The mining sector has started to adopt these tools for a number of purposes, including opportunities to harness social media to enhance human resources interactions, outreach and oversight. This paper will outline several case studies that explore leading practices for how the application of new media can assist organizations and individuals as they progress through their careers. This paper will illustrate how new social media communication technologies can be used to increase employee engagement and build organizational capacity in the mining industry. The paper will also include strategies for how to implement social media to enhance human resources applications and will cover ideas for monitoring and evaluation.

Aug 1, 2013

By Gordon Jackson

"There are two accomplishments of air and gas drilling: a new series of economic and mechanical challenges; and, acceptance as a standard drilling and completion tool.The new challenges are related to the concept of using a gaseous circulating medium in drilling for oil or gas. For purposes of discussion, a two part division has been made: the challenge of fluid invasion control and that of equipment and tools. Great strides have been made in the development of materials and techniques to combat formation fluid invasion. Chemicals and the ""mist drilling"" technique, now in use, have the versatility to cope with a wide range of downhole fluid entry conditions.Equipment and tools have been developed to meet the challenges of better, more economic drilling and completion possible with a gaseous circulating fluid. Economic and operational challenges remain.Acceptance of air and gas drilling as a normal operating tool was reached with difficulty. It is now established as a means of reducing costs in exploratory and develop-mental well drilling, exemplified in a recent study of 226 wells covering 419,407 feet of hole in the United States. Air reached the projected depth in 85 per cent of the operations, although formation water was encountered in 48.7 per cent of the holes. Slim hole bit performance and cost all compared for overall bit averages as part of analysis."

Jan 1, 1961

By A. W. JR. Whitaker

Introduction Within the last quarter of a century the Lake St. John-Saguenay valley has been converted from a quiet agricultural district to one of the important industrial centres in the Dominion. First there was the expansion -of the pulp and paper industry, and then, starting a little over ten years, ago, the development, in large .blocks, of the enormous hydro-electric power resources of the Saguenay river. Coincident with this power development, the world aluminum industry was rapidly expanding and looking for a new source of cheap power. This was found in the Saguenay valley-and so, in 1925, Arvida was established by the Aluminum Company of Canada as a location for one of the largest aluminum plants in the world. Arvida, an incorporated city comprising an area of some ten square miles, is ideally located on a more or less level plateau about 350 feet above the Saguenay river. Seldom has industry stepped boldly forth and carved out of Nature a community with full city status. The process usually goes through the steps of camp, village, town, and city, involving improper planning or lack of planning; all of which has been avoided at Arvida by starting out in the right way. While this community has only a population of approximately 2,000 at the present time, it is carefully planned for a population many times this figure. Streets, city parks, business and residential sections, have been definitely planned, and, with a City government, proper ordinances were passed at the beginning to ensure the building and maintenance of a model industrial community. As the crow flies, Arvida is about 35 miles due east of lake St. John, and 0 miles west of the St. Lawrence river at Tadoussac. From a shipping standpoint, it is well served by the Canadian National railways, with direct lines to Quebec and Montreal, and by ocean shipping facilities at Port Alfred, which is about 15 miles to the east on the Saguenay river and is served by the Roberval & Saguenay railway. The latter has interchange connections with the Canadian National at Arivda, and also operates a branch line into the city of Chicoutimi.

