Search Documents

By D J. Gray

The 4 km long Huguenot Toll Tunnel in the Western Cape region of South Africa celebrated its tenth anniversary on 18 March 1998. At present a single (South) bore with bi-directional traffic flow is operational. The North bore was originally excavated but not lined and equipped.The tunnel is fitted with a semi-transverse ventilation system comprising 45/350 kW two speed fresh-air and 1 MW exhaust air fans at each of the portals. These provide ventilation through fresh and exhaust air ducts above the ceiling separated by movable partition doors. Secondary air ducts deliver air at low level. The fan control depends on the levels of CO pollution or visibility measured at six positions along the tunnel.The system performed well during initial tests and under conditions of low traffic volumes. As traffic volumes increased, and user complaints of bad air in the tunnel were received on several occasions, we realised that we had a problem. Tests confirmed that natural airflow within the tunnel induced by prevailing meteorological conditions outside the portals affected the performance of the ventilation system causing a plug of bad air to be trapped at varying positions along the operating tunnel.The control systems in the tunnel are presently being upgraded as described by Gray, Rieckert and Bullock (1998). As part of the retrofit we are implementing a new control strategy for the ventilation system which takes into account the external weather conditions. This paper discusses the 24 month long meteorological data gathering exercise, which is on-going, and explores the philosophies planned for controlling the ventilation system. The correlation between winds external to the tunnel and induced airflow inside the tunnel are examined. The effects of the weather induced airflow on the existing ventilation system are considered and proposals given for taking these effects into account in the new control strategy. These include the implementation of an expert system to predict ambient airflow from prevailing weather conditions, and the use of airflow measurements taken in the uncompleted North bore as a cross-check.The paper highlights the need to take cognisance of external weather conditions when designing tunnel ventilation systems.

Jan 1, 1999

Alfred Nobel first invented a practical detonator in 1863 and then the blasting cap in 1865. At that time the detonator was used on the end of a length of safety fuse to initiate nitroglycerine-based explosives. Since then the detonator has gone through a number of changes. The instantaneous electric detonator was the first to allow remote firing. The electric delay detonator followed and allowed for timing between holes. In the mid 1970s the NONEL« Tube was invented. This tube combined with NONEL« detonators meant that many of the safety issues, such as stray current and radio frequency, associated with electric delay detonators were eliminated. This system gave the mining industry a reliable and fairly accurate system with which to detonate shots of any size. Since the early 1980s a large amount of research and development work has been done around the world to create a more accurate detonator for the mining and quarrying industry. After years of research, electronic detonators have emerged as the most accurate and precise initiation system available to the mining and quarry industry today. Electronics provide the user with millisecond timing accuracy. The improved level of timing control allows operations to improve fragmentation, throw and reduce vibration levels. There are now a number of different electronic detonator suppliers on the market today. In 2004 Dyno Nobel formed a joint venture called DetNet with AECI. DetNet has a suite of electronic detonators: DigiDet«, HotShot« and QuickShot«. This paper will focus on the HotShot« system, the first of the three new initiation systems to be released to the market in Australia by Dyno Nobel.

Jan 1, 2005

By C Dowding, C Aimone-Martin, P Abeel

This paper presents measurement and analysis of the dynamic response of a five-storey building to very high frequency excitation (>100 Hz) from blasting vibrations originating from a contiguous excavation of rock. Velocity response measurements in the rock and on the structure were employed to calculate the time-correlated dynamic displacement response of the building to blasting. Time-correlated structure response measurements are needed to advance the understanding of the response of urban structures to high-frequency excitation. Current regulations and understanding are based upon measurements of the response of one- to two-storey residential structures by 10 to 40 Hz excitation. The extension of these observations to taller structures when excited by high-frequency excitation needs to be investigated further.Measurements show that the amplification patterns at the ground level and top of the structure match or are lower than that observed by the US Bureau of Mines (Siskind et al, 1980) for the shorter residential structures. They decrease with increasing peak particle velocity. From the measurements, the global transverse shear strains found by differentiating ground floor and top displacements were calculated to be 12 µstrains. Time-correlated bottom and top of structure displacements show that building response may be more reflective of wave propagation up the structure than whole-structure inter-storey drift.In addition, a 3D model was used to compare computed displacements and strains to measured results. Modelled responses varied considerably, both in magnitude and location of the maximum strain. No conclusion can be made regarding the best 3D model to employ to simulate building response. More data such as motions measured at many points in the structure are needed. Maximum inter-storey transverse shear strains calculated with the model were found through the acceleration excitation and were less than 12 µstrains for 37 mm/s rock motion excitation. The inter-storey transverse shear strains calculated with rock displacement input were less than that found with the acceleration excitation.CITATION:Dowding, C, Aimone-Martin, C and Abeel, P, 2015. Measured and modelled response of a multistory, urban structure to high-frequency blasting excitation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 211–220 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By L Galisson, E Audigé, D Sowers

