Search Documents

By Bruce B. Redpath, Thomas E. Ricketts

Scaling laws commonly used for describing or predicting blast motions generated by conventional arrays of blastholes are dimensionally incorrect. The scaling of distance by the cube root of charge weight is correct only for spherical charges, and scaling by the square root of charge weight is incorrect for any charge configuration, although both approaches may result in empirically useful formulas for a limited range of charge sizes. Analysis of motions generated by a large set of underground blasts shows that scaling distance by the square root of the linear charge density, which is dimensionally correct for a cylindrical borehole, yields much more consistent results than the traditional scaling rules. Further, this scaling law is valid right up to the free face of the burden. A significant result of this work is that the peak particle velocity for an array of blastholes is primarily dependent on blasthole diameter and not on total charge weight or maximum explosive weight per delay, which are the commonly used parameters for scaling seismic amplitudes generated by conventional blasting arrays.

Jan 1, 1987

By D T. Froedge

The state of Kentucky is making some changes in it's blasting program namely instituting a training program for blasters and instituting a new classification of blaster titled "Class A Kentucky Blaster". These changes will take place within the next year and are felt to be of great interest and benefit to those in the blasting industry.

Jan 1, 1978

By Jason M. Ryan, T Michael LeBlanc, John H. Heilig

"Drill trajectory deviation is a recurring problem in vertical retreat stoping operations. As a result of thisdeviation, 60 kilogram (165 millimetre diameter) and 103 kilogram (203 millimetre diameter) explosive charges are routinely detonated beyond ore/waste contact zones. Consequently, there follows a reduction in finished stope wall stability and an increase in ore dilution."

Jan 1, 1996

By Yang Ruilin

Bulk gassing technology is a growing trend in the commercial explosive industry. The gassed bulk products produced differ from microballooned bulk products or cartridged products. It is easy to know the loaded or in-hole density for microballooned bulk products or cartridged products, whereas it is not as straight forward to know the m-hole density for gassed bulk emulsions. The loaded density is one of the key parameters affecting explosive performance and therefore it is important to have a field technique to monitor the in-hole properties of gassed bulk products in order to accurately predict the blast performance and to ensure efficient use of the products.

Jan 1, 1999

By Ray Heater, Qian Liu, Alan Bauer

The channel effect is a phenomenon that takes place with decoupling explosive charges; an air shock wave propagating ahead of the detonation wave in the annular space around the explosive charge compresses the charge so that the process of detonation is modified and even stopped. For commercial explosives, such as AN/FO slurries and emulsions, the channel effect causes partial detonation under certain conditions. To simulate and evaluate the phenomenon, a hydrodynamic model was developed based on the assumption that the pre-shock wave is produced by Mach reflection at the tube walls. Based on instrumented experimental studies with the above explosives in diameters ranging from 25 to 90 mm in pipe sizes ranging from 35 to 127 mm, it has been possible to demonstrate that a criterion for failure based on a critical impulse concept fits the experimental data well. Critical impulse values for the various explosives tested are presented along with the necessary correlations between charge and borehole diameter required to produce this.

Jan 1, 1988

Increasingly specialized blasting needs require that the explosive energy available in a borehole be reliably known for representative blasting conditions. The underwater test, when properly performed, can yield such information and thus provide a reliable rating of explosives in terms of energy release. This paper reiterates the stringent experimental conditions to be satisfied, and data analysis and interpretation techniques to be followed to achieve this. This is supported by detailed experimental studies involving select parameters in both detonator and booster sensitive explosive compositions. The paper also illustrates the inadvisability of equating blasting performance with the commonly calculated energy values.

Jan 1, 2000

By Gerald R. Coonan

Early in the open session of the 1979 SEE Fifth Conference panel discussion, someone asked a question of the panel concerning the future intent of the Office of Surface Mining and the regulatory limits established for ground vibration and air blast. The "gist" of the question was: "What assurances do we have that OSM will not promulgate a limit of 0.5 inch per second ground vibration, or some other number within the next two years or so."

Jan 1, 1979

By Philip H. Porter

Ammonium nitrate blasting agents continue to be the work-horse of the explosives industry. The versatile, low-cost, anfo products, whether packaged, poured, or bulk, continue to produce superior results for the explosive consumer who understands their limitations and capabilities.

Jan 1, 1984

By Clarence Zink

The need for continual process improvement and innovation to reduce operating costs in the mining industry extends to the first significant encounter all production miners have with the rock: drilling blastholes. Material and design advances alone have greatly increased the productivity of today's tricone blasthole bit over bits used just a few years ago. Significant additional operating savings are being realized by utilizing improved air practices on blasthole drills, and by selecting drilling equipment designed to provide optimum air volume and pressure at the blasthole bit.

