Search Documents

By Kis M

The purpose of seismic control of blasting is to indicate the vibration magnitude or to eliminate the occurrence of vibration damage caused by blasting. At the Mining Research Institute in Hungary, a new method has been developed to determine the method of delay. Near the blasting site (within 100-200 meters), the peak value of the particle velocity is determined by calculation and also by measurement. In the calculations, the time error of the electric detonators is taken into consideration. During the test program, the results of the experimental blasts and the calculated data have shown good correlation. The method of calculation helps the operator eliminate vibration damage, while the greatest quantity of charge can be detonated.

Jan 1, 1979

By Karl Dufresne

Blasting in geothermally high temperature ground and/or extremely reactive ground is an increasing common challenge for surface and underground mines. Many current PETN based non-electric and electronic detonators have manufacturer published in-hole temperature limits ranging from 55°C to 65°C (131°F to 150°F) and prescribed in-hole residence times on the order of days. When confronting blasthole temperatures above the manufacturer published limits, operations may request site-specific guidance and qualification for use. The advised safe loading window for in-hole PETN based detonators is often too short to be practicable for production blasting. To overcome limitations of PETN based initiation systems, surface mines with high temperature ground and/or reactive ground are known to load blastholes with a qualified high temperature bulk emulsion that are top primed with a cartridge of temperature qualified detonator sensitive emulsion plus an RDX detonating cord downline. As there is no in-hole delay detonator in this system, blasthole timing is accomplished with surface delays. Although this system is safe, top priming and surface delaying does influence floor quality and top size fragmentation, and safe loading windows times reduce blast block size and increase blasting frequency. The DynaEnergetics IGNEO high temperature electronic initiation system is rated for in-hole use in ground up to 150°C (302°F) for 48 hours. The detonator consists of a high strength detonator with an HMX base charge and thermally resistant downline. To make up a primer, the detonator is inserted into a booster charge assembly that is fitted with a small HMX shape charge. This high energy primer is designed to be compatible and reliable for firing bulk emulsions, including those with high percentages of urea inhibition to combat reactive ground. Up to 1000 detonators may be programmed in 1ms increments up to 1500ms. The system is controlled by a digital firing panel that can be used with either a wired or wireless trigger. The system enables high temperature and/or reactive ground sites to utilize in-hole delay initiation and realize the associated performance benefits. An underground mine in Western USA has several areas in their development heading with very high temperature, in view of this, they decided to use the IGNEO detonators in order to evaluate the effectiveness and performance of the system.

Jan 21, 2025

By Tom BoBo, Seth Gering, Jeff Loeb

Presenting a D&B feedback loop built on a well-designed blast, proven fragmentation analysis and blast monitoring solutions, underpinned by technology that not only increases profit from every blast, but also increases a mine’s purchasing power over one of the most expensive part of the process – explosives.

Feb 1, 2020

By L. Chaves

In rock blasting, due to numerous factors, both controllable and uncontrollable, the execution rarely meets the planning. The powder factor is an important KPI for blasting since it represents the amount of explosive used to fragment the rock, therefore it depends on the rock mass characteristics and may be influenced by factors such as weathering and drilling quality. The blasts at the Serra Sul mine, S11D project, are usually big blasts and the high productivity is a challenge for maintaining the quality of the whole drill and blast process. It is important to know the contributions of each of the most common influencing factors of the powder factor to direct the efforts to the improvement of the process. A buildup model is presented to evaluate the contributions of five influencing factors to evaluate the planed x executed powder factor. The factors considered in the model are the average hole depth, the amount of hole/blasted volume, the stemming and decking length, the linear charge weight, and the density of the explosive used. The build-up may be applied for both individual blasts and for overall view of the blasts in a period. A case study is presented with the application of the model for the monthly powder factor analysis at Serra Sul mine has contributed to direct efforts to enhance drilling quality and preservation of the drilled holes.

Jan 1, 2024

By R Yang, P D. Katsabanis, W F. Bawden

Understanding the mechanisms which are taking place during the propagation of a stress wave generated by an explosive charge is of high importance in the detection, characterization and prediction of blast induced damage to the rock. Vibrations caused by the detonation of an explosive are suspected to contribute significantly to the extension of the damage zone. Vibration monitoring close to a blasthole is a relatively new field of research, the hindrance being the scarcity of transducers capable of sustaining extreme accelerations without damage. This paper focuses on the vibration monitoring aspect of a blast induced damage study; the experiment took place at Queen's test site and was meant to record near-field vibration as close as 1 m from 100 mm diameter blastholes.

