Search Documents

By H. Gene Wilson

Mobile Roof Supports (MRS) look similar to a longwall shield on crawler tracks. The MRS units offer a safe, productive method of extracting the 40% to 60% product left normally unrecovered in room and pillar mining. The units feature radio control, self-contained power units, crawler track drive, and a 600 ton yield. Cribbing and setting posts in retreat mining has been a necessary burden to production. The MRS reduces this burden. Long blocks of coal can be developed to further reduce move and tram time, thus increasing production. The MRS units have successful safety records. The workers are removed from the immediate fall area, and we feel back injuries have been reduced by the workers not setting posts. While MRS units have been damaged in falls, the other capital equipment has been unharmed. The MRS product line has undergone normal product improvement and evolution. Product evolution is seen in our development of machines for particular mine requirements. Through the continuing development of the MRS, Fletcher presents the coal industry with a safe, productive method of retreat mining with potential to develop new mining methods.

Jan 1, 1990

By M Nombe

Based on the analysis of a case study at POWELTON No.2 MINE, it was determined that mine stability problems had occurred due to floor softening. A fireclay (underclay) layer in the immediate floor was softening after coal extraction and failing under pillars load. The thickness of soft floor was considered as the governing factor in the determination of the magnitude of floor displacement. The effect of floor thickness on floor displacement was evaluated by creating seven models that were input into the LAMODEL program. The properties of the soft floor were determined from a bearing capacity test performed in the Mains close to the area where mine stability problems had occurred. Moisture increase was considered in the reduction of floor bearing strength. Various strain-softening properties were allocated to the materials representing the soft floor. The LOW GAP POWELTON No.2 MINE was modeled and LAMODEL program was used to determine stress and convergence on both the coal seam and the fireclay seam. The results of critical stress and convergence obtained from modeling were compared with the actual floor failure area in the mine.

Jan 1, 2002

By Fangting Dong

The broken rock zone (BRZ) and the tunnel support theory are investigated. The relationship between the BRZ and the related factors, the interaction between the BRZ and supports, and the function of supports are analyzed in detail based on the authors' underground observations and model taste. A summary of the application of the BRZ theory in the past is also presented.

Jan 1, 1988

By S. M. Matthews

The magnitude and orientation of the in situ stressfield has been determined as a key factor in controlling the stability of openings for both coal mine development and extraction. Monitoring of roadway and pillar behaviour in conjunction with numerical analysis has identified specific stress control measures that have been successfully applied to improve productivity in underground coal mining operations. The influence of the major horizontal stressfield on the stability of openings has been identified at a wide range of sites including mines in Australia, Britain, the USA, New Zealand and Japan. Stress mapping, stress measurement and stress monitoring techniques have been applied to define the in situ stress regime and, together with the correlation of measurements of rock deformation and rock reinforcement behaviour, has enabled appropriate stress control measures to be developed. Stress control measures for development headings have required the selection of roadway orientation, roadway sequencing, reinforcement density and pillar size. The monitoring of behaviour at a range of trial sites has confirmed significant improvements in development stability. Stress control measures for longwall extraction have required rational selection of longwall orientation and extraction direction. Where a mine layout design incorporating the optimum longwall layout design has not been possible, the use of sacrificial roadways has been successfully applied to protect key roadways from stress concentration effects. Comprehensive in situ monitoring of behaviour has been carried out to confirm the mechanisms involved.

