Search Documents

By P. Fawell, C. Castillo, C. Ihle

"The need to reduce fresh water consumption has pushed many Chilean mining companies to utilize seawater obtained from distant locations. At the same time, increasing amounts of fine particles in copper tailings raise new operational challenges, in particular, the thickening and transport of tailings featuring significant fine fractions, which are predominantly clays. In the present paper, we study the role of salinity – using seawater and NaCl – on the flocculation efficiency of copper sulphide tailings to which kaolinite was added. To mimic the water recovery stage in thickeners, flocculation has been induced in jar tests and the corresponding aggregate size distribution has been estimated from chord length distribution data obtained using a focused beam reflectance measurement (FBRM) probe, at various mean turbulence intensities. Results show that for constant flocculant dosing, a measurable influence of the salt on the resulting aggregation exists. For each case, resulting optimal turbulence levels are also reported, a particularly interesting feature when comparing flocculation efficiency of the coarse and fine fraction. INTRODUCTION The concentration of copper minerals through comminution and flotation is intensive in the use of fresh water. The need to reduce the consumption of fresh water and the environmental standards associated with increasingly demanding mining operations have driven improvements in the techniques of recovering water from tailings. The challenges are even greater when required to treat minerals with high clay contents. In Chile, kaolinite is one of the most important clays to consider due to its abundance in the tailings from many operations. The most common and highest throughput unit operation in the mining industry for the recovery of water from tailings is gravity thickening, with sedimentation of fine particles assisted by flocculation. Flocculation is the process of forming aggregates by contacting the suspended particles with a flocculant. The flocculant is typically a water-soluble synthetic long-chain polymer, where copolymers of acrylamide and sodium acrylate are the most common types used in the Chilean mining industry. The aggregation mechanism includes the following key steps: (1) flocculant distribution through the suspended particles, (2) flocculant adsorption onto particle surfaces, and (3) collisions between particles leading to polymer bridging to form aggregates, but concurrently (4) breakage of aggregates becomes a factor under prolonged shear (Gregory, 1988)."

Jan 1, 2018

By N. Acarkan

Beneficiation of the pyrite concentrate of the Kastomonu-Küre (Northern Turkey) copper ore seems to be attractive due to its high Cu, Co, and Zn contents. Pyrite concentrate were used in the experimental studies. Cu, Co, and Zn were recovered from the concentrate by the sulphatizing roasting, leaching and the precipitation using H2S. Sulphatizing roasting experiments were carried out in a rotary furnace and the optimal roasting conditions were found to be at 650°C roasting temperature and 3.0 h roasting period and addition of Na2SO4 of 3 % for the concentrate containing 0.58% Cu, 0.22% Co, and 0.04% Zn. Then, the roasted product was repeatedly leached with 10 g/L H2SO4 solution. Optimal conditions were found to be 60 oC leaching temperature, 2 h leaching period, and 30% pulp density. Leaching efficiencies for Cu and Co were over 99 %. The valuable metals in the pregnant solution were selectively precipitated by H2S as sulfides. Selective precipitation of Cu, Zn, Co was achieved by adjusting the pH and the temperature of the leach solution. Final metal recoveries of 99.20% Cu, 99.40% Co, and 95.60% Zn were attained. The precipitated sulphides are marketable products. Roasting gases with their 15% SO2 content are suitable for the production of H2SO4 and the leach residues can be integrated with the iron ore processing plant as they contain 57.50 % Fe, 17.70% gangue (SiO2, CaO, etc.), 0.04% S, and 0.06% non-ferrous metals.