Jan 1, 1993

By Pierre DePasquale, Ricardo Chavez

Lowering of quarry energy consumption participates to answer both environmental and financial issues. The “EE-Quarry” European project, supported by the European Commission (EE stands for Energy Efficient), develops a new and highly effective modelling and monitoring Energy Management System technique to improve Energy Efficiency and move to a low CO2 emission rate in the nonmetallic mineral industry. Within this global quarry project, blast design, as the first link in the chain, has to be optimized in order to satisfy requirements of downstream operations. The authors have been developing and implementing an operational methodology using continuous field measurements and field adaptation methods for blast design. It drives the drilling and blasting work, aiming at a more energy efficient and environmentally friendly operation. Based upon actual local conditions (rock-mass assessment, face geometry, borehole deviations, etc.), blast patterns are optimized through a specific hole-by-hole blast design software. It provides a better and more consistent energy distribution, to achieve a better rock fragmentation, while avoiding explosive overconsumption. The software also calculates total energy inputs and the drilling and blasting contribution to Greenhouse Effect. Coupled with methodical fieldwork and variable density explosives, it has been leading to a real reduction in energy costs and greenhouse gas emissions. As the project is now reaching its final stage, demonstrations were conducted in various quarries around Europe. Several simulations were carried out and compared to the site data, in order to propose enhancements for the different phases (extraction, loading, hauling, crushing and transport) while bearing in mind the environmental impact of the quarry. This blasting methodology allows to assess the carbon footprint of drilling and blasting in conjunction with the downstream operations, thus to evaluate the global carbon footprint of quarrying. Copyright ©

Jan 1, 2015

By Erik Nygaard

Ammonium nitrate (AN) is the main ingredient in most industrial explosives, but it is estimated that as much as 80-90% of the global annual production is used as fertilizer [14, 25]. Over the last years AN has been involved in several accidents and used in criminal bomb making. Therefore authorities and legislators worldwide have given it special attention. This paper is divided into three parts: • The first part will focus on the accidents with AN that have occurred over the last years and possible scenarios based on official investigations. • The second part covers safety and security related issues. • The third part will summarize new legislation that is coming both within European Union (EU) and also on a global scale.

Jan 1, 2006

By Paul Worsey, Braden Lusk

Differences exist between public perception of construction blasting and quarry blasting. In general, people are able to tolerate short term inconveniences much better than long term ones. The paper focuses on the public perception of quarry blasting in St. Charles County, MO. This expanding urban environment has seen new legislation targeting preexisting quarry operations that have been in place for many years. A survey was made comprising interviews conducted to gauge perceptions of persons with varying demographics. Interviews covered topics involved with quarry blasting and its reporting methods. The purpose of the interviews was to determine public perception of blasting and how best to report results of vibration measurements. The use of different, less technically complicated measurement scales for vibration and airblast was considered as an alternative reporting system. The question for the industry is, “Has our past haste in adopting complex scientific scales and units been detrimental to us?” In other words, are we reporting the correct things? For airblast, the decibel scale was evaluated against millibar in the public eye. Peak Particle Velocity was also compared to that for displacement. Current legislation in the county is based on complaint levels rather than damage criteria. The complaints most likely not only come from ignorance to the affects of blasting on structures, but also sparse understanding of the units used to report these affects. The past practice of treading softly as an industry has been proven to be a poor choice, and education of the public as well as lawmakers on all levels is necessary. The Mississippi Valley Chapter of ISEE has begun to conduct seminars to this end. One educational seminar has taken place for officials and lawmakers in the St. Louis area, and others are in the planning stages. The focus of this paper is to gauge perception of the damage criteria reported today, and locate focal points for future education of the public in rapidly expanding suburban environments.

Jan 1, 2005

By Jonathan Zimmerling, Rob Alkins

The model of waves emanating from a blast hole proposed by Heelan, and further developed by Blair and Minchinton, provides an approximation of particle motion in an isotropic, continuous and homogenous medium caused by a cylindrical pressure source. Previous work in the literature shows that the shapes of the peak strain and peak particle velocity contours generated by this model are influenced by priming location. This paper presents the results of experimental investigations into the effects of priming position in an explosive column and the resulting shape of the surrounding stress and particle velocity fields. Fifteen emulsion charges were detonated in a limestone quarry, of which eight were bottom primed and seven top primed. The charges were fully confined, with no breakout to any surface. Particle velocity was monitored using tri-axial sensors coupled to the rock using cement, and pressure sensors were placed in water filled boreholes for fourteen of the experiments. Statistically significant differences in peak pressure for bottom and top primed shots were observed. Blair and Minchinton developed two pressure source functions, one of which is scaled using the charge weight scaling law. New models of the explosive pressure source are developed and compared to those found in the literature. These models are directly calibrated by predicting the peak velocities achieved at the known locations of the velocity sensors, then minimizing the residual sum of squares between the predicted and observed peak vibration values. Due to the complexity of the model the residual sum of squares cannot be minimized using standard non-linear optimization techniques, so a stochastic, agent based global optimization method is employed. Models are then cross validated by comparing the relative predicted differences in stress between bottom and top priming position to the observed differences.