Jan 1, 1992

By Alan A. Campoli

"Pumpable crib support for longwall gates and ventilation bleeder entries is becoming more prevalent in United States coal mines (Figure 1). The pumpable crib selection and spacing design has been greatly refined by the full-scale testing conducted at the National Institute for Occupational Safety and Health (NIOSH) Mine Roof Simulator. The peak load on 24-, 27-, 30-, and 36- inch diameter J-Cribs is, on average, 300, 400, 450, and 650 kips, respectively. Standard J-Cribs have useful deformation of approximately 8 inches. The maximum useful deformation can be extended to 18–20 inches with an exterior reinforcement layer or an interior double wall, for all four J-Crib diameters. J-Crib diameter is primarily limited by a maximum 4.5:1 height-to-diameter aspect ratio. Spacing is controlled by immediate roof stability, anticipated pillar deformation, and roof bolting practice. Approximately 500,000 J-Cribs have been successfully placed in 18 different United States longwall coal mines. The selection and spacing of the J-Crib utilized to date is summarized for each mine.IntroductionLongwall productivity and safety depend on ground stability in gate and ventilation bleeder entries. Numerous support technologies have been developed and employed in United States longwall mines since the 1990s to replace traditional wooden cribbing. Many, if not all, of these technologies have been evaluated at the NIOSH Pittsburgh Research Laboratory since the mid-1990s (Mucho, et al., 1999). The NIOSH Mine Roof Simulator has a 3,000-kip vertical load and 24-inch displacement capacity, which has facilitated in-depth analysis of complex multimaterial support technologies like the pumpable crib. The extreme cost and human exposure risk associated with modern longwall mining prevent the trial and error development that would have been required absent the Mine Roof Simulator research. As a direct result of this research, pumpable cribs are becoming a major component of the standing support industry, providing the peak capacity and extended deformation characteristics necessary for successful gate and bleeder support. Recent research by Zhang, et al. (2012) and others have defined the required performance characteristics."

Jan 1, 2015

By Yanfa Gao

Abstract In order to control and reduce ground subsidence due to coal mining, and to protect building, railway and other surface construction, a new subsidence control method is proposed. Ground subsidence is reduced by grouting bed separations in overlying strata with fine-coal ash. Engineering application tests have been performed for 5 years in Tangshan Coal Mine. Kailuan Group Corporation. China. The technology has been applied to 4 fully mechanized sublevel caving mining faces. Its effect in reducing subsidence has been significant. The technology including grouting engineering design method and ground subsidence prediction theory is introduced in detail. Keywords: overlying strata separation, multi-layer grouting, subsidence control

Jan 1, 2002

By Anthony T. Iannacchione

Longwall mining produces surface subsidence basins that affect streams by water diminution and contamination. These effects can ultimately impair the biological character of the plants and animal communities living in the streams. The combination of flow, water quality, and ecological effects threaten the environmental sustainability of longwall mining and, ultimately its social acceptability. Pennsylvania has developed new standards, released in 2005 and implemented in 2007, to help protect the commonwealth?s valuable streams from the detrimental effects of subsidence. These standards are aimed at eliminating environmental problems and will therefore help to make underground bituminous coal mining more sustainable. The engineering solutions necessary to comply with these standards are fundamentally affected by the geologic nature of coal-bearing strata, the existing in-situ stress conditions, and the ability of selected species to survive and adapt to changes in their environment caused by longwall coal mining subsidence. Needless to say, geologists, biologists, and engineers are all playing a pivotal role in developing prevention controls and recovery measures necessary to protect streams and sustain underground coal mining. The challenges facing scientists and engineers in sustaining the development of underground coal mining in Pennsylvania are examined through case studies. These challenges all arise from the subsidence effects of longwall mining. The key effects of subsidence, discussed through case studies, are: a) tension cracks, b) springs in headwater stream areas, c) stream gradients and subsidence basins, and d) stream compression ruptures and horizontal stress. All of these potential threats demonstrate the need for high-level scientific knowledge and innovative engineering solutions. One could argue that Pennsylvania?s stringent stream protection standards put the coal mining industry at a competitive disadvantage compared to other coal producing states. It is equally likely that compliance with these standards help to mitigate the effect of subsidence, thereby helping the coal industry achieve a sustainable future.

Jan 1, 2011

By John L. Ellenberger

The National Institute for Occupational Safety and Health (NIOSH) has continued the research role of the former U.S. Bureau of Mines to develop techniques that will reduce the hazards in the mining work place associated with coal bumps. Current research focuses on both analyzing historical seismic data from bump-prone operations and utilizing a mine-wide seismic network to investigate the exact strata failure mechanics associated with bump-prone geology. The anticipated outcome of this research will be reduced bump incidences through advanced engineering concepts and designs which implement the new understanding of strata behavior. The analysis of the historic seismic data consists of correlating observed mining seismicity with the geologic and geometric parameters at the sites. The primary seismic parameters are the timing, location and magnitude of a recorded seismic event. These parameters are correlated with such mining parameters as: the overburden, the size of the immediate gob, the size of the district gob area, etc. This detailed analysis of historical seismic data has provided an informative quantifiable relationship between many of the specific mining parameters and the induced seismicity. The second aspect of the coal bump research is the instrumentation of an appropriate field site to determine the main roof, floor, and gob behavior associated with hump behavior. The chosen field site is a deep-cover longwall mine with competent geology in a historically bump-prone area. The primary field instrumentation is a three-dimensional, full-waveform, seismic array with both surface and underground sensors surrounding an active multi-panel district. The purpose of this seismic array is to determine the timing, the exact location, and the mechanism (tensile fracture, bedding plane slip. etc.) of the failure of the strata surrounding the active and multi¬panel gobs. The preliminary results presented in this paper help to define the strata failure areas around the longwall panel.