Jan 1, 2014

By Christopher Robben, Alexander Mosser

"X-ray transmission (XRT) sorting has been introduced into the minerals industry in 2006 and has found various applications in diamonds, industrial minerals and metal ore processing since. The technology offers planar projections of the atomic density of single particles similar to the principle known from airport scanners, but being capable of treating up to 150tph per metre working width. In 2010, a pilot operation using a belt-type sensor-based sorter went into production at the Mittersill mine to treat the fraction 16-28mm. After an optimisation phase, the results were superseding expectations and therefore in 2012 a bigger production plant was set up. Two XRT-based sorters are parallel in operation since. One is treating the fine fraction 16-30mm while the other one is treating the coarser fraction 30-60mm after the secondary crushing stage. The XRT sorters are operated with the objective to reject barren waste before it enters the mill and flotation plant. 105,000tpa of waste material are rejected per year and can be sold as aggregate for road construction. This means that about 22% of the run-of-mine ore are rejected at an early stage with a waste reject grade lower than 0.03wt%WO3. The installation has not only led to lower specific operating costs but also led to reduced tailings disposal in an environmentally sensitive area. This allows the mine to reduce its headgrade which allows for a longer mine life. Alternatively it is possible to produce more tungsten concentrate, which is delivered to the smelter. This article will introduce the technological principle of XRT-based sorting and will discuss the flow-sheet of the Mittersill mine. Experiences that have led to the current plant design are described as well as the impact it has on the operation."

Jan 1, 2014

By Sergey Ulianov, Arkady Senchenko, Alexey Shvets, Arkady Bakotin

"This paper is devoted to ultrafine grinding of processing products. This process allows one to include into operation complex ores which earlier were considered as inefficient and economically inadvisable to treat. Fine dissemination of valuable component often does not allow its liberation via standard grinding in ball mills, and therefore requires modern methods of ultrafine grinding (UFG). An example of successful ultrafine grinding usage is its application for crude flotation concentrates regrinding before cleaner flotation stages. A problem often arises with a commercial copper concentrate production in the course of copper ore flotation. Crude flotation concentrate regrinding in a ball mill does not provide for good liberation of the material before cleaner stages. UFG application allows one to get commercial copper concentrate with copper grade of 20% and higher. Another example of ultrafine grinding application is its usage for highly refractory pyrite product received after gold-lead scavenger flotation of polymetallic ore. Earlier this product treatment was economically inefficient. At current application of ultrafine grinding down to 85% minus 20 µm and subsequent gravity processing it is possible to pass major part of gold (73.4%) into concentrate. The constraining factor for UFG application in processing may be the chemical activation of minerals. In the result of this, flotation selectivity may decrease. Therefore ultrafine grinding application extends the areas of efficient usage of metallurgical processes. New technologies allow increasing the level of valuable metals recovery."

Jan 1, 2014

By Amir Hajizadeh Omran, Mehdi Irannajad, Sima Mohammadnejad, Fardis Nakhaei

"This study presents an experimental program performed to investigate the effects of flotation variables including gas flow rate, froth depth, slurry solids percent, frother/collector dosage and pH on the froth bubble size during desulfurization of an iron ore. These conditions were varied using a central composite design (CCD). Image analysis techniques have been developed and used successfully to characterize the froth bubble size. Results of the CCD experiments showed that the flotation variables have different effects on the froth bubble size. The froth height, air flowrate, pH and solid content had the most important influence on the froth bubble size. The interaction between the collector-frother, pH-collector, frother-air flowrate, solid content-froth height, pH-froth height and solid content-pH were also significant. Process state can be accurately deduced from the froth surface appearance, providing a convenient way to quantify the parameters as a function of the process control. INTRODUCTION Flotation processes are subjected to a wide variety of process disturbances, some of which are made by the change in mineral features and others to variation in operating procedures. Feed and air flow rates, densities, size distributions and shapes of particles, surface properties, and reagent dosages and compositions can all change, often with significant effect on the performance of the plant (Moolman et al., 1996a). Flotation process efficiency is governed by the wettability of the solid as well as the surface tension at the liquid-gas. Both of these properties are influenced by operational conditions encountering in a flotation process. The structure of froths developed on the pulp surfaces of flotation cells has a remarkable effect on both the grade and recovery of minerals in the concentrate (Shean and Cilliers, 2011)."

