Search Documents

By W. A. Clark, E. H. Dresser

ORE from the Minnesota iron ranges is transported from the mines to the loading docks on Lake Superior over four different railways: the Great Northern, Northern Pacific, Soo Line, and Duluth, Missabe and Iron Range, with hauls varying from 60 to 110 miles. For this service a large amount of specialized equipment is used. The steel ore cars are of the hopper type, 24 ft. long, to dump into alternate pockets of the docks, these pockets being 12 ft. long to correspond with the 12 or 24-ft. spacing of the boat hatches. The more recently con-

Jan 1, 1941

By T. T. Read

TWO papers on health and safety were given Thursday afternoon when a joint session of the Health and Safety Committee and the Mining Methods Committee was held. T. T. Read presided and the first paper, on ventilation at Climax, was presented by the author, L. H. Glanville. In the subsequent discussion by Cloyd M. Smith, P. B. Bucky, B. F. Tillson, D. F. Haley, J. L. G. Weysser, and others a number of interesting points not covered by the paper, which appears in full in the January Mining Technology, were brought out. Ventilation troubles in mines so often hinge on the air being too hot and damp that it was interesting to hear of one where it is frequently too cold and too dry.

Jan 1, 1943

By ERNEST W. ELLIS

MORE or less contradictory findings as to the most satisfactory feed for concentration tables of the Wilfley type is shown by the diversity of opinion among experimenters. Prof. R. H. Richards,l as a result of his work, favors classification. On the other hand the work of Messrs. Cox, Gibbins, and Porter,' of McGill University, points in general to the desirability of screen-sized feed The ore used was obtained from the West mill of the Bunker Hill and Sullivan Mining and Concentrating Co., Kellogg, Idaho, and consisted of argentiferous galena in a gangue of quartzite and siderite. The natural feed was taken from the launder supplying the Fahrenwald classifier. Classified feed was collected from each of the ten spigots of this same classifier. From the natural feed the screen-sized feed was pre- pared in the laboratory. All three types of table feed were therefore derived from the actual mill circuit of a large plant.

Jan 1, 1926

By Carl Lee

WITH the modern trend toward motor drive in coal mines, more careful forethought should be given to future layouts than has usually been done in the past. Both top and bottom equipment of future new mines is likely to differ radically from those of a decade ago. No one is able to predict very far ahead, but provisions can be made to allow for uncertainty. One thing stands out: the mine of the future will be laid out for long life compared to that of the small mine of the past, where an inexpensive top plant, simple equipment, a small timbered shaft, small cars, light rail, hand loading and mule haulage all contributed to a short economical life.

Jan 1, 1933

By Eugene McAuliffe

NO physical impairment can be more serious than the partial or complete loss of sight. With reasonably good eyesight, a person is equipped to care for life and I limb, provided a rational measure of t caution is manifested. When the sight of one eye is lost or badly impaired, one-half of this God-given asset is gone, and extreme care must be taken to prevent the tragedy of total darkness that closes out the beauty of sky, field and mountain, the faces of relatives and friends, and either removes entirely or in part one's capacity to produce and earn. During 1933, The Union Pacific Coal Co., operating ten coal mines in Wyoming, decided to undertake a visual survey of all of its mine operating officials and employees. Although the cost of workmen's compensation paid because of eye injuries was material, the management was more deeply concerned with the social loss and the suffering resulting from the many eye injuries. As every element of coal production cost must be scrutinized, accurate data on all accidents, with the workmen's compensation paid therefor, are carried forward monthly. The number of accidents to eyesight and the resultant compensation paid are shown in Table 1 for nine calendar years:

Jan 1, 1934

By AIME AIME

OUR own Institute of Metals and Iron and Steel divisions cooperated with the Iron and Steel Division of the American Society of Mechanical Engineers, the American Welding Society, and the American Society for Steel Treating in a busy week at Cleveland. The morning sessions were held at the Hotel Cleveland and the afternoon ones at the Auditorium, where the metallurgical exhibition under the auspices of the American Society for Steel Treating not only occupied the arena of the Auditorium but completely filled the huge adjacent Annex. In the intervals of sessions the members thronged the exhibits but in the evenings the local attendance was so great that if the crowds had been any larger it would have been difficult to see the exhibits. With so many firms, both producers of metals and of equipment accessory to their production and use, it would be impossible to mention them -all and unfair to single out a few, since no two individuals' judgment would coincide as to relative interest and importance. In any case an exhibit is a thing to be seen rather than described, and these were well worth seeing.