Establishing a robust geotechnical instrumentation and construction monitoring plan is one of the keys to the successful delivery of the world’s largest soft-ground bored tunnel in Seattle, Washington. The paper describes and provides a return of experience on current and best practice for monitoring tunnelling projects in urban areas. The owner’s contractual approach is discussed to highlight the flexibility of the design-built contract in achieving equal or better solutions by allowing for the use of innovative technics. Special attention is given to the management and involvement of third parties (building owners, utility owners), including the public, to overcome all challenges faced during the installation of the monitoring system in downtown Seattle for over 1000 instruments. Finally, the authors present the strategies implemented for managing the monitoring data and communicating with the owner, contractor and stakeholders.CITATION:Sowers, D, Galisson, L and Audigé, E, 2014. Current and best practice for monitoring tunnelling projects in urban areas – Alaskan Way bored tunnel, Seattle, Washington, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 441–450 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By D Walker, A Tsvetkov, P Voigt, O Kloiber-Deane

The GPM Gold Operation has been employing an Albion Process™ plant at its Sotk (Zod) gold mine in Armenia since 2014. Long term data from the operation is now being published for the first time. The data presented includes concentrate throughput, as feed to the Albion Process™ plant (tonnes per day), sulphur grade in concentrate (% S), total sulphide sulphur oxidation in the Albion Process™ plant (% SOx) and gold recovery from Albion Process™ plant residues (%). The data provides a basis for evaluation of the effectiveness of the commissioning, ramp up and operation of the Albion Process™ plant. Notwithstanding the impact of a slower concentrator commissioning than expected, the plant demonstrates Series 1 behaviour on McNulty ramp up curves, indicating successful commissioning and fast ramp up. Interrogation of the data and operational experience indicates that this successful operation is a result of a process that is flexible, robust and stable, one that was designed well based on solid testwork results and pilot plant trials during the study phase undertaken by Glencore Technology and Core Resources, and where the local operators were provided with appropriate training in operation of the plant. CITATION:Voigt, P, Walker, D, Kloiber-Deane, O and Tsvetkov, A, 2018. Ramp-up and long-term performance of the Albion Process™ plant at GeoProMining Gold Armenia, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 339–350 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By G Tsatouhas, R Newell, K Y. Wong

A sulfide ion selective electrode was used to control sulfidiser addition in the flotation testing of a synthetic and a naturally occurring ore containing malachite in order to compare the behaviour of sodium sulfide and calcium polysulfide. Both slug and controlled potential sulfidisation methods of addition were used. Under defined optimum CPS conditions, calcium polysulfide was a more effective sulfidising agent than sodium sulfide on the basis of both capital and operating costs. Surface and solution studies were used to compare the mechanism of each sulfidiser. For calcium polysulfide, XPS showed that polysulfide ions are adsorbed, whereas for sodium sulfide it is the hydrosulfide ions that are adsorbed on the mineral surface. For calcium polysulfide, the CuSx layer was believed to form on the malachite surface, which promoted the flotation of the malachite, by xanthate. Studies of surface morphology of the sulfidised malachite showed that a fairly uniform sulfidised layer is formed with both reagents. The use of sodium sulfide resulted in a thinner initial sulfidised layer compared to polysulfide at equivalent initial sulfur concentration.