Jan 1, 2018

By Shuji Owada, Shinya Suzuki, Chiharu Tokoro, Daisuke Haraguchi, Sayaka Izawa

"Coprecipitation with ferrihydrite has been one of the major treatment method for As(V) removal from wastewater such as acid mine drainage. We already confirmed coprecipitation of As(V) with ferrihydrite consists of two kinds of mechanism; one is two dimensional As(V) uptake to the surface of ferrihydrite by surface complexation and another is three dimensional As(V) uptake into ferrihydrite by surface precipitation. We also already confirmed As(V) adsorption process by ferrihydrite could be quantitatively evaluated by original surface complexation model with parameter values reported by Dzombak and Morel. However, As(V) coprecipitation process couldn’t quantitatively be represented by only the original model. In this study, construction and calculation using surface precipitation model were attempted for As(V) coprecipitation treatment with ferrihydrite. In the surface precipitation model, precipitation was described by the formation of solid compound between ferrihydrite and ferric arsenate. Activity of these precipitates was determined by surface precipitation ratio of FeAsO4(s) obtained experimentally from XANES analyses. Solubility products of surface precipitation of FeAsO4(s) (Ksp_FeAsO4(suf.)) were determined by fitting to sorption densities and surface precipitation ratio in each condition. The values of Ksp_FeAsO4(suf.) were determined 10-7.7 at pH5 and 10-10.2 at pH7, respectively. Based on the obtained Ksp_FeAsO4(suf.) value, As(V) removal and isotherm were calculated for As(V) co-precipitation treatment using surface precipitation model. Good agreement between experimental and calculated values was observed. These results were suggested that the quantitative prediction of As(V) co-precipitation treatment was possible if Ksp_FeAsO4(suf.) value was estimated experimentally."

Jan 1, 2014

By B. McFadzean, S. Geldenhuys

"Dynamic froth stability tests have found widespread application to quantify froth performance. However, little to no attention has been given to scale parameters in the performance of these measurements. One of the most frequently changing scale parameters in the laboratory scale is the column diameter as this directly influences the amount of material needed for testing. Four different column diameters (50, 100, 200 and 300 mm) were used for this study. Column diameter experiments were done on an industrial scale by means of manual tracking of froth growth versus time. An increase in measured dynamic stability was seen with increasing froth column diameter, which reached a limiting value at large column sizes. It is thought that this behaviour is controlled by the differences in drainage rates of the bulk froth compared to froth in contact with the wall. The column diameter required to represent full-scale froth stability is proposed. A ratio of column surface area to total bubble surface area was used to correct for different column diameters.INTRODUCTIONThe froth phase in flotation contributes significantly to the overall performance of the process (Zanin, et al., 2009). Numerous parameters have been investigated to quantify froth performance, most notably froth recovery (Feteris, et al., 1987; Seaman, et al., 2004; Vera, et al., 1999). Experimentally gathering data to determine froth recovery is challenging and for this reason froth stability has been highlighted as a possible alternative.Froth/foam stability is defined as the time of persistence of the froth/foam and is affected by numerous factors, such as: drainage of the liquid in the lamellae (gravitational and capillary), viscosity at the bubble surface, thickness of the electrical double layer and gas diffusion through liquid films caused by pressure differences between bubbles (Aktas, et al., 2008; Beneventi, et al., 2001). It is well documented in both froth and foam literature that froth/foam stability will heavily influence the performance and appearance of the froth/foam phase (Ata, 2012; Farrokhpay, 2011; Weaire, et al., 2005). Experimentally this has been explicitly proven as an increase in froth stability, characterised by water recovery, usually results in an increase in both valuable mineral and solids recovery (Wiese, et al., 2011; Banford, et al., 1998)."

Jan 1, 2018

Froth flotation is an industrial process commonly used for the separation of mineral particles. Bubbles sparged in a pulp collect and carry hydrophobic particles to the top layer of a flotation cell, the froth zone. There is a strong correlation between the stability of the froth phase and the flux of solids. However, flotation units placed in series operate, as a whole, in a non-steady state regime with the concentration of particle decreasing from one cell to the next resulting in a decrease in froth stability, which can compromise the recovery of valuables. Organic chemical reagents, frothers, are generally added to prevent fine bubbles from coalescing and to increase the stability of the froth phase. Frothers represent the second largest group of mining chemicals. It is crucial to understand the resulting properties of the frother on the froth phase in order to select the most suitable reagent for a particular operation. The bubble coalescence dynamic of three different surfactants, 1-pentanol, poly (propylene glycol), and tri (propylene glycol) methyl ether, were investigated in this study. In the first stage, the stabilisation mechanism of bubbles in a solution of surfactant was investigated using a specifically designed experimental setup. The coalescence behaviour of bubble pairs was recorded using high-speed video imaging in which information such as the coalescence time and the deformation of the resultant bubble upon coalescence could be extracted. The results were then compared between the different surfactants for several concentrations. It is shown in a study that the coalescence time increases with surfactant concentration until the Gibbs-Marangoni effect is suppressed by bulk diffusion. Conversely, the oscillation of the resultant bubble was found to be affected only at concentrations at which the film is saturated. The implications of the effects of surfactant type and concentration on the coalescence time and bubble oscillation in froth flotation are discussed. Keywords: froth flotation, frother, bubble coalescence