Jan 1, 1929

By G. D. TRANT

HOT metal is commonly transported from the blast furnace to the open hearth by one or the other of two general methods: (1) by hot-metal ladles, usually in conjunction with a stationary mixer, or; (2) by means of mixer-type ladle cars, taking the place of both the hot-metal ladles and the stationary mixer. In both cases, the use of transfer ladles for charging the metal into the open-hearth furnaces is necessary. The American Rolling Mill Co. at its Middletown division, adopted hot metal practice on. June 2, 1928. The pig iron is produced' in a .blast furnace about 11 miles from the open-hearth furnaces, and is trans- ported in Pugh-type mixer cars having a capacity of 150 gross tons each. Three cars are in service and handle the delivery of hot metal to the pig machine and the open-hearth furnaces. The capacity of the blast furnace is 550 tons and casts are made every four hours.

Jan 1, 1929

By W. H. Bassett

BERYLLIUM was discovered in 1798 by Vauquelin and the metal was first produced by Wohler in 1828 about a year later than his production of metallic aluminum. Beryllium remained dormant until about 1920 when the production of the metal by the electrolysis of a molten bath was carried out by Stock in Germany, closely followed by Dickinson in the United States and by Vivian in England. This may not have been the first time the electrolytic method was thus used but was the beginning of present-day methods. I believe the first commercial attempts in this country started with the Kemet Laboratories about 1924. Siemens & Halske in Germany were working on the same problem at about the same time. The work of the Kemet Laboratories was transferred to the Beryllium Company of America and later to the Beryllium Development Corporation. In 1926 1 made a considerable study of the beryllium¬copper alloys, using beryllium purchased from the Beryllium Company of America, and read a paper on this subject at the February, 1927, meeting of the A.I.M.E. However, I failed at that time to discover the properties of precipitation hardening which such alloys have in a very marked degree. After this publication the work on beryllium-copper alloys rested awhile. One cause for this was the difficulty of securing a supply of beryllium-at least at what might be considered a reasonable price. In 1926 the price was $200 per lb., a figure which held about the same both in this country and in Germany until the beginning of 1932, when it was offered here at $50 per lb. if taken in the form of a copper alloy which carried about 121/2 per cent beryllium. Somewhat later the 121/2 per cent alloy dropped to $25 per lb. of beryllium contained, which is the present price. Promise is made that with a greater consumption, production on a larger scale warrants a reduction in price to $10 per pound or less.

Jan 1, 1933

By W. J. Millard

VAGUE rumors and stories have been heard, from time to time, about the diamond and gold deposits of southern Venezuela. It is perhaps appropriate, at this time of revived interest in gold mining, to publish a few facts in regard to this country, which has been undergoing exploration since the fifteenth century. Gold and diamonds are found principally in the State of Bolivar which lies in southeastern Venezuela and is bounded by British Guiana on the east and Brazil on the south (see Fig. 1). The famous Mt. Roraima is situated at a point where these three countries meet in a common point (see Fig. 2). Some gold is also found in the southern part of the territory of Amacuro. Good oil prospects exist in the northern part of this same territory. Diamonds are found on the Caroni river from Rio Paragua to the village of Guri. Another small district is on the headwaters of the Cuyuni river. Quartz veins containing gold are chiefly exploited in

Jan 1, 1931

By AIME AIME

IN many countries the lack of liquid petroleum supplies has centered interest upon the hydrogenation of coal and coal tars for the preparation of motor fuel. In the United States, hydrogenation has been of greater interest for grading up low-value petroleum fractions to the more valuable volatile fuels and for the preparation of a variety of premium products, including aviation gasolines, solvents, Diesel fuels, and lubricating oils. Chemically, the basic reason for this process is that, as shown in Table 1, the ratio of hydrogen to carbon (H/C ratio) in available raw materials is quite different from that characterizing the products sought.

Jan 1, 1936

By AIME AIME

THE petroleum economics session," held on Wednesday morning, Feb. 20, 1929, presided over by Campbell Osborn, chairman, proved to be of un- usual interest and resulted in serious and constructive discussion of the papers presented. The first paper on the program, "Gasoline Economics and Refinery Operation," was by H. J. Struth, petroleum economist of the Gulf Publishing Co., Houston, Tex. While this paper was intended to cover the re- finery situation, it also presented the author's reasons for believing that the oil producer should give cognizance to gasoline demand as a most reliable barometer by which to parallel the production of crude petroleum. The discussion which followed brought out some interesting points in connection with the immediate outlook for the industry as a whole during the present year. Some advanced the opinion that, regardless of the out- come of proration efforts, the refiner is in a position to conduct his operations on a reasonably profitable basis, provided that he exercises control over them. This would mean running less crude and resorting to wider utilization of cracking to produce the gasoline demand. Thus, if the refiner uses diligent care in scheduling his still runs, the producer will be obliged to carry over a large stock of crude this year, unless he is able to keep production below the limits prescribed by the demand for gasoline.