Jan 1, 1933

By J. Álvarez, J. Mesías, C. O. Gómez

"Operations routinely run flotation tests in laboratory mechanical cells to determine adjustments to plant operation based on feed flotation response or the effect of new reagents and dosages. The metallurgical results of these tests are certainly affected by changes in bubble size, which simultaneously impact the recoveries of the collection and froth zones. It is known that bubble size depends on the characteristics and operation of the machine in use, particularly on the gas flow rate delivered to the unit and the selected frother type and dosage. Although flotation rate constants have been related to bubble size, bubble surface area flux seems to be a more fitting variable to correlate flotation kinetics and cell performance, as it integrates bubble size and superficial gas velocity effects. However, although some evidence has been provided, a categorical relationship between cell recovery and bubble surface area flux has not been established. Our interest is to demonstrate this relationship to use it as a basis for developing soft sensors to track on-line collection zone recovery in cells. Flotation tests were designed to produce Cu concentrates for a range of bubble surface area flux values, obtained through changes in frother concentration at a constant gas flow rate, and by increasing gas flow rate at the same frother concentration. The tests were run on samples prepared from an ore batch supplied by a local operation, following strict grinding and flotation procedures, with a shallow froth to approximate cell recovery to that in the collection zone. Bubble sizes were determined using the sampling-for-imaging technique developed at McGill. The results unequivocally showed a consistent positive correlation between cell recovery and bubble surface area flux, and significant variations in performance when frother addition and gas flow rate were changed.INTRODUCTIONMineral flotation is a separation process to produce concentrates of valuable minerals by selective attachment of particles to the surface of bubbles. The process is carried out in machines where air is injected through a mineral pulp to form bubbles, and operated to create two zones: a bottom one (collection zone) where bubbles are continuously generated under conditions adequate to form bubble-particle aggregates by collision of the rising bubbles with suspended particles; and a top one (froth zone) where bubbles and bubble-particle aggregates continue to rise while concentrating and forming a froth layer for water and entrained particles to drain back to the collection zone, before overflowing as a concentrate stream. The phenomena occurring in these zones are complex and, in many cases, interactive, as they simultaneously affect stages of the particle separation sequence occurring in both zones. Although there have been significant advances in instrumentation to characterize particle and bubble populations, these have not resulted in knowledge to explain or models to describe phenomena from fundamental principles. Measurements continue to be limited to the development of empirical models for predicting the effect of operating variables on performance."

Jan 1, 2016

By Peter A. Cain, John C. Folinsbee

"A 4-ft.-diameter shaft has been drilled to a depth of 2,790 ft. in strong, hard, basic Precambrian rocks at Lynn Lake Manitoba. This was done on the property of Sherritt Gordon Mines Limited for the purpose of ventilating and developing the ""N"" orebody, which is located approximately 4,000 ft. south of the Farley shaft.The drilling was done under contract by two drilling companies. Peter Bawden Drilling (1964) Limited drilled the initial 12:1,4-in. pilot hole to a depth of 3,000 ft. Shaft Drillers Limited of Canada then reamed the hole to 4 ft. in diameter to a depth of 2,790 ft. At this point, the reaming was stopped because of the difficulty in passing a change in direction in the line of the pilot hole. The hole was completed by driving a raise 200 ft. from the 3000 level to the bottom of the 4-ft. hole using an Alimak raise climber.Cuttings from the reaming operation were directed into the 12:1,4-in. pilot hole, where they fell to the 3000 level and were removed by a mucking machine and standard mine development cars.The elapsed time from the start of the pilot hole to the completion of the reaming operation was ten months, with an average advance of 279ft. per month. There was a two-month delay between the completion of the pilot hole and the start of the reaming operation.The 12:1,4-in. hole was drilled in an elapsed time of 45 days from the time of setting up the rig. The average advance per day was 66.8 ft.The reaming operation was done in an elapsed time of 194 days. A one-month delay required to repair damaged equipment left 163 days for the drilling and setting-up operation, for an advance per day of 17.1 ft."

Jan 1, 1966

By L. Becze, B. Pierre, S. Di Carlo, G. P. Demopoulos

From January to June 2007, the autoclave production at the Kidd Metallurgical Site was severely affected as a result of plugged discharge lines and extensive precipitation/crystallization of sulphates that caused massive scaling in different autoclave compartments. Work was performed at McGill University to understand the root causes. The crystallization of zinc and ferrous sulphate salts was investigated in terms of solubility measurements. Scale samples were characterized using chemical and mineralogical-spectroscopic analysis. In this paper, following a description of the Kidd zinc pressure leach operation, highlights from this investigation are presented and solutions used to overcome the problem are outlined.

Jan 1, 2008

By J. W. Hohn

The precipitation of Fe(III) to form ferrihydrite in the presence of arsenic is the United States EPA's Best Demonstrated Available Technology for treating arsenic-containing hydrometallurgical solutions and waste streams. This technology has been widely adopted throughout the world and developments have been well reviewed. The adsorption and long-term stability of ferrihydrite can be improved by co-precipitating Fe(III) and Al(III) together to form an aluminum-modified ferrihydrite. Arsenate adsorption into ferrihydrite and modified ferrihydrite as a function of pH, Fe/As or (Al+Fe)/As mole ratio, and the initial As(V) concentration is presented and compared. The results of long-term aging of both adsorbents at 70°C for over a year are also summarized.

