Search Documents

By Bengt H. Fetlenius

The "Pile Prediction Event" at the ASCE GeoInstitute's Deep Foundation Conference in February 2002 involved prediction of drivability and capacity of three 14m long, 324mm diameter, closed-toe pipe piles driven into loose to compact fine sand to slightly silty sand. Predictors were provided the results of two soil borings and three cone penetrometer tests, as well as type and model of hammer to be used for the pile driving. A total of 33 persons submitted predictions. As to penetration resistance distribution, many predictions were far below actually observed values. As to capacity in compression, the predicted values ranged from 270KN through 2,340KN with a mean of 1,070KN. As to capacity in tension, the predicted values ranged from 100KN through 1,650KN. The maximum load applied to the compression pile in the static loading test was 1,25OKN, at which no more reaction load was available. The reaction system for the tension test failed early in the test. CAPWAP analysis on End-of-Driving blows showed capacities at the end of the driving for the push and pull piles of 670KN, and 710KN, respectively. No restrike tests were made. Additional CPT soundings indicate that the pile driving had densified the soil. Static analysis and calculations from the CPT indicated that capacities ranged from 1,000KN through 2,000KN. The paper presents the data and discusses the various methods of determining pile capacity and addresses influence of set-up Lessons useful for future similar events are indicated.

Jan 1, 2004

By Scott Webster

Dynamic pile Monitoring Services (DMS) have been used for testing of offshore piles for several decades. However, most of this testing was to measure hammer performance and pile stresses rather than pile capacity or soil resistance. As the need for more economical solutions for foundation support increases, the use of DMS has provided a better means of evaluating in-place pile capacity for offshore structures, and therefore a method of determining pile acceptance. The authors have been involved in several offshore projects where DMS has been the primary source of data for acceptance of the driven pile foundations. The use of DMS for evaluation of offshore foundations requires considerations quite different from land applications and these considerations are often necessary for the careful and thorough analysis of the collected data in nearly real time for determination of pile acceptance. Case Method capacity estimates are often of little use due to the non-uniform cross sections of the foundation piles and their deep penetrations. Therefore, capacity assessments should be made using CAPWAP which is a signal matching program whose utility and reliability has been proven on thousands of projects every year, both on land and offshore. Depending upon the soil conditions at a given location, capacity assessment after soil setup effects may be necessary. In addition, tension capacity is often critical when pile refusal occurs significantly before the design pile penetration depth. Evaluation of uplift capacity can be accomplished by a CAPWAP analysis, which results in a total capacity prediction and its shaft resistance component. The use of hydraulic hammers for driving of these piles also adds the requirement of controlling hammer energy such that over-stressing of the pile is avoided. The calculation of non-axial stresses such as bending or eccentric stresses may also be involved in order to prevent pile damage.

Jan 1, 2010

By Vijay Kumar, Serhat Baycan, Karsten Beckhans

For the deep foundation of podium and tower of the Kuala Lumpur City Centre, BAUER (MALAYSIA) SDN. BHD. constructed 225 bored piles with diameter range of 2.0 to 2.5 m. In order to comply with the depth requirement of the design, for planning purposes and preparation for site, the drilling equipment was required to achieve a maximum drilling depth of 150 m. Actual piles constructed on site were deeper than 120 m. These dimensions caused superlative challenges which included but were not limited to; controlling the open hole stability over time with polymer, installing 70-ton heavy steel cages, pouring up to 550 m³ concrete continuously, in conjunction with installation of kingposts into workable, fresh concrete. The piling works were executed with a BG 72, the biggest drilling rig globally available, and the stringent verticality of the pile bore holes which required approval prior to cage installation. For verification of verticality, Bauer’s patented Drilling Inclination System was successfully used.

