Search Documents

By Pierre Gouvin

This paper describes the design, installation and monitoring of a state of the art real time geotechnical/structural instrumentation monitoring system to facilitate tunnel construction under Interstate route I-5 in Seattle, Washington, USA. The project involved removal of existing highway foundation substructures on both North and Southbound lanes as well as the underground reversible high occupancy vehicle lanes. The system utilized state of the art 3-D pulsed laser scanning, wireless sensor networks, automated robotic total stations, tilt beam sensors, narrow angle tiltmeters, and in-place inclinometers. Dedicated real time data loggers, with a web based graphical interface, provided 24/7 access to critical measurements. In addition to the instrumented sections of wall and roadway subsurface which monitored physical measurements at known points, the pulsed laser scanning allowed complete site monitoring coverage where physical sensors were not located. This data allowed post processing at any location enabling the contractor and designer to respond to unforeseen structural responses to construction. Use of the instrumentation system resulted in the early detection of wall movement, and provided feedback to the designers to facilitate construction process changes in order to minimize further movement.

Jan 1, 2010

By Juhyung Lee

Numerical analyses were performed to analyze the behavior of two different type of suction piles (mono type and group type) under various soil layer conditions (uniform silty clay layer, uniform silty sand layer, and two-layer deposit consisting of clay and sand layers) and lateral loading locations (top, middle, and bottom of the suction pile). According to the results, mono suction pile shows maximum resistance when load is applied on its middle, regardless of the soil layer conditions, while group suction piles varies significantly according to the allowance on head rotation. When head rotation is allowed, the behavior of group type piles become similar to the behavior of mono suction pile. Whereas, when rotation is prevented, resistance is maximized when load is applied on the top head. Moreover, group suction piles show higher efficiency regardless of the ground condition and geological stratum. For further advances, concrete block on the top of group suction piles are suggested as an effective alternative method to prevent partial rotation and maximize ground resistance for group suction piles.

By Peter A. Thompson, Richard E. Prust

"The Bangkok Mass Rapid Transit (MRT} Chaleom Ratchamongkhon Line project is the first underground subway to be completed in Thailand. It consists of 22 km (14 miles) of twin-bored tunnels and 18 cut and cover stations constructed within the deltaic deposits that underlie the city. This paper describes the ground conditions, site investigation, including the use of the self-boring pressuremeter and the associated design issues for the construction of deep foundations. The paper also describes a selection of the various deep foundation solutions that were adopted to address particular constraints of the project and the ground conditions, including slurry walls for the cut and cover stations and foundations used for the underpinning of existing structures.INTRODUCTIONThe MRT Chaloem Ratchamongkhon Line Mass Transit Underground Railway comprises approximately 22 km (14 miles) of tunnels and 18 stations. The route is shown in Figure 1.The project was divided into two design and build contracts. The northern section was awarded to the ION joint venture, composed of Italian-Thai Development PLC, Obayashi Corporation and Nishimatsu Construction Co Ltd. Arup were contracted by ION for the design of the northern section. The section comprises 11 km (7 miles) of twin-bored tunnels, nine cut and cover station tunnels constructed within perimeter slurry walls using top down construction methods, and two cut and cover tunnel structures.The majority of the route of the northern contract follows existing highway Rights of Way. This results in the tunnel alignment passing through the foundations of existing highway bridge structures for which a variety of deep foundation solutions were adopted to underpin these structures.An 8-story park and ride building in the Lat Phrao area was also constructed using deep foundations."

Jan 1, 2005

By Matthew C. Janes, Mark C. Spence

"A former coal gasification site next to Rock Bay in Victoria, BC, Canada required a barrier to permit dewatering and excavation of the bay and surrounding property. The adjacent property owners had stringent requirements at the boundaries of their properties. Isherwood Geostructural Engineers designed a temporary steel sheet pile (SSP) water retention structure and excavation shoring system along the perimeter of the site. The project involved challenging geotechnical conditions in soft clay soils and a multi-faceted construction staging plan involving the diversion of two large storm water outfalls that drained into the bay. Despite a well-conceived design and construction plan, unexpected site conditions and delays led to significant changes in design and construction approach. Employment of the Observational Method and on-the-fly geotechnical investigation were instrumental in maintaining project momentum and schedule. The paper presents the geotechnical and geostructural design details and construction events as they transpired, highlighting the key issues, discussions and lessons learned.INTRODUCTIONFor over 100 years, the Rock Bay Site, in Victoria, British Columbia, Canada, had a legacy of contamination left behind from previous industrial activities. The site was the former location of a coal gasification plant that was in operation from 1862 to 1952. The site was also an infilling location for a nearby tannery and sawmill. The remediation of the Rock Bay Site involved the excavation and replacement of approximately 300,000 tonnes of contaminated soils on Transport Canada’s property. The project commenced in 2004 and has occurred over several phases on multiple properties. In the third and final phase of the project, a temporary steel sheet pile (SSP) excavation shoring system and ocean barrier wall – required to seal off the bay – was employed to enable disposal and replacement of approximately 90,000 tonnes of contaminated soils from the shoreline and base of the bay."

Jan 1, 2016

By Leo Panian

Over the last decade, drilled and post-grouted micropile foundations have come to be increasingly relied upon for resisting seismic loads in building foundations on the West Coast. Micropiles have been successfully deployed in a range of soil conditions, in vertical as well as battered configurations, to support a variety of structural systems difficult soils. Their high load capacity in tension as well as in compression, their ability to be installed in confined spaces with minimal overhead clearance, and their ability to be directly tested in an installation have made them indispensable for seismic strengthening of existing structures. More recently, growing industry experience along with improvements in design guidelines have led to wider acceptance of micropiles among engineers and building officials. The increasing availability of the specialized materials, coupled with growing familiarity with drilling technologies among design-build contractors has made micropiles more cost-effective and competitive. For the first time, micropiles are finding applications in the construction of new buildings, where they are combined with shallow footings in hybrid foundations to efficiently resist seismic loads. These new applications rely on more intensive engineering analyses to evaluate the performance of micropile foundation systems and develop detailed requirements for design and construction. This paper describes the design approaches and the analytical methods for the seismic design of hybrid micropile foundations, and provides examples of recent construction projects that demonstrate the application.

