Search Documents

By Ming-Kao Yen

A considerable amount of work has been reported in the literature in regard to the texture and earing behavior of copper strip. The rolling texture of copper has been confirmed as (110) [112] and (112) [111], which yields ears of a drawn cup at the position 45" from the rolling direction.1-3 The recrystallization texture has been established as the cubic or (100) [001] texture, where the earing positions are at 0" and 90" to the rolling direction.4-8 It has also been reported that in the development of cubically aligned grains of copper strips, the percentage of this cubic texture increased with an increase of final reduction and final annealing temperature.8,9 A comprehensive study on H.C. copper (British commercial copper of high-conductivity quality = Cu 99.95 pct, O2 0.03 pct, Ag 0.003 pct, Fe 0.005 pct and Pb < 0.001 pct) was made by Cook and Richards.6 They concluded that the recrystallization textures could be described as one or more of the following textures: (1) a single texture (100) 10011, (2) a twin texture (110) [112] and (3) a random orientation, depending upon the previous history of the specimen concerned. The effect of various alloying additions in copper was reported by Dahl and Pawlek.10 They found that certain alloying additions, such as 5 pct Zn, 1 pct Sn, 4 pct Al, 0.5 pct Be, 0.5 pct Cd, or 0.05 pct P suppressed the formation of cubic texture. Brick, Martin and Angierll reported that the cold rolled textures due to various additions fitted a rather simple pattern. However, the recrystallization textures were subject to very considerable variations. In the discussion of this paper, Baldwin stated that deoxidized copper containing 0.02 pct P gave a complicated recrystallization texture at lower temperature. When this copper was annealed at high temperature, a single texture appeared which was described as (110) [ill] but. according to a pri- vate communication from Baldwin, this orientation reported was in error and should have been reported as (110)[112]. He also reported that the earing positions of drawn cups were at 60" to the rolling direction.12 Recently, Howald, in his discussion on the paper by Hibbard and Yen,13 reported that the rolling texture of phosphorus deoxidized copper, containing from 0.006 to 0.020 pct phosphorus, was of the pure copper type. When these coppers were annealed at lower temperatures, they exhibited a random orientation, and when they were annealed at higher temperatures they had a mixed (111)[110] and (100)[001] texture, depending on the severity of the final reduction and annealing temperature. However, the specific influence of phosphorus and other impurities on the recrystallization textures and the deep drawing properties of copper strip has not been thoroughly reported. Therefore, an attempt has been made in the present work to determine the rolling and recrystallization textures and also the earing behavior of five types of commercial copper and thereby to evaluate the effect of phosphorus and some other significant impurities on the development of texture for cold reductions of about 87 to 89 pct. Materials Used The five types of copper employed in the present investigation were two phosphorus deoxidized coppers of different phosphorus content (0.007 and 0.013 pct P), an oxygen-free copper (OFHC), an electrolytic tough-pitch copper, and a fire-refined tough-pitch copper. These materials were subjected to a thorough spectroscopic and chemical analysis. The designations and the chemical compositions were as shown in Table 1. The coppers, FA1, FA2 and FA3. were hot-forged from 3-in. billets into a ½ X 6-in. plate and cold rolled to the ready-to-finish gauge indicated below. FA4 and FA5 were hot rolled and scalped to ready-to-finish gauge. The grain size of all the materials in the ready-to-finish condition was about 0.030 to 0.045 mm. Table 2 shows the last stage of the production schedule for each copper strip used. Experimental Procedure ANNEALING, GRAIN SIZE AND HARDNESS DETERMINATIONS Specimens of each type of copper were finally annealed in air for periods of one hour at temperatures ranging from 300 to 1600°F and were subsequently cooled in air. The average grain diameter of the annealed specimen was estimated by comparing with a standard grain size chart. Hardness was determined on the Rockwell 15 T scale. CUPPING TESTS Cups were made in a blanking and drawing set, in which blanks of 2-in. diam were drawn to a cup of 1.25-in. diam with an average depth of about 0.75 in. The clearance between the punch and die was about 0.032 in. The ears of the cup were measured with a special fixture which read the height of ears to one-thousandth of an inch on every ten-degree interval along the circumference of the cup. POLE FIGURES The usual transmission diffraction method with unfiltered copper radiation was employed to determine the pole-figures of the specimens cold-rolled or annealed at 900°F. All the pole-figures were derived from the positions of intensity maxima on 111 diffraction rings of the X ray photo-grams taken at 10 rotation of a

Jan 1, 1950

By L. Leibowitz, M. G. Chasanov, L. W. Mishler

A drop calorimeter system is described for use in measuring enthalpies to 3600°K. Data are presented for tungsten between 2800" and 3600°K. The enthalpy of tungsten in cal per mole between 2000° and 3600°K can be represented by the equation HºT- Hº298 = - 1.7622 X 103 + 5.7772T + 8.9861 where T is in degrees Kelvin. A tabulation of com -puted values is presented for heat capacity, entropy, and free energy function. A drop calorimeter has been constructed to carry out enthalpy measurements at temperatures to 3600°K. Samples are heated by induction1 and dropped into a commercial adiabatic calorimeter, modified for this purpose. The experimental temperature is limited by the melting point of container materials and compatibility of the container and its contents. Several high-temperature drop calorimeters have been described in the literature1-5 but none has been used at temperatures as high as those in the present work; our measurements of the enthalpy of tungsten range from 2800" to 3600°K. DESCRIPTION OF EQUIPMENT An overall schematic view of the equipment is shown in Fig. 1. Power for the induction coil is supplied by a 25-kw 250 kHz Ther-Monic generator coupled to an iron core RF transformer. The Sample capsule is suspended in the work coil by 10-mil diam tungsten wires which are wrapped around a horizontal 5-mil diam tungsten wire. The horizontal suspension wire is clamped between two massive copper electrodes which are fixed in an x-y motion device that allows adjustment of the position of the heated capsule from outside the vacuum chamber. The copper electrodes are connected by flexible copper straps to a 1250-joule (5 kv, 100 pfarad) condenser bank. When it is desired to release the capsule, the condensers are discharged through the horizontal suspension wire causing it to vaporize rapidly. Very reliable and precise release of the capsule is achieved in this manner. Experiments have shown that no heat correction is required for this discharge energy. As part of the temperature measuring system, two prism holders have been incorporated in the apparatus. The upper prism holder is in the main vacuum chamber itself, whereas the lower one is in a side arm attached to the drop tube below the gate valve. The upper prism is mounted on a rotary vacuum feed-through, and may be moved under a protective shield when not in use. This prevents deposition of vapors on the prism surfaces when temperature measurements are not being made. Similarly, the lower prism is mounted on a push-pull vacuum feed-through, and when not in use may be pulled into its side tube. The prism mountings are fitted with guides and stops so that they may be moved precisely into the desired position. The aim throughout is to minimize the time the prisms are exposed to vapors from the hot samples. At the high temperatures reported in this paper, only the lower prism was used. The upper prism holder in these cases was fitted with an additional radiation shield. By using a prism and viewport, the lower surface of the samples can be observed by an optical pyrometer. The measurements discussed in this paper were obtained with a Leeds and Northrup 8622-C-S series manual pyrometer which is estimated to be accurate to 0.5 pct. Pyrometer calibrations and prism and window corrections were carried out in the conventional manner6 using tungsten strip lamps calibrated by the National Physical Laboratory, Teddington, England. Prism corrections were rechecked after each use. All work to date has been done in vacuum, and no measurable change has been observed in the prism correction below -2300°K for the upper prism and below -2800°K for the lower one. The total time of exposure of the prisms is about 50 sec per run. At high temperature, the final temperature reading is corrected by using the final A value for the prism; see Ref. 6 for details of this procedure. The calorimeter is a modified Parr Instrument Co. (Moline, lll.), Series 1230 adiabatic calorimeter with automatic jacket control. Other authors5 have used a similar calorimeter with good results. The calorimeter jacket cover and calorimeter cover are attached to the drop tube which contains a radiation shield. This shield is a gold-plated copper disc which can be operated manually from outside the calorimeter. The receiver is attached below the radiation shield and is lined with tungsten. In a typical experiment, the calorimeter and its jacket water temperatures were adjusted to 0.000°K temperature difference. The sample was allowed to equilibrate in the furnace at the desired temperature for about 20 min. The initial calorimeter temperature was then recorded, the sample dropped, and appropriate shutters closed. After about 3 min, the drop tube and receiver were filled with helium to 60 torr. The final calorimeter temperature was recorded after it had remained constant over a 5-min period. The equilibration time in the calorimeter was about 25 min. Thermistor probes are used to operate a hot and cold water supply system to maintain the jacket temperature equal to the calorimeter temperature. For actual measurements of the calorimeter temperatures, a quartz thermometer was used (Hewlett Packard Dymec Thermometer, Model #2801A). This thermome-

