Search Documents

By L. V. Kin, V. V. Lodeischikov, A. V. Byvaltsev, IRGIREDMET JSC, O. D. Khmelnitskaya, S. V. Petrov

"Irgiredmet Institute carried out the study on the development of gold recovery technology from refractory ore from a Russian deposit. The ore contained 1.1 g/t Au, 1.5% of pyrite and 2.4% of pyrrhotite. The recovery of gold achieved was 84.7% using gravity with generation of high grade recoverable gold concentrate and gravity middling. In the course of lime treatment, cyanidation of the middling followed by tailings detoxification the consumption of reagents was 13.0 kg/t CaO, 95 kg/t NaCN and 72 kg/t Ca(OCl)2 of the concentrate. This was capital intensive.In order to decrease the consumption of reagents, magnetic separation of the middling of the concentrates from gravity separation was added to this flow sheet. Pyrrotite recovered to magnetic fraction, which did not contain gold in accordance to this advanced flow sheet. The mass yield of pyrite goldbearing non-magnetic fraction decreased down to 1.5 times in relative to gravity middling. The slurry filtration prior to and after cyanidation allowed the organization of cyanide solution recycling.The results of pilot plant tests using the developed flow sheet showed that the content of pyrrhotite in the non-magnetic fraction decreased from 59.1% to 11.3%. The reagents consumption was 12 kg/t CaO, 3 kg/t NaCN and 16 kg/t Ca(OCl)2 of the pyrite concentrate. The total gold recovery using this flow sheet was 83.4%. Due to a decreased consumption of reagents, cost efficiency of the process was achieved. Based on the results of this research, a project design criteria was developed. A processing plant with the annual throughput of 2.6 million tonnes of ore is being designed."

Jan 1, 2016

By A. Shakoor, T. P. Gautam

The long-term slaking behavior of clay-bearing rocks in the field can be quite different than the short-term slaking behavior in the laboratory. To assess this difference, 12 replicate samples of each of 20 clay-bearing rocks, including 5 claystones, 5 mudstones, 5 siltstones, and 5 shales, were exposed to natural climatic conditions for 12 months. After each month of exposure, one replicate sample of each rock was removed from natural exposure and its grain size distribution was determined. Disintegration ratio (DR), defined as the ratio of the area under the grain size distribution curve of the slaked material for a given rock to the total area encompassing all grain size distribution curves of the tested samples, was used to quantify the amount of disintegration under natural climatic conditions. DR values of naturally exposed samples were then compared with the corresponding values of second-cycle slake durability index (Id2) determined in the laboratory. The relationship between Id2 and DR after, 1 month of exposure, exhibits an R2 value of 0.65 but the relationship deteriorates when DR values for 6 and 12 months of exposure are used, with R2 values of 0.63 and 0.25, respectively. However, when DR values for laboratory samples, computed from grain size distributions of slaked material after second cycle, are compared with DR values of naturally exposed samples for the three periods of exposure, the relationship improves with the corresponding R2 values being 0.61, 0.71, and 0.41. These results suggest that DR may be a better parameter for assessing the long-term disintegration behavior of clay-bearing rocks than Id2.

Jan 1, 2015

By Han Xing, Cui Jianzhong, Qin Ke, Shao Bo, Zhang Haitao

In this paper, a new approach that uses hot-top DC casting process to producing multi-alloy ingots is present. The different type and size of composite and coated ingots (4045/3004/4045 three-layer composite ingots with section 630mm by 1500mm and 4045/3003 coasted ingot with F140mm/F110mm in diameter) are cast by this approach. The macro-morphologies and microstructures of the composite ingots, the temperature distribution and the element distribution in the interface zone were investigated, also and the interface bonding strength was measured. Results show that the solid supporting layer formed on the cooling plates plays a key role in the casting process of composite ingots. The solid supporting layer can prevent the blending of two melts by resisting the impact of alloy melt, which ensures the stable casting process and casting high quality composite ingots, because the contact height is increased using hot-top DC casting. In addition, fabrication and properties of 4045/3004/4045 three-layer composite ingots with section 630mm by 1500mm are reported in detail.

