Search Documents

By N DavT

Pyritic tailings from the Quirke mine waste management area in Elliot Lake, Ontario were subjected to long-term column leaching experiments in two PVC columns measuring 122 cm in height and 15.2 cm in diameter. At the end of the leaching experiments, the columns were taken apart and sampled at 5 cm intervals for quantitative mineralogical and geochemical characterisation. Each column is represented by a total of ten samples. Polished sections, prepared from the samples, were studied by optical microscopy, scanning electron microscopy, electron microprobe and X-ray diffraction techniques. Mineral quantities were determined based on linear mixing models of whole rock and mineral compositions. Pyrite particle sizes were measured by image analysis interfaced to an electron microprobe. The tailings are coarse-grained (ie 96 per cent passing 75 ¦m) and composed of quartz, K-feldspar, muscovite and pyrite. Pyrite is homogenous and occurs as liberated particles displaying angular to subangular boundaries with strong dissolution features at the end of the leaching experiments. Based on up to 3518 particles measured in a sample, pyrite particle sizes range from 1.7 to 78.6 ¦m. Pyrite concentrations vary from 0.1 to 7.8 wt per cent, depending upon their location from the top of the columns. These correspond to pyrite losses of up to 99 per cent from their original level of 7.2 wt per cent in the upper half of the columns. Pyrite oxidation rates in terms of moles of pyrite oxidised per mole of pyrite per square metre per second were calculated from the effluent data and the measured pyrite particle sizes. The rates vary from 1.71+10-12 to 5.78+10-10 mole+m-2+s-1 within the 1.5 to 3.5 pH range for 10 ¦m particles. These results are comparable with the published oxidation rates at pH 2 where the dissolved oxygen is the only oxidant.

Jan 1, 2003

By E R. Ramanaidou

The value of Raman spectroscopy to undertake mineral and chemical characterisation of iron ores was assessed by applying the technique to representative samples of banded iron-formations (BIF) and a BIF-derived, martite-goethite ore. The common iron oxides haematite, magnetite and goethite as well as gangue minerals such as quartz and carbonates all show distinct Raman spectra that enables these phases to be easily detected and mapped in situ for either samples prepared as polished blocks or unprepared material. Raman spectroscopy also offers the potential of in situ chemical characterisation. Shifts in the excitation bands of carbonate detected in BIF were related to the Mg content of Fe-carbonate and confirmed the first world-wide occurrence of a high Mg-bearing siderite (pistomesite) in BIF.The discriminatory power of Raman spectroscopy coupled with the potential of the technique to offer large-scale (volumetric) characterisation of iron ore will be of great value not only to the existing BID and CID ore types, but also to the newly emerging magnetite iron deposits (MID).

Jul 11, 2011

By M Paine

Work to date has shown that the use of Al2O3:SiO2 ratios is suitable for identifying potential gibbsite bearing samples. Subsequent confirmatory XRD analysis helps to refi ne this initial identification. Based on these methods, gibbsite has been mapped in two common settings:1. along steeply dipping faults, or2. in association with stratigraphic contacts where one unit is aluminous (eg dolerite dyke).On a microscale, the samples studied illustrate an association between haematite, and to a lesser extent goethite, and gibbsite. In these samples the dominant forms of haematite are discrete crystalline phases of either microplaty haematite or euhedral martite. Two dominant forms of gibbsite were observed:1. vein style gibbsite that cross-cuts (or infill’s cracks) in goethite ± martite iron oxide associations, or2. gibbsite intimately intergrown with and forming a matrix to microplaty haematite.Some of the gibbsite microstructures observed suggest that it may have formed during a very hydrous, possibly hypogene, stage of the deposit genesis. The presence of this crystalline gibbsite, and in particular its occasionally euhedral form, suggests that aluminium was at some stage remobilised, at least locally, and then precipitated from solution as gibbsite. These observations suggest that these has been a phase of gibbsite precipitation that may have had a close but complex relationship with regards to the timing of the mineralisation processes, rather than formation as a result of late stage lateritic weathering.