Jan 1, 1970

By Craig S. Hartley

An approximate expression is obtained for the energy of a closed dislocation loop in equi1ibriu)n with a constant net stress. The result obtained is valid for loops in isotropic or anisotropzc materials provided that they are suJficiently large that the energy per unit length of a segment of the loop can be approximated by that of an infinite straight dislocation tangent to the loop. It is shown that this approximation leads to very close agreement with a more rigorous calculation of the elastic energy of a circular glide loop. The Gibbs-Wulff Form, GWF, of a dislocation is the closed planar loop which has the smallest elastic self-energy of all possible loops having the same Burgers vector and enclosing a fixed area, A.&apos; The energy of such a loop is related to the net resolved shear stress* required to expand the loop and to the stress required to activate a Frank-Read source.223 In the following sectiorls the problem of determining the form of the GWF is discussed and an approximate method for calculating its elastic self-energy is presented. It is demonstrated that the approximations employed lead to no serious errors when applied to a calculation of the elastic energy of a circular glide loop. This method is then used to obtain a closed form expression for the energy of GWFs in isotropic and anisotropic materials. THEORY Burton, Frank, and cabrera4 have proved that the relationship of the equilibrium shape of a two-dimensional array of atoms under the influence of the Gibbs free energy associated with unit length of its boundary, G(O), is that the polar plot of G(0) vs 0 is proportional to the pedal of the GWF.* The angle 0 is measured "The pedal of the polar graph ofG(0) vs0 is the envelope of tangents to the eraph.relative to some crystallographic reference direction. The difficulty in applying this result to a closed dislocation loop arises from the self-interaction of the loop. For a dislocation the energy analogous to G(0) is a function of the total configurati~n.~ Consequently the relation which determines the GWF is an integro-differential equation rather than the simple differen- tial equation which results when G(8) is a function of 0 alone. Mitchell and smialek3 and Brown~ have used the self-stress concept introduced by ~rown&apos; to calculate the shapes of dislocations in equilibrium with an applied stress. In this approach the glide force on an element of the dislocation loop due to the interaction of the element with the rest of the loop is equated to the glide force exerted by the local applied stress. The shape of the loop is then adjusted so that the two forces above are equal at all points on the loop. It is possible to calculate the energies of such loops by noting that, for equilibrium with an applied stress, the energy is equal to pijbiAj (summation convention) where bi is the Burgers vector, p.. is the local net stress tensor, and Ai is a vector directed perpendicular to the plane of thd loop with magnitude equal to the area of the loop. Also Brown&apos; has calculated the energy of a hypothetical polygonal GWF using the above technique and anisotropic elasticity. However, his indicated solution for the energy in the general case of an arbitrary GWF is only slightly less involved than an iterative solution of the integrodifferential equation referred to earlier. In the present work the approximation employed by DeWit and Koehler&apos; is used to calculate the energy of a closed loop in equilibrium with an applied stress. That is, the energy of a loop segment, ds, is approximated by the product of ds and the energy per unit length of an infinite, straight dislocation in a cylinder coaxial with the tangent to the loop at the angular position of the segment. This is known as the "line tension" approximation. The inner cutoff radius of the elastic solution defines the core radius, while the outer cutoff radius is determined by some characteristic dimension of the loop. Actually, both of these radii vary with the edge-screw character of the segment. The effective core radius changes because of the orientation dependence of the Peierls width of a dislocation,8 and the outer radius should be the radial distance from the circumference of the loop to the center of symmetry of the area enclosed by the loop.g However, since the energy varies logarithmically with the ratio of these radii while depending directly on the effective elastic constants, only the effect of the latter is considered. This approximation also neglects the self-interaction of the loop segments. For small loops this will doubtless be extremely important, but for large glide loops produced by plastic deformation the self-interaction is not nearly so important in determining the energy of the loop. This point is illustrated by the following calculation of the energy of a circular loop. Consider a circular loop of radius R which lies in the XI - x, plane of an infinite isotropic continuum and whose Burgers vector makes an angle $ with xs. The first-order solution for the elastic self-energy is:&apos;

Jan 1, 1970

By D. S. Gleason, D. E. Severson, D. R. Skidmore

Pittsburg and Midway Coal Co. has modified the German Pott-Broche process, on which patents date back to 1927, to produce on a bench scale liquid products by solution hydrogenation of coal. A continuing program of lignite solution-hydro gena-tion experiments is directed toward investigating coal solution reactions, determining favorable conditions for the solution refining of lignite by the Pott-Broche process, and investigating some of the uses for the de-ashed product obtained from lignite The German Pott-Broche process1" on which patents date back to 1927, has been modified by the Pittsburg and Midway Coal Co., a Gulf Oil subsidiary, to produce on a bench scale liquid products by solution -hydrogena-tion of coal." The objectives of the present effort are to investigate coal solution reactions, to determine favorable conditions for the solution refining of lignite by the Pott-Broche process, and to investigate some of the uses for the de-ashed product obtained from lignite. This paper is a summary of results to date in a continuing program of lignite solution-hydrogenation experiments. The coal solution reaction program has several principal aims. The first of these is to determine whether lignite can be successfully dissolved in solvents that might be practical for commercial development. The second object is to determine whether the solvents function after successive cycles of use, recovery, and reuse. It seems necessary to the economics of a potential commercial process that the solvent be recycled. Third, it is desired to learn something about the distribution of the ash constituents between cake and filtrate. The extent of ash removal is important. The nature and quantity of mineral matter passing through the filter may determine end-use marketability. For certain use applications, trace quantities of certain minerals can be objectionable, e.g., titanium and vanadium must be very low in electrode carbon for aluminum production. The Solution Reaction The coal solution Process involves an extremely complex system of chemical reactions. An initial solvent such as anthracene oil is a mixture of hundreds of different compounds with a boiling range of roughly 500" to 750°F at atmospheric pressure. The coal macro-molecule is broken down by thermal decomposition and solvent action into myriads of different compounds, some the same as those comprising the solvent. This similarity in structures opens up the possibility of production and subsequent recovery of solvent. Some solvent is inevitably lost by reaction. Regeneration of solvent was not a problem in the early German Pott-Broche plant. The coal refinery was an integral part of a petroleum refinery complex and replacement solvent was readily available. A coal refinery using lignite, however, might be isolated from other hydrocarbon processing facilities and the regenerability of solvent could be vital to the economic success of the venture. Several structural features of the solvent molecules have been cited as important to the coal solution process.&apos;. The first of these is aromaticity of the material, the second, ability to transfer hydrogen to another molecule, as for example the ability of tetralin to transfer hydrogen and be converted to naphthalene. Finally, the presence of hydroxyl groups on aromatic rings within the molecule, i.e., phenolic character, seems beneficial. Mixtures of pure compounds have been tried by various investigators. Mixtures of o-cresol, a phenolic substance, and tetralin were found to dissolve bituminous coal better than either substance alone.3 This maximum solubility was not found with lignite." Hydrogen contributes to the reaction by hydro-genolysis and by combining with free radicals and molecular "loose ends" to stabilize the compounds formed in coal depolymerization. High boiling point, and correspondingly high molecular weight, seems to be a property which improves solution potential for coal with a given type of compound.&apos; The maceral components of the coal appear to have an important bearing on its ease of solution. The fusain portion is quite inert to solvent action, but the an-thraxylon material dissolves quite readily.3 The hydrogenation reaction can be improved by the use of a catalyst; commercial hydrogenation catalysts having been found effective. Although cost is involved in the use of catalyst and catalyst recovery, the resulting saving in time and perhaps lowered temperature or pressure might justify their use in the solution refining process and decrease the total process costs. Apparatus and Procedure The coal solution runs were made in a 1-gal stainless steel stirred autoclave. The autoclave was provided with thermocouple wells and a transducer to permit continuous recording of temperature and pressure. The autoclave stirrer was magnetically driven, eliminating the leakage inherent with a rotating pressure seal. For runs in which a catalyst was used, the catalyst in the form of beads was placed in a wire mesh container mounted on the stirrer shaft. A control system programmed the heatup and reaction cycle. The permissible heating rate was 5°F per min because of the need to minimize thermal stress in the autoclave body. The temperature was raised at that rate until the reaction temperature was attained and then the temperature was held constant for the desired length of time. The maximum temperature seldom exceeded the average run temperature by more than 15°F.