Jan 1, 2005

By R Grobler, D Burger, L Alberts

The current climate in the mining industry is allowing mining companies to further broaden their views and investigate technologies to improve the safety, efficiency and cost-effectiveness of their operations. Furthermore, underground mine environments will become more demanding for mining equipment and personnel as orebodies become deeper in weaker ground conditions with more extreme environmental conditions. Loading and hauling can represent significant components of the production cycle of an underground mine and automation of these activities can offer considerable benefits. Sandvik has accumulated a long history and experience in loading and hauling automation in underground mining. Since the late 1980s Sandvik has actively participated in several major research and development automation programs leading to the commencement of the development of an integrated system for semiautomated loading in 1999. Development work was later conducted to expand the capabilities of the system for automated hauling during 2001 and the AutoMine« system became commercially available. The first delivery of the AutoMine« system was completed in August 2004 in South America, where the system continues to operate in a full-scale production environment and is being expanded as the production area enlarges. Further systems have been delivered and are operational in North America, Africa and Europe. This paper focuses on the AutoMine« system deployed in Block 4 at De Beers Finsch Mine in South Africa. An overview of the mine and the process used to acquire the system and the key drivers which led to the selection of an automated solution are described. An overview of the initial system installation, subsequent expansions and future plans are presented. This is followed by a summary of the implementation and operational experiences associated with automated underground operations. The paper concludes by summarising the benefits that have been realised.

Jan 1, 2008

By M Nagarajan, S Esen

This paper presents three case studies from three surface coalmines. The first case study is from a coalmine where a dragline operates in 60 m wide and 1 km long strips. Typical overburden height ranges from 30 m to 50 m. The base case blast was modelled using an advanced blasting model (Distinct Motion Code – DMC) to establish the baseline using the blasting parameters in use before optimisation. DMC was used to model the alternative blasting scenarios to obtain the following key objectives:the post-blast muck pile profile was required to have an optimum height of ~28 moptimise cast percentageachieve a well-fragmented muck pile for the draglinethe muck pile profile should be appropriate for the dragline entry into the strip.Achieving these objectives would optimise the dragline performance through reducing rehandle and improving advance along the strip. DMC modelling resulted in the following outcomes:the required muck pile profile could be achievedthe cast percentage increased from 21.1 to 25.1 – a four per cent increaserehandle volumes were reduced.Establishing a good quality assurance / quality control (QA/QC) process was essential to delivering a blast that could achieve these outcomes. The blast was fired successfully and the dragline completed the strip approximately two weeks ahead of the time taken for the previous strip.The second case study is from a coalmine where D11 dozers are used to move the blasted material to the spoil. An optimum profile was required for the dozers for this low-cost mining operation. To achieve this, an electronic blasting system (uni tronicTM 600) was introduced to optimise the muck pile profiles being delivered. The new muck pile profiles showed improved cast percentage from 10.6 per cent to 17.8 per cent. The changes in the muck pile centre of mass displacement improved dozer efficiency as a result of pushing material shorter distances to its final position. Dozer productivity (bcm/h) statistically did not change but coal was being exposed at a faster rate.The third case study summarises the results from a site where dozers are used to minimise the total mining cost. Traditionally, excavators had been used on-site with conventional blast designs. After firing the first cast shot, the blasted material was found reasonably well-fragmented. Although dozing productivity hasn’t been quantified on-site, operators were providing positive feedback (easier push) due to the reasonably good muck pile profile suiting to the dozers. This site also realised significant savings with the dozing as compared to their truck/shovel operation.CITATION:Esen, S and Nagarajan, M, 2015. Muck pile shaping for draglines and dozers at surface coalmines, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 409–416 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

MIM Holdings Limited has acquired a reputation for the successful application of R&D to develop break-through technologies for the mining industry. The Isa Process tank-house technology has been licensed to copper refineries throughout the world, and almost 40 per cent of the worldÆs copper is refined using this technology. Isasmelt copper and lead smelting technology is either in use, or is currently being installed, by eight companies in eight countries around the world. Jameson Cell technology is widely used in the coal mining industry and increasingly in the base-metal industry. The IsaMills developed at Mount Isa and McArthur River made it possible to develop the McArthur River and George Fisher orebodies. This paper will address the need for innovation and then discuss the development of the IsaMill and Isasmelt technologies. It will conclude with some comments about why MIM has been so successful in developing such technologies.