Jul 11, 2011

By D Oliveira

The use of an equivalent continuum for a rock mass is not always suitable for situations where the failure is structurally controlled by discontinuities as in the case of wedges in the tunnel roof. In these instances, discontinuum approaches are usually preferred. Rock joints that are filled with soft infill are likely to be the weakest planes in a rock mass, having a dominant influence on its overall shear behaviour. In this case, the joint material model adopted for the discontinuities should be able to describe important mechanisms, such as asperity sliding and shearing, post-peak behaviour, asperity deformation, and the effect of the soft infilling. The latest version of a soil-infilled joint model is discussed here. It describes more comprehensively than previous models the occurrence of dilation and compression with lateral displacements, and also represents the hardening mechanism related to asperity interference as observed in the laboratory that cannot be readily captured by the existing joint models. An analytical approach for the analysis of rock wedges structurally controlled by soil infilled joints is presented.The analytical approach presented in this paper for assessment of symmetric rock wedges in the roof of a tunnel demonstrates, that the peak shear strength of the joint may not be fully mobilised before detachment of the wedge. The analysis verifi ed that an overestimation of the factor of safety may be observed when an elastic-perfectly-plastic joint model was assumed, whereas the computed maximum factor of safety was considerably less when adopting an appropriate soil-infilled joint model.

Mar 8, 2011

By Marton A

The Readymix Group have a Quarry Improvement Program - 'Building in Quality (BIQ) which has many parallels to the ICI Explosives' total quality management - 'Quality Improvement Program' (QIP). Both companies have for some time recognised that the 'do it right first time' principle means less wasted effort and materials, that efficiency breeds profitability and so actively promote the quality culture. To install the principles and generate the culture requires considerable commitment and effort from the top down and invariably spreads to the suppliers and sub-contractors. Understanding the component processes involved with the quarry operation, analysis of those processes and gaining a breakdown of the cost of non conformance then allows the astute quarry operator to make the necessary changes to improve the process to realise profits. This paper outlines the steps in such a process and the profitable outcomes of the commitment to continuous improvement at the Nickol Bay Quarry.

Jan 1, 1994

By D Reid, A Fourie, J Ayala

This paper discusses cone penetration test correlations for loose gold tailings that were developed within a critical state soil mechanics framework. The development of a new calibration chamber for cone penetration testing that consists of a modified triaxial cell is described. Some of the early development and commissioning issues that were encountered, as well as the solutions adopted are outlined, including the system to prepare the samples and to acquire high-quality data from the testing. Also, the triaxial laboratory testing required to achieve the critical state line is described, including some of the basic precautions considered necessary as good practice. Additionally, the system adopted for volume tracking of the calibration chamber sample is described, which is essential for ensuring a reliable state parameter comparison against the acquired cone penetration test data. Finally, some laboratory test data from the calibration chamber is plotted against the soil behaviour type charts currently available from various authors.

Jul 1, 2021

By C Itotoh, K O’Halloran, L Karlson

Global methods used to explore for minerals have progressed relatively slowly since the development of the first diamond core drill in 1863. Since then, key developments such as wireline geophysics (1920s), the tricone drill bit (1930s) and aeromagnetic surveys (1940s) all occurred in response to global events. In this project, BHP’s WAIO Geoscience operations team hypothesise that a global movement towards a greener future as well as an increasing intolerance for safety events will drive another step change in exploration methods. We have leveraged our relationships with exploration contractor partners and industry leaders to develop a realistic vision for 2033 and beyond, where drill rigs, earthworks and geophysical units are operated and maintained remotely; emissions of dust and waste are eliminated; hazardous energy sources are controlled; procurement is based on sustainability rather than cost and carbon emissions are tracked with the same rigour as production metrics. We have combined these visions into a series of graphical illustrations with the aim of inspiring ourselves, our vendors and our peers to collaborate further on producing a step change in our industry.