Jan 1, 2000

By Adam Mackenzie, Dan Payne, Yass-Marie Rutty

"Historically, the Crinum mine has experienced significant falls of ground when longwall production slowed to prepare for recovery in weak roof areas. These conditions continue through the recovery process and result in both safety concerns and delays. When mine plans and exploration revealed that most of the mine's future longwall recoveries were located in weak roof areas, a decision was made to try pre-driven recovery roads as a solution to the problem. After completing eight pre-driven recovery roads with varying degrees of success and numerous lessons, the Crinum North mine now utilizes a modified Pre-driven Recovery Roadway (PDRR) to improve the longwall take-off process in weak roof areas. During mine development, a standard roadway is driven where the final recovery location of each longwall is planned. After the installation of secondary support, the PDRR is backfilled with a cement-flyash mix to provide support to the roof, and confinement to the ribs and floor of the roadway. The method has been refined over the last four years to provide greater strata stability and improved operational and safety performance compared with conventional take-offs at Crinum, and has resulted in a site record of longwall relocation in 11.5 days (pull mesh to picks in coal). This paper describes the evolution of the PDRRs from Crinum East to Crinum North, including lessons from initial attempts and changes to the secondary support regime, the operational approach during the final stages of retreat, the backfill strategy and plans for the future.INTRODUCTIONThe Crinum mine is the underground component of BHP Billiton Mitsubishi Alliance's (BMA) Gregory Crinum mine, located northeast of Emerald, Queensland (Figure 1).The Crinum mine has a history of roof control problems coming into and during longwall recoveries. Weak roof, combined with the slow mining, which is a consequence of preparing for equipment recovery, pulling mesh (which also creates tip-to-face issues), and the lengthy bolt-up process, often results in loss of immediate roof and subsequent roof falls. In fact, approximately 50% of the first 13 longwall recoveries (which were at depths of 180 to 200m) experienced roof fall delays, the longest of which took four months to mine the last pillar and recover the longwall. This recurring problem prompted the mine to investigate options to reduce or eliminate the problem."

Jan 1, 2016

By Joe Zelanko

In order to prevent roof fall accidents and injuries, U.S. underground coal mine operators must develop and implement effective roof control strategies. Various tools are available to assist engineers in developing designs. For example, criteria to address global stability issues (e.g., pillar stability) are well established in the U.S.; effective tools (e.g., empirical and numerical) are available to diagnose potential problems and avoid catastrophic failures. However, most miner injuries occur as a result of local instability (e.g., a roof fall in a single heading or a rib roll from a pillar corner). Hazard recognition and the availability of support plans suitable to those conditions are key to maintaining stability and safety on the working section.

Jan 1, 2011

By Nengxiong Xu

The WTZ coal mine is located adjacent to an auxiliary dam in P. R. China. The mining-induced ground movements are calculated using a 3-D numerical procedure based on the finite difference method (FDM) to judge whether the extraction of the coal seam will have a negative impact on the dam. First, the values of the rock mass mechanical parameters in the numerical model are estimated using the available literature that relates intact rock and discontinuity properties to rock mass parameters. Then, based on available surface subsidence monitoring data for an area in WTZ mine, the main mechanical parameters of coal and rock masses are calibrated by a back analysis procedure that combines an experimental design technique with numerical simulations. Then the reliability of these rock mass parameters is verified. Finally, according to the planned mining sequence, predictions of mining induced surface subsidence are computed in steps, and the boundary of the ground movement area of each step is determined. The nearest distance from the boundary of the surface movement area to the edge of the dam foundation was found to be about 1347 m. The maximum surface subsidence within the mining area turned out to be 2.7 m, and the maximum settlement point was found to be close to west-south corner of A2 mined area. These findings led to the conclusion that the coal seam mining would not cause dam damage.