Jan 1, 2002

By E Rubio, N Morales

Currently, mine plans are optimised by using several criteria as objective functions, like profit, life-of-mine, concentration of some pollutants, mining costs, confidence level or ore resources, with consideration of constraints related to production rates, plant capacities and grades. Whilst this approach is successful in terms of producing high value production schedules, it uses a static opening sequence of the drawpoints and therefore the optimisation is made within the level of freedom left by the original opening schedule, and as a result it is far from the true optimal value of the project. This paper presents a model to optimise the sequence of drawpoint opening over a given time horizon. The emphasis is in the precedence constraints that are required to produce meaningful operational sequences considering the exploitation method (panel or block caving), physics considerations and logical rules. Further on, while it applies the standard approach of maximising net present value (NPV), it considers other targets for optimisation, like the robustness and constructability of the plans. Finally, it applies the model to real data to obtain feasible plans by means of this model. The first tests were done varying the production capacity of the mine.

Sep 26, 2011

By A Riles

"Three issues of relevance in a modern tailings storage facility (TSF) are:geotechnical stabilitymanaging acid rock drainage (ARD) from pyritic tailingsmanaging the tailings from cyanidation of gold ores. Drawing on examples from both copper porphyry flotation and sulfide-hosted gold ores, this paper demonstrates that giving some weight and importance to the process tails properties upfront can influence the flow sheet and not only improve tailings management effectiveness but also impact positively on economics. In the case of a typical copper porphyry ore with moderate pyrite content, the rougher tail in a conventional high pH selective flotation step is usually classified as potentially acid generating (PAG). To avoid the generation of ARD within the tailings and the requirement for a costly plastic lining, subaqueous deposition is recommended, which in turn has negative implications for tailings stability, consolidation and closure. Adopting a neutral pH rougher stage rejects silicate gangue but recovers pyritic material to the cleaners for a subsequent selective flotation stage, often after regrinding. This effectively quarantines the PAG pyritic material in a much lower volume cleaner tail, which can then be appropriately encapsulated within a larger non-lined flotation tails facility. It also facilitates cyanide leaching of the cleaner tail for gold recovery, with the encapsulated tailings facility being suitable for cyanidation tails storage. A case study from Europe is examined. For gold ores where the gold is sulfide-hosted, but not refractory, a flotation route with cyanidation of the concentrate can similarly produce the majority of tailings as a benign flotation tail and again quarantine the low volume concentrate leach tail in a small encapsulated cell with appropriate residual cyanide management measures applied. Overall economics for intensive leaching of a low volume concentrate stream can also be surprisingly positive. A feasibility study design example of the process and TSF is presented. CITATION: Riles, A, 2016. An Integrated Approach to Optimising All Concentrator Products, Including Tailings, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 341–346 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By D Johansson, A Nordqvist, D Mihaylov, N Petropoulos, M Wimmer