Sep 18, 2023

By G Reynolds, N A. Ware, L Lu

Queensland Pacific Metals (QPM) is progressing its Townsville Energy Chemicals Hub (TECH) project to produce nickel and cobalt sulfates for advanced battery materials. Apart from the nickel and cobalt sulfates, the process also generates a hematite by-product (~640 ktpa). The hematite byproduct precipitated from the process, hereafter ‘hematite precipitate’, is high in Fe and particularly low in impurities. However, it is a fine <20 μm crystalline, hydrometallurgical precipitate and is produced as a filter cake containing a high moisture content of about 15 per cent. This is considerably different from natural hematite ore and is expected to change its performance during sintering. In the present study, laboratory scale sintering tests were undertaken to evaluate the potential impacts of substitution of the hematite precipitate for traditional magnetite concentrates and further for Australian hematite-goethite ores in a simulated industry base blend. Substitution of hematite precipitate for magnetite concentrates was found to slightly increase the sintering temperature required to achieve the strength of laboratory sinters. However, further substitution of hematite precipitate for Australian hematite-goethite ores slightly reduced the sintering temperature required to achieve the laboratory sinter strength. These results reflect the reduction in Al2O3 contents of the blends and are consistent with the trend observed in industry and pilot scale facilities. The reduction in sintering temperature generally correlates to a reduction in fuel rate in the larger scale sintering process. The pore structure of selected laboratory sinters was further examined and discussed in conjunction with sinter strength. The pore structure images highlighted the relative difference between the blends with the most obvious difference being seen at 1290°C which correlates well with the laboratory tumble index (TI). The laboratory sinter samples showed an increase in porosity and irregularity of pore shape, as hematite substitution increased demonstrating the correlation between a more porous structure and a lower TI.

Sep 18, 2023

The Porgera gold mine has made significant progress with the successful installation of a JK FrothCam image analysis system. The system is used to measure and control froth velocity on the scavenger circuit which has brought significant economical and operational benefits. The froth velocity signal, determined by analysis of the camera, is transmitted to the PLC that manipulates flotation cell airflow rate and cell level controllers to maintain a target froth velocity of 130 mm per second. Following on from a three-week trial installation in June 2000, a permanent installation was commissioned on the scavenger Outokumpu (OK150) tank cells. Further work is in progress on the rougher Wemco cells. This paper describes the evaluation of FrothCam Technology and its subsequent installation.

Jan 1, 2003

By G Kennewell

At 11 am Monday 8 September 1997, the successful detonation of the 5/9 Mass Blast at Pasminco - Elura was signified by the subsiding of æMt KevinÆ (a 15 m high earth fill mound). The blast was in response to earlier mine subsidence, which holed through to the surface affecting future stability of underground workings. The blast was a first for Elura which fires small tonnages regularly to avoid rapid oxidation of the ore. This paper discusses the strategy and the considerable planning that went into EluraÆs first blast of this magnitude in order to succeed first time round.