Jan 1, 2013

By T. Palangio

Most blasters wouldn’t think of initiating a shot without a seismograph to record vibration and air blast results. Some might even measure the velocity of detonation but few surprisingly record the event on video, photo document loading conditions or take pictures before and after the shot. This paper discusses digital imaging, the equipment, methods, techniques and information that can be learned from digital pictures taken in the field during blasting operations. The guy who said “a picture is worth a thousand words” probably understated it.

Jan 1, 2008

By S D. Cummings

"CRACKS CONCERN CORPORATION" Was the headline on the front page of the Terre Haute Tribune Star, March 1994. Having spent several years following up on blast-induced damage allegations made this article especially interesting. Knowing that there were no operating mines within 30 miles of this newly built, yet to be occupied building, also made the reading more enjoyable. The article went on to read, "Vigo County school officials have asked architects to find out whether some cracks in walls at the new school are due to NORMAL settling or if they indicate serious structural problems." It is obvious that if there were a mine within "Feeling" distance, blasting and the operator would have immediately become suspect as at least one of the potential causes. More alarming is that the investigation may have stopped there.

Jan 1, 1995

By Alan R. Gadberry

To resolve drilling and blasting problems, rather than treating symptoms and allowing problems to grow, the mine operator needs to change the way he operates. When a mine operator discovers a drilling and blasting result that he doesn't like, it is easy for him to think of that disappointing result as a problem. More often than not, however, that result is only a symptom of a problem, and the real, underlying problem cause can be seen when the operator looks in the mirror. Symptoms and problems relating to drilling and blasting are resolved when the mine operator makes appropriate changes in the way he manages his operations.

Jan 1, 1985

By Edward J. Walter

Our modern technology is provided with a unique but flexible power tool in the use of explosives. A by-product of explosives usage is vibration or elastic deformation of the earth which is annoying to the ordinary person and can be damaging to structures. The problem is not new, it is more than fifty years old. Adequate vibration standards have been developed so that blasting programs can be properly planned and safely executed. Changes in our social culture have somewhat changed the emphasis in blasting vibration from damage considerations to the much lower level of citizen annoyance. Vibration codes based on this level will be highly restrictive and prohibitively costly. Cooperation is urged between operators, community officials, agencies at all levels,and consultants to see to the development of sound realistic vibration codes.

Jan 1, 1975

By Robert B. Hopler

Hercules Incorporated has designed, developed, and begun introducing a new non-electric delay blasting cap system which is radically different from anything presently available. This system, called Hercudet™, utilizes no wires or detonating cord. Instead, each cap has two plastic tubes attached to it. These tubes contain no coating or other materials other than dry nitrogen to extend storage life. In use, after connecting the tubes together with external sleeve connectors, the circuit is checked with a specially designed tester. When the blast area is cleared, the circuit is filled with a gas consisting of an automatically proportioned mixture of fuel and oxidizer gases. When the circuit is fully charged the gas is initiated by special means within the Hercudet™ blaster. The reaction that then travels throughout the circuit has no distruptive effect on the tubing, and virtually no noise is produced.

Jan 1, 1975

By Peter Bellairs, Anthony Bubb

The Porgera Gold Mine is located at an altitude of 3000m in the central highlands of Papua New Guinea some 600 km Northwest of Port Moresby the capital city. Access to the mine is via a five hour trip on an unsealed road from Mount Hagen the nearest regional centre or 40 minutes via air. The mine operates on a fly in - fly out basis and currently produces ore from both opencut and underground operations with the former providing the bulk of the mill feed. Opencut mining utilises conventional truck / shovel, drill and blast methods on both 10 metre and 14 metre bench heights with the larger benches being restricted to the stripping areas. This paper presents the strategy used and the results of a blast optimisation process in the opencut that was a joint effort between the mine personnel and the explosives manufacturer/supplier.