The flowability of the caved rock masses in the sublevel caving (SLC) mining method is of great importance. During the blasting process of a SLC-ring, the caved rock mass in front of the ring is compacted. As a result of this compaction, the mechanical properties of the fractured rock masses change, for example void ratio, angle of internal friction and structure of the compacted material. The changed mechanical properties of caved rock mass and recent blasted material can influence the mobility of the material, which could result in blockage of the flow path of the material. The identification of the involved mechanisms in this process can be done after a series of tests in different scales. However, there is no available equipment for dynamic measurements during blasting, ie velocity and displacement of the burden and in the caved masses. This study focuses on the development and laboratory evaluation of a measuring system that can be installed in a borehole. The first trial was carried out in a pillar, where two blastholes had been drilled (9.5 m) parallel with the drift and two measuring holes (16.5 m) were perpendicular to the drift. Two measuring systems were installed in the measuring holes. Some preliminary tests were carried out to find suitable initiation procedures for the emulsion explosive. Applicability and robustness of the developed measuring system were also evaluated. In addition to these tests, an expandable cement mixture was developed to firmly anchor the measuring systems in the boreholes. The measuring system consists of an anchor, armoured cable in a pulling tube and a protective case. The anchor is equipped with uniaxial and triaxial accelerometers. A potentiometric measuring system for displacement up to 2 m is installed at the end of the pulling tube and connected to an extendable spiral cable. All sensors are connected to a data acquisition system (DAS). Both measuring systems have their own DAS to acquire data in case of failure of one of the systems. The measuring system was tested in laboratory conditions with impact velocity up to 10 m/s. It was proven to be functional and gave reliable results.CITATION:Petropoulos, N, Mihaylov, D, Johansson, D, Wimmer, M and Nordqvist, A, 2015. Design of equipment for dynamic burden measurements, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 493–500 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J Mukhopadhyay, J Gutzmer

Most world-class high-grade (60 - 67 wt per cent Fe) hematite iron ore deposits are the product of enrichment of Precambrian iron-formations but processes responsible for enrichment are still unclear. Different models, ranging from syngenetic and diagenetic (King, 1989), deep-seated hydrothermal (Powell et al, 1999; Barley et al, 1999; Taylor et al, 2001; Gutzmer et al, 2002) and ancient supergene (Morris, 1980; 1985; Van Schalkwyk and Beukes, 1986) to modern supergene (MacLeod, 1966) have been suggested. The high-grade hematite deposits stand in contrast to martiteûgoethite ores which are generally accepted to be the result of supergene enrichment of iron-formation because they are found along Cretaceous to Tertiary lateritic weathering profiles (Morris, 1980; Harmsworth et al, 1990). Uncertainties about the origin of the high-grade hematite ores appear largely due to the monomineralic composition of the ores. They are almost exclusively composed of hematite (as microcrystalline hematite and martite), a mineral with wide stability field and very simple chemical composition that reveals little about its origin. Second, many of the deposits have been overprinted by later deformation and chemical weathering obscuring primary ore characteristics and zonation (Taylor et al, 2001). Third, surprisingly few detailed geological studies have been undertaken on the deposits with the aim of unraveling ore genesis. Most studies focus on the present-day structure of orebodies and their general physical-chemical composition for mining and beneficiation purposes. A more thorough understanding of the origin of high-grade hematite iron ore deposits may be gained by combining available mining-orientated data with systematic petrographic-geochemical analyses of different ore generations and hematite phases. This paper presents a first summary of results of an ongoing study, started some two years ago, of high-grade iron ore deposits in South Africa, India and Brazil, including a comparison with the rather well studied deposits of the Hamersley Province in Australia.

Jan 1, 2002

By R Hargreaves, C Morley

The authors often see problems on mine sites that are due to insufficient feedback between technical discipline silos as the realities on the ground fail to inform the models and plans used to drive resource exploitation. Resource modelling, reserve definition, life-of-mine planning, short-term mine planning and scheduling, mine operations and beneficiation operations are all processes that inform each other, but in many instances feedback between these processes occurs in an ad hoc way and only after problems have come to light.Universal reconciliation uses a multidisciplinary approach across the entire mining value chain to identify both opportunity and loss of value and to maximise operational performance. This paper will look at the operational effectiveness of universal reconciliation and will outline the important elements that make it successful, including how to map out the detail underpinning modelling, planning and execution processes. We do this by documenting the physical processes, logical work practices, organisational roles and responsibilities, data origin and quality, working assumptions and information management practices at an operation. The results quickly show how misinformation and assumption causes suboptimal decisions to be taken, where inefficiencies exist and what the opportunity is to remedy these issues.A universal reconciliation study opens up an opportunity for stakeholders to reassess how the operation should be run and how operational effectiveness should be measured. Clear envelopes for reconciliation become obvious and questions about the practicality and data quality can be addressed.A reconciliation code of practice is a key element of a successful universal reconciliation project and the authors outline the important aspects that will provide an operating model, showing the effectiveness of the resource and reserve modelling, the practicality of the mine planning and scheduling practices, how well the mine operations team are executing these schedules and how effective the processing area is given what it is fed. Most importantly, a system that allows operations time to react before the losses become systemic and that is based on identifying early warnings from hard data when these processes start to wobble is outlined. Finally as a case study, the revenue and cost benefits resulting from universal reconciliation diagnostic projects for nine mine sites is documented.CITATION:Hargreaves, R and Morley, C, 2014. Universal reconciliation – a multidisciplinary approach across the entire mining value chain to identify loss of value and maximise operational performance, in Proceedings Ninth International Mining Geology Conference 2014 , pp 411–420 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By D E. G Connelly, K Y. Wong