Jan 1, 2015

By D. G. Sediako

Chemical composition and the casting/rolling production routes determine the cost and properties of the wrought material. For example, the coarse-grained structure frequently associated with DC casting requires complex rolling schedules to refine the grain size. Hot forming (rolling/forging/extrusion) results in a strong crystallographic texture, which is responsible for the tension-compression strength asymmetry frequently exhibited by magnesium alloys. Understanding the influence of alloy composition on texture evolution during forming provides useful practical information to optimize industrial hot-forming technologies for magnesium alloys. In this study, a series of Mg-based alloys containing varying combinations of Al, Rare Earths, Zn, Ca, and Sr were subjected to identical casting and extrusion processes in order to isolate the effects of alloy composition on texture evolution. Textures were measured by neutron diffraction at the NRC Canadian Neutron Beam Centre. The ability of neutrons to penetrate deeply into materials allowed information to be retrieved from all regions of the bulk specimens without destructive and time-consuming sectioning operations, thereby providing true bulk texture data. {1010} , (0002), {1011}, and {1012} pole figures were generated for all of the as-processed alloys, from which Orientation Density Functions were obtained. The were then used to reconstruct the pole figures and to extract semi-quantitative texture data showing how the (0002) and {1010} planes align themselves with respect to the extrusion axis. It was found that varying the concentration of aluminum (3-4 wt%) and Rare Earths (2-3 wt%) in AE alloys had a weak effect on texture development. All of the alloys showed similar magnesium extrusion textures, in which the (0002) poles align themselves preferentially with the extrusion axis. The substitution of Sr for Rare Earths also did not have a significant impact on texture development. On the other hand, while the presence of small amounts of Zn and Rare Earths did not have a strong effect on texture development, alloys with higher concentrations of these alloying additions (in combination) showed an enhanced tendency for the {1010} poles to align themselves with the extrusion axis. The addition of Ca also enhanced the alignment of the {1010} poles with the extrusion axis. These textures can complicate further processing and introduce a significant anisotropy that could influence creep properties.

Jan 1, 2007

By R. U. Seneviratne, B. K. Ahlgren

In this paper we follow various technological discoveries and developments in the purification of minerals and metals in the mining industry by ion exchange. For approximately 100 years, ion exchange has been a known and variously applied purification and separation technology used by scientists and producers. It would seem obvious that the producer’s objectives have always been to achieve the highest quality products and the lowest operation costs, but also with the least amount of technological complexity. As a strategy to reach these goals, much effort has been expended in the quest to improve continuous ion exchange (CIX) systems by reducing utility needs and resin degradation or loss while at the same time improving productivity and reliability. Recent developments from a number of companies have pushed equipment boundaries, resulting in a variety of unique commercial equipment designs each with a varying degree of success. The challenge set forth for all new designs has been a truly continuous process with no sacrifice in the afore mentioned benefits. One very recent equipment design based on system symmetry appears to meet many of these objectives with greater flexibility and less complexity resulting in better economics for the producer.

Jan 1, 2014

By Douglas R. Schmitt

In general, knowledge of the state of stress within the Antarctic lithosphere remains largely unconstrained due in part to Antarctica?s inaccessibility and because of the paucity of seismic focal mechanism solutions. As such, an important component of the ANDRILL project was to acquire new information on the stress directions and magnitudes within the upper crust. Extensive fracture mapping of the core and oriented ultrasonic televiewer logging were carried out to provide strong constraints on both stress orientations and the faulting regime. The first hydraulic fracturing stress determinations in Antarctica were also carried out to provide complimentary stress magnitudes. These measurements were accomplished using a wire-line transported hydraulic fracturing system consisting, essentially, of two synthetic polymer packers that were inflated to isolate the 1-m long pressurization interval. The tests were conducted at the end of the drilling and logging in a ~130-m section specially drilled below 1000 mbsf (nearly 1500 m from the rig floor) for hydraulic fractures. This zone was drilled primarily through competent, dense, and low permeability diamicts. The core fracture and televiewer logging information was used to site twenty separate measurements. Classic hydraulic fracturing pressurization records with unambiguous breakdown and fracture closure pressures were obtained in about half of the measurements. The remaining tests provided fracture propagation and closure pressures that are consistent with the classic breakdown curves, but they did not include a clear breakdown pressure and are indicative of the reopening of either natural or drilling induced fractures in the wellbore wall. The preliminary analysis of the results are in generally good agreement with the stress directions indicated by the core fracture logging and the stress regime suggested by the character of the drilling induced core fractures.