Jan 1, 2013

By Zhaohui Wang, Jiachen Wang

"Effective surrounding rock control is a prerequisite for realizing safe mining in underground longwall faces. In the past three decades, longwall top-coal caving mining (LTCC) and single pass large height longwall mining (SPLL) found expanded usage in extracting thick coal seams in China. The two mining methods lead to large void space left behind the working face, which increase the difficulty of ground control. Longwall face failure is a common problem in underground mining, which is induced due to low strength and high fracture density of the coal seam. Moreover, the stiffness of main components included in the surrounding rock system also greatly influences longwall face instability. Correspondingly, the surrounding rock system is developed for LTCC and SPLL faces in this paper. Mechanical conditions for simultaneous balance of roof structure and longwall face are put forward by taking the stiffness of coal seam, roof strata, and hydraulic support into account. The safety factor of the longwall face is defined as the ratio between its ultimate bearing capacity and the load imposed on it. The influence of coal strength, stiffness of the coal seam, roof strata, and hydraulic support, as well as the movement of roof structure, are analyzed. Finally, the key elements dominating longwall face stability are identified for improving surrounding rock control effectiveness in LTCC and SPLL faces.INTRODUCTIONThe concentration of coal mining in China is gradually shifting to the west region, and there are a large number of thick coal seams in the newly formed coal mining area. Therefore, the surrounding rock control problems related to mining of thick coal seams will become the focus of research in the field of mining engineering in the future. There are two kinds of mining methods for thick coal seams in China, including single pass large height longwall mining (SPLL) and longwall top-coal caving mining (LTCC). Both methods can accomplish the goal of excavating the full thickness of thick coal seams at one time. SPLL mining benefits from the improvement of the development level of associated equipment. The appearance of large hydraulic supports and high power shearers ensure that the height protected by the hydraulic supports and the height of the sheared coal are the same as the coal thickness. LTCC mining benefits from mining technology advantages. The thick coal seam is divided into two sub-layers, and the working face is normally installed in the bottom layer, while the top coal is caved under the compressive forces due to mining. Therefore, there is a scraper conveyor at the front of the hydraulic support for transporting the sheared coal and another one at the tail for transporting caved top coal. Both SPLL and LTCC methods realize one-off recovery of thick coal seams."

Jan 1, 2018

By Thomas Barczak

Pumpable roof supports provide an alternative longwall tailgate roof support and have grown in usage during the past few years. Heintzmann Corporation has been installing pumpable roof supports at the RAG Resources Emerald Mine in western PA since 1998, where they have provided effective roof control in their longwall tailgates. Despite the success of these supports in this application, questions remain regarding critical design issues for optimizing the use of this support technology. The support loading profile is characterized by a high initial stiffness with peak loading occurring at less than one inch of convergence, followed by significant load shedding with a post failure capacity comparable to that of wood cribbing. Therefore, the key to optimizing the support utilization is to provide sufficient load density to prevent convergence from occurring beyond the peak loading capacity. This requires an understanding of how the supports interact with the ground conditions, hence measurement of the ground reaction curve. In order to obtain this information, pumpable roof supports were instrumented to measure support loading. Roof deformation and roof-to-floor convergence measurements in the vicinity of the instrumented supports were also made. The experimental parameters for the installation were the support spacing and water¬to-solids ratio of the grout, which controls the grout strength and ultimately the maximum capacity of the support. The study clearly shows that at this mine a 24-inch diameter support is fully capable of providing adequate ground control under depths of cover of 750 ft as only 50 pct of the available support capacity was utilized outby the longwall face. It was also shown that the 2.00 to 1 water¬solids ratio, despite providing a slightly softer support response, is sufficient for maintaining the same degree of roof control provided by the traditional 1.75 to 1 grout mix. The 10-ft spacing of the supports did not cause any ground control problems outby the face. However, inby the face the performance of the support is degraded once the peak capacity of the supports is exceeded. It appears that the large load shedding behavior, which is characteristic of this support following peak loading, allows the immediate roof to separate. When this happens, the support is unable to regain control of the roof in time to prevent failure of the immediate roof beam.