Nov 1, 2022

By Amanda R. Parry, Chris R. Pray

Predicting and modeling the soil structure interaction of laterally loaded piles with significant unbraced lengths is one of the challenges faced in designing many waterfront structures. Designers often rely on pile specific design software to calculate forces in an embedded pile and then couple that with either a structural design software to capture the behavior of the rest of the structure or use potentially overly conservative assumptions to omit modelling the piles entirely. Given that some projects have hundreds of piles coupled with hundreds of loading conditions, the shuttling of results from the structural analysis software into the pile analysis software can become cumbersome, difficult to track and manage, and prone to user input errors. An alternative approach recently used on two large marine infrastructure projects consisted of calibrating a structural analysis software to replicate the resultant outputs from a software developed specifically for pile analysis. This calibration was done using thoughtfully placed springs along a pile modeled in the structural analysis software to replicate the soil-structure interaction of the piles. The focus of this paper will be on the methodology used to calibrate the two software programs and an evaluation of the results which showed close agreement. Based on the two case studies, calibrating a generic finite element analysis software via this method should be considered as a reasonable and time saving design approach for pile-supported structures.

Sep 8, 2021

By Renzo D. Verastegui, Michael Law, Sitotaw Y. Fantaye, Alfredas Daugiala

"When completed, 520 Park Avenue will amend the Manhattan skyline and be one of the most prestigious high-rise towers in New York City. The 52-story condominium building is located on a 60 ft by 100 ft lot (18.3 m by 30.5 m) on East 60th Street between Park Avenue and Madison Avenue. The geographically complex site is bounded by two fragile five-story masonry buildings on the east and west, a mid-rise building on the north, and a New York City Transit (NYCT) subway tunnel on the south. To add to this complexity, the ambitious development required an excavation between 70 and 80 ft (21.3 and 24.4 m) deep, mostly below groundwater level in highly-permeable rock, to accommodate four levels of cellars. The new building also cantilevers 24 ft (7.3 m) over a five-story historic building on the east. The limited footprint of the building coupled with large compressive and tensile axial loads, considerable base shear and over-turning moments, and the required deep excavation, presented unique foundation challenges. This article describes how the challenges were solved with an innovative combination of permanent secant pile walls and drilled shafts.Site GeologyThe 1865 Viele Map provides the site topographic conditions prior to development in the area, and indicates that the site was at the eastern edge of a historic marshland, which was approximately west of Park Avenue and north of 58th Street. A historic stream, which ran alongside the eastern edge of the site, was part of a larger stream network that traversed the surrounding area. This stream network is also visible in the 1865 Viele map. In addition, the bedrock beneath the site lies in a highly weathered zone due to a couple of ancient faulted zones that transect the site. These indicate that a zone of highly weathered rock is expected."

Jan 1, 2017

By Monica Prezzi

"Auger cast-in-place (ACIP} piles and drilled displacement piles are being increasingly used as foundation elements for structures, particularly in projects requiring accelerated construction or involving the rehabilitation of foundations of existing, overstressed structures. Auger cast-in-place piles (also referred to as continuous-flight-auger piles) are widely used to construct the foundations of all types of structures. There are many different types of drilled displacement piles, with the installation methods varying according to the equipment used. Depending on the specific rotary piling technology used, responses ranging from those associated with non-displacement to those associated with full-displacement piles are obtained. Conventional pile design methods do not account for how the various construction techniques involved in auger piling change the soil state around the pile during installation and, hence, cannot accurately estimate the pile resistance in a consistent way. Research on this subject, identifying the different variables that must be accounted for in design and linking these variables to installation methods, is lacking. This paper describes the different piling methods available for auger cast-in-place and drilled displacement piles, the equipment used to install them and the quality control processes typically used. It also reviews some of the design methods currently used.IntroductionDeep foundations are extensively used in geotechnical engineering practice. The wide spectrum of piling methods results in a variety of pile types. Each type behaves differently, depending on the installation or construction methods. On one end of the spectrum are non-displacement piles, the classicql examples of which are bored piles or drilled · shafts. These piles are constructed by removing a cylinder of soil from the ground and replacing it with concrete and reinforcement. On the other end are full-displacement piles, such as closed-ended pipe piles or precast reinforced concrete piles, which are typically driven into the ground. Driven piles preload the materials below the toe of the pile and displace the soil surrounding the pile shaft laterally during the installation process. Therefore, displacement piles are, in general, more likely to have a stiffer response than non-displacement piles. This is true particularly in the case of sandy soils where displacement causes densification."