Jan 1, 1997

By Doug Wathen, Philip M. E Thomas

The City of Fort Myers needed to replace a 40-year old 42-inch storm sewer line in downtown Fort Myers with a new 54-inch line to accommodate population growth. The old line had to be kept operational while a new line was installed. the contractor spent two months using a drop ball, a hoe ram, and large rippers trying to break the three to four feet of rock that needed to be removed to accommodate the new pipe. Mechanical trenching was considered but was proven to be overly expensive. On very short notice, Ireco of Florida was asked to design and execute a blasting procedure that would allow this project to proceed. Nearby buildings were over 80 years old, three of them containing antique shops specializing in glass antiquities with attorney offices above them. High water table compounded problems with a 20-year old steel water main and clay drainage pipe 15 feet from the new sewer line. Holes had to be drilled within six inches of the edge of the existing pipe to four feet below the pipe on either side of the pipe and blasted. No interruption in the sewer line flow was to be tolerated.

Jan 1, 1996

By Mark S. Stagg, Rolfe E. Otterness, Stephen Rholl

The Bureau of Mines is engaged in research to develop and test high explosive fracturing and rubblization techniques that will enhance ore body permeability and thus increase recovery during in situ mining. The natural permeability of many ore bodies is too low to allow successful in-place leaching. These deposits could be profitably mined if flow rates of leach solutions could be increased. Blasting represents a potentially low-cost and effective permeability enhancement technique.

Jan 1, 1991

By Kenichiro Yamamoto, Masaharu Murakami, Toshio Matsuzawa, Yoshiyuki Ikeda

In a series of tests, we examined the dynamic shock resistance of Emulsion Explosive in water and compared it with that of Dynamite and Slurry Explosives. Both the distance between donor and acceptor charges and the delay initiation timing of the acceptor charges were varied. The resistance to dynamic shock varied with the properties of the explosive. In the case of emulsion explosives, there seems to be a certain proportional relationship between the critical detonation distance and the delay initiation timing. Some blasting results with emulsion explosives are described.

Jan 1, 1983

By Dale L. Ramsey

Blasters in the field for years have been faced with the task of plotting blast locations for future reference and calculating scaled distances or seismograph placement from maps,aerial photo's etc.'With the constellation fully operational, GPS provides a satellite signal transmitted to a ground receiver which will display the desired coordinate positioning worldwide, 24 hours a day in any kind of weather conditions. There are a variety of GPS receivers available with varying levels of accuracy. The field trials of a handheld navigational quality instrument for plotting blast and seismograph locations along with other necessary industry related data is the basis of this paper.

Jan 1, 1994

By C A. "Hawk" Hanger

"The paper that will be presented is an in-depth study of sequential blasting using standardnon-electric shock tube down hole timing along with surface M.S. connector timing.Included also will be a discussion on the advantages in fragmentation, digability, oredilution' and ground vibration versus the common practice of row by row blasting. Alongwith the written presentation, several visual illustrations will be included. The visuals willrefine the actual direction and predicted movement of the shot involved."

Jan 1, 1993

By Yessica Idrogo, Omar Gómez, Francisco Pérez, Eduardo Yrigoyen

Rock blasting is one of the most important operations in the mining cycle value chain, requiring optimized explosives mixtures to get good results. A new and better strategy, and that which is discussed herein, is to design a new emulsion explosive, which can provide improved characteristics and benefits over and above general types of emulsion explosives. It is therefore critical that this product is functional over a wide range of conditions

Jan 1, 2019

By Keith Pucalik

One of the more important duties of the vibration consultant is to evaluate allegations of blasting damage by neighboring property owners. Unfortunately, the consultant is generally faced with having never seen the project, or preparing for litigation three or more years after blasting was completed. Under these circumstances, he must rely totally on blaster's logs and other contemporaneous records to conduct a meaningful evaluation.

Jan 1, 1990

By R Mancini

Explosive charge action on the medium is intrinsically dynamic (fast rising and fast vanishing). On the contrary, information available on rock strength is drawn from static behaviour, and it's commonly used to characterise the rock, even in blasting problems.

Jan 1, 1995

By Michael David Wilkins, Paul N. Worsey

Little research has been published on stemming blast holes, particularly what happens during the process. Previous work has concentrated on the performance of the inert material to find the best way to seal the hole and retain the explosive energy, at the exclusion of determining what happens during the loading and stemming process.

Jan 1, 1998

By John W. Brown

During the summer of 1994 the mining industry experienced numerous accidents involving blasting related incidents. The Tri-State Chapter of Explosives Engineers planned a meeting to discuss three of these accidents.

Jan 1, 1995

By Anatoliy Yegupov, Vladimir I. Samoylov, Alexandr V. Startshinov

Access difficulties and unique climatic and geotechnical conditions of mineral deposits in permafrost in the Russian Northeast require specific approaches in the selection and use of explosives.

Jan 1, 1992