Jan 1, 2003

By Lawrence R. Artler

The North American Coal Corporation, its subsidiaries and other coal companies, have been mining the Pittsburgh #8 seam in Eastern Ohio for several decades. Underground mining by the "room and pillar" method, and more recently by longwall methods, have been practiced. This presentation deals with ground control problems and subsequent solutions to those problems for both mining methods. But first, let me briefly discuss some pertinent points about the geologic conditions of the coal seam near the southwest edge of the Pittsburgh Coal Basin. The Eastern Ohio region of the Pittsburgh Coal Basin is situated along the western edge of the unglaciated Allegheny Plateau. The local terrain is quite steep, with topographic relief of 430-500 feet being common. The coal thickness in the region ranges from 36"to 120", with the average being 60" in the areas being currently mined. Regional dip of the seam is toward the southeast in an amount of 10 to 40 feet per mile. A cross-section of the mineable seam generally consists of the main bench (60"), a rider coal (6"-12"), and a claystone parting (6"-12") for a total excavated height of 6-7 feet. Greater excavated height occurs where the fireclay floor is so soft and friable that movement of mechanical equipment breaks up the first 4-8 inches. Generally, the main bench and rider coal thin and become more variable toward the southwestern portion of the mining area. The rider coal also grades laterally into a coaly carbonaceous shale. In those areas where the roof coal can no longer be counted on to help support the immediate top, some of the main seam (6") is left to protect the overlying 8'-12' of mudstone/claystone strata. These strata are virtually non-bedded, highly slickensided units and are "hung in suspension" by roof bolts from a more competent limestone stratum above. These mudstone/claystone units are very susceptible to moisture and thus to the weathering cycles. The rider coal or 6" of the main bench is left in place to "seal" the mudstone/claystone units in Mains and Submains development. For many years, it was thought that the strength of the limestone member was detrimental in attempts to fully extract the seam by conventional means; however, longwall methods that have been more recently employed have broken the "myth" that the Redstone Limestone prevents full extraction of pillars.

Jan 1, 1984

By Aarao de Andrade Lima

Mechanical properties typical of coal are used in the comparisons of pillar strengths based on finite elements and the empirical equations of Holland-Gaddy, Salamon-Munro, Obert¬Duvall, and Bieniawski-PSU. A correlation among the strength parameters which are employed in the empirical equations, in Mohr-Coulomb and Hoek-Brown failure criteria is established. Emphasis is given to the important distinction between the mechanical properties of small rock specimens and those related to the rock mass. An elastoplastic version of Hoek-Brown criteria has been developed and implemented in a finite elements code. The strengths calculated using the empirical equations showed a good agreement when the ratio width by height of the pillars varied from I to 8, except for Holland-Gaddy equation which exhibited lower values. Under the hypothesis of associative perfect elastoplasticity used, pillar strength calculated using Mohr¬Coulomb yield criterion became excessively high for all the models having a pillar width by height ratio above 2. The finite elements solution based on Hoek-Brown criterion predicted strengths around fifty percent larger than Bieniawski-PSU equation when the pillars width by height ration varied from 3 to 8, showing good agreement below that range. It has been concluded that, under the hypothesis of percfect plasticity, stress analysis techniques may overestimate the strength of rock structures subjected to high confining stresses.

Jan 1, 1997

By Alan Campoli

The Eclipse System was developed by Minova USA Inc. formerly Fosroc Inc. to improve the performance of 5/8-inch deformed rebar fully grouted into a one inch borehole. An 1/8-inch offset bolt head combined with specially formulated Eclipse Lokset resin cartridge results in reduced gloving and increased mixing efficiency. The benefits of the Eclipse System have been demonstrated, under the supervision of MSHA, in Kentucky, West Virginia and Illinois coal mines in partnership with Excel Mining Systems, a leading roof bolt manufacturer. Over 100,000 units have been installed to date. Eclipse system bolts exposed during overcast construction at the Panther Mine of Cumberland Resources displayed an extremely well mixed, uniform resin anchorage over the entire bolt length.

