Search Documents

By M. C. Ruiz

The leaching behavior of chalcopyrite concentrate in acidic CuC12-NaCI-O2 solutions was investigated. Experiments were conducted under continuos flow of oxygen at atmospheric pressures. The results indicated that among the variables temperature has the largest influence on the dissolution of chalcopyrite in this medium, and high copper extraction can only be obtained at temperatures near the boiling point of the solution. It was also found that the stirring speed did not influence appreciably the dissolution of chalcopyrite. An increase in the oxygen flow rate up to 0.1 1/min increased the copper extraction. The total chloride concentration affects the dissolution of chalcopyrite up to about 4 M. Copper extraction of 93 % was obtained in leaching chalcopyrite of size fraction -400 # Tyler at 105 OC in 2 hours.

Jan 1, 1997

By Junhong Noh, Kug Sun Hong, Jung-Kun Lee, Bo Ding

"The photocatalytic splitting of water into H2 and O2 by oxide nanoparticles has received much attention. However, the full potential of photo-catalysts for efficient hydrogen generation out of water has not been fully realized yet due to unresolved limitations including the low electrical conductivity and ineffective carrier extraction. Here, we report composite oxide materials consisting of 1-dimensional (1-D) transparent conducting oxide (TCO) core and TiO2 shell. Highly conductive ITO nanowires were grown on a flexible SUS mesh as a core component. The photoelectrodes consisting of these 1-D nanocomposites have increased carrier mobility due to the TCO core, while the TiO2 shell provides the photocatalytic functionalities. In addition, the built-in-potential at the interface between TCO core and the TiO2 shell improves the collection of charge carriers from TiO2 to TCO. These factors altogether contribute to increasing the photocurrent of the device under light.I. IntroductionPhotocatalytic behavior of semicondcutors has been extensively explored since it was discovered in TiO2 in 197Os. When TiO2 is exposed to UV light, the light is absorbed and electron/hole pairs are generated in the conduction and valeence bands. Holes in valence band will oxide/mineralize pollutant target directly or indirectly (via mediator hydroxyl radical). If the adsorbed A is O 2, O 2 will react with electron from conduction band to generate hydroxyl radical as described in the second set ofreactions. The photocatalytic reaction is schematically explained in Figure 1.Photoelectrochemical (PEC) cells using the photocatalytic reaction have attracted emerging interest as a potential route to convert solar radiation into useful forms of energy by reaction such as water splitting to generate hydrogen1 or the reduction of carbon dioxide.2 Another application ofphotocatalysis is water splitting and CO2 reduction, both of which utilize the electrons that are optically excited to the conduction band. 3•4 For this purpose, the conduction level of the semiconductor should be higher than hydrogen production level (EHZ1HZO) while the valence band should be lower than water oxidation level (Eo21112O). Electrons and holes will be generated on the semiconductor site, and holes generate O 2 at semiconductor site, while electrons will migrate to counter electrode to execute reduction forming H2. In addition to that, materials should be chemically stable to resist photocorrosion and have long lifetime of electron/hole pairs. TiO2 is a suitable material from the viewpoint of band arrangement and chemical stability requirement"

Jan 1, 2012

By P. H. Scaife

The pyrometallurgy industry faces a series of environmental challenges, based on local, national and global issues. While local impacts continue to be important, national and global concerns with Sustainable Development, Greenhouse emissions, Acid Rain and water resources are key strategic drivers for the industry. The environmental problems of the industry are well known: emissions of sulphur dioxides and carbon dioxide, disposal of arsenic wastes, consumption of fresh water, fate and impact of minor components/trace elements in raw materials (whether conventional or complex, or wastes). Solutions to these problems require the application of Cleaner Production principles (waste minimisation, energy conservation, product design to enable ease of post consumer recycling), new technology and scientific studies to assess impacts of discharges. A number of opportunities, driven by environmental concerns, have also been identified

Jan 1, 1994

By A. P. Paiva

With the aim of establishing a valuable alternative to the conventional methods, studies regarding the recovery of precious metals by solvent extraction have been increasing over the past few years. In this work, the selectivity of extraction presented by Cyanex 471X toward silver is investigated. Simulated chloride solutions considering contents of iron and copper usually present in actual leaching practice were used. The characterization of the aqueous solutions - in terms of the multiple equilibria established by the chlorocomplexes of the different metals and their relation to the total chloride concentration of the base-electrolyte - was successfully carried out by cyclic voltammetry. The results obtained support the important contribution of the electrochemical techniques for the understanding of the overall extraction phenomena.