Jan 1, 2005

By Bernardo J. Jiménez Vega, Edy L. T. Montalvan PhD

The experience gained during more than 900 Crosshole Sonic Logging (CSL) tests on drilled shafts shows the importance of establishing proper project acceptance and repair protocols. Drilled shaft evaluation is a multidisciplinary task that should not be left solely to the outcome of the CSL test. This test allows to characterize and delimit areas of different qualities of concrete, and it is important that all the interested parties understand the difference between flaws and defects. The information presented here is intended to give a guideline to contractors, inspectors, engineers, owners and clients on how to deal with acceptance and remediation of defective drilled shafts, detected using CSL tests. A database of flaws is presented depending on their location, intensity and remediation method. Procedures that allow the flaws to be analyzed are presented in order to dismiss or classify them as defects. In many cases, the CSL test may indicate an anomaly, but by coring the concrete and analyzing the structural demands and conditions, the flaw can be classified as non-severe. When flaws are classified as defects, their repair will depend on the area where they are located in the drilled shaft pile. In this document two procedures are described for repairing defects depending on their location. For defects in the drilled shaft head area, the procedure takes into account the interaction between the new and old concrete. For repairing the middle zone of the drilled shaft by grouting, the major concerns are the difficulty of accessing through the drilled shaft at deep depths and the communication between boreholes. For defects at the drilled shaft tip, two proposed remediation methods are presented. Finally, tomography tests are presented to compare the effectiveness of remediation by grouting.

Oct 1, 2022

By Babak Mamaqani

The Regional Connector Transit Corridor (RCC) is the Los Angeles Metro area's ambitious light rail project, running under the city's main thoroughfares, Flower and 2nd streets. When com- pleted, it will alleviate traffic and parking congestion downtown, while connecting thousands of residents living in the bedroom communities of Inland Empire and Long Beach to their jobs there. The rail line of 1.9 mi (3 km), which involves a $1.756 billion (€1.545 billion) budget to construct the under- ground rail line, including three new stations. They are the Grand Av Arts/Bunker Hill station at 2nd and Hope streets, Historic Broadway Station at 2nd Street and Broadway, and Little Tokyo/Arts District Station at 1st Street and Central Avenue, which will offer riders their first "one seat/one fare" ride option from Azuza to Long Beach. Regional Connector Constructors JV is led by Skanska USA Civil West California District Inc. (Skanska), in partnership with Traylor Bros., Inc. (Traylor), to deliver RCC to the Los Angeles County Metropolitan Trans- portation Authority (Metro). PB&A was the structural engineer of record (SEOR) responsible to design the shoring systems for the Grand Av Arts/Bunker Hill Station at 2nd and Hope streets, and Historic Broadway Station at 2nd Street and Broadway. The temporary shoring design for Historic Broadway Station is the focus of this article, and why the project received special recognition as a runner up for DFI's 2021 Outstanding Project Award. Two main challenges are discussed in particular: design of the shoring system considering all construction stages, and design of an underpinning system where the Los Angeles Times Building (Times Building) protruded into the station footprint.

Apr 1, 2022

By A. V. Rose

A redevelopment in the City of London has been constructed with a piled foundation system that is believed to be the first of its kind. The purpose of the research is to explore this novel foundation method, which involves the installation of closely spaced piles in a perimeter arrangement with a body of soil enclosed in the centre. Both centrifuge modelling and numerical modelling techniques are used.