Jan 1, 2006

By I. Cotman

Dimensional stone processing has become an important part of the world extractive industry, and today?s total stone block yearly production is estimated to be around 134.000.000 tons and is still growing by an average yearly rate of approximately 20%. In future, the same production will become an important part of the mining industry and presently, in some countries it represents even the main mining output. New environmental regulations, together with landscape and nature conservation requirements, create a number of difficulties in setting up new open pit dimensional stone quarries. As a result, many dimensional stone producers have recently started to apply underground techniques in order to produce the ornamental stone blocks intended for further processing. Underground production of stone blocks requires special mining methods and so far it has not been a cost-effective excavation method for all types of rocks. Presently, this type of stone excavation is generally applied in sedimentary and marble deposits because the rock has small to no mineral quartz content. When starting a new underground dimensional stone mine, it is necessary to analyse the impact of all primary factors which are crucial to set up a technically and cost effective advanced underground dimensional stone mine. The role of physical and mechanical properties of the rock, geological conditions, mineralogical composition, micro-tectonic state of the site, rock mechanic conditions on the site, durability and saw ability of the stone are decisive factors in foreseeing the future methods of extraction. The laboratory research work as well as the field work, is very important in decision-making aimed to choose the future excavation method. Also of equal importance is the serious market research, because it renders the indication of selling price potential. Having obtained the results from both types of research, mining engineers can design the mining methods which optimize financial return to the mine. The practice approved by 15 years of testing in the underground limestone quarry of Kanfanar gives future producers very useful advice and general data to facilitate the process of exploration intended to establish new similar underground quarries.

Aug 1, 2013

By Martin Lebeuf

The phenomena occurring in the cathode and at the cathode surface of aluminum electrolysis cells are very important in regards to cathode voltage drop and cathode wear. In the current study, laboratory-scale aluminum electrolysis cell cathodes were analyzed by X-ray microtomography. This technique allows an excellent visualization of the distribution of different substances, if their respective X-ray attenuation coefficients are different enough. In the current case, the important difference in the mean atomic number between cryolitic bath and graphitic carbon results in good contrasts. The volumetric bath penetration profile, porosity and impurities distribution in the cathode were thus obtained. Furthermore, metallic impurities and bath heterogeneities were observed at the cathode surface. Observations were also made with Scanning Electron Microscopy - Energy Dispersive Spectroscopy (SEM-EDS).

Jan 1, 2011

By J. Illescas, N. C. Murray

This paper provides an economic comparison and technical evaluation of different approaches for copper recovery from small-scale resources such as historic tails, dumps, pond and pit water as well as acid mine/rock drainage. Factors such as the location, the availability and cost of reagents, power availability and cost and a local market for end product alter the preferred processing technique. A number of scenarios are presented and technologies considered include; solvent extraction, ion exchange, sulphide precipitation, cementation, copper sulphate crystallization, membrane (RO) and copper cathode production.

Jan 1, 2014

By A. Warczok, C. M. Diaz, A. Bergman, T. Utigard, M. Barati

The world wide consumption of energy is steadily increasing and by 2030 it is forecasted to grow by another 50%, leading to mounting political and economic pressures. For any pyrometallurgical operation, it is therefore paramount to investigate and implement methods to decrease the use of energy. In the pyrometallurgical processing of steel, copper, nickel and other high temperature metals, a large amount of energy is lost in hot off-gases, molten slags, mattes and molten metals. Most of this energy is generally lost during the cooling and solidification steps with very little focus on energy recovery or reuse. In this paper we will quantify how much energy is contained in the various slag streams, then review previous attempts and methods employed to recover some of this energy, and finally evaluate some novel technologies that could potentially be employed.

Jan 1, 2011

By T E. Tibbetts

This paper deals with coal sampling in general and with mechanical coal sampling in particular. The necessity of obtaining representative samples is emphasized. Other sections of the paper are devoted to the design and selection of automatic samplers, with a consideration of the three main types, and the testing, operation and maintenance of these samplers. The cost of the installation of an automated sampling system must be related to the value of the material to be sampled, to the volume of coal involved, and to the savings in labour and economy which can be achieved. Introduction T HE Committee?:; on Coal Sampling of the Coal Study Subsection, Thermal Power Section (Eastern Zone), Canadian Electrical Association, was established in November, 1963, to "study the various problem areas of coal sampling." The first undertaking of the Committee was to at-tempt to survey the problem areas of coal sampling through an evaluation of coal sampling difficulties as experienced at both the plant design and operational levels within the electric utilities represented on the Committee. The results of this enquiry indicated that satisfactory answers to almost any conceivable

Jan 1, 1965