Jun 1, 2012

By L. A. Anestiev

A method based on use of calorimetric data for the determination of solidification kinetic parameters is proposed. The method incorporates recent theories of nucleation and growth and allows modeling heat fluxes observed in calorimetric experiment. Statistically optimal estimations of the kinetic parameters, which include the activation's energies of nucleation and growth, are derived from experimental data by means of nonlinear regression analysis. The method is applicable to pure substances and alloys. The evaluation of the kinetic parameters characterizing solidification of pure Al is used for clarifying and exemplifying the method.

Jan 1, 2004

By D. H. Ryan, J. T. Graham, A. Navarra, J. A. Finch, S. Somot

Pyrrhotite (Po) is widely considered to be the most significant mineral in the self-heating of sulphides. It is therefore desirable to determine the amount of Po in mineral samples. This is commonly accomplished through x-ray diffraction (XRD) or quantitative evaluation of materials by scanning electron microscopy (QEM-SEM). This paper introduces another quantitative method based on Mossbauer analysis that requires limited sample preparation and has the additional potential to detect the sulphur/iron ratio within Po. The technique is explored using pentlandite/pyrrhotite mixtures.

Jan 1, 2009

By S. Makni, G. Gagnon, F. Couët, C. Rochefort

"Comminution represents a significant part of mineral processing plant operating costs. Yet, autogenous (AG) or semi-autogenous grinding mills (SAG) are difficult to control because of disturbances like feed size distribution and rock hardness. AMIRA, within project GeMIII, developed a comminution index from laboratory crusher data. The index correlated with the Bond ball mill work index and with the A×b parameter. The present work extends the use of crusher data as a grindability indicator to real-time industrial applications. The aim is to improve comminution operation using online hardness estimation. Because the operational work index is proportional to the ore work index, rock hardness variations can be estimated from the feed and product size distributions, the throughput, and the power draw of a crusher. Real-time estimation of rock hardness can help understand the dynamic behavior of AG and SAG mills. Multivariate time series were analyzed to understand the impact of hardness on a SAG operation. Results showed that the estimated hardness influences the SAG operation and its throughput. Moreover, non-linear dimension reduction was used to ease the process visualisation and search for potential control strategies. In the future, online hardness measurements should also impact the understanding of comminution circuits and improve their operation.INTRODUCTIONThe variability in hardness, and the feed size distribution, are two of the main disturbances affecting comminution circuits (Sbarbaro & del Vilar, 2010). Size distribution can be measured by imagebased granulometry systems such as WipFrag (Maerz, Palangio, & Franklin, 1996), or by 3D vision systems when the fines are difficult to discriminate by 2D segmentation (Faucher, Makni, Gagnon, Lavoie, & Roberge, 2015).There are few examples of online hardness measurements. One example was the work of Casali et al. (2001) who developed a hardness indicator. The ore grindability soft sensor used the fraction of each lithological class in the ore, as determined by image analysis, to predict the work index of the material. The model was developed using a moving window with a width of 12 months and trends were shown over many years with one data point per month."

Jan 1, 2016

By S. Klemmer

Potential problems associated with groundwater inflows are a major concern to many Saskatchewan mining operations. Rock mass behaviour and stability have been linked to groundwater inflow potential. An estimate of the hydraulic conductivity of the rock mass is an important factor for assessing groundwater inflow potential. This paper presents a procedure that was developed to conduct air permeability tests, for estimating the hydraulic conductivity of the rock mass. Tests were conducted near underground excavations with the goal of assessing links between measured air permeability, rock mass classification and the rock mass response to adjacent excavations. Measured changes in air permeability corresponding to the distance from excavation boundaries may indicate changes to joint properties such as joint aperture, continuity and frequency. This study outlines the instrumentation, the experimental and analytical procedures, and the preliminary results from testing.