Jan 1, 2011

By Arash Saeidi-Rashk-Olia, Dunja Peric

Energy piles are gaining increased popularity due to a growing demand for clean energy. To further advance the understanding of soil-structure interaction in energy piles, recently-derived analytical solutions have been implemented to investigate the impact of stratigraphy on the soil-structure interaction. This was accomplished by comparing the measured and predicted head displacements, axial strains and stresses in an energy pile embedded in the actual homogeneous and layered soil profiles, as well as into synthetic homogeneous soil profiles. The analytical solutions for homogeneous soil profile captured the smooth experimentally observed response versus depth very well. In the case of a layered soil profile, the corresponding analytical model was capable of capturing nuances in trends of axial stress and strain versus depth at the interface of different layers. The analytical predictions for the layered profile appear to be slightly less accurate than for the homogenous profile. The experimental data obtained from the layered profile appear to be a bit more scattered than those from the homogeneous profile. In the former case, the interplay of the individual soil layers with the pile occurs while maintaining the continuity of the pile stress and displacement at the interface of different layers. The response throughout each layer of the layered profile is quantitatively different than the corresponding homogeneous response. Nevertheless, qualitatively the response throughout each layer of the layered profile is similar to the response of the pile embedded in the corresponding homogeneous layer.

Sep 8, 2021

By Marcel Bielefeld, Joost Bakker, Rob van Dorp

Pile load testing can be performed by a static, rapid or high strain dynamic (generally designated as dynamic) testing method. The static load test is often considered the “gold standard” of testing with the other methods merely ‘alternatives’. However, the rapid load test, as a quasi-static test, has all the positive elements of the static alternative: the direct measurement of loads and displacements. Moreover as stress wave phenomena have no influence, the interpretation of rapid load test results is more straightforward than that of dynamic testing, and also independent of the person performing the interpretation. This paper will explore the Rapid Load Testing method and illustrate the advantages and limitations through a case study in Rostock, Germany

May 1, 2022

By Madhu. P, Srinivas. K

Measurement of thermal properties like thermal conductivity, thermal resistivity, heat capacity and thermal diffusivity for materials, it plays a crucial role in a wide range of various civil and electrical engineering projects, and many field applications like building’s basement, power generation, underneath soil heating, wastes from nuclear as well as thermal plants, and buried cables. Thermal conductivity of soil depends upon various geotechnical parameters such as type of soil, moisture content, particle size distribution, density, and compaction characteristics. Earlier studies, the measurement of thermal conductivity of soil by incorporating the heat source methods. Thereby expensive and time taken to conduct in laboratory as well as field measurements. The thermal conductivity is determined by fabricated probe and used in this work. Fabricated probe was calibrated with glycerin. The thermal conductivity of the soil increases as the water content and density increase because these factors are majorly influencing and water has a higher thermal conductivity than soil minerals, and grain to grain contact increases as density increases. therefore, Thermal conductivity is higher in coarser soils than in finer soils. The details regarding of this work as explained in this paper.

Sep 1, 2022

By Shawna Munn, Sarah Speir

Cedarvale Station is one of 25 new Eglinton Crosstown light rail transit (ECLRT) stations along Eglinton Avenue in Toronto. It is an interchange station with the existing Toronto Transit Com- mission (TTC) University subway line and is located at the intersection of two major thoroughfares. The new LRT tunnels run below the existing Yonge Spadina subway line and required total excavation depths of 20 m (65 ft) to facili- tate construction of the new station.

Jan 1, 2023

By Nicolas Moscoso, Gerald Verbeek, Marcel Bielefeld, Rob van Dorp

Upon recently, most offshore foundations were based on a number of driven piles that were installed with an impact hammer. With the increase in offshore windfarms two major developments have occurred: the shift from jackets to monopiles, leading to increase of the diameter of the foundation piles, and a shift from impact hammers to vibro hammers. As the use of vibratory hammers is becoming more and more common practice, the need for accurate vibro-driving simulation software has increased, which requires that the soil modelling is enhanced to address soil fatigue during pile driving and to predict reliably the soil behavior and resistance during pile driving. In addition pile driving monitoring, which is routine for piles driven with an impact hammer, needs to become common practice. This paper addresses advances in soil modelling that allows more accurate pile driving simulation as well as the application of Vibro Driving Analysis (VDA) or Monitoring (VDM) to validate the simulation results. This is illustrated by a case study of the test pile for the Delft Offshore Turbine project, a 28 m long monopile with a diameter of 4 m that was driven 15 m into dense sand layers using a vibro hammer. After some 6 months the pile was extracted, and pile driving simulations and VDA were done both for the installation and extraction phase. 1. INTRODUCTION At the end of 2017, the total worldwide offshore wind power capacity was 18.8 GW [1]. The vast majority of offshore wind farms are currently in Northern Europe, which together account for over two thirds of the total offshore wind power installed worldwide, followed by East Asia, while developments in North America are still in very early stages.