Jan 1, 1971

By C. S. Sivaramakrishnan, Manjit Singh, Rajendra Kumar

Regarding liquid nzetals structurally as a suspm-sion of clusters , having derivated solid-state coordination, in truly liquid atoms, the recently developed Kuvlar-Samarin technique of centrifuging- in liquid state enabled the determination of the cluster sizes inAl-Cu mid Pb-Sn systems. It is shown that the colutne fraction of the clusters does not exceed 9 pct and the energy of their formation in Al-Cu is about 5.5 kcal per g-atom and in Pb-Sn eutectic alloys about 25 kcal per y-atoni. STRUCTURAL investigations of liquid state have principally followed the following three courses: i) studies with X-ray, electron, or neutron diffraction; these investigations have shown that there is a certain amount of regularity in the structure of liquid metals which can be defined by a coordination number and that the structure is a derived function of that in the solid state; ii) thermodynamical investigations which are based on the concept of ideal behavior; these describe the liquid state in terms of free-energy values and other thermodynamic functions; although these investigations are of help in the study of the general effects of alloying, they do not provide any structural insight into the precise atomic distribution in liquid state; iii) measurements of surface tension and viscosity; although it is natural to expect that the viscosity is related to the structure in liquid state, these investigations have so far only provided information which can be used by the foundry technologists and has been little utilized in formulating models of the structure of liquid state. As it happens, investigators in the three groups have worked almost independently of each other and there is practically no structural correlation between the results of one group with those of another. The purpose of the present paper is to indicate that the experimentally measured parameters of these three groups of research are closely related to the structure in the liquid state. STRUCTURE OF LIQUID METALS Although atomic distribution in solid and gaseous states is rigorously known, that of the liquid state is only appreciated on the fringes. There is no universal model of atomic distribution in liquid state, but two diverse models are at present hotly contested. The first, largely expounded by ~ildebrand,&apos; regards the liquids as condensed gas since many of their properties and much of their behavior can be adequately described by regarding them as fluids. The second mode12j3 considers that some form of near-solid as- sociation of large number of atoms exists in the liquid state. On the other hand, ~ernal&apos; was able to predict rather precisely the radial distribution functions in liquids on the basis of statistical geometric approach which considered that liquids are "homogeneous, coherent, and essentially irregular assemblage of molecules containing no crystalline regions or holes large enough to admit another molecule". He introduced the concept of pseudonuclei in the otherwise random structure as aggregates of closely packed tetrahedra which gradually merge into irregularity and continually replace each other. To what extent the pseudonuclei can be regarded as regions of near-solid association is indefinite but Bernal suggested that the concept of pseudonuclei can be compromised with the latter model if the near-solid associations are regarded as extremely dense and not necessarily crystalline. The difficulty in projecting the structure of liquid metals arises because they exhibit duplicity of character as some of their properties are closer to those of crystalline solids and others to fluids. There is an increasing tendency to discuss the structure of liquid metals in terms of the second concept according to which the structure of liquid metals may be conceived as consisting of i) clusters of atoms where the aggregation is a close derivative of that in the crystalline state, ii) individual atoms which behave like true liquids in respect to degrees of freedom and iii) excess number of vacancies. It is noteworthy that the introduction of only 5 pct vacancies is sufficient to transform crystalline matter into the liquid state. At any instant of time thermodynamic equilibrium exists between i, ii, and iii, but the relative proportion of the clusters and random atoms is not known. That this is so can be appreciated by the fact that, when liquid metal is rapidly cooled, liquid state vacancies may condense in the form of dislocation loops and vacancies in excess of their equilibrium number in solid state. These dislocation loops have been observed in thin foils of aluminum prepared from rapid cooled aluminum. As temperature increases above melting point the number and volume fraction of clusters decrease but those of vacancies and random atoms increase. Clusters are transient in nature. In pure metals the cluster is an aggregation of the metal itself. In alloys, however, the nature of the cluster largely depends on the interaction between solvent and solute atoms. If the interaction between unlike atoms is greater than between like atoms: the clusters are then aggregates of unlike atoms. Examples of this kind of system are A1-Cu, Mg-Pb, and so forth, i.e., systems which exhibit negative departures from the Raoult&apos;s law. In systems where the interaction between unlike atoms is smaller than be-

Jan 1, 1968

By J. D. Livingston, H. E. Cline

The lamellar-dendritic transition in Sn-Pb alloys near the eutectic composition has been studied at high growth rates. Lamellar structures were found over a substantial range of tin-rich compositions, and this range extended to increasingly tin-rich concentrations as growth rate increased. These results are discussed in terms of stability and competitive-growth arguments. Various experimental and structural limitations to the rate of directional solidification are discussed. The rate of heat removal at the heat sink is the major experimental limitation. ReCENT interet1,2 in the use of fine composite structures produced by directional solidification of eutectic alloys makes it important to determine the range of composition and growth conditions that yield such microstructures. Because increasing growth velocities produce increasingly finer microstructures, it is particularly significant to determine the factors limiting the rate of solidification. Mollard and Flemings3 have shown that composite structures, free of primary dendrites, can be obtained in Sn-Pb alloys of off-eutectic composition. The composition range of composite structures was found to increase with increasing values of G/V, where G is the temperature gradient and V is the growth velocity. These results are in good quantitative agreement with an analysis of the stability of a planar eutectic interface.4 This analysis specifically predicts that over a small range of compositions stable lamellar structures will be obtained even for G/V = 0, hence, even at very high growth rates. The lamellar-dendritic transition in Sn-Pb alloys has also been analyzed with a model based on competitive growth between dendrites and the composite structure.576 This treatment, based on earlier work on organic eutetics,7 predicts that the composition range yielding composite structures in Sn-Pb will increase rapidly at high growth rates. An increase in the composition range of composite structures at high growth rates was recently observed in Cu-Pb alloys near the monotectic composition.8 In view of these results, and the predictions of the stability and competitivegrowth analyses, it was decided to study the lamellar-dendritic transition in Sn-Pb alloys at high growth rates. EXPERIMENTAL Using 99.999 pct pure materials, a series of Sn-Pb alloys were prepared containing 16.8 at. pct to 27.6 at. pct lead. (Eutectic composition is 26.1 at. pct Pb.) Ingots were extruded to 0.175 in. rod, and some rod was drawn to 0.070-in. wire. Directional solidification was accomplished in two different ways, Fig. 1. For growth rates up to 2 x 10-1 cm per sec, a 0.175 in. diam sample was placed in a graphite crucible 5 in. long with 0.250 in. OD and 0.035 in. walls. Samples were melted under flowing argon in a vertical, platinum-wound furnace, and solidified by driving the crucible downwards through a \ in. hole in a water-cooled copper toroid, Fig. l(a). An insulated chromel-alumel thermocouple was imbedded in the center of a representative sample, and moved with the sample during solidification. The local temperature is plotted against the distance travelled by the sample in Fig. 2. As the growth rate increased, the solid-liquid interface moved closer to the water-cooled toroid and the temperature gradient increased. At growth rates above 10-1&apos; cm per sec, heat was not removed fast enough and the sample moved into the toroid in the liquid state. The curve for V = 2 x 10-1 cm per sec shows a plateau caused by incomplete removal of latent heat from the interface, a problem which will be discussed later. To improve the heat removal, the toroid was cooled by nitrogen gas precooled in liquid nitrogen. This allowed successful solidification at rates up to 2 x 10-1cm per sec. Higher solidification rates required still more effective heat removal. Samples 0.070 in. in diam were placed in graphite tubes 0.125 in. in diam with 0.020 in. walls. Instead of cooling by sliding contact with a cooled toroid, these thinner samples were sprayed or directly immersed into water, Fig. l(b). After solidification, samples were stored in liquid nitrogen until they could be examined metallographic-ally. The surface was prepared with a diamond-knife microtome, followed by a light etch. The presence or absence of tin dendrites, Fig. 3, or lead dendrites, Fig. 4, was noted by optical microscopy, usually of a transverse section near the center of the sample. Replicas of the surface were prepared and examined in an electron microscope to resolve the fine lamellar structures, Fig. 5. The structures observed at various compositions and growth rates are summarized in Fig. 6. Composite structures were observed at increasingly cin-rich compositions as growth rate increased. This transition from dendritic to composite structure with increasing growth rate was also demonstrated by solidifying half a sample at a slow rate and then suddenly increasing the growth rate by lifting the furnace and quenching the sample with a water spray. A longitudinal section of this sample, Fig. 7, shows that the tin dendrites, which extended ahead of the slow-moving composite interface, were bypassed by the composite when the growth rate was increased. The range of composite structures at high growth rates was limited by the appearance of primary lead dendrites on the tin-rich side of the eutectic composition. Observation of representative longitudinal

Jan 1, 1970

By C. Dirksen

This study investigates whether oxygen consumption during segregated forward combustion may be affected by natural convection. Linear theory indicates that thermal instability occurs in a horizontal porous medium when the modified Rayleigh number N &apos;Ra exceeds a critical value of about 40. Most experimental results, including those described here, indicate this value to be about an order of magnitude smaller. N &apos;, is derived from "differential similarity" and the proper time scale factor is also obtained. The critical value of N&apos;ra for a horizontal, water-saturated porous medium at atmospheric pressure subjected to a uertical temperature gradient was found to be about 3.0. The ambiguity in the value of N&apos;R, arising when fluid properties cannot be assumed constant is indicated. Natural convection was observed for oblique systems below N &apos;Ra , while simultaneous horizontal flow did not affect N Racrit. The expected range of values for the various parameters pertaining to segregated forward combustion is indicated and the corresponding values of N &apos;Ra calculated. Only under very favorable conditions, such as high permeability, high pressure and low top temperature, can the critical value of N &apos;R, be exceeded. Thickness of the convection layer should not become too large, since the time required to obtain significant mixing is proportional to the square of the thickness. For an oblique combustion frant the conditions for significant mixing may be less strenuous. LNTRODUCTION Laboratory1,2 and field314 experiments have shown that a markedly upgraded oil can be produced by in situ forward combustion. Under certain conditions injected air may move through a high permeability, gas-saturated channel over the oil-saturated layer, while combustion takes place, exclusively, at the horizontal interface (Fig. 1). Such a channel may be a natural gas cap, or it may result from a forward combustion process in which injected air and combustion gases fingered through the top of the formation, causing a premature breakthrough at the production well. In this particular case of segregated forward combustion, the air stream moves parallel to the combustion front. Molecular diffusion and transverse mechanical dispersion will be insufficient to cause all the oxygen in the air stream to reach the combustion front. When the oxygen in the air stream is not completely consumed in the combustion process, it will reach the production well and create a serious fire hazard. In addition, the reduced efficiency may make the process economically unprofitable while also serious corrosion problems may be experienced in the production we11.3 This undesirable situation should, therefore, be prevented. However, in a situation as depicted in Fig. 1, an unstable temperature gradient exists in the gas phase. The combustion is taking place at the lower boundary at a nearly constant temperature that may be anywhere from 600 to 1,200F, depending on the conditions. The upper boundary of the gas phase is overlying, impermeable rock; its temperature might be around 100F, but may increase to 300F or higher due to conduction and convection as the combustion process continues. This represents a steep temperature gradient and it is conceivable that under those conditions free or natural convection will take place in the gas