Sep 1, 2012

By X. L. Wang

Hydrothermal method was applied in the preparation of calcium sulfate whiskers in airtight re-actor using gypsum as primary materials. The optimum conditions of preparation are as follows: pH value 9.8~10.1, concentration 5%, material size 18.1µm, which were determined by the analysis of the diameter of CaSO4 whiskers through SEM. On these conditions a product of ultrafine CaSO4 whiskers with diameter of 0.19µm and aspect ratio of 98 is obtained. Ultrafine CaSO4 whiskers with different concentrations, modified by titanate NDZ-401, were added into polypropylene as intensifier and composites of Ultrafine CaSO4 whiskers/ polypropylene were prepared by melting-extruding method. Mechanical performance of the composites was tested and surface morphology of the composites was observed by SEM. The results indicated that impact notched izod of the composites was enhanced by 49.5% compared with pure polypropylene when 10.0% Ultrafine CaSO4 whiskers were added into polypropylene and toughening effect was very remarkable. Dispersion behaviour and interface phenomenon of Ultrafine CaSO4 whiskers in polypropylene matrix were investigated by SEM. The results indicated that Dispersion performance of Ultrafine CaSO4 whiskers modified by titanate NDZ-401 in polypropylene matrix is good, which improved mechanical performance of composites to some extent.

Jan 1, 2014

Pure camsellite samples were prepared through crushing, sorting and grinding the high-grade iron-containing camsellite ores from Fengcheng, Liaoning, China. The flotation behaviour of camsellite was studied via a systematic investigation of camsellite flotation re-covery changes as a function of choices and dosages of collectors and depressants at different slurry pH. The results showed that at pH 8.5 to 9.5, the recovery of camsellite reached the maximum at 90%~93.5% using dodecylamine as the collector, while under the same condition a recovery of 84%~86% could be achieved with sodium oleate. The adsorption of dodecylamine was not affected by the addition of sodium hexametaphosphate, but the adsorption of sodium oleate could be significantly depressed. This implied that sodium metahexaphosphate could be used as an effective depressant for the other associated minerals during the dodecylamine flotation of camsellite. When starch was used as the depressant, the flotation of camsellite by sodium oleate was almost completely depressed in the alkaline conditions. Significant depressions were also observed when calcium chloride was added in the camsellite-sodium oleate system. The higher the slurry pH is, the stronger the depression. Zeta potential measurements indicated that the flotation was mainly initiated by the electrostatic adsorption of the collector on camsellite. X-ray photoelectron spectrometer (XPS) analysis showed that the adsorption was originated from the electrostatic attraction between the N atom in dode-cylamine and B atom in camsellite. Dodecylamine had a higher coverage on the camsellite surface than sodium oleate.

Jan 1, 2014

By M. Saghaeian, R. Hejazi, H. Abedini, M. Zare

Water recovery in mineral processing plants is one of the most important subjects because water supply is a critical matter economically and environmentally, especially in desert areas. In this paper, the filtration behaviour of two iron ore tailing sample has been investigated using laboratory scale vacuum and pressure filtration units. These samples including tailing from Sirjan and Zarand concentrate production plants with the d80 of 94 and 41 micron, respectively. The results show that by using vacuum filtration the cake moisture content of Sirjan sample would be about 24%. But the filtration time is too long and vacuum belt filter cannot be used in industrial scale. Adding about 40 g/ton of flocculant would decrease the filtration time by about 30% and make the vacuum belt filter appropriate for dewatering of this sample. For Zarand tailing sample, the vacuum filtration would produce a wet cake by about 31% moisture content. Filtration time is too long and adding flocculant would not improve the results very much. So pressure filtration must be used for dewatering of this sample. The results of laboratory tests show that using pressure filter would reduce the cake moisture content to 21%. The filtration time is logical, so this process can be used for Zarand tailing dewatering.