Jan 1, 2003

By C. A. Vining, J. R. Nopola

"Evaporites, such as salt and potash, pose unique problems to ground-support designs not encountered in other rock types. Evaporites are subject to continual creep and no amount of ground support can successfully arrest this process. Common ground-support techniques that are useful for most rock types may reduce the effective life of bolts in evaporite mines and can create unseen hazards. A different approach to ground support must be applied to provide long-term support in areas where high creep rates are present. The goal of effective ground-support designs in these situations is not to contain the rock and prevent it from moving; rather, the ground-support design must be able to move along with the rock and contain any fully detached slabs until additional remediation measures can be undertaken. The most appropriate ground-support designs will consider both the expected movement of the rock and the duration that the area needs to remain accessible.INTRODUCTIONEvaporites, such as salt and potash, pose unique problems to ground-support designs not encountered in other rock types. The factors that must be considered in design stem from the deformation behavior of salt, which can fail in a brittle manner, akin to most rocks, but can also deform in a slow, ductile manner, resembling the stretching and elongation of steel. The deformation behavior of salt has been well established in technical circles where it has been studied for decades (Hardy and Langer, 1984). Much of the research in salt mechanics is related to repository science, specifically at the Waste Isolation Pilot Plant (WIPP) in southwest New Mexico. RESPEC has been continually involved in the WIPP from the initial design considerations (Gnirk, Grams, and Zeller, 1977) to the current day (Keffeler, 2016) and has been able to leverage cutting-edge research of salt mechanics into practical solutions for mining operators. While a detailed description of salt mechanics is not provided in this document, Fossum and Fredrich (2002) include a fine overview of salt mechanics. The following list paraphrases their chapter on basic facts about salt to provide some context for the reader unfamiliar with salt mechanics:"

Jan 1, 2018

By Jesse Puller, Ken Mills

"This paper describes the Australia, New Zealand Inflatable (ANZI) strain cell, its operation, and recent development for overcoring in exploration boreholes. The ANZI strain cell is an instrument system that uses the overcoring method of stress relief to determine the three-dimensional, in-situ stresses in rock. The instrument has been used successfully for over three decades in numerous underground mining and civil projects, but technical advances over the last decade or so have allowed the system to be deployed in surface exploration boreholes to greater depths than was previously possible. Recent development of a downhole electronic data logger, a wireline-enabled drilling system, and an instrument deployment system has simplified the process of obtaining three-dimensional overcore measurements at depths approaching 1km to a single shift operation.The capability to deploy ANZI strain cells in surface exploration boreholes represents a significant breakthrough for the design of underground mines and underground excavations generally. High-confidence characterisation of the in-situ stresses at the design stage provides the opportunity to design key infrastructure and mining systems to take advantage of the in-situ stress field from the outset before mining begins. Understanding the three-dimensional, in-situ stress field not only provides a measure of the magnitude and direction of loads acting within the rock mass, it also provides insight into the mechanics of all the various processes driving ground deformations, including which geological fault structures are at limiting equilibrium.INTRODUCTIONThe overcoring method of stress relief is one of the most direct methods for determining three-dimensional, in-situ stresses in rock. The Australia, New Zealand Inflatable (ANZI) strain cell combines overcoring with several other techniques to provide determinations of the three-dimensional, in-situ stress field and the properties of the rock and, importantly, provides an indication of how much confidence can be placed in the measurement. This paper describes the advances that have enabled overcoring of the ANZI strain cell in deep surface exploration boreholes and the development of various complementary techniques that build additional confidence in the determination of the in-situ stress."