Jan 1, 1967

By R. B. Snow

THIS paper describes a technique of polishing and etching specimens of open-hearth furnace slags or hearth aggregates for identification of the crystalline constituents-lime (CaO), tricalcium silicate (3CaO•SiO2), dicalcium silicate (2CaO-SiO2), monticellite (CaO•MgO-SiO2), or forsterite (2MgO•SiO2), with especial emphasis on the mineral merwinite (3CaO-MgO.2SiO2). With proper standardization, this identification does not require the use of the petrographic microscope. The composition of basic open-hearth slags and furnace bottoms falls, almost without exception, within systems containing CaO, MgO, "FeO," MnO and SiO2, in which the number of basic molecules so greatly exceeds the orthosilicate ratio (two molecules of base to one of silica) that free basic oxides, and combinations between them such as aluminates or ferrites, are present in cooled specimens. Orthosilicates of (CaO + MgO) are the most common in such specimens, since in nearly all cases, except premelt slags, the molecular ratio of (CaO + MgO) to SiO2 is more than 2 to r. When sufficient lime is available it combines with the silica to form dicalcium silicate (2CaO•SiO2), which contains little, if any, MgO, FeO or MnO in solid solution whereas the latter oxides combine to form the oxide solid solution known as periclase. If the lime present is insufficient to form dicalcium silicate (2CaO•SiO2) it combines with MgO to form either merwinite (3CaO•MgO.2SiO2) or monticellite (CaO-MgO•SiO2); these minerals take little if any FeO or MnO into solid solution and the remaining MgO, FeO and MnO combine as periclase. This generalization seems to be valid for basic slags and furnace bottoms, since minerals such as CaO-MnO•SiO2 and CaO-FeO-SiO2 are found only in slags in which the lime-silica ratio is less than 2 and are not observed in specimens from furnace bottoms. The identification of crystalline constituents in such materials, especially of fine crystals in the groundmass, is difficult under the petrographic microscope. They are often masked by their neighbors because of their small size in relation to the thickness of the thin section and because of the presence of opaque or colored constituents. The indices of retraction and the optical sign of the mineral are sometimes difficult to determine because of the small size or because of twinning or of inclusions within the crystal. Moreover, the positive identification of merwinite (3CaO•MgO.2SiO2) from its optical properties is usually difficult in the presence of dicalcium silicate (2CaO•SiO2). CaO, MgO, 3CaO•SiO2 and 2CaO•SiO2 in open-hearth slags have been identified for a number of years in the U.S. Steel Corporation Laboratory by the usual

Jan 1, 1947

By Jonas Svensson

A new method is described for the production of cold-bonded pellets using a hydraulic binder, such as portland cement. Large-scale pilot-plant tests have proved that self-fluxing pellets of high reducibility and good handling strength can be made by the method. Blast-furnace trials have shown that the pellets are an acceptable burden material, comparable with self-fluxing sinter or heat-hardened pellets. Economic factors of commercial-scale production are discussed. The Grangcold Pellet Process—for which patents have been applied or already granted in a number of coun-tries—uses a hydraulic adhesive such as portland cement, slag cements, pozzolanic cements, etc., for the production of cold-bonded pellets. The idea of using a hydraulic binder for the agglomeration of iron-ore fines is not new. Portland cement was proposed as an adhesive for cold-bonded iron-ore briquettes in patents granted more than 50 years ago.&apos; In a report on the briquetting of iron-ore fines, published in Stahl und Eisen in 1959; it is stated that briquettes bonded with portland cement are used on a small scale at an ironwork in Germany. According to the report, the briquettes showed excellent strength in the blast furnace although their general use was made impossible because they required a long hardening time, during which they are sticky, soft, and difficult to store and handle. The Grangcold Pellet Process has overcome this particular disadvantage by mixing the balls with a suitable amount of the balling concentrate before storing them. The pellets are embedded in the concentrated during storing in such a way that they are isolated from each other and thus prevented from sticking together to form clusters. Thanks to the embedding concentrate, the pellets are subjected to a more or less uniform pressure from all sides which does not deform them. Thus, the mixture can be stored in a stockpile or in a bin until the pellets have hardened sufficiently. The concentrate is separated from the pellets by means of screening. The concentrate is returned to the balling operation and the pellets are either shipped to the blast furnace or stored for final hardening. The binder preferred for the Grangcold Pellett Process is portland-cement clinker, ground without the admixture of gypsum in order to avoid sulfur in the pellets as far as possible. Usually a 10% binder content is used. Two-thirds of the portland-cement clinker consist of lime and the rest is silica, alumina, and ferric oxide. Thus, self-fluxing or overbasic pellets are produced with this binder if the amount of silica in the concentrate used does not exceed 4%. The Grangcold Pellet Process was developed by the mineral Processing Laboratory of the Granges Co. Work started in 1963 with batch-scale tests. In 1966, a small pilot plant was put into operation in which 1800 tons of pellets were produced using 10% of rapid-hardening portland cement as a binder. Favorable results from a blast-furnace test with this batch led to the decision to erect a larger pilot plant which went into production in the summer of 1967. Since then, approximately 100,000 tons of cold-bonded pellets have been produced, mostly with 10% gypsum-free portland cement as a binder. Several full-scale blast-furnace trials have been performed with the pellets. The results of the trials indicate that the Grangcold pellets constitute a satisfactory blast-furnace feed. An industrial plant for the production of Grangcold pellets with a rated capacity of 1.5 million tpy is now under construction at the Granges Co.&apos;s mine at Grangesberg. The plant will come into operation in the summer of 1970. Results from Laboratory Work Pellets made from iron-ore concentrate bonded with portland cement harden slowly and their handling is very critical until they have hardened enough to loose their stickiness. It is therefore especially important to study the progress of the hardening action and the factors influencing it. This is best achieved by investigating the relationship between the compressive strength of the cement-bonded pellets and the curing time under varied conditions. The general course of this relation-

Jan 1, 1971

By K. I. Savage, S. C. Sun

This paper describes a process developed to recover coal, clays and pyrite from coal wastes. The process consists of fine grinding followed by coal and pyrite flotation which leaves the clays in the flotation pulp. A bituminous coal refuse containing 10% sulfur and 30% carbonaceous material was treated by this method to yield a coal product containing 4% sulfur, 10% ash; a pyrite product containing 45% sulfur (84% FeS2), 1% carbonaceous material; and a clay product containing 2% sulfur (3.5% FeS2). The coal yield was about 89%. The pyrite yield was about 77%. The process steps may be entirely flotation, or gravity separation (hydrocycloning) may be used to increase the pyrite : coal ratio in the flotation feed. Cost estimates for the process show a profit of $2.28 per ton of low pyrite grade refuse, but these do not include labor, maintenance, overhead and plant depreciation. The development of this process consisted of three parts: (1) exploratory tests, (2) op-timazation tests and (3) confirmatory tests. The objectionable qualities that sulfur imparts to coal have been commented upon from early times, and they have become more objectionable as the uses of coal have grown. In whatever form coal takes — raw, carbonized or gasified —the sulfur content remains objectionable, and therefore its compounds are removed as completely as possible. It has long been known that sulfur occurs in coal in different forms. In 1861, sulfur was said to exist in the state of sulfuric acid in combination with a base; in combination with iron as iron pyrites; as bisulfides of iron; and in combination with the organic elements of coal.&apos; Pyritic sulfur is a term loosely used to cover the sulfur associated with iron in its various forms. The mineralogically recognized forms are pyrite (FeS2), pyrrhotite (Fe 1-x S) and marcasite (FeS2). The particle sizes of pyrites vary widely. Isolated grains of marcasite smaller than 15 microns have been found disseminated through coal.2 Hair-like "veins" of pyrite filling cracks in vitrain have been found. At the other extreme, lumps or nodules of pyrites large enough for removal by hand picking have been encountered. Organic sulfur, unlike pyritic sulfur, does not exist as discrete particles, but is instead intimately associated with the coal structure and thus it is impossible to remove it or reduce its concentration by physical or mechanical means.2 In the preparation of coal for its various markets, the pyrite minerals (pyrites) are separated from the raw coal feed. This separation process concentrates the pyrites in the tailings or other waste products. It would be desirable to recover these pyrites for three reasons: (1) Pyrites are potential sources of sulfur and iron. In 1967, for the fifth consecutive year, Free World consumption of sulfur exceeded production.3 Propelled by the shortage, the domestic price of sulfur has risen from $24 to $38 per long ton (bright). (2) The refuse, when placed in piles, becomes ignited. The pyrites (FeS2) bum, giving off SO,. Thus, the pyrites are a cause of air pollution. (3) Also, the pyrites undergo chemical reaction when exposed to air. The refuse is leached by waters which result in stream pollution due to the water-soluble iron and acidic reaction products. Coal refuse also contains coal minerals and clay minerals. Therefore, any process for recovering the pyrites must successfully separate them from the coal and clay minerals. In the study discussed here, ten different bituminous coal refuse samples were successfully upgraded in pyrite content. These samples represented a wide variety of coal waste materials from Pennsylvania and other states. The variabilities of the sulfur and coal contents are shown in Table I. The extremes are Sample J, a high sulfur-low coal, and Sample B, a low sulfur-high coal. Definitions of some of the symbols or terms used in this report are given below: Mesh size—Tyler standard mesh screen sieves with an opening based on the square root of two. Fe —Indicates iron, as determined by a stannous reduction-dichromatic oxidation method. S—Indicates sulfur, as determined by the ASTM "Eschka" method for sulfur in coal.