Jan 1, 2014

By A. V. Golovanov, A. V. Mihailova

"NPO RIVS employs complex approach to engineering and design of the new facilities in close cooperation of Mining, Research, Hydrometallurgy, Design, Construction, Power Supply, Automation, Production and other departments. General Design Contractor (and then General Contractor) is directly involved in geological exploration, engineering surveys, floatability studies, feasibility study of process solutions and construction options. It delivers greenfield project and guarantee its efficient performance in future. Shiralgin is a small gold and copper deposit, gold average grade is 4.7 g/t. RIVS departments have studied ore floatability, developed process procedures for design and performed pilot testing. Construction of integrated plant including ore crushing and grinding, flotation and hydrometallurgy units with Dore gold production of 5 000 thousand tons ore per year (66.7 t/h) is recognized as economically viable. The technology used of separate dry stockpiling of flotation tailings and cyanidation tailings. Water circuit for concentration and hydrometallurgy is separated, too. Process design was performed based on BIM software like Autodesk Revit, Civil 3D, Rocscience slide using process procedures developed by RIVS Research units. Engineers provided modeling of primary crushing unit, coarse ore storage, main building (including grinding, flotation, thickening, filtration, loading, hydrometallurgy), tailings thickening unit, building for reagent storage and conditioning, tailings pond for dry stockpiling of flotation tailings and cyanidation tailings, sedimentation ponds, laboratories, infrastructure including Administration building and camp. Payback period is 3.5 years. 3D model of facility is currently stored at the State Agency of Geology and Mineral Resources affiliated to the Government of the Kyrgyz Republic.INTRODUCTION The Kyrgyz Republic has substantial potential of mineral resources including gold ores. Mining industry actively develops and involves international investors. Inventory includes 42 deposits (Figure 1) that have reserves of 616.4 t [1] of gold. The Kyrgyz Republic takes the third place in gold mining among CIS countries after Russia and Uzbekistan by producing up to 20 t annually."

Jan 1, 2018

By V. F. Bannikov, A. P. Kozlov

"The purpose of this study was to develop a theoretical and technology framework for designing new combined technologies for processing tailings containing non-ferrous and noble metals using dry separation. The main goals of the study were: identifying the distribution patterns of valuable components in various fractions in dry separation processes; examining the patterns identified for different types of non-ferrous and noble metal tailings; developing a theoretical and technology foundation for the development of innovative technologies for the efficient processing of tailings with minimal process water consumption. To examine the possibility of efficient recovery of valuable components from refractory tailings using dry separation, an experimental laboratory unit was designed and built, composed of novel or modified lab equipment: plasma unit for increasing the magnetic susceptibility of Fe - containing minerals; magnetic separator supporting isodynamic and polygradient fields; pneumatic separator for the dry separation of finely dispersed mineral mixtures; dielectric separator using the resonant frequency of the electric field. The laboratory unit supports various modifications and combinations of the lab equipment. The experimental studies led to the development of a unified process scheme for lab tests of mature and non-ferrous smelter tailings using dry separation methods.INTRODUCTION The huge amount of waste from mining and processing of mineral resources Russia inherited from the extensive use of mineral resources in the Soviet Union and amount of waste continue to grow. Often the content of valuable non - ferrous, rare and noble metals in waste exceeds the balance contents in natural ores of the developed deposits. The availability of a rich scientific reserve for the creation highly effective innovative technologies for waste processing determines the necessity of the acceleration in the resolution of problems of the complex assessment, capitalization and involvement in the processing of technogenic resources in Russia (Chanturiya and Kozlov, 2014.)."

Jan 1, 2018

By S. S. Yu

In this paper, the producing process of using V2O3 as raw material to obtain vanadium nitride was analyzed through the means of thermodynamic. The analysis shows that conversion follows the principle of reduction step by step in the conversion process of V2O3. The temperature of the reaction system has prominent influence on the nitrogen content of products, and the reaction is very sensitive to temperature. As raising temperature, the fine grain structure of the nitrides is more evident, and the grain size of nitrides increases. At 1703K, the nitrogen content of the products tended to be constant after soaking over 3 hours.