Jan 1, 1997

By Peter Moser

The average annual consumption of raw minerals in Europe is 10 ton per person. About 50 % is produced by blasting. For a population of 450 million (including the population from the countries of the new member states) this makes 2.25 billion tons of blasted rock, 80 % being building industry aggregates and industrial minerals. In aggregate quarries 10-15 % of the rock blasted can’t be sold, as the material is too fine, i.e. smaller than 4 mm. This ‘fines problem’ is worse in the quarries of limestone and cement producers where up to 30 % of the material is useless. Thus about 450 million tons of useless rock fines are produced and put on waste dumps every year, i.e. 1 ton/person. This problem is addressed by the research project LESS FINES - “Less Fines production in aggregate and industrial minerals industry” which is funded by the European Union under the project contract G1RD-CT-2000-00438. The project consortium, formed of nine partners from 5 EU countries, works on the following two main research subjects: 1. The determination of the natural breakage behavior (NBC) of the rock mass, which is defined as the particle size distribution curve for a certain rock mass with the maximum uniformity and thus for a given maximum particle size that fragmentation curve which gives the minimum amount of unusable fine material. The comparison between the NBC and an actual blast fragmentation curve allows to quantify the fines reduction potential. 2. The adaptation of explosives properties, charging techniques and timing in order to produce only the minimum, inherently unavoidable percentage of fines. With about 15 full time working persons the project is estimated to be one of the largest blast related research activities in Europe at the time of the project period. The project is coordinated by the Department of Mining Engineering& Mineral Economics of the University of Leoben.

Jan 1, 2004

By H Leonard Mangum, Victor C. Bryan, Dan McCutchen

Recently there has been an unprecedented marketing effort to promote the advantages of various non-electric initiation systems. This activity has probably been influenced by a major manufacturer's decision to discontinue electric detonator production. Subsequently, distributors of explosive materials, rather than introducing new electric detonator brands, are emphasizing the use of existing non-electric systems. In many cases, such methods fill the need of explosive users in the quarry industry. However, the use of any initiation system should be based on performance, rather than the bent of the market or convenience to the supplier. This analysis is an evaluation of the performance of non-electric systems with emphasis on double trunk line and loop (redundant), as compared to precise electric detonators in use by Martin Marietta. Redundant non-electric detonators, even though more costly, offer the most reliable method of non-electric initiation. However, state-of-the-art precise electric detonators give the best overall performance, except in an environment involving extraneous electricity.

Jan 1, 1990

By Paul V. Sterk, James Wieser

Mining in underground situations requires constant change due to changing ore bodies and economics. The Homestake Mine in its 122 years of existence has gone through numerous changes due to these factors. Recent sustained low prices in gold and ore bodies that are smaller or within mined out areas have forced the mine to reevaluate how these ore blocks will be mined. This paper will describe the design, drilling, and blasting of a complex ore block using the blind raise uphole bulk mining method.

Jan 1, 1999

By R. Sibley, K. Perry, E. McCorkle, M. Coy

Black powder has been used in fireworks since the 10 th century in China. To this day, black powder still has a variety of uses, including fireworks, and remains relatively unchanged. Black powder is used in the firework shell to help produce the effect and in the lift charge to propel the shell skyward. The performance of fireworks shells used in displays varies greatly. In fireworks shells, there are two different black powder charges that differ in construction based on the desired performance of the shell. The two charges consist of the lift charge and the break charge. The lift charge is the first to fire and propels the shell out of the mortar. The break charge is the second to fire and is initiated after a delay from the lift charge; its purpose is to burst the shells effect over the desired area of the sky. The lift charge provides the shell with its initial velocity by pressurizing the mortar below the shell body. The pressurization process is violent and occurs in fractions of a second. The purpose of these experiments are to better understand the pressures sustained in fireworks mortars during the firing process. Mortars and shells vary by size and weight. Pressures in each mortar were monitored at various heights along the mortar to provide a pressure profile during shell lift. A high-speed camera was used to measure shell exit velocity near the mortar’s muzzle. This information was correlated with the size and weight of shells and their respective lift charges

Jan 1, 2024

By Bilegt Batbold, Bayu Saputra, Chris Batten

The ability to fire multiple blasts simultaneously can provide significant benefits to any open pit mining operation. Reduced blast-related downtime by reducing blast events can increase equipment utilization and maximize material movement. Significant sequencing benefits can also be delivered, associated with reduced equipment relocation. This paper describes the work completed in partnership between Orica and Oyu Tolgoi to successfully demonstrate that combined production-trim and midsplit blasting could be implemented successfully while successfully managing the risk of increased damage to the final walls. The paper details the methodology used to assess key performance measures linked to final wall damage and compares the performance between the following blasting methods. • Free face trim blasting vs. combined production-trim blasting • Presplit blasting vs. midsplit blasting. The results of the initial trial blasts are presented, along with the method agreed by the key site stakeholders for ongoing application. The method used to keep the risk of final wall damage to an acceptable level is explained, along with the benefits delivered to Oyu Tolgoi operations associated with the initial 12 months of application.

Jan 21, 2025