Jan 1, 2018

By James H. Fletcher

Much data and experience has been accumulated, especially in the last 5 or 6 years, to show that modern roof trusses, both of the Birmingham type and the bolt-and-channel type, perform well to support certain kinds of coal mine roof. For some time now, roof trusses of the Birmingham type have been effective in controlling thick shale roof, which tends to sag and fall over a period of about eight weeks. These falls leave dame-shaped cavities which are reminiscent of the pressure arch theory of roof failure. Lately there has also been significant interest in supporting some longwall panel entries with channel and-bolt systems. These systems utilize two vertical center bolts and two 45 degree end bolts through a heavy gage channel. Both types of truss systems have long bolts, which require 8 to 9 Foot holes on a 45 degree angle, and point anchor resin bolts, which utilize a 2 or 3 foot rebar grouted in a thin annulus of polyester resin. Consequently, many coal mining people have been impressed with the very good anchorage characteristics and tensionability features of these systems. However, the same people have been proportionately dismayed to find that very often the most difficult part of introducing a trussing program to a mine is deciding on the machine specifications which determine the truss installation rate. The purpose of this paper is to indicate aspects of truss bolter design and use which are not shared by roofbolter design and its vertical pattern of bolts. Of the two types of drill units conventionally accepted, arm feed units and mast units, only one 15 judged suitable. While the arm feed unit offers low collapsed height with a long drill feed length, a great attribute for low seam use, it has not lent itself to being rolled over to a 45 degree angle. One reason for this inability is that many items which are conventionally mounted on the arm feed unit cannot be allowed to rotate with the unit. These items include drilling controls, tool Cray, lights, canopy or safety post, panic bar, and stab jack(s). If these items were independent of the arm feed drilling unit, they would have to be out of the way of the boom arms, links, and feed cylinder as the unit moves. To ease this problem, the arm feed unit can be made very short and even mounted across the machine. However, the resulting short feed length is undesirable. Several short drill steel extensions are required to drill a relatively long hole, making this procedure time-consuming as well as increasing the likelihood of drilling a crooked hole. Another reason for abandonment of the arm feed unit is that a very stiff drill guide (or "centralizer") is required to start the hole. Using the mast tilt control, the roof bolter operator will force the bit against the roof and will rotate the bit without feeding to cut sideways into the roof to form a hole face. Omission of this step often results in the skidding of the bit toward the rib. To date, no such sturdy drill guide has been designed for an arm feed drill unit. The mast style unit has been the most successful design for angle drilling. It is easily rolled over to a 45 degree angle or to 90 degrees and, on single head models, often has been made to roll through 180 degrees. The mast style is compact, in plain view and is easily fitted with heavy duty manual or hydraulically operated drill guides. It can be mounted directly on a machine chassis, or onto a swinging boom, or onto a slider arrangement in a broad variety of configurations which will accommodate controls, tool trays, stab and roof support jacks, lights, canopies, and panic bars. The only significant difficulty with mast drilling units occurs in lower mining heights when desirable low mast height is accompanied by undesirable short feed length. While the lead extension in the drill string can be as large as the mining height will allow, a short feed length will permit only the use of shorter middle extensions and drivers, and perhaps will. require the use of two different length wrenches. The associated problem is the relatively short distance from the drillhead to the drillguide. This distance is further shortened when raising the drillhead to get the bit to the roof. One might keep longer lead extensions on the machine; drill a vertical pocket for the bit, starting the angle hole at this pocket; or modify the mast. If the mast is made so that the distance from the drillhead to the drillguide remains constant while the mast extends, after which the drillhead travels up the mast, the shorter mast can be made to start the hole more easily. However, short teed length will still result in longer drilling time. It is obvious from these points that a proper choice of mast is simply the highest one which will be moved easily in the given mining height. This, of course, goes against the grain of most experienced coal mining people who realize that a relatively small decrease in mining height can create a problem correctable only with the purchase and installation of shorter masts. If the mining

Jan 1, 1982

By Benjamin Mirabile

"Current and emerging practices to ventilate longwall gobs are prompting increased design and analysis of standing support requirements related to longwall mining. Specifically, additional design methodologies are being employed to evaluate standing supports in the #2 entry of a 3-entry longwall system.Numerical modeling will be used to evaluate the performance of standing support in the #2 entry between gobs of longwalls in the Herrin No. 6 seam. The performance of standing support in the #2 entry will be evaluated based on the following: (1) The effectiveness of standing support in maintaining an open airway in the #2 entry; (2) The interaction of standing support in the #2 entry with standing support in the longwall tailgate; and (3) Loading conditions of longwall pillars. Initial numerical modeling activities are focused on evaluating the roof to floor convergence in the #2 Entry and using the ground reaction curve concept for support design.Numerical modeling indicates that, like standing support in tailgates, supports in the #2 entry require some type of yield mechanism to withstand initial uncontrolled convergence. Numerical modeling also suggests that support density can be lower than that used in a tailgate support application. The numerical models used for initial investigation of support performance in the #2 entry are limited in their ability to evaluate support performance. The magnitude of uncontrollable convergence can be estimated with LaModel software. Near-seam conditions have not been investigated in this research since the LaModel software does not have the ability to evaluate inelastic rock behavior.IntroductionDuring the past three decades, many researchers have investigated standing support performance in longwall tailgate entries. Very little attention was paid to the middle entry of a threeentry longwall gateroad. As longwalls retreated, no personnel would travel the #2 entry, and the entry was considered part of the longwall gob. In response to recent mine disasters, regulatory agencies and operators have devoted more attention to these entries. Prior to the Upper Big Branch mine disaster, little or no secondary support was applied in these entries. Unlike secondary support in longwall tailgates, there is little empirical knowledge or quantified research specifically applied to secondary support in the #2 entry. This paper outlines initial steps used to develop a design methodology for secondary support in the #2 entry."

Jan 1, 2015