Jan 1, 2014

By Massimiliano Zanin, William Skinner, Keith Quast

With the scarcity of fresh potable water on mining sites, particularly those in arid and remote regions, the use of sea water is being contemplated and actually used at a number of mineral concentrators worldwide. The use of sea water, with its associated high dissolved solids content and ionic strength will affect all aspects of processing (e.g. frothing and froth stability, buffering capacity for pH control, solubility of minerals and corrosion of media and equipment). Selective depression of pyrite is more difficult in sea water due to the increased lime addition to achieve a high pH. This results in a reduction in molybdenite recovery. The use of grinding media with various chromium contents and its effect on subsequent Cu and Mo flotation has been investigated in the current study, with both grinding and flotation testing conducted in artificial sea water. Pulp chemistry (pH, Eh and DO) have been logged during grinding, and flotation testing was conducted on subsequent slurries. The flotation results show that the system is remarkably robust and able to cope with wide ranges of pulp chemistry parameters. The effects of artificial sea water on the surfaces of minerals during grinding have been examined using X-Ray Photoelectron Spectroscopy

Jan 1, 2014

High flotation of iron sulfide minerals at high pH values in copper ores is mainly due to the activation of these minerals by copper species dissolved from copper sulfide minerals during grinding. Several methods have been tested to reduce this copper activation during grinding and therefore to depress iron sulfide flotation. They include grinding the minerals at high pH values or with a less reactive medium such as high chrome, and addition of a thiol collector or copper complexant during grinding. The efficacy of these methods in the flotation of a copper ore was tested against more common methods of depression of iron sulfide flotation. The mechanism of iron sulfide depression in these methods was also investigated.

Jan 1, 2014

By R. D. van der Weijden, W. F. C. van Wageningen

"Copper(II) can be recovered or removed from acidic copper sulfate solutions as cuprite or metallic copper powder by reduction with carbohydrates (van der Weijden et al., 2001, 2002). In order to make this process suitable for a commercial scale pipe reactor, process conditions and reactor configuration need to guarantee proper throughput of the dilute suspension. This is where crystal engineering also comes into view. Copper powder characteristics, such as size and shape of particles, influence the tendency to adhere to reactor walls and to agglomerate, which in turn influence the throughput. Furthermore, separation, drying, packaging and product quality, are dependent on the powder characteristics.In this paper the effect of both chemical and physical parameters on the shape and size of particles were systematically studied in a number of autoclave experiments. These parameters include mixing, Cu(II) concentration, pH, temperature, seeding, use of additives and reactor materials. Additionally, Monte Carlo simulations of copper growth inside a Kenics static mixer were made. Results show that the use of additives, and the use of static mixers influence particle characteristics the most."

Jan 1, 2003

By M. Pelser, C Aldrich

"The presence of calcium and magnesium in the hydrometallurgical processing of base metals, results in a number of process difficulties. These problems range from the contamination of the final product (where the final product is a precipitate) to high energy consumptions and large bleed streams during electrowinning. Calcium poses an additional problem in sulphate solutions owing to the low solubility of its sulphate salts. This can easily lead to a process stream that is supersaturated with calcium sulphate, resulting in unwanted solids formation within the process equipment.Several processes are reviewed for the control of calcium and magnesium. Of these, fluoride precipitation was selected for experimental investigation. This method involves the addition of a soluble fluoride to precipitate CaF2 and MgF2. The experiments showed high selectivity for calcium and magnesium over the base metals. The experiments also showed magnesium precipitation to dominate for calcium to magnesium molar ratios greater than 1:3.To avoid the domination of magnesium precipitation, a flow sheet is proposed whereby only a portion of the base metal stream is subjected to fluoride precipitation. For the precipitation, a 10% excess of ammonium fluoride is used to remove the maximum amount of calcium and magnesium. After precipitation and solid-liquid separation the split-stream is returned to reduce the overall calcium and magnesium concentration of the base metal stream."