Jan 1, 1969

By J. W. Freeman, E. E. Reynolds, A. E. White

Fram a study of 63 systematic alloy modifications it was found that molybdenum, tungsten, and columbium, added individually or simultaneously, and increases in chromium cause major improvements in 1200°F rupture strengths of Cr-Ni-Co-Fe base alloys. Rupture strengths were a function of the effect of composition modifications on both the inherent creep resistance and the amount of deformation the alloy would tolerate before fracture. THIS paper describes the results of an investigation of a series of alloys with systematic variations of the chemical composition of the following basic alloy: C, 0.15: Mn, 1.7; Si, 0.5; Cr, 20.0; NI, 20.0: Co, 20.0: Mo, 3.0; W, 2.0; Cb, 1.0; N, 0.12; Fe, 32.0 pct. The 62 modifications of this alloy were produced under conditions which minimized all factors influencing properties at high temperatures except composition. Melting, fabrication, and heat treatment were carefully maintained constant. Stress-rupture properties at 1200°F were used as the primary criteria of evaluation of the alloy. The objective of the study was to obtain data for determining the fundamental role of the influence of alloying elements on properties of heat-resistant alloys at high temperatures. In addition the results should be useful in determining optimum chemical compositions, the sensitivity of properties to variations in composition, and the degree to which alloy content could be reduced while retaining worthwhile properties. It is difficult or impossible to develop correlations between properties at high temperatures and systematic variations in chemical composition from published data for wrought heat-resistant alloys developed for gas turbines.&apos; &apos; The main reason for this is the extreme dependence of the properties on conditions of treatment of the alloys." In most cases variation in final treatments between alloys so influences the properties that the influence of chemical composition is obscured. In addition it is recognized Table I. Basic Alloy and Some Modifications Used Basic AllOy, Variations in Element Pct Composition, Pct C 0.15 0.08. 0.40. 0.60 Mn 1.1 0.03,0.25.0.50,1.0,2.5 S1 0.50 1.2, 1.6 Cr 20.0 10, 30 Ni 20.0 0, 10,30 Co 20.0 0. 10, 30 MO 3.0 0. 1.2.3, 5, 7 W 2.0 0, 1, 5, 1 Cb 1.0 0.2,4,6 N 0.12 0.004, 0.08, 0.18 Fe 32.0 that variations exist between heats of the same alloy which are related to melting practice and that there is a strong possibility that conditions of hot working influence response to final treatments. The development of heat-resistant alloys has been based on the gradual accumulation of data roughly related to composition from extensive testing programs. There is every reason to believe that in most cases the optimum compositions have been achieved by this procedure in the alloys commercially available. There are, however, very little data showing the influence of systematic variations of composition free from the influence of other factors, particularly for alloys of the type investigated. Several investigators of cast alloys have demonstrated compositional effects, notably Grant,1-6 Epremian,t Guy,8 and Harder and Gow.9 Sykes10 eviewed the work on the wrought alloy Rex 78 and the systematic variations of carbon, copper, molybdenum, and cobalt leading to the development of the stronger Rex 337A alloy. From the papers by Wilson11 and Henry12 it is possible to deduce the beneficial effect of substituting cobalt for iron in 0.45 pct C-20 pct Cr-20 pct Ni-4 pct Mo-4 pct W- 4 pct Cb alloys. Wilson mentioned but did not present the extensive compositional studies involved in developing these alloys. Binder" showed optimum properties for 3, 2, and I pct, respectively, for molybdenum, tungsten, and columbium in 20 pct Cr-20 pct Ni-20 pct Co-30 pct Fe alloys for limited systematic variations of these

Jan 1, 1953

By Yoichi Ishida, Ching-Yao Cheng, John E. Dorn

Tile creep behavior of a iron was investigated over the range of temperatures from 375° to 1150°K. Apparent activation energies for creep, obtained by the effect of sudden changes in temperature on the creep rate, revealed the presence of- four distinguishable regions. The creep behavior of a iron in Regions II (480° to 774°K) and 111 (775° to 1045°K) was found to correlate well with a model where the creep rate is controlled by the nonconsevualive motion. of jogged screw dislocations. An anomalous increase in the apparent activation energy fur creep in Region III was found to be in harmony with the known decrease in the free activation energy for self-diffusion over the Curie transformation range. Furthermore, the creep rates in Regions II and III were found to increase with stress due not only to the effect of stress on the activation energy but also to an increase in density of mobile dislocations. The evidence suggests that pipe diffusion along moving dislocations could be a significant factor over the lower temperatures of Region II. ALTHOUGH the creep properties of iron and steel have been of interest to metallurgists for some time and an extensive literature is now available, most of the published information has not produced much toward understanding the fundamental dislocation processes controlling the creep behavior of these materials. Whereas the activation energy for high-temperature creep of metals usually agrees well with that for self-diffusion, Sherby, Orr, and Dorn1 deduced from the data of Tapsell -and c1enshaw2 that the activation energy for creep of Armco iron is about 78,000 cal per mole and more recently Lytton and sherby3 reviewed the data of Jenkins and Mellor4 and found an activation energy for creep of a iron of 80,000 cal per mole. Both values are substantially greater than the activation energy for self-diffusion in a iron. Because of the limited data suitable for purposes of identifying the controlling dislocation mechanisms of creep and the unusually high activation energies for creep quoted above, it was considered desirable to reinvestigate in detail the creep of a iron by more reliable techniques which would provide sufficient data for determination of the creep mechanisms. EXPERIMENTAL TECHNIQUE Creep specimens were prepared from 3/8 by 4 in. iron bar stock of the following composition by weight percent: 0.001 C, 0.0120 0, 0.001 N, 0.004 S, and 0.003 P. The as-received bars were cold-rolled to a thickness of 0.100 in., annealed under argon for 30 min at 1113°K, cold-rolled to a final thickness of 0.063 in., and machined into tensile specimens having gage section 0.250 in. wide and 1.70 in. long. Finally they were recrystallized under argon at 1113°K. Specimens to be crept above 1060°K were recrystallized at 1173°K. Both recrystallization treatments gave the same reproducible equiaxed ASTM No. 4 grain size. Creep testing was conducted in machines fitted with Andrade-Chalmers arms that maintained a constant stress to within ±0.2 pct of the reported values. Deformation over the specimen gage section was sensed with a linear differential transformer and recorded auto-graphically as a function of time. The strains deduced from these measurements were sensitive to ±5 x 10-5. During creep the specimens were contained in an argon-filled chamber which was immersed in a temperature-controlled molten tin bath. Creep temperatures, as measured by thermocouples attached to the specimen, were maintained to within ±10.25°K of the reported values. For activation-energy determinations rapid changes in temperature of about 12°K were obtained within 30 sec by direct resistance heating of the creep specimen, and maintained to ±1°K of the reported values. Observations of structural details of specimens before and after creep tests were made by electrolytic polishing and etching in acqueous ammonium persulfate. EXPERIMENTAL RESULTS A typical example of the determination of apparent activation energies, Q, by the effect of small changes in temperature is illustrated in Fig. 1. Q is defined by