Jan 1, 2019

By Daniel A. Thome, Robert C. Janke

"Installation of permanent soil nails through distressed mechanically stabilized earth retaining walls is a cost effective and aesthetically pleasing solution when using the appropriate equipment and drilling methods for installation. A forensic investigation was performed on an existing mechanically stabilized earth retaining wall to determine the possible causes for the excessive horizontal displacements and visual structural flaws found along a portion of the wall. Reports concluded that the visual shifting was due to a number of factors including improper drainage in the vicinity of the wall and unsuitable compaction of the backfill material. Conceptual designs were proposed to the owner and the installation of permanent soil nails through the existing precast panels was determined to be the most practical solution. A total of ninety-three permanent soil nails were installed to lengths of up to 40 feet (12 m) through sand backfill and silty day fill using a hydraulic rotary percussion drill attached to a tract mounted excavator.IntroductionThe Illinois State Toll Highway Authority awarded Contract RR-03-5144 in the summer of 2004. Construction work for the project consisted of the rehabilitation of two existing concrete culverts and approximately 100 linear feet (31 m) of mechanically stabilized earth (MSE) retaining wall. The retaining wall is located below the southbound lanes of the Tri-State Tollway near the intersection of Federal Highway 41 in Wadsworth, Illinois as shown in Figure 1.Reports were prepared by Applied Technologies in cooperation with Giles Engineering Associates to determine the condition of the MSE wall and recommended conceptual designs to extend the service life of the wall.Nicholson Construction Company (Nicholson) wasselected as the design-build geotechnical subcontractor to install the recommended permanent soil nails through the existing precast concrete panels of the MSE wall. Rehabilitation of the wall involved the installation of ninety-three permanent soil nails through the existing wall, along with soil nail verification tests and proof tests on production nails."

Jan 1, 2005

By Paul Hewitt, Aaron Rastall

The New South Wales South Coast rail corridor is key infrastructure for both freight and passenger transport. Geomorphological and geological evidence suggests that land instability has been widespread throughout sections of the rail corridor, long before the first documented record of landslide activity in 1879. Major landslides occurred along a 25-km length of the South Coast Railway connecting Sydney and Wollongong because of significant rainfall events of the late 1980s. Since this time, several sites have been identified as subject to instability and treated progressively under a risk priority and safety management system. Two such sites comprise a station footbridge and overhead wiring structure (OHWS), both founded on high embankments overlying colluvial materials resulting in the structures’ potential movement and associated stability concerns. This paper presents these two sites as case studies, and discusses the project geology, geotechnical models developed, interpretation of monitoring data, and successful remediation of the rail structures using sleeved bored piles. The sleeved pile system was used to isolate bored piles, which separated the bridge foundations and OHWS from the moving soil mass to ensure the piles can carry the rail structure loads, unaffected by downslope soil movements.