Gold at the Harbour Lights Mine (HLM), WA occurs principally in pyrite (Py) and arsenopyrite (AsPy) minerals rendering it inaccessible to direct cyanidation. Froth flotation produces a concentrate with low mass recovery and with high recoveries of sulfides. After investigating several alternatives, a novel flotation process has been developed to separate the concentrate into pyrite and arsenopyrite rich fractions. The pyrite fraction is finely ground and cyanide leached, while the arsenopyrite is treated off-site. This paper describes the separation process from laboratory bench scale through to commercial operation at the HLM gold plant.

Jan 1, 2005

By M Lynch, B White

The historic city of Charters Towers in North Queensland is underlain by an extensive labyrinth of old mine workings in a large number of flat lying, subparallel, main and cross-cutting cross reefs extending of the order of 5 km along strike and down to a depth of 700 m in parts. These old workings produced over 6.6 million ounces of gold at a grade of over one ounce to the tonne prior to closure in 1920.Citigold is progressing the development of a modern, high productivity, low cost new mine to extract extensions of these reefs as well as other as yet un-mined reefs. To do this it is changing the paradigm for operating in such circumstances. This paper first briefly reviews the setting for the development and then discusses the philosophies and concepts that Citigold is proposing to use, harnessing technology to create a mine that exemplifies more productive and safer mining based on operating in the digital age.The paper addresses how a modern approach is being applied to the planning of a mechanised, deep, narrow vein, hard rock gold mine under a city. It also describes briefly the successful æexperimentationÆ with longhole open stoping methods developed at the companyÆs small underground operation (the Imperial Mine) to the south of the city, which will also be expanded substantially as part of the Charters Towers Gold Project.The paper also addresses the development of new and/or modified technologies in the venture, with the objective of pursuing continuous and autonomous mining methods. The company is adopting a holistic systems approach, addressing people, process and technology in order to efficiently identify and locate the high-grade ore zones and then extract them effectively at a high grade by minimising waste development and haulage, dilution and energy consumption, and with minimal environmental impact.CITATION:Lynch, M and White, B, 2013. Brave new world autonomous mining systems, in Proceedings World Gold 2013 , pp 157-166 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

To solve the mining safety and health needs of the future, access to, and sharing of, timely and relevant information will be crucial. The next generation of the Web will provide tools (RDF, OWL, SPARQL, etc) to define and link content for more effective discovery, integration, and reuse across applications and organisations. A recent Gartner Research Report (Finding and exploiting value in Semantic Web technologies on the web, May 2007) predicts these technologies will begin to coalesce in ten years. Implementing this Semantic Web requires structured web content described via metadata (information about information). If an industry or enterprise bases its metadata on a common vocabulary, it becomes possible to share and reuse information. The National Institute for Occupational Safety and HealthÆs (NIOSH) Mining web site provides access to more than 1500 NIOSH-developed publications, products, and topic pages on issues as diverse as ground control, respiratory diseases, and mine emergency management. As the site has grown, locating content has become increasingly difficult. To improve the searching process, a panel of internal experts representing all major research programs was established to develop a controlled vocabulary for indexing that content. The outcome is the NIOSH Mining Safety and Health Thesaurus, a faceted, hierarchical thesaurus containing hundreds of mining safety and health terms organised into 20 facets (eg diseases, injuries and disorders; hazardous events and exposures, equipment, engineering and administrative controls). One immediate goal of this project is to reduce the complexity of locating information on the NIOSH Mining web site by implementing metadata and faceted information retrieval techniques. Another goal is to stimulate discussion in the international mining community regarding developing metadata standards so the industry is ready to adopt future Semantic Web technologies to improve access to mining safety and health information.