Jan 1, 1929

By AIME AIME

THE initial meeting on Mining Methods* opened at 10 o'clock Monday morning with Scott Turner as chairman and W. Spencer Hutchinson as vice- chairman; about 60 attending. After preliminary announcements Theodore Marvin was called on for his paper,, entitled "Rock Tunnel Methods," which has been appearing serially in The Explosives Engineer. Marvin read the introduction and called attention to the account of one or' two particularly' interesting projects, such as the. Brooklyn water supply tunnel. E. D. 'Gardner, Char1e.s S. Hurter, L. D. Lamont and Spencer P. Howell took part in the discussion, Howell commenting on the fact that, in one case cited, misfires had occurred through detonator wires 'coming in contact with the case of an unapproved flashlight, .,: and that all flashlights should be approved.

Jan 1, 1931

By Arthur A. Center

AT the beginning of 1944 it was expected that the production of metallic zinc in the United States from domestic and foreign concentrates would exceed the 1943 figure though domestic production of concentrates was expected to drop below the 1943 rate, mostly in the Tri-State area. Imports of concentrates were estimated to more than take care of such deficiency. North American concentrate production, available for import to the United States or elsewhere during the year, was estimated at over 200,000 tons recoverable zinc content; South American at about 65,000 tons; Australian at about 50,000 tons. Production of both concentrates and metal in the United States, however, did drop, attributable in considerable part to man-power shortage in the industry. However production exceeded consumption, which fell off, and stocks of metal increased. These stocks have increased since the middle of 1942 but production and consumption are coming nearer to a balance. The A, B, and C premiums, which have played an important part in keeping up domestic production of concentrates, extend only to the middle of 1945 by present legislation. Congress is being asked for their continuance during the war and

Jan 1, 1945

By A. J. Weinig

IN the accompanying figure consider the classified AB in closed circuit with a ball mill, wherein T = Tonnage of new feed C = Ratio of circulating load Now consider that the circulating load is made up of two portions of ore. One portion is due entirely to the characteristics of the ball mill and the tonnage of new feed impressed on the ball mill. This portion of the circulating load in no way is to be blamed on the characteristics of the classifier and is all composed of oversize. Consider, for illustration, that this portion of the circulating load is handled in the A division of the classifier, assuming that the classifier is divided longitudinally into two divisions by an imaginary line. Because the classifier does not usually make a perfect separation of the undersize, a certain portion of the total circulating load is to be directly blamed on the efficiency of the classifier. Let this portion of the circulating load be considered as being handled in the B division of the classifier. Now if the classifier is operating perfectly (100 per cent efficient), the width due to the B division becomes zero and correspondingly the efficiency of the classifier diminishes as B becomes wider in proportion to A. If E is the mechanical efficiency, then

Jan 1, 1934

By G. B. Sazuyer

DEVELOPMENTS respecting beryllium during the past year have been sufficient to center attention on it as likely to be the most important of any of the chemical elements that have recently found a place for themselves in technical industry. This importance is only potential, however, largely because adequate supplies of beryllium ore will be necessary. The beryllium industry will be only as great as the mines which support it. To find and develop large mines will be the problem. Chief of the immediate commercial developments in the United States is beryllium-copper and its espousal by Anaconda and Riverside even at present high prices. According to the pamphlets of these companies, it ap¬pears that beryllium is to copper nearly what carbon is to iron. When one considers that the tensile strength of pure copper is about 33,000 lb. per sq. in., but that the addition of 1.5 to 2.5 per cent of beryllium produces a heat-treatable alloy with a maximum tensile strength of 220,000 lb. or over, the analogy to carbon and iron is made strikingly, clear. Striking among the properties of beryllium-copper is its resistance to fatigue, claimed to be equal or superior to that of spring steel. It needs little imagination to foresee a great industry for this alloy alone.