Jan 1, 1999

By D van der Spuy, T Kewe, K Keet, N Moffatt, A P. Paine

The Blue Cube Mineral Quantifier Inline (MQi) instrument uses reflective light spectroscopy and advanced chemometrics to measure mineral or elemental grade in a slurry line. The instrument takes scans continuously and sends data to the DCS or PLC control system.Controlling the concentrate grades on a flotation circuit using low-frequency measurements can be difficult or impossible, especially on a circuit that has fast process dynamics. The ability to rapidly measure changes in grade makes it possible to continuously manipulate the flotation circuit operating parameters such as level, airflow and reagent addition set points to optimise plant performance throughout changing conditions.At Barrick’s Porgera mine in Papua New Guinea the flotation circuit feeds sulfide concentrate slurry to a pressure oxidation circuit. In order to maximise gold recovery in the flotation plant and increase performance in the pressure oxidation process, there is a stringent requirement to maintain a stable and optimum sulfur grade. The gold recovery is directly affected by the sulfur grade as most of the gold at Porgera is submicroscopic and associated with the sulfides (disseminated?pyrite).Porgera considered various points in the flotation circuit for installing Blue Cube analysers. This was part of a plant upgrade to improve process control. Due to budget constraints it was decided to initially only install one Blue Cube analyser on the final concentrate stream of the flotation circuit measuring sulfur, sulfides, gold and particle size. The accuracy of the calibration results were very good for all these properties. The sulfur measurement was used in an advanced control system to optimise and stabilise the grade. The paper presents comparisons between mineral grades determined using analytical laboratory analyses and the online Blue Cube data measurements, as well as benefits achieved by measuring grade online. An analysis of the plant data before and after installation of the Blue Cube and the advanced process control upgrade indicate that the flotation recovery increased by 1.98 per cent.CITATION:Kewe, T, Moffatt, N, Strobos, P, van der Spuy, D, Paine, A P and Keet, K, 2014. Evaluation of the Blue Cube MQi slurry analyser for application in an advanced control system for the optimisation of a gold sulfide flotation circuit, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 357–362 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By K Banerjee, C Dube

Veolia Water Technologies was contracted by a global coal mining company to design a retrofit acid mine drainage treatment facility using DenseSludge™ technology on a former coal refuse disposal site. The project constraint was to reuse current facilities in order to reduce additional capital work cost and avoid additional footprint requirements while improving treatment performance and reducing sludge production and chemical consumption. The initial installation of 454 m3/h served as a pilot plant to demonstrate the benefits of the process and ultimately provided design criteria for the new facility. The pilot demonstrated the benefit of the technology by reducing sludge volume by 90 per cent compared to conventional processes currently in use. The sludge that is reinjected into the mine contains less water, which reduces the volume of water that returns to the mine pool for treatment and mine water balance. Furthermore, the pilot plant reduced lime usage compared to conventional processes by operating at a lower pH set point, demonstrating steady pH control and stoichiometric lime utilisation.CITATION:Dube, C and Banerjee, K, 2015. Sludge conditioning technology to reduce sludge and the cost of acid mine drainage treatment, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 105–110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By D Yan, D Connelly

Beneficiation of magnetite is an integral part of the future of iron ore processing. Historically, the focus of Western Australian producers has been on exporting direct shipping ore (DSO) namely haematite. The future for new DSO resources is limited so companies are changing their emphasis into processing the very large, undeveloped magnetite ores in Western Australia (WA), using beneficiation to produce shippable magnetite concentrates. These magnetite resources require higher cost processing techniques such as fine grinding and beneficiation to produce saleable concentrates. This distinct difference, from the DSO ores, has led to the development of a number of new technologies. This paper reviews: the different techniques used for magnetite beneficiation and provides some case studies in the WA industry; the use of mineral liberation analysis (MLA) to describe the nature, grain size, occurrence and associations of the mineralisation;the consideration of coarse cobbing as a critical upgrading; the application of high pressure grinding rolls (HPGR) to save energy; how the field of magnetic separation has resulted in new machines with higher field strength (SLon Separators); ultra fine grinding requirements of magnetite concentrates; andthe application of reverse flotation to reduce silica in the concentrates.

Jan 1, 2009

The purpose of this study was to investigate the effectiveness of froth fl otation for the recovery of gold from the gravity tailing stream of the former Lihir Gold Limited (LGL) operation in Ballarat. The P80 of the tailings was determined by screen analysis as 1 mm, with test work conducted on as received material along with samples ground to P80 sizes of 47, 78 and 134 microns. Laboratory scale batch flotation tests were conducted at both natural and elevated pH to investigate the impact of pyrite depression on gold recovery. Results indicated that although an increase in grade from approximately 0.7 g/t to 3 g/t was achievable at a natural pH and a P80 of 134 micron, gold recovery was low at just 35 per cent. Finer grind sizes were found to have an adverse effect on both grade and recovery. Future efforts will be focused on the sub 310 micron size fraction of the tailings, which was revealed to contain approximately 85 per cent of the available gold and may be amenable to cyanidation or ultra-fine gravity treatment.