Jan 1, 2008

By A Golsby

Although much talked about, social licence to operate (SLTO) is a relatively new concept that has been deemed as one of the four biggest business risks to a mining project over the life-of-mine. There is no accepted single definition of SLTO and this author understands SLTO to be stakeholder perception of the legitimacy of a project, a company or an industry. At a specific site, and across different sites within the same organisation, SLTO ranges through different levels according to stakeholders’ degrees of acceptance in time and space. Management of SLTO is vital for the mining sector but is difficult as it is informal and intangible. Although there are no key performance indicators, there are certain indicators that enable relative measurement of the ‘level’ of the SLTO. Because of the importance of the SLTO, information management during the entire life-of-mine, from exploration to rehabilitation, becomes crucial for the continued operation of a project. This paper identifies ten basic principles for the management of information to support the SLTO.CITATION:Golsby, A, 2014. Managing information to support a social licence to operate, in Proceedings Life-of-Mine 2014 , pp 389–398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By K Friese, H P÷llmann

Clinoptilolites, modified with sodium, produced a material which has been tested for the ability to remove Hg (II) from aqueous nitric acid. The amount of adsorption depends on contact time, acid concentration of aqueous solution and initial mercury concentration. The study of the kinetics of mercury uptake revealed that all sorbents exhibit a fast rate of sorption. The highest sorption capacities were observed for sodium forms, and were up to five times higher than for the unmodified zeolite. The maximum sorption capacity toward mercury is determined as 0.093 ¦g/g at an initial concentration of 10.0 ¦g/L for a clinoptilolite from Tsagaantsav deposit (Mongolia). The sorption of Hg (II) has an ion-exchange nature and consists of three stages, ie the adsorption on the surface of microcrystals, the inversion stage and the ion exchange in the interior of the microcrystal. Sorption capacity decreases with the increase of mercury concentration. The presence of other metal ions such as Cd (II), Cu (II), Ni (II) and Zn (II) increases Hg (II) uptake capacity. Finally, sorption for Hg (II) was investigated in batch systems to evaluate the short-term stability of the sorption properties.

Jan 1, 2008

Hard rock TBMs are very often open machine layouts, with just a part roof shield over the front of the machine. The whole system is designed for fast face advance and the economy of the project often depends entirely on the rate of advance. Typically, hard rock conditions will demonstrate stable and good ground for a major part of the tunnel. However, short sections of crushed shear zones with clay and gouge material may cause serious time delays. Spiling rock bolting has been proven to be very efficient under such circumstances, provided the fully grouted rebar bolts can be placed in a controlled and practical manner.Environmental restrictions are becoming more and more a part of tunnel excavation projects. Even hard rock TBM tunnelling may require a strict ground water control, because of consequences on the ground surface from lowering the ground water level. Such consequences may be surface settlement, negative influence on ground water resources or damage to vegetation.Pressure injection ahead of the advancing tunnel face (in this paper named pre-injection), using microfine cement and chemical grouts, is today a proven technology. As examples can be mentioned (Garshol, 1997) about 100 km of pre-injected tunnels below Oslo City and about the same length of subsea tunnelling elsewhere in Norway. Examples from other parts of the world are also available, like below Stockholm, Sweden, the Inland Feeder project and Hollywood Metro both in Southern California.To take advantage of spiling rockbolts and pre-injection, it is an obvious prerequisite to be able to drill the necessary boreholes in the right positions and at the correct angle. In drill and blast excavation this is simple, but in TBM projects it has repeatedly turned out to be difficult. More than once owners have accepted bids containing reassurance from the contractor that the drilling method will be sorted out later. Experience shows that if ælaterÆ means after start of the TBM operation, it is often too late.

Jan 1, 1999