Jan 1, 1967

By E. A. von Hahn, T. R. lngraham

Cementation rates ulere studied by rotating an elec-tropolished or etched copper strip in aqueous solutions, of either perchloric acid or alkaline cyanide, containing silver ions. The rates of cementation were more rapid in acidic media than in cyanide media. In both, the rates varied with the rate of rotation of the copper strip. The deposits formed in the acidic solutions were finely divided, loosely adhering powders. Those formed in the cyanide solutions were dense and adherent. The presence of the deposits influenced the cementation rates. In the acidic solutions the rate was enhanced, possibly because of the increased cathodic area. In the alkaline solutions the rates were decreased in the presence of the deposits. This has been attributed to restricting the diffusion of the copper ion from the rnetal outward into the bulk of the solution. In an earlier paper1 the authors described a kinetic study of the cementation of palladium on copper in perchloric acid solutions. That work indicated that there were two stages in the palladium cementation process. The first, more rapid stage was consistent with rate control by the diffusion of Pd11 ions to the copper surface and/or by chemical reaction at the surface. The second stage was consistent with rate control by the diffusion of copper ions from the copper surface, through the deposit, out into the main body of solution. The effect of the type of deposit on the rate of cementation is of particular interest because it may be one of the primary features involved when large quantities of metal are to be cemented from solution. No substantial investigations of the effect seem to have been made. Accordingly, an extension of the previous work was arranged to study the cementation of silver on copper. This system was selected because of the convenience of the analytical methods, the previously established technology with copper, and the fact that the system could be studied in both acidic and alkaline media. By selecting perchloric acid and alkaline cyanide solutions as the media, it was hoped that some assessment might be made of the effects, on cementation, of having the silver ion present in a virtually uncomplexed state and in a highly complexed state. EXPERIMENTAL The cementation rates were studied, as previously described,&apos; by rotating a copper strip (1.0 by 23.2 cm) clamped to the peripheral surface of a lucite cylinder. The solutions were kept at constant temperatures (±0.05°C) under an atmosphere of purified nitrogen, and samples were taken periodically for analysis. The initial solution volume was 1000 ml and the sample volume 5 ml. The initial silver(1) ion concentrations were made low (0.5 to 1.0 x 10-4 moles per liter) to minimize the influence of the cemented deposit on rates. The solutions were prepared by dilution of suitable aliquots of silver perchlorate and silver cyanide stock solutions. Both stock solutions were prepared from purified silver powder (Johnson, Matthey, and Mallory Ltd.) with redistilled deoxygenated water, and they were kept under an atmosphere of purified nitrogen. To prepare the stock solutions, weighed amounts of silver powder were dissolved with nitric acid. For the AgC104 stock solution the silver nitrate solution was evaporated twice to near dryness with perchloric acid and then made up to volume: For the NaAg(cN)2 stock solution, the silver ions were precipitated with sodium hydroxide solution. The precipitate was filtered, washed thoroughly with redistilled water, dissolved with 1.1 times the required stoichiometric amount of sodium cyanide solution, and made up to volume. The small amounts of free perchloric acid and sodium cyanide present in the stock solutions were disregarded in the preparation of the solutions. The copper strips were cut accurately from 0.025-in. sheet (American Metal Climax OFHC brand) and annealed for 1.5 hr at 470°C in a stream of nitrogen. Analyses of the solution samples for silver and copper were done with a Techtron Model AA-3 atomic absorption spectrophotometer. Calibration standards of the same composition as the experimental solutions were prepared and analyzed simultaneously with the samples. No difficulty was experienced in the analyses, and the reproducibility was within 1 to 2 pct in both alkaline cyanide and perchloric acid solutions.

Jan 1, 1968

By B. C. Allen

Liquid surface tensions of copper and 18 Group IV-A to VIII transition metals (Ti, Zr, Hf, V, Cb, Ta, Mo, W, Re, Ru, Rh, Pd, Os, Ir, Pt, Fe, Ni. Co) have been measured by the static pendant-drop and dynamic drop-weight methods on the same rod sample. The drops were formed by electron-bombardment heating in high vacuum. Application of necessary corrections enabled determination of surface tensions to k2 pct and agreement between methods to * 1 to 4 pct for all the metals studied. Evidence is presented that the liquid surface was well screened by metal vapor, suggesting negligible adsorption of gaseous impurities and that the surface tensions measured are characteristic of the metals involved. Correlations between liquid surface tension and melting point, molar volume, heat of vaporization, and atomic number are presented and discussed. Temperature coefficients of surface tension were calculated using Eötvös&apos; law. SURFACE tension and interface energies of metals are the result of incomplete atomic coordination resulting in a force perpendicular to the boundary, tending to minimize its area. These energies are important in many phases of metallurgy, including microstructure, sintering, joining, electronic emission, and lubrication, which in turn affect many physical and mechanical properties of metals. Liquid surface tension refers to the interface between the liquid and its own vapor or nonreactive atmosphere, and is considered a physical property of the liquid. Since equilibrium shapes can be readily obtained with liquids, the units of surface tension (force per length) and interface energy (energy per area) are interchangeable. Thermo-dynamically, the surface tension ?LV is given by the change in free energy F with surface area A at constant pressure P, temperature T, and composition N: for commercially important refractory metals, vanadium, columbium, tantalum,13,14 molybdenum,14 and tungsten,l5 and none for the rare platinum-group metals and rhenium. Measuring the surface tensions of transition metals is difficult because of their high reactivity and melting points. Of the many techniques available,16-18 the pendant-drop 19-21 and drop-weight methods17,22 are considered superior because they can be modified to eliminate persistent sources of contamination such as supports and capillaries necessary in the popular sessile drop, capillary rise, and maximum-bubble-pressure techniques. The necessary modification is to melt a drop on the tip of a vertical rod, which provides support through a solid of the same composition.13,15 The object of the work was to study the surface-tension behavior of copper and transition metals, having reasonably low vapor pressures. Liquid surface tension of each pure metal was systematically determined by using a combination of the static pendant-drop and dynamic drop-weight methods on the same rod. Liquid drops were formed by electron-bombardment heating in high vacuum. EXPERIMENTAL WORK As indicated in Table I, the metals studied were high purity and generally were obtained in rod form. The exceptions were titanium and zirconium, which were machined from crystal bars, and molybdenum (tot 11, osmium, and ruthenium, which were sintered and arc cast into rods. All the metals were ground or swaged to desired sizes between 1- and 7-mm diam, and centerless ground round and smooth to a finish better than 50 µ in., rms. Each rod was thoroughly cleaned with steel wool, degreased, acid etched, and dried. In a typical run, the rod was vertically clamped in a modified floating-zone electron-bombardment furnace designed after Calverley23 and Carlson.24 The specimen was outgassed and maintained positive at several kilovolts in a dynamic vacuum of 10-5 to 10-7 mm. The bottom end was enclosed by a tantalum pillbox and heated by electrons emitted from a hot concentric tungsten filament mounted on a movable bracket. The bombardment power was slowly raised until melting was observed. Power requirements ranged from 30 w for copper to 1300 w for 4-mm tungsten. The stabilized and out-gassed drop of near-maximum size was photographed at 4. 1X on panchromatic film at desired time inter-

Jan 1, 1963

By C. S. Simons, G. Major-Marothy, M. A. K. Grice, D. A. Dahlstrom

The vacuum filter operating variables that influence cake moisture are discussed. The influence of temperature control, particularly through application of steam to the cake, is emphasized. Results of pilot plant studies on filtration of fine hematite concentrates are presented and discussed, and are shown to support the theoretically-derived conclusions. Results on fine magnetite concentrates are also used to support the argument. The relative merits of disc and drum filters from the standpoint of cake moisture are discussed. Moisture content has always been recognized as one of the most important properties of concentrates used as pellet plant feed. Most iron ore concentrates are produced by wet methods, and are finally de-watered on filters. Obviously, a real economic advantage accrues to the ability of control the moisture content of the filter cake within the range required for optimum pellet production. Another consideration, also, has been receiving increasing attention recently. Transoceanic shippers of concentrate cargoes are critically assessing the hazards of excess moisture. The nature and magnitude of these risks have been described, &apos; and it appears that their elimination may require that residual moisture be somewhat lower than the limit for proper pelletization. Coarse, very free-filtering materials, such as the products of spirals, are usually best handled on top-feed types of machines. The moisture content of the cake may be held at a specified value by proper design and operation, taking into account cake thickness, air-flow rate, and drainage time. Fine-grained concentrates, with which we will be concerned here, must be filtered on Drum or Agidisc machines. With many of these materials, it is possible, by proper design, to meet cake moisture requirements with a conventional filter station. The first installations to produce high-grade pellets from magnetic taconites fell in this class. In fact, the design criteria were developed in connection with operations of Reserve Mining Co. at Silver Bay, inn.,2 and these have been verified repeatedly in other mills. The trend today, however, is toward the production of more difficultly dewatered concentrates. This is due on the one hand to the increasing attention being given to non-magnetic ores, which tend to be far slimier, and therefore much more retentive of moisture, than the magnetites. On the other hand, the pressure to improve the grade of the magnetic ores is leading to finer grinds, which also are more difficult to dewater. In the latter case, the decision to improve grade in an existing operation by finer grinding for better liberation may lead to two unattractive alternatives: 1) substantially higher bentonite consumption, plus the risk of poorer quality pellets, from high cake moisture, or 2) installation of a thermal dryer. There is, however, a third alternative. In recent papers by two of the authors3,4 it was shown that for many materials a significant decrease in cake moisture can be obtained by applying live steam to the cake face during the drying part of the filter cycle. Further, this limited drying appears to have distinct economic advantages compared to thermal drying. It is the purpose of this paper to explore the third alternative. To do this, the results of an extensive pilot study of steam filtration of a hematite flotation concentrate will be critically examined. This study was sufficiently broad so that a number of alternate suggestions (besides steaming the cake) for reducing moisture content were tested, and comparative data for both Drum and Disc filters were obtained. The work was particularly interesting since the concentrate has a high Blaine surface, and is therefore particularly difficult to dewater to the levels required. FILTER CAKE MOISTURE The significant difference between concentrate filter cake as discharged from the filter, a cargo of that same filter cake during or after shipment, and a green ball formed from that filter cake is in the relative volume of voids, or porosity. In every case, the material is a collection of small solid particles held together by the cohesive forces of a liquid. The physical properties of the aggregate are determined by the