Jan 1, 1994

By James D. Navratil

Although liquid membranes have several advantages over conventional liquid-liquid extraction, problems such as membrane instability remain. In order to solve these problems, we have combined an electrostatic field with the principle of liquid membranes and developed a novel reactor system for rare earth recovery. Our cylindrical reactor, filled with extractant and diluent, is divided by means of a perforated cylinder into an outer annular extraction cell and an inner stripping cell. Below the extraction and stripping cells are two settlers for the aqueous solutions. The design of the reactor permits the organic solution to flow freely through the special perforated cylinder and the added feed and strip solutions, outside and inside the perforation, respectively, to be completely separated.

Jan 1, 1990

By Michael S. Moats, Jan D. Miller, Wlodzimierz W. Zmierczak

"For many, hydrogen in a pure hydrogen economy would be like natural gas in today’s energy economy. Unfortunately, hydrogen’s physical properties are unsuited to the energy market’s requirements in terms of packaging, storage, transfer, and delivery. In this paper, a hybrid energy economy that packages hydrogen chemically on carbon atoms from various sources including recycled carbon dioxide is introduced and discussed. For this new hybrid energy economy to become a sustainable reality, the ability to recycle carbon dioxide and use hydrogen to create an appropriate energy product, such as dimethyl ether (DME), is needed. DME is recognized as a potential next generation, “beyond-petroleum”, environmentally benign commodity for energy storage and distribution. It is expected that to maximize the sustainability of the proposed hybrid energy economy, “green” hydrogen will be utilized. The “green” hydrogen would be created by the electrolysis of water powered by renewable energy sources, such as solar, wind or geothermal heat.IntroductionWith the growing concerns surrounding trends in global warming and increasing concentrations of “greenhouse” gases, such as CO2 and CH4, efforts to mitigate the emission of these gases from industrial sources are growing. With respect to CO2, the demonstrations of various capture and sequestration methods are underway around the world.The sequestration of CO2 is mainly focused on storing the gas underground or deep in the ocean. The Intergovernmental Panel on Climate Change (IPCC) estimates that 2000 Gtonnes of CO2 can be stored underground in depleted oilfields, un-minable coal beds and other geologic features [1]. Additionally CO2 may be stored at the bottom of the ocean. The lure of storing carbon dioxide in depleted oilfields or un-mineable coal seams is that an economic benefit (enhanced oil or methane recovery) can offset the costs of gas capture, transportation and storage. Unfortunately, all of these storage methods have potential for the release of CO2 or CH4 back into atmosphere or creating environmental damage (mobilizing heavy metals, disrupting deep sea ecology)."

Jan 1, 2008

By R. Ratnagiri, B. Minaie

"In order to expeditiously produce defect-free metallic components in materials processing applications, the relationship between the process parameters and the product properties needs to be well understood while minimizing the production engineering iterations. To achieve this goal, a realistic mathematical formulation of the process should be carried out and an appropriate numerical modeling of various phenomena occurring in such process should be implemented. The materials processing of transforming the molten material into a finished metallic component involves fluid flow and solidification/melting. In the present paper, a finite element based analysis of the fluid flow ·and solidification/melting phenomena in cavities is presented and the various issues in modeling these phenomena are discussed. These transport phenomena play an important role in determining the final characteristics and material properties of the part by affecting the formation of defects and microstructure. A realistic numerical modeling of these phenomena can significantly reduce the rejection rates during the process and can increase the quality of the final product.IntroductionDuring the intelligent materials processing of various metallic components, it is often required to have a thorough knowledge of the behavior of the transport phenomena involved in this process. This is due in large to the coupling that exists between the transport phenomena and the final material properties of the components produced during materials processing. This interrelationship demands that the pertinent transport phenomena in the form of fluid flow and solidification/melting be studied and predicted accurately. In many materials processing applications, the fluid flow is in the form of either a forced convection free surface flow intended to fill a cavity or a natural convection flow resulting from the gravity when the cavity is filled. In either case, the phase change in the form of solidification/melting is also involved in order to complete the process. However, the thermal history during this phase change has a direct impact on the material properties of the final part and the possible defect formation that may be involved. This thermal history itself is dependent on the nature of the fluid flow during the earlier stages of the process. As such, there is a coupling between the fluid flow, phase change, microstructure, and defect formation in the resulting component. It is therefore necessary to analyze these phenomena in order to find optimum methods to produce good quality parts by minimizing the defects that may be generated. Such an analysis can result in the development of appropriate numerical models for the process that can facilitate the economical and timely manufacturing of various components with high consistency. The present paper discusses the issues related to the transport phenomena encountered during materials processing of components engineered largely by using various combination of convective fluid flow and solidification/melting in cavities."