Jan 1, 2003

By E. A. Bekchurina, Yu. P. Morozov

"This paper presents the results of a study of the concentration of flotation froths in tapered chutes. The tests were conducted on lab and full-scale plants, and the results obtained were mathematically processed. The kinetics of monophase recovery from a stationary flotation froth, hydrodynamics of froth flows traveling in a tapered chute were investigated. The effect was studied of the mass fraction of the valuable component in the chute feed, yield of the chute’s overflow, and chute design on the concentration performance. Processing of the collected data revealed the general laws of the process and allowed to develop a technique for modeling concentration of the flotation froths of sulphide copper ore in a tapered chute to predict the performance without testing. It was found that concentration in tapered chutes allows to obtain products that are comparable in quality with froths after one or several cleaner flotation stages.INTRODUCTIONThe present production expansion rates require continuous improvement in the grade of flotation concentrates, while the grade of the mineral feed is constantly deteriorating. This leads to a significant complication of flotation flowcharts. Flowcharts become multi-staged with multiple cleaner flotations, negatively affecting the production costs.In recent years, researchers are paying close attention to the processes occurring in the froth layer in the flotation cells. Improving the concentrate grade is facilitated by secondary concentration of minerals in the froth layer, which consists in fixing the hydrophobic particles released as a result of the coalescence of the bubbles of the upper layer when moving downward at the liquid-gas interface of the froth layer. In this case, the released hydrophilic particles, trapped in the froth layer as a result of mechanical removal, migrate from the froth together with the liquid phase."

Jan 1, 2018

By A. V. Rasskazova

"The oxidized and mixed ores are processed by heap leaching. Primary ores with high gold content are floated. In recent years mining of primary ores with the low gold content (up to 4 ppm) has increased. Extraction of gold from these ores by floatation is technologically ineffective. Gravity concentration is ineffective for fine gold particles because of their floatability. The research objective was assessment of the viability of processing gold-bearing ore with combined gravitational and hydrometallurgical methods and testing of recovery of metals from a gold-copper oxidized ore chloride-hypochlorite leaching solution. The advantage of chloride-hypochlorite lixiviant is the low cost of reagents which is produced by the electrochemical synthesis of NaCl solution with the addition of HCl. The adsorption of chlorine compounds by a mineral matrix and its ability to oxidize the refractory ore components and allows for the application of chloride-hypochlorite systems for gold recovery for both oxidized and primary ores. The complexity and problem in using a gold–chloride system is the strong adsorption of gold–chloride complexes onto mineral surfaces, such as goethite, quartz, and alumina. In preliminary testing, gold recovery from gravity circuit gold bearing concentrates processed by agitation leaching in chloride-hypochlorite solution, gold recovery has reached up 82% after 4 hours of leaching. Chloride-hypochlorite leaching of copper-gold oxidized ore with preliminary processing by sulfuric acid provided for 94 % gold recovery to solution. Understanding of ecological hazard of cyanides is the motive power of researches in the field of search non-cyanic chemistries to provide for technologically and economically effective solvents of gold. Soluble compounds of chlorine with a suitable oxidizer are one of the alternatives to cyanides. Basic researches of gold extraction by chloride-hypochlorite solution have shown high rates of gold recovery.INTRODUCTION Because of the continued and growing environmental concern for the use of cyanide for gold processing, interest for the use of non-cyanide lixiviants, especially with halides has renewed recently (Tran et al., 2001; Ferron et al., 2003; Bhaghalha, 2007). Leaching solutions based on halides (chloride, bromide and iodide) are viable alternative to cyanide (Kwang et al., 2008). The major disadvantage of the chlorine–chloride system is the high reactivity of chlorine in reaction with sulfide and gangue carbonate minerals. It is believed that only high grade materials may be treated by chlorine–chloride systems economically (Baghalha, 2007). Another important problem of the application of gold–chloride complex is that it tends to be rather unstable and may re-precipitate upon contact with a reductant, such as sulfidic minerals of ore. It is well known that Au(III)–chloride hydrolysis species are strongly adsorbed by goethite, quartz, and alumina (Machfsky et al., 1991). To minimize adsorption of gold–chloro complexes, it works best to minimize the adsorption time."

Jan 1, 2018