Nov 1, 2011

By J. M. Réjean Gagnon

"Quebec Cartier Mining Company is currently mining a low-grade iron ore deposit in northeastern Quebec. The Company is producing some 8,000,000 dry gross tons of concentrates per year, grading about 66 per cent iron. The pit, which is located on the keel or hinge line of a fold, will eventually be about 1,000 feet deep with a surface area of 8,000 by 2,600 feet. The most significant structural discontinuities in the mine are the natural bedding planes and secondary perpendicular joints. The exposed walls are subjected to a sub-Arctic climate and heavy blasting occurs approximately six times a month.QCM utilizes design and operating techniques to control rock fall. Steps are also being taken to analyze the ultimate over-all pit slope stability."

Jan 1, 1968

By Chris Carr

This paper describes the process employed and the work undertaken to enable the surrender of the mine permit relating to the two tailings deposits at the abandoned Red Mountain Mine site near Rossland, BC. The first phase of the work undertaken was to provide urgent remedial work for protection of the environment, primarily through rehabilitation or replacement of surface water drainage systems. The second phase was to up-grade the water management systems to the appropriate level given their consequences of failure. The final phase of work is to ensure long term geotechnical stability of the facilities to the same level of risk. Establishment of a sustaining fund will facilitate long term monitoring and maintenance of the facilities.

May 1, 2002

By Dan Miners

"This presentation will provide an overview and understanding of Mine Safety and Health Administration (MSHA) and Ontario Regulations for Mines and Mining Plants. It includes discussions on the history and practical development of the standards and an overview of engineering best practices from a construction, maintenance and operational viewpoint. INTRODUCTION Ontario is one of the safest mining jurisdictions in the world and has some of the most comprehensive regulations for the construction, operation and maintenance of a mine. In the USA, several operators have adopted some or all of the practices prescribed by the Ontario Regulations as an internal procedure. Experience has demonstrated that these plants are indicating less unplanned downtime and fewer issues with MSHA inspectors in their hoist plants. HISTORY AND THE REGULATIONS Both Canada and the USA have had some form of laws governing the operation of mines since the late 1890s. The paths of legislation have run in reasonably parallel lines, continually improving the health and safety conditions in the mining industry. Ontario Mine Health and Safety In the 1970s the accident rates in mining were higher than any other industrial sector; this prompted a Royal Commission on the Health and Safety of Workers in Mines (the Ham Report). The recommendations of this report, published in 1976, generated several changes in the regulations regarding worker safety in mines. Following the release of the Ham report, the Occupational Health and Safety Act (OHS) was passed by the Legislature in 1978. The Act is a set of comprehensive laws governing almost all Ontario workplaces, and it replaced separate laws governing different industrial sectors. OHS is enforced by the Ministry of Labour (MOL), and this discussion will focus specifically on Ontario’s Occupational Health and Safety Act, R.R.O. 1990, Regulation 854, Mines and Mining Plants, Part X Mine Hoisting Plant (Ontario Regulations). USA Mine Health and Safety A coal mine explosion in West Virginia and medical studies on occupational disease led to the 1969 Federal Coal Mine Health and Safety Act (Coal Act). The Coal Act was the most comprehensive and stringent Federal legislation governing the mining industry to date. The Mining Enforcement and Safety Administration (MESA) was formed, following the 1973 Act, as a new departmental agency to assume the enforcement of safety and health in mines. The Federal Mine Safety and Health Act of 1977 (Mine Act) transferred enforcement responsibilities from the Department of the Interior to the Department of Labor and named the new agency the Mine Safety and Health Administration (MSHA). This agency enforces the Code of Federal Regulations (CFR), and this discussion refers to CFR Title 30 Mineral Resources, Chapter I Mine Safety and Health Administration, Department of Labor, Subchapter K—Metal and Non-metal Mine Safety and Health (MSHA)."