Jan 1, 1967

By G. S. Cole

The temperature has been measured ahead of stationary solid-liquid interfaces under conditions approximating luzidirectional heat flow and therefore unidirectional solidification. Natural convection flow patterns may be deduced from the temperature distributions , temperature fluctuations, and shape of the interface. Fluid flow increases with the height and the rate of heat transfev through the interface and this is further manifested by a deviation of the interface from aflat vertical plane. The influence of fluid flow on solute inhomogeneity during alloy crystal growth can be inferred from the observed temperature distributions. A buoyancy force exists in the liquid ahead of a vertical solid-liquid interface, caused by a difference in density between cold fluid near the interface and warmer fluid in the bulk liquid. When the viscous and inertia forces in the melt exceed this buoyancy force, a flow of fluid takes place, termed natural or free thermal convection. Natural convection in purely liquid systems has been extensively studied for many years. 1"u On the other hand, fluid flow during horizontal crystal growth has oniy recently been the subject of experimental investigation."-25 The requirements for horizontal crystal growth differ from other heat flow systems. The small aspect ratio (ratio of height of cold wall to length of fluid) has never been considered. The uniform furnace gradient which supplies heat radially (and not necessarily symmetrically) differs from previous boundary conditions of uniform heat flux at the cold and hot ends. And most important of all an isothermal s/l interface is present which can adjust its shape and position to conform to heat and fluid flow. All of these boundary conditions involve complexities which cannot be readily solved analytically. Preliminary observation has demonstrated the penera1 shape of the natural convective flow pattern in transparent media.20&apos;24&apos;25 The flow is circulatory, directed toward the interface at the surface of the liquid, down and away from the interface at the bottom, and then up at the hot end of the melt. During crystal growth such a flow may interact with the solute boundary layer at the s/l interface to affect solute incorporation.M&apos;1B|28&apos;i!T Evidence has also been presented recently to show that thermal convective flow will affect the structure of ca~tin~s.~~-~~ The rate of heat transfer (conduction plus convection) in a given fluid system is a function of the temperature difference between the hot end of the liquid and the s/l interface and the height of the interface. At the lowest values of these variables* all heat is *It has been shown&apos; that adverse temperature gradients as low as O.OOS°C oer cm are sufficient to cause convection. transferred by conduction. When the temperature difference or interface height are increased, laminar fluid flow commences and heat transport takes place by laminar convection as well as by conduction; turbulent heat transfer takes place at higher values of these variables. In the transition region between laminar and turbulent flow, boundary layer separation takes place; fluctuations in temperature are also noted and increase in amplitude and frequency as turbulence becomes dominant. In this paper, fluid flow patterns in the melt ahead of a stationary interface are deduced from observations of temperature distribution and fluctuations, heat flow rate, and interface shape. The fluid flow ahead of advancing interfaces and the effect of such flow on solute incorporation may be inferred from these measurements on stationary interfaces. Observations during enforced fluid motion will also be considered. EXPERIMENTAL PROCEDURE The metal was contained in a lava boat 10 cm in length, 1+ cm in width, and 2 cm in height, as shown in Fig. 1. A water-cooled, molybdenum block heat-sink is at one end of the boat; surrounding this assembly is a slotted stainless-steel tube noninductively wound with a nichrome heating element. Temperature was measured by 38-gage Chrome1 vs Alumel thermocouples sheathed in 0.05-cm-diam graphite-coated stainless-steel tubing, which were moved longitudinally and vertically through the melt by means of a two-dimensional motorized micrometer stage. In some experiments the thermocouple junction was exposed, but in the majority of experiments the junction was welded to the sheath tip; no significant difference

Jan 1, 1968

By D. S. Flett, A. W. Fletcher

Equilibrium studies on the extraction of nickel and cobalt with kerosine solutions of naphthenic acid have shown that an exchange extraction reaction occurs at pH 5.5. The nickel/cobalt separation factor is constant at 1.8 for constant total metal molarity and varying nickel/cobalt ratios. The separation factor decreases with increasing total metal molarity in the organic phase beyond 0.2 M and also decreases with increasing temperature. From the equilibrium data, it has been possible to derive a mathematical model for the separation of nickel from cobalt by exchange extraction in multistage systems. Experimental data from a continuously operated multistage mixer/settler apparatus has shown a reasonable correspondence with computer-calculated data. The effective separation of nickel and cobalt in sulfate solution remains a problem in hydrometallurgy and the hope that this would be solved by solvent extraction has not yet been fulfilled. With chloride solutions, advantage may be taken of the ability of cobalt to form anionic complexes with the chloride ion. It can then be readily separated from nickel, which does not form stable chloro complexes, by extraction with a suitable long chain amine. However, in hydro metallurgical operations, sulfate solutions are generally obtained in which no extractable anionic species are present. Thus, the possibility of using cationic extractants must be considered, and in this paper attention is directed to the use of carboxylic acids. The method of separation studied has been termed exchange extraction, which involves replacement of a metal in the organic phase with a more acidic metal in the aqueous phase. Thus, (BR2).+ (Az+)aqt=(AR,).+ (B2+)aq (I) where metal A is more acidic than metal B, R represents the acidic radical derived from the acid RH, and the subscripts e and aq refer to the organic and aqueous phases, respectively. Ashbrook and Ritcey&apos; have used this method for the separation of cobalt from nickel using the sodium salt of di-2 ethyl hexyl phosphoric acid, which preferentially extracts cobalt. Some nickel is coextracted, and this is removed by exchange with cobalt ions in the feed solution by suitable countercurrent operation in a pulsed column. Much work has been carried out by a number of workers in Russia on the general use of exchange extraction for the separation of metal ions using car-boxylic acids. Gindin et aL a have demonstrated that this technique could be applied to the separation of nickel from cobalt using a C--C. carboxylic acid and have applied the technique to the production of high purity cobalt solutions for electrolysis. Further worka was concerned with the development of a process for the separation of nickel from cobalt in a pulsed column. This system permitted the separation of iron and copper from nickel and cobalt in one system. The procedure involved center feeding with acid backwashing at the top and alkali addition lower down the column. Thus the system operated under a pH gradient and the metals were distributed in the column in the order of their basicities. A similar application was studied by Gel&apos;perin et al,4,5 for the removal of copper and iron impurities from a nickel anolyte by means of a C10-C,12 fatty acid fraction. Ginden et al,&apos; and Fletcher and Wilson&apos; have studied the effect of pH on the extraction of a number of metals with carboxylic acids. These studies showed that metals such as iron, copper, lead, zinc, nickel cobalt, and manganese are extracted at pH values close to the pH of hydroxide precipitation. Nickel is extracted at a slightly lower pH than cobalt and thus the nickel/cobalt separation factor has a value not much greater than 1. More basic work on complex identification has been reported by Fletcher and Flett: by Tanaka; and Jay-cock and Jones." These studies have suggested that at low loadings in the organic phase, the nickel and cobalt carboxylates appear to be dimeric and solvated by free carboxylic acid molecules. As the concentration of metal in the organic phase increases, the complex changes and larger polymeric species are formed. In order to permit assessment of the potential of carboxylic acids as extraction reagents for separation of

Jan 1, 1971

By F. D. Hoyt, H. L. Hartman

The development of new processes and methods by The Pennsylvania State University to improve slate quarrying technology has centered in recent years on cutting and sawing stone in the quarry to eliminate a second cutting process in the mill. Two machines exhibit promise for this work: 1) a circular saw mounting diamonds or hard inserts to produce smaller sizes of stone and 2) a chain saw with insert cutting teeth to produce stone in the larger dimensions. Prototype machines have been constructed and tested in several Pennsylvania slate quarries, and one commercial installation has been operated for several months with a circular diamond saw. Other kinds of dimension stones may be cut by these saws. Research at Penn State has begun to study the fundamental cutting action of rotary tools or saws in slate and other dimension stones. A laboratory drill press is being instrumented to permit thrust-torque-rotational speed us penetration rate studies of single tooth cutting surfaces on stone. Machinability studies of slate conducted with tungsten-carbide inserts have been performed. The dimension stone industry generally accepts the rather basic premise that the larger the block removed from the quarry, the more practical and economical the operation. Thus, the concept of cutting to size any dimension stone while it remains in place in the parent bed would receive little consideration from the majority of members of the industry. However, the slate industry, which is usually considered a separate member of the dimension stone family, is pioneering in the development of an in-place sawing method. Before any final decision can be reached concerning a proposed new system, it is essential to take a long, hard look at the present method of operation in order to determine if the new system is indeed an improvement or even desirable. In the following section is a brief description of present quarry practice in the slate quarries of eastern Pennsylvania. PRESENT METHOD OF QUARRYING SLATE In the numerous slate quarries of Lehigh and Northampton Counties of Pennsylvania, the grain and cleavage of the slate are most often at right angles to each other; if a third surface is broken at right angles to these two natural planes of weakness, blocks of more or less rectangular shape can be separated.&apos; In conventional quarrying a large calyx core drill prepares holes of 36-in. diam in which wire-saw standards are positioned. By wire sawing between strategically located core-drill holes, large sinks or benches of virgin slate are opened up. The sides freed by wire sawing will vary from quarry to quarry but generally are rectangular in shape with dimensions averaging 20 ft in length and about 15 ft in depth. Some quarries are fortunate in having a joint or natural parting to work to, which of course diminishes the amount of core drilling and wire sawing required. Once the various benches have been developed either through wire sawing alone or through a combination of wire sawing and natural jointing planes, the block removal proceeds in the following manner. A plug hole is drilled in the block with a compressed-air hammer and a feathering chisel is inserted in the hole to cause a fracture of the rock either with or against the grain as indicated by the positioning of the so-called feathers. This operation is referred to as sculping. After a block has been freed with and against the grain by means of wedging from the cross fracture with long bars or levers, the block is further freed along the cleavage plane by shimming it up with small wooden pieces in an operation known as styling. A large steel loading chain is wrapped around a block thus freed and the chain is attached to the wheel of an overhead cable. The block is then hoisted vertically to the cableway and moved along this cableway laterally to the lip or edge of the quarry. From here it is unloaded onto a rail car or truck for transportation to the processing mill. Except for occasional blasting to free stubborn blocks,