Jan 1, 1994

By Tiejun Chun, Marcus Emrich, Jian Pan, Deqing Zhu, Vinicius Mendes

"Joint projects of studies of hematite acid pellet have been implemented to develop technological solutions for using Vale hematite pellet feed in Chinese palletizing plant. Beneficial improvements on the pellets quality were achieved by adjusting the blends composition and using new technology of pre-treating the blended pellet feed with HPGR (High Pressure Grinding Roller) on rotary kiln pellet technology. The drop strength of green balls increased from 3.4 to 6.0 times from 0.5m height, at the same time, the bentonite dosage decreased from 1.5wt% to 0.7wt%. The compressive strength of roasted pellets reaches 2500 N/pellet. The reduction swelling index of roasted pellets is below 15%.IntroductionWith the fast development of steel industry in China, the production of pellets has been further expanded. Pellets are used as a high quality charge for blast furnace and the annual output is around 80Mt pellets [1]. According to the developmental trend, sinter will be replaced by pellets due to the larger environmental impact of sintering plants when compared to pelletizing plants. For example, the specific CO2 emission in sintering process is around 2.5 times higher than in pelletizing process. However, the steel industry of China has been confronted with a serious shortage of domestic pellet feed due to the low iron grade of Run-of-Mine ore despite of huge reserves of iron ores [2]. Therefore, more pellet feed, mainly hematite, has been imported to make pellets."

Jan 1, 2011

By K. Krishnapisharody

A mathematical model has been developed to predict the interface dynamics and droplet generation of the buoyant phase in a two-fluid system. The model employs the well-known SIMPLE algorithm for obtaining flow fields and the Volume of Fluid (VOF) method, for interface tracking. The implementation of the model in water-oil systems, where the oil layer is placed above a recirculating water bath, is discussed. The evolution of the water-oil interface leading to the formation of oil droplets is computed realistically.

Jan 1, 2008

By Takashi Miyamoto, Hideo Nakae, Hideki Yamaura, Takeshi Yanagihara

"For the production of partially composed metal matrix composites, namely discontinuous MMCs, using a casting· process, the interpenetrated phase composites with SiC particles were fabricated by pressureless iDfiltration using molten Al-Si alloys. This process is based on a wetting phenomenon, therefore, we discussed the technique based on the reactive wetting. The SiC particles coated by diluted water glass were sintered in a mullite Tammann tube and simultaneously infiltrated with molten Al-Si alloys in air at 1173~1573K. As for the improvement of the wettability between the SiC and the liquid aluminum alloy, Fe3O 4 powder was mixed with the water glass due to the thermit reaction between Fe3O4 and molten aluminum alloy. In some experiments, pure aluminum powder was placed on the sintered SiC to increase the interfacial area and the chemical reaction between the sintered Sic. and the melt. By combining these conditions, we succeeded in the complete infiltration without pressure at 1173K.IntroductionAs is well known, the mechanical properties of metal matrix composites (abbreviated MMCs) are superior than that of ordinary metals. However, their use has not been widely accepted because the production cost is very high due to their poor machinability. Therefore, the production of partially composed, namely discontinuous MMCs, by as the Lanxide process [l,2] has been investigated for many years. The Lanxide process, it takes a long time, sometimes up to 10h, in a nitrogen atmosphere for the infiltration. Therefore, the cost will be higher for common use. On the other hand, a high 'pressure process has been adopted for the production of discontinuous MMCs by the Toyota Motor Corp.[3]."

Jan 1, 2000

By Jefferson Caponero

The tire is an expressive component of Municipal Solid Waste, manly when its occupied volume is considered. Its treatment by pyrolysis stands for a list of advantages, such as: landfill releasing and a production of a high quality fuel. The exploitation of new natural resources is becoming more difficult each day, basically due to the environmental damages caused by this type of activity. This work presents a study on the thermal behaviour of Brazilian tires using thermogravimetric analysis and differential thermal analysis, in order to optimise the pyrolysis process of tires. Samples of I to 2 mm were investigated at atmospheres of nitrogen, argon, oxygen and mixtures of these gases at temperatures up to 1273K, under heating rates between 1 to 50 Klmin . The results showed that the behaviour of each sample is related to both the atmosphere composition and the heating rate.