Aug 1, 2010

Development of a global failure criterion for rocks has been a desired goal in rock mechanics. Due to variations in factors affecting rock specifications and their mechanical properties, proposing a single failure criterion suitable for all rock types has proven to be unachievable. The theoretical failure criteria do not fit the real data correctly. Amongst empirical criteria, the Bieniawski criterion has demonstrated an acceptable agreement with laboratory generated data. It has been experienced that the ability to estimate rock strength via the modified form of this criterion is significantly improved. Based on the modified Bieniawski criterion and using VB.net, an associated Microsoft Windows program named &apos;RAMOCE&apos; has been developed. The inputs of RAMOCE can be triaxial compressive strength data, Bieniawski parameters of a specific rock or the type of given rock. Based on input data, potential outputs of the program are Bieniawski&apos;s rock parameters, sensitivity analysis of the effective parameters, rock failure prediction and defining the type of given rock.

Nov 25, 2010

By K Seddon

Segregation of tailings on deposition can occur as a result of a) sub-aqueous deposition, and b) sub-aerial deposition at lower solids concentrations (i.e. when the solids concentration is less than the segregation threshold). The effects are likely to be more pronounced in the case of subaqueous deposition.This paper presents the results of an investigation of a sub-aqueous tailings facility.Data from the investigation show extreme variations in particle size and density compared to test results for non-segregated ‘all-in” tailings. The results indicate that on segregation both the fine and coarse splits tend towards a well sorted (poorly graded) mix, and both have significantly lower consolidated density than the all in tailings. This result is reasonably well known for the case of the segregated fines (“slimes ponds”) but less appreciated for the coarse fraction. The results suggest that if the effects of segregation are not allowed for, the overall density of the deposit can be seriously over-estimated at the design stage. Also the quantity of water retained in the tailings can significantly influence water recovery and water balance results.CITATION:Seddon, K, 2018. Segregating tailings – effects on density and water retention, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 299–308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

Production targets are the basis for almost every decision made by operations personnel in the daily operation of a concentrator. It is the production targets that determine how the plant is operated and therefore determine its efficiency. However, to achieve maximum plant efficiency production targets must be relevant to the process and achievable.In RoseberyÆs case, for many years, production targets were taken from budget data which, with the exception of mill feed tonnes and grades were carried forward from the previous budget. The zinc concentrate grade target was fixed at 57 per cent Zn, a long-term average; it was the accepted æstandardÆ for Rosebery. Historical data showed this target was never consistently achieved and plant efficiency was highly variable.Investigations into the possible causes for the variable performance ruled out plant and mechanical issues. Despite the Rosebery concentratorÆs age the plant and equipment are more than serviceable and reliable. The mineralogy of the ore and specifically the iron content of the sphalerite was found to be the most significant determinant of zinc concentrate grade. It was found with increasing frequency that the zinc grade of the sphalerite in the ore was below the zinc concentrate grade target. Consequently on these occasions attempts to meet the required concentrate target destabilised the process resulting in plant inefficiencies.Using the correlation between iron and zinc, data modelling was able to accurately predict the maximum zinc concentrate grade achievable for any ore type. By using on stream analysis instrumentation the operations personnel are now provided with constantly updated concentrate grade targets. By knowing the mineralogical limits of the ore at the time it is being treated process stability is maintained allowing plant efficiency to be optimised. This has resulted in a step change in plant performance and a significant increase in revenue.CITATION:Harris, G R, 2012. Developing and implementing ore-specific targets for the Rosebery Concentrator, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 321-324 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Mez W