Jan 1, 1961

By H. Groeneveld, C. A. Connally, P. J. Hoenmans, J. J. Justen, W. L. Mason

A miscible displacement pilot using a slug of LPG driven by separator gas was conducted in the Cardiurn reservoir of the Pembina field. The injection pattern was a 10-acre, inverted, isolated five-spot. Upon completion of the LPG-gar phase, an experiment was conducted using a slug of water followed by gas. Calculated performance of the pilot is compared with actual performance. Equations are developed to calculate the distribution of LPG into zones of varying permeability, to estimate the progress of the flood at different times in the various zones and to estimate gas rates after breakthrough. The analysis indicates that permeability stratification was a dominant factor in controlling oil recovery and that oil was completely displaced from the swept pore volume. The results of the pilot indicated that miscible flooding is a practical means of pressure maintenance in this reservoir. The total recovery from the pilot area was good in spite of the early breakthrough of LPG. The effects of stratification were reduced by injecting a slug of water into the partially swept reservoir. INTRODUCTION The Pembina field,&apos; located in Alberta, is the largest oil field in Canada and one of the largest in the North American continent. The reservoir is a stratigraphic trap producing from the Cardium sand. Neither bottom water nor free gas has been found. The recovery of oil by the natural depletion mechanism has been estimated at 12.5 per cent. Pressure maintenance studies of various areas have indicated that the recovery can be increased 21/2 times by water flooding, and a large area of the field is presently under water flood. However, reservoir studies of the North Pembina area indicated that miscible flooding might be competitive with water flooding. A pilot test was conducted to evaluate the performance of a miscible flood. A 10-acre, inverted, isolated, five-spot pattern was selected for the pilot. The pattern area was large enough to minimize wellbore fracturing effects and contained sufficient oil to provide significant working numbers. The performance of each of the four producers could be evaluated individually and compared. In the event of breakthrough in one direction, the effect would be isolated from the other producers. The use of a single injector minimized the volume of LPG required, and, because of the high mobility of gas, one well was sufficient to inject the necessary daily volume to replace the high rate of production. With four producers, the test could be completed in time for results to be evaluated, additional engineering studies to be made and a unit to be formed before the reservoir pressure in the North Pembina area declined below the bubble point. The pilot was located in an area developed on staggered, 80-acre spacing. The injection well was drilled at a regular location, while the four producers were drilled 467-ft north, east, south and west of the injector. Each quadrant and its associated producer were identified according to their direction from the injector— that is, north, east, south or west. The eight surrounding producers on 80-acre spacing were shut in to isolate the pilot area and provide for reservoir pressure observation. The pilot wells were completed using permanent-type completion techniques. After coring, casing was run through the pay section and cemented. Inside 51/2-in. casing, 2 1/2-in. tubing was hung. The wells were perforated opposite the Upper Cardium sand and lightly fractured. Fracturing volumes, rates and pressures were low to minimize the extent of the fractures. The fracturing treatments average 1,000 lb of 20-40 mesh sand in 700 gal of a low fluid-loss sand-carrying agent. Feed rates and wellhead fracturing pressures averaged 5.5 bbl/min at 2,535 psig, respectively. After fracturing, the productivity index was measured in each of the five pilot wells. The average PI of the four producers was 0.41 BOPD/psig drawdown. The measured PI&apos;S were approximately the same as PI&apos;S calculated from core analysis data, indicating that the fracturing treatments were just sufficient to overcome

By J. W. Downey, A. E. Dwight, M. H. Mueller, H. Knott, R. A. Conner

Sixty new ternary equiatomic compounds are reported with a hexagonal crystal structure that is isostructural with or very similar to Fe2P, D3h-P62m. HoNiAl is a typical example, with a, = 6.9893 ± 0.0003Å, C, = 3.8204 ± 0.003Å, and c/a = 0.54 7. Three holmium atoms occupy (g): x,0,1/2 three aluminum atoms occupy (f): x,0,0; one nickel atom occupies (b): 0,0,1/2; and two nickel atoms occupy (c): 4, + , 0. The nonequivalent 1(b) and 2(c) sites give rise to two sets of unequal interatornic distances (i.e., Ho-Ni and Al-NL in the case above), which account for the prevalence of Fe2P-type tertmry compounds and the scarcity of binary examples. Unit-cell constants are presented for the sixty compounds and density measurements on the compounds HoNiAl and UFeGa confirm that three formula weights are present per unit cell. Neutron and X-ray powder diffraction intensity measurements were made on CeNiAl and HoNiAl, respectively. The atomic posiLiotml parameters in CeNiAl were determined from neutron data to be x = 0.580 5 0.001 for cerium and 0.219 5 0.001 for aluminum. An investigation of the quasibinary section between the binary compounds CeNi2 and CeA12 revealed a new ternary compound CeNiAl. The compound has a hexagonal structure and is isostructural with the prototype compound Fe2P. Additional examples discovered or confirmed in this investigation provide a total of sixty ternary compounds that are isostructural with or closely related to Fe2P. Previous investigators1&apos;2 reported the unit-cell constants for the hexagonal compounds UFeA1, UCoAl, UIrA1, ZrNiAl, ZrNiGa, HfNiAl, and HfNiGa and the present investigation has confirmed that the compounds are isostructural with Fe2P. Independently, Steeb and petzow3 reported the same structure type for UCoAl, UIrA1, and UNiA1. However, the present results suggest a different atomic site occupancy for the component atoms in the three compounds. A detailed investigation of the relative positions of the three kinds of atoms in the compounds CeNiAl and HoNiAl will be discussed. EXPERIMENTAL PROCEDURE The equiatomic alloys were prepared from elements of 99.9+ pct purity by arc melting under a helium-argon atmosphere. After homogenization at temperatures from 700" to 900&apos; C, a metallographic examination was performed by conventional methods, and density measurements were carried out by the immersion method in CCl4. A powder sample was prepared for diffraction studies by crushing a portion of the annealed button. X-ray diffraction patterns were obtained with a Debye-Scherrer camera, in which the annealed powder was glued to a quartz filament, and indexed with the aid of a Bunn chart. Unit-cell constants were calculated from the computer program of Mueller, Heaton, and Miller4 and d spacings were obtained by the program of Mueller, Meyer, and Simonsen.5 The intensity values were calculated from the relation I, ~ (m)(L.P.)F2 by a computer program written by Busing, Martin, and Levy.6 The absorption and temperature correction factors were neglected. An X-ray study of HoNiAl was carried out to take advantage of: large differences in atomic scattering factors for holmium and aluminum, X-ray patters free of background darkening, negligible oxidation at room temperature, and negligible weight loss in the preparation of this alloy. The neutron diffraction studies were made on a powder sample of CeNiAl contained in a -in. diam V tube and a pattern was obtained with neutrons of wavelength The neutron scattering factors employed (x 10-12 cm). In contrast to the scattering amplitude for X-rays, cesium does not have the largest cross section, however, there is a sufficient difference in the neutron scattering amplitudes to distinguish between the atomic species. The neutron transmission was high, 86 pct; therefore, absorption corrections were not necessary for the cylindrical sample. Most reflections could not be observed individually, because of the relatively large unit cell (a = 6.9756 and c = 4.0206Å) and relatively short neutron wavelength; therefore, the intensity of grouped reflections was considered. The Kennicott modification7 of the Busing-Martin-Levy program6 was employed to determine the identity of the atoms at the various lattice sites and the positional parameters. RESULTS A structure for the prototype compound Fe2P was first reported by Hendricks and Kosting;8 however, the structure was in error. The correct structure, as reported by Rundqvist and Jellinek,9 is as follows. The unit-cell constants and volumes per formula weight (V/M) are given in Table I for the sixty compounds examined in this investigation and classified as Fe2P-type compounds. The structure type was determined initially from a comparison of the unit-cell constants of HoNiAl with other known examples of this structure type1&apos; and from the density of HoNiAl, given in Table 11. The density indicated that three formula weights comprised a unit cell, as in the prototype compound Fe2P. The assignment of the three species to lattice sites was made initially on the basis of atomic size. The large holmium atoms were assigned to the 3(g) sites that have a relatively large interatomic distance to nearest neighbor positions, the small nickel

Jan 1, 1969