Jan 1, 2019

By Edward P. Barrett

Iron ore, when subjected to reducing gases at a temperature suitable for reduction of the oxide but not high enough to melt the ore or metal formed, is converted into metallic iron. The product, being the original piece of iron oxide minus its oxygen, is sponge-like in appearance when viewed under a magnifying glass, and hence is called 'sponge iron. Sponge iron was probably the form in which some of the first iron was recovered from the ores. As early as the eighth century the Catlan forge developed into a low shaft furnace known as the high bloomary, in which iron was produced in the form of a pasty mass. These furnaces were increased in height, and with increased temperatures came the production of liquid cast-iron, at first undesirable because of lack of knowledge of methods for working it. In 1340 the first true blast-furnace was built iri Belgium. Some castings were made, but the greater part of the iron was converted into wroughtiron blooms by a crude puddling process. Charcoal was the universal fuel until the latter part of the seventeenth century, when coke was first used in England. Larger scale developments of methods of refining pig-iron followed. In I 885 Bessemer built his first converter in England, and within a few years the Siemen' s regenerative open-hearth furnace was developed, also in England, to produce steel. Then followed the enormous expansion in the metallurgy of iron. The idea of a direct process for the production of iron and steel has persisted during all of this time.

Jan 1, 1925

By W. M. Armstrong

THE GROWTH of the major iron and steel industries on this continent and in many European countries was based on the use of as-mined, high-grade, lump iron ores and on the availability of metallurgical coking coals. The modern coke-fired blast furnace was developed for such materials and is one of the most efficient of ail pyrometallurgical processes. Most of the impure pig iron produced by blast furnaces was converted to refined steel by the Bessemer process in the years prior to 1900 but, when large quantities of low-cost steel scrap be-came available, the more flexible open hearth process was adopted by most large steel producers on this continent. Although this pro-cess has many desirable metallurgical features, the thermal efficiency is low, the capital cost is very high, and the method of charging scrap steel is inefficient by modern standards of material handling. In recent years several conditions have arisen which have stimulated the development of many new pro-cesses and the re-examination of the existing smelting and steelmaking techniques.

Jan 1, 1958

By A. Pawelczyk, D. Hreniak, E. Zych, W. Strek, K. Grabas, A. Ostrowski

"Mongolia is a country rich in rare earth resources. In the experiments carried out samples of the Mongolian ore were processed to obtain a lanthanide concentrate. The concentrate underwent hydrometallurgical processing. At the same time radioactive elements were removed. The lanthanides were obtained in the form of hydroxides that were further processed in order to get concentrated products. As a result cerium, lanthanum and neodymium-praseodymium concentrates were separated in the process. Also a concentrate of remaining elements: samarium, europium, gadolinium, terbium, dysprosium, holmium and erbium was obtained. INTRODUCTIONAccording to the assessment of the US Geological Survey, Mongolia possesses 16.77 % of the world total rare earth (RE) resources (Daly, 2011); that is the second largest RE reserve in the world, estimated to be 31 million tonnes in terms of rare earth oxides (REO). In the face of Chinese RE trade restrictions, Mongolia emerged as an important economical partner in mining and exploitation of these critical raw materials. This country is recognized as having more than five large RE deposits in the southern provinces. The most important are Lugeengol (Lugin Gol), Mushgia Khudag, Khotgor and Khalzan Buregtei (Eurasia, 2010). The Mongolian government has taken measures to facilitate western investments, nevertheless the country is economically dependent on China, the basic trading partner, particularly where exports are concerned.In the late 1970s Hydromet Kowary Enterprise, Poland, took up, along with the Wroclaw University of Technology, research and technological study on lanthanides recovery from raw materials of Vietnamese and Mongolian origin and from Indian monazite sands (Kowalczyk, 1990; Kowalczyk & Mazanek, 1987; 1990). For that purpose, a rare earth processing plant had been constructed with the capacity of about 10 t/year of hydroxide concentrate. The facility included several technological operations like grinding, flotation, hydroxide concentrate production in the hydrometallurgical processing, particular RE separation, and production of commercial products in form of CeO2, La2O3, Nd2O3, Pr2O3, and misch metal. Additionally work had been carried out in Kowary on the manufacture of yttrium and europium oxides of high purity, which were intended for color TV picture tube production in Poland."