the German ruining industry uses different residues for hackfilling and stowing. A hydraulic pipe conveying technology for these materials has shown advantages for the transportation into the mine. Pipeline conveying systems are able to bridge long distances, they save room within the underground workings and they save staff and costs. Absolutely necessary for successful use of the hydraulic conveying technology is the knowledge about the unusual non-Newtonian flow properties of solid/liquid mixtures like pastes and slurries. The flow resistance of these materials cannot be described easily by one viscosity. Owing to a yield point and a pseudo-plastic behaviour the viscosity changes with the shear rate and with the streaming velocity inside the pipe. Also these flow behaviours depend very sensitively on the liquid/solid-ratio, often so dramatically that gravimetric or volumetric dosing equipment is not in a position to control the production of backfill pastes. Quality changes of the solid raw materials (particle size distribution, density, mineralogical composition) lead to additional difficulties. The first experiences with hydraulic backfilling plants were troubled by plugged pipes. a bad backfill quality caused by unnecessarily high water content and high costs for chemical binders to solidify the backfill. The installation of viscosity controlled paste production leads to success with the hydraulic backfill technology. A development of the l)MT, a bypass pipe-viscometer, has been the key technology. The system is able to analyse on-line, difficult, sticky and abrasive substances and determine their non-Newtonian flow properties. Because the system measures real physical values it is in a position to pre-calculate process relevant parameters like the pressure drop of the backfilling paste in the conveying pipeline. Newer types of the viscometer system also measure the slurry density and calculate its composition. These systems have proven a success controlling backfill paste production plants. They offer it secure prevention of pipeline plugging and a production of high quality backfill pastes with a water content as low as possible.

Jan 1, 1998

By Z-Y Pi, B Zhang, S Wen

"The paper introduces the structure and work processes of outside auger hollow claw tipped mechanical sampler for coal. Twenty sets of claw tipped sampler performance tests show that: The design of inner hollow cylinder-type (?180 mm) can ensure to take a coal sample with nominal top size of 60 mm. Built-in self-cleaning piston pusher ensures no adherence and blocking of the sample. The operation practices show that the mechanical sampler can operate in order for taking coal sample with up to 16 per cent of total moisture. Claw closing design can avoid sample leaking or spilling during the claw lifting and ensure the integrity of primary increment. Ultrasonic positioning device makes the sampler capture the materials no less than 10 cm from the bottom of the wagons, basically meeting the requirement taking full depth of the sample. The precision and bias test indicates that the moisture and ash have no relative bias under the sampling process; the sampling precision is in accordance with the requirement in IS013909.At present, the spiral mechanical sampler is widely used for coal sampling but there are many limitations during application, for example: It is difficult to capture a large size sample, so the size range of a coal sample taken is limited. There is easy adhering or blocking for high moisture coal, which will result in the mixture of different increments, wear of sampler and the difficulties for cleaning and maintenance of sampler. It is difficult to capture the coal sample at lower than 30 cm from the bottom of the wagons, in order to avoid damage of the vehicle. It is possible for coal sample loss and spilling during the sampler lifting, due to the unsealed sampler.For the outside auger hollow claw tipped mechanical sampler designed for solving the above problems, the opening distance of the claw is the opening size of the sampler and makes the size range of the coal sample to be taken wide. During sampling, the two pieces of claws open and the sampler rotates vertically downward to capture an adequate coal sample after reaching the specific point. Then the two pieces of claws close tight automatically to ensure there is no coal leaking or spilling. The inner pusher of the sampler will prevent from the adherence and blocking of the coal sample effectively.CITATION:Zhang, B, Pi, Z-Y and Wen, S, 2012. Outside auger hollow claw tipped mechanical sampler for coal, in Proceedings Sampling 2012, pp 41-44 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

By K Knorr

Desktop X-ray powder diffraction using a D2 PHASER equipped with fast linear detector was performed on several iron ore and mill scale samples. Data were analysed using cluster analysis and Rietveld quantitative phase analysis. The quantitative mineralogy of both materials could be established. Thus the input is provided for understanding the energy consumption and the CO2 emission during iron production. Furthermore, tabletop XRD allows to distinguish iron ore from mill scales and to quantify their mixtures.

Jul 11, 2011