Nov 1, 2022

By Anup Kumar Mandal, Sanjoy Chowdhury, Biswajit Das

"Tailing pond of an iron ore mine necessitated raising the height of its embankment to create additional storage capacity. The tailing pond is located in eastern India and raising the height of embankment was going on during the month of January, 2014. Upstream method of construction was adopted since there was no space available at the downstream side. During the construction, about 200 m stretch of the north east embankment of height about 5.5 m failed forming a classical slip circle on the upstream side involving about half the top width of the embankment. To find out the root cause of the slope failure, detail geotechnical investigation work was carried out within the embankment as well as in the adjacent areas within the pond. About 7.5m thick very soft tailings were detected below the constructed embankment. Shear strength of the soft tailing was very low and was inadequate to sustain imposed embankment load. This resulted in the failure of the embankment. Analysis of the tailing deposit revealed that even after failure, settlement was continuing due to imposed embankment load. Under normal onedimensional consolidation, the tailing deposit would have taken about 5.7 years for 90% of primary consolidation. However, in order to mitigate the scarcity of storage space, mining plan required raising the height of the embankment within next six to eight months. Therefore, despite the fact that there was a failure, it was necessary to continue the construction on the underlying weak stratum. The system was redesigned with installation of prefabricated vertical drains (PVDs) to accelerate the consolidation process thereby gaining the in-situ strength. Strength was additionally enhanced by installing geogrids in multiple layers. It stabilized the existing embankment and also ensured construction of additional height over and above the existing embankment.INTRODUCTIONBeneficiation plant in the Iron mines enhances the mineral content by separation of contaminants and fines. The residue (waste material) is called tailings/tailings depending upon the grain sizes. These tailings in a slurry form are generally disposed in a pond called as tailing pond/tailing pond. Height of embankment of such ponds is increased either by upstream or by downstream or by centrally raising methods in different phases as quantum of deposition in the pond increases with time."

Jan 1, 2015

By Chang-Yu Ou, Shao-Chi Chien, Hsuan-Hsiang Chang

"A field test was performed to investigate the applicability of electroosmosis with the injection of saline solution of Taipei silty clay. The calcium chloride solution and sodium silicate solution were used as the saline solution for the injection in this test. The results of this study indicate that injection using calcium chloride solution and sodium silicate solution during the electroosmosis to increase drained water from cathode and electro-chemical reaction can greatly improve the effect of electroosmosis and shorten the time of treatment. The results of field vane tests showed that the undrained shear strength after treatment increased an average of approximately 120% for a treatment period of 24 days.INTRODUCTIONThe first field application of electroosmosis in soil was demonstrated by Casagrande in 1939. Since then, more complete field applications of electroosmosis such as Bjerrum (1967), Fetzer (1967), and Lo et al. (1991b) have been made.The results of field electroosmotic work for a period of 120 days were presented by Bjerrum et al. ( 1967). The mean undrained shear strength, Su, increased from 18 to about 40 kPa, with a uniform surface settlement of about 0.5 m. Lo et al. (1991b), with a more sophisticated installation and a relatively larger spacing, also had positive results. For a 3 m electrode spacing during the treatment of a period of 33 days, the mean Su increased from 18 to about 25 kPa. Although the effect of the electroosmosis could be applied in the field based on the above examples, the response remained slow. For actual field work, the application of electroosmosis will be limited due to short project schedules and request of the effect of improvement."

Jan 1, 2005

By Michael Perlow Jr

A modification of the original Davisson Offset Limit (DOL) is presented for drilled foundations using soil quake (QDOL) factors ranging from 2 to 6. A further modification of the Davisson Offset Limit has also been developed using helical pile soil quake values (HDOL) based upon helix diameter. In addition, the initial tangent slope (IS) of the pile load test displacement curve is used in lieu of the calculated elastic slope (ES) to eliminate many of the uncertainties associated with determining the drilled foundation pile elastic modulus. The QDOL and HDOL load test methods do not require any graphical interpolation and provide easy simple ultimate pile capacity interpretation methods where drilled foundation pile load tests are not carried to plunging failure. Drilled foundation and helical pile load test case studies are presented to demonstrate the use of the modified soil quake QDOL and HDOL Methods.

It is my great pleasure as mayor of the city of Amsterdam to welcome you today to Amsterdam, and to the 10th International Conference on Piling and Deep Foundations. The history of Amsterdam has been connected intimately with your professions of geo-engineering and geotechnology, since its very first days. It is good to be aware that you are part of a very old tradition. The knowledge that we need today to build and renew the city has been gathered over a century long process so that we fortunately can stand on the shoulders of the giants before us. During the centuries people living in this part of the Netherlands have always struggled against the water. The same waters that brought the opportunity for a seafaring country to discover the world and to build an empire in the 17th century were a threat to the low lying Netherlands.

Jan 1, 2006