Jan 1, 2012

By R. H. Duthie

As at any other mine in Canada, grade control procedures are used at Steep Rock Iron Mines (1) in order to ensure that concentrator and pellet-plant operator s have a uniform feed so that they can manufacture a pellet to suit buyers' specifications and (2) to maximize ore recovery so that as little as possible finds its way to the waste dump or is downgraded by contamination. At Steep Rock, material grading 40% to 66 % Fe is considered ore. The ore may contain up to 10% sulphur. These ranges create six different stock pile types, with the possibility of more if large concentrations of arsenic are encountered. Although grading and mining techniques used to accomplish these ends are fairly standard, there is an appreciation and willingness by hourly and staff pit personnel to make grade control effective. This produces vertical and horizontal communication, which is necessary for success in this field. At Steep Rock, the waste-to-ore ratio is greater than at any other iron ore mine in Canada. Also, a high percentage of the ore mined is direct pellet feed. For these reasons, .grade control is very important.

Jan 1, 1977

By W. Dietzel

Fracture mechanics based techniques are used to gain insight into the phenomenon of stress corrosion cracking (SCC) and to develop guidance for avoiding or controlling SCC. From constant extension rate experiments under rising load or rising displacement conditions the susceptibility of high strength steels, aluminum, magnesium and titanium alloys to SCC and hydrogen embrittlement can be assessed. Such tests on pre-cracked specimens are also well suited for studying the mechanisms leading to SCC by employing appropriate models for the degradation of metallic materials which take into account the uptake of atomic hydrogen from the corrosive environment. Measurements of crack growth resistance curves using the crack tip opening displacement as fracture parameter can be compared with simulated R-curves obtained from modeling of the mechanism of hydrogen embrittlement. The materials investigated are a high strength steel and a magnesium alloy both exposed to environmental conditions which fostered the uptake of hydrogen.

Jan 1, 2010

By G. W. Govier

The origin and limitations of the conventional and empirical equation for the interpretation of the results of back pressure tests on gas wells are discussed. Difficulties in data interpretation arise from many causes, including Jack of flow stabilization, uncertainties in connection with the friction calculation, and the effect of turbulence near the sand face in the reservoir. A procedure is developed to ac-count for the turbulence effect. This is based upon the theoretical equation for laminar steady state flow and current knowledge of turbulent steady state flow. The procedure involves the expression of the equation for combined laminar-turbulent steady state flow in terms of a turbulence contribution factor. This factor. is shown to be dependent mainly upon the flow rate per unit of pay thickness and the reservoir permeability. The method of interpretation permits the use of judgment based upon the theory and present day under-standing of laminar-turbulent flow and is considered an improved method

Jan 1, 1961

By W. P. Campbell

In the course of the development of the Red Coulee field, northwest of Coutts, Alberta, a considerable amount of information has been gathered by the Department of the Interior regarding the chemical character of waters encountered in the drilling of wells in this area. The writer, in this paper, has undertaken to assemble the available material with the idea of deducing what relations, if any, may exist between the different waters from the same well, and also how these compare with waters encountered in similar horizons in other wells. From no other district, with which the Department of the Interior has had to do, have there been received so many samples of water, and yet not all the waters logged in the drilling reports were sent in for analysis. The information, therefore, herein contained is not as complete as the writer would have desired, but sufficient evidence has been accumulated to indicate some very definite tendencies in the chemical nature of the waters of this field. The drilling of Red Coulee wells has been carried out exclusively by percussive tools. These permit 'dry' drilling, and, consequently, water-sands are recognized when encountered. Had rotary tools been used, information regarding water-sands would have been very meagre, if not entirely lacking, since, in the mudding-off process, water-sands would have been overlooked, with the result that, should water break through into a completed well, its source would not be known and remedial efforts would be greatly handicapped, if not entirely defeated.

Jan 1, 1931