Jan 1, 1934

By Robert L. Dean

THE pioneer mining company in Idaho to use airplanes extensively is the Yellow Pine project at Stibnite now owned by the Bradley interests. From 1901 to 1903 the gold boom at Thunder Mountain, in central Idaho overflowed to adjacent areas, prospectors discovering cinnabar and stibnite near the present site of Stibnite in Valley County. The workings were practically abandoned by 1911 through lack of capital and high costs of transportation on pack train roads over several mountain passes open only five months each year. During the World War there was some prospecting and production, and in 1921 twelve of the original companies were merged. Small-scale mining up to 1927 proved that an expenditure of several million dollars would be necessary to operate profitably. These properties were purchased by the Bradley interests during the period of 1927 to 1930. In 1927, there was no mining equipment except hand tools, no telephones, and only one building. Two mountain

Jan 1, 1935

By Jay A. Carpenter

THIS preliminary report from the Committee to Study Relations Between Students and the Institute is submitted to our member- ship for consideration and discussion before the general subject comes up for action at the Annual Meeting in February. At present, the A. I. M. E. has a dual relationship with mining students, each relationship in no may connected with the other. To the individual student the Institute offers for $2 a year a Student Associateship in the Institute which carries with it a subscription to MINING AND METAL- 'LURGY, a watch fob, and the privilege of becoming a Junior Member after graduation without payment of the -first year's dues, if one's application is accepted. To the student's college society it offers the privilege, upon application, of becoming 'an Affiliated 'Society, which brings with it no specific supervision or aid, and in turn requires no specific conditions as to membership, fees, or rules. This Affiliated Society is distinctly a school organization which Student Associateship in the Institute can he given special status or ignored, is the local .society sees fit.

Jan 1, 1934

By AIME AIME

NO FEATURE of the annual meeting is considered more important at Institute headquarters than the assembly of delegates from the various local sections and divisions. There the president of the Institute and other officials may learn at first hand what the members are thinking and doing in every part of the country, and the delegates, in turn, may find that head- quarters is not a group of more or less cold-blooded New Yorkers whose primary function is to send out annual bills for $15. This year, the section and division delegates required three sessions to thresh out the matters of common interest: Monday morning and afternoon and Thursday afternoon. They were also guests of the Institute at the Directors' dinner on Tuesday night, and at the Directors' meeting afterward.

Jan 1, 1932

By AIME AIME

FOR the development of a mine, a shaft of small cross-section is usually sunk, of no larger size than is absolutely necessary. After the mine has been developed and put on a production basis it is a common practice to sink a shaft of larger cross-section for hoisting and use the original shaft for the handling of men and material into the mine. While that ar¬rangement is usually expedient, the small size of the supply cages presents a problem in the handling of ma¬terial. Where a cage is, say, 4 by 4 ft., which is not an uncommon size, all lengthy and bulky material must be handled piece by piece several times from the supply department to the underground stations. Thus drill steel and timbers over 4 ft. long will be loaded on cars at the supply department and wheeled to the shaft, where each piece must be unloaded from the cars and stood up in the cage. They are then lowered to the shaft station, unloaded piece by piece and placed in cars, run to the supply station and again unloaded and stored until called for. In such a case handling becomes a major item in the cost of supplies.

Jan 1, 1930

By Frederick T. Williams

THE purpose of this paper is to discuss the relative merits of the large 31/8 in. machine and the small 21/4-in. tappett machine in driving development-headings ; and although the . data here presented were obtained from cross-cut headings alone, experience has shown that the results are equally true in drifting, raising and winning. Recently we drove two parallel cross-cuts through the same formation, using a 3k-in. machine at the breast of one cross-cut., and a 2k-in. machine of the same make at the breast of the other. The results of this work afforded an ideal comparison, since in both cases the headings were advanced through rock practically of the same hardness and breaking-properties ; the amount of sludging was equal, and there was no difference in the condition of the steel or the machines, in the air-pressure or in the experience of the operating-crews. Some operators in the Cripple Creek district contend that there is ground which cannot be handled with the small machine, the holes being too small to contain enough powder to pull the ground, etc. The results obtained in working the property of the Portland Gold Mining Co., however, show that the ground worked by them does not fall in this class. During a period of two years there have been driven, with the small machine, 4 miles and 308 ft. of development-headings, through a diversity of ground, including Pike's Peak granite (a coarsely porphyritic type of granite), highly indurated, andesitic or phonolytic breccia, true massive andesite, trachytic phonolyte, tuffas, and along dikes of decomposed basalt and hard phonolyte; in every instance a satisfactory record was made. The headings here described were driven through highly indurated, andesitic breccia, having a hardness of from 5.2 to 7.2

Mar 1, 1906