Jan 1, 2001

By A. Siegmund, R. D. Prengaman

Lead anodes used in zinc electrowinning generally contain 0.5 - 1.0 % silver to reduce the rate of corrosion over the service life. For good quality zinc, the cathodes must contain less than 10 ppm lead. In order to reduce the lead contamination of the cathode, the lead anode must become coated with a protective layer of Pb02/Mn02. The formation of this layer may take as long as 30 - 60 days, during which time zinc production is substantially reduced and the cathodes are contaminated with lead. To improve the mechanical properties of Pb-Ag-anodes alloying elements such as calcium, strontium, barium and others are added. The production of cast lead-silver or lead-silver-calcium anodes often results in the formation of numerous holes, voids or laps in the anode surface that can initiate localized internal corrosion. Based on the experience as the major supplier of rolled anodes for copper electrowinning, RSR Technologies has developed an improved anode for zinc electrowinning. The anode consists of a rolled Pb- Ag-Ca-alloy with a controlled surface grain structure. It forms an adherent protective oxide coating within 2 - 3 days when placed in an electrowinning cell. The preferred calcium and silver contents of the alloy are 0.03 - 0.08 % and 0.3 - 0.4%, respectively. Rolling sheets significantly reduces the presence of internal porosity or laps. The lack of defects results in long anode life. The rolling also produces a uniform grain structure to which the corrosion product readily adheres, thus significantly reducing the conditioning period.

Jan 1, 2000

By John M. Rapkoch

In the continuing search for copper matte converting methods, commercially available and feasible choices remain Peirce-Smith Converters, Hoboken Converters, Mitsubishi Converting, Ausmelt converting, and Outokumpu/Kennecott Solid Matte Oxygen Converting (?Flash Converting?). While each alternative improves on Peirce-Smith Converters? limited fugitive gas capturing capability, the Peirce-Smith Converter is relatively easy and economic to operate and has an unmatched ability to accept valuable but difficult-to-handle material such as scrap anodes and purchased scrap copper. Recent experience with designing, building, and starting up an ISASMELT facility, applied in primary smelting of copper concentrates, has led the authors to speculate on how suitable the ISASMELT process would be for copper converting, given its low fugitive gas release and its ability to accept a variety of feed types. This paper reviews the potential metallurgical challenges posed by converting copper matte in an ISASMELT vessel and considers possible engineering and design challenges posed by the inclusion of this technology into a new or refurbished copper smelter.

Jan 1, 2006

By William J. Mallio

Substantial differences between in situ and conventional technology require that in situ ore grade be established for deposit as distinct from the total contained metal value. Establishing an in situ ore grade involves determining the fraction' of the contained metal that can be leached by the fluid. This depends on the proportion of the ore minerals that occur on fluid flow paths as defined by the permeability distribution. Mechanisms involved in the in situ mining of sulfides are: oxidation of the sulfur, solution of the metals, complexing of the released metals, and a transport to a recovery point. Metal ions may be delayed or lost due to inefficiencies in these pro-cess steps or by reactions of the metal ions in solution with the rock. These reactions can involve precipitation of new phases, exchange of the metals of the interest with Ca or Na in clays or zeolites, retention of metals in oxidized mineral grains, or secondary enrichment of other sulfides along the paths of the solution flow. The efficiency of solution of metals and potential loss or delay mechanisms are controlled by local equilibria (the Eh, pH conditions) present in different parts of the ore zone. Permeability distribution in the rock mass and the coincidence of ore minerais with flow channels must be determined before a deposit can be judged suitable for in situ mining. Laboratory studies indicate that the natural permeability system is dependent on the degree of cementation of veins by late generation hydrothermal activities. The major conclusions of the study are:, 1. Deposit selection is critical; suitable deposit types include deep lying sedimentary deposits, selected zones of porphyry systems and vein controlled hydrothermal deposits; 2. Adequate laboratory and geochemical analyses should be undertaken through quantitative petrographic study and permeability mapping; and 3. Economic incentives for in situ mining must consider limitations of recovery caused by inefficiencies in dissolution and transport associated with particular deposits.

Jan 1, 1981

By R. W. Lee

The first prototype plant using the Imperial Smelting Process commenced operation in 1950. It is timely therefore to review the developments that have occurred with the process over the past half-century. A major advantage claimed initially for the process was its ability simultaneously to recover zinc and lead from bulk concentrates. This has remained a fundamental advantage, but it has been extended by the increasing treatment of secondary materials containing zinc and lead. This has been facilitated by the development of hot briquetting and tuyere injection. These techniques and their impact on the technology of the operation will be described. The other major advantage claimed for the process was its potential to achieve new levels of productivity in the pyrometallurgical smelting of zinc. This has been realised with operating furnaces producing up to 400 t/d of zinc. The technical developments that have enabled this scale of operation will be reviewed.

Jan 1, 2000

By M. R. Barkhudarov

Semi-solid metal can be formed into useful products of near net shape and high quality. Use of this method has been limited, however, because of the difficulty of working with metal in the semi-solid state, which has strong shear rate, temperature and time-dependent properties. In this paper we describe a thixotropic model and apply it to the problem of small metal droplets impacting on a flat plate.

Jan 1, 1997

By Hal dun Kurama

In thus-study, Bigadic upper zone zeolitic tuff, which contains about 87% clinoptilolite was used as an ion exchanger for removal of Pb++, Cu++, Cd++ and Hg++ ions from wastewater. Bench scale experiments with two different glass columns, were carried out continuously under the closed/ open circuit conditions. Before ion exchange tests, zeolite samples were treated with NaCI (6ml/ min. and 42BV). The effects of particle size, bed volume, pH and flow rate on the ion exchange capacity were determined. Under the best operation conditions, the effect of initial influent solution concentration on ion exchange selectivity was tested. As a-result, it was found that the Bigadiç clinoptilolite had the following ion exchange capacities;

Jan 1, 1995

By J. Chen Kuriyama

One method to store hydrogen effectively involves the use of metal complexes such as the alkali-element aluminum hydrides. The hydriding/dehydriding properties of these materials depend on how to prepare them with different structures and microstructures. The present work focused on a high-energy ball milling technique to produce Ti-doped lithium tetrahydridoaluminate (LiA1H4) and lithium hexahydroalanate (Li3AIH6) powders with nanocrystallites. The phase structures and dehydriding/rehydriding characteristics were investigated by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, Brunauer-Emmett-Teller measurement, thermogravimetry, and differential scanning calorimetry. The mechanism of dehydrogenation and rehydrogenation was also examined by means of X-ray photoelectron spectroscopy (XPS). The results on the relation between the reversible hydrogen storage and catalysis function of the Ti-doped complex hydride indicate that both the homogenous distribution of Ti+AI nanoclusters and the Ti¬catalyst with Ti e> Ti3+ (Ti0/Ti2+/Ti3+) defect sites play important roles in optimizing the reversible hydrogen storage.

Jan 1, 2002

By Mark Jolly, Nasim Soleimanian

"During the last 20 years CFD (Computational Fluid Dynamics) has been used as a tool to aid furnace designers and manufacturers to improve energy efficiency and effectiveness of glass furnaces. However as the models are maturing the effect of feeding equipment used to push the raw material into the furnace has not been included in the process models. This paper investigates the effects of batch pattern in the melt space caused by charging equipment on the energy efficiency of the furnace focusing on the melting zone. A simple batch patterns sensitivity study has been performed using purpose built software (Glass Furnace Model-GFM). It is concluded that in order to further reduce the energy consumption of the furnace it is necessary to model the batch charging process in more detail to find more opportunities for improvement.Introduction Glass manufacturing is a conservative industry which applies to all the four major segments (float glass, container glass, fiberglass, and specialty glasses). Risks due to the high capital investment, very long service life of the furnaces, and the demand for high performance and quality from the outset translates into evolutionary progress rather than revolutionary. The main problem facing glass manufacturers are the financial cost of manufacture, its impact on the environment, and mounting pressure imposed by the authorities for greener manufacturing and reduction in emissions.The main energy intensive activities involved in continuous glass manufacturing are: the need for high temperature to create and maintain the viscous flow, homogenisation of glass melt (melt residence time), and maintaining the two to achieve continuous output of glass at the right quality. The high temperature and long duration of homogenisation has resulted in the design oflarge furnaces, which have high energy consumption, low specific performance, and high C02 emissions. As an example in the container glass sector the most efficient furnace has a specific primary energy consumption of 3.8 GJ /tonne of glass at a level of 50% cullet in the batch. Even very small improvements in efficiency by optimising operation would have a high impact [1-14]. Given the conservative nature of the industry and the costs involved in experimental data gathering, CFD modeling of the process has been used extensively during last two decades to not only improve our understanding of the process but also as a tool in predicting possible optimisation windows, e.g. Glass Furnace Model ( GFM), a commercially available piece of software that has been developed to optimise furnace operation."

Jan 1, 2013

By C. L. Lin

Multiphase, irregularly-shaped randomly-oriented PARGEN particles were grown to determine the breakage/liberation characteristics of such locked particles. The simulated locked particles were randomly broken to establish the liberation characteristics of the broken fragments. The progeny size distributions are consistent with Gilvarry's volume and surface flaw model for single particle breakage. The extent of liberation of both continuous and dispersed phases can be described from the conservation of interfacial area. In this regard the data can be normalized and liberation described for a wide range of dispersed phase grades and dispersion densities.

Jan 1, 1988