Jan 1, 2010

By H. Mori

This paper describes a new borehole loading test using a self-boring instrument appropriate for dense sandy soils and stiff clayey soils. The results of loading tests for the bearing strata of deep foundations according to this method are also presented. This method has been applied to the study on the settlement behavior of heavy foundations resting on dense sand, stiff clay or soft rock in Japan.

Jan 1, 2010

By Cau T. Bui

Thanks to Doi-moi (renovation) policy, many great bridges were constructed in Vietnam to meet demands of her booming economy in the recent decade and deep foundation structures were the only alternatives for the foundations of these great bridges. The deep foundation structures were constructed by modern technologies and almost of all these deep foundation structures were designed by foreign companies and carried out by Vietnamese workers and engineers under supervision of foreign experts. Beside successes, there were several failure cases in which the collapse of temporary scaffolding system of Can-tho Cable ? Stayed Bridge due to settlement of its pile foundation killing 54 workers and seriously injuring 80 other workers was the most serious. This paper introduces construction techniques of the deep foundation structures applied to building of great bridges in Vietnam recently. It will especially focus on two failure cases: 1) collapse of temporary scaffolding system of Can-tho Cable ? Stayed Bridge due to settlement of its pile foundation and 2) failure of drilled shaft foundation of Thanh-tri bridge due to poor construction technique and management. These two failure cases were greatly concerned by both bridge specialists and the public. Reasons of and lessons from these two failure cases will be carefully discussed. From the two failure cases, this paper will draw some lessons that should be important issues to be seriously paid attention when designing and constructing deep foundations in Vietnam.

Jan 1, 2008

By Richard Hanke, Franz-Werner Gerressen

"The twin decked Alaskan Way Viaduct is a passage to Seattle’s downtown waterfront and of great economic importance to the city. In 2001, the Nisqually earthquake damaged the viaduct and led to the redevelopment of this corridor. The project includes two miles of 57.5 ft diameter bored tunnel beneath downtown Seattle and a stretch of new highway and overpass bridges at the southern tunnel entrance. State-of-the-Art special foundation equipment was mobilized for the project to perform a broad range of geotechnical construction. Applications included soil mixing and jet grouting for confinement cells around new bridge foundations, large diameter secant pile walls for the Tunnel Boring Machine launch portal along with an extensive jet grouting regime for ground improvements within the tunnel alignment. This paper will study the evolution and use of advanced special geotechnical construction equipment and describe its application at the Alaskan Way Viaduct Replacement Project.INTRODUCTIONThe evolution of geotechnical construction equipment continues through innovative applications and continued modification or enhancement of machinery. Similarly and in parallel, market expectations continually demand more in terms of construction speed and performance. Together, market demands and contractor innovation have led way to the development of specialty geotechnical construction equipment with capabilities previously not seen feasible or possible. Several examples of this scenario have recently developed during design and construction of the Alaskan Way Viaduct Replacement Project.The Alaskan Way Viaduct Replacement Project is a joint project between the Federal Highway Administration (FHWA), the Washington State Department of Transportation (WSDOT), and the City of Seattle. Three build alternatives were under consideration for replacing the Alaskan Way Viaduct: the Bored Tunnel Alternative, the Cut-and-Cover Tunnel Alternative, and the Elevated Structure Alternative. Ultimately, the bored tunnel option was selected as the best value approach. The project includes two miles of 57.5 ft diameter bored tunnel beneath downtown Seattle and a stretch of new highway and overpass bridges at the southern tunnel entrance. Several other associated improvements tie into this project that will ultimately lead to the complete demolition of the viaduct and redevelopment of Seattle’s waterfront."

Jan 1, 2015

By X. Y. Hou

The design practice of several circular underground projects with large diameter is summarized. By taking the advantages of load-bearing of circular structure, a rational annular tensile bar support system and a new design method are proposed. Calculation for a car park shows that remarkable results are brought in by this design technique.

Jan 1, 2010

By Fei-chiu Huang

A 17-acre landslide occurred in February 2001, on a slope below Via Bellota in the City of San Clemente, California. Three homes were destroyed and many others placed in jeopardy. The landslide, involving portions of five separate developments, continued to move significantly in the years following. Litigation ensued among the affected parties, and investigations continued through 2007. A mediated repair resolution was ultimately reached among the parties. The agreed upon repair consists of a multi-million dollar stabilization program that included grading, drainage, and structural systems. Part of the construction cost was offset by creating 4 new ocean view custom lots and 20 new mobile home lots. The landslide repair and slope stabilization design involved removal and replacement of portions of the landslide debris and construction of buttress and stabilization fills as well as installation of 74 shear pins in two rows. The shear pins were designed as 4-foot diameter by 50 feet in length and incorporated continuous W30x211 wide flange steel. The shear pins were designed to be installed 25 feet above the slide plane and 25 feet below the slide plane at each location. Construction of the 74 shear pins was initiated in 2008 and completed in 2009. Four-foot diameter holes were drilled by utilizing a truck-mounted, flight-auger-style drilling rig with a 4-foot diameter solid-flight auger. Prior to the installation of the shear pins, an engineering geologist downhole logged strategically selected holes to further evaluate the actual slide plane elevations. The wide flange steel shear pins were then lowered to the desired elevations and encased within 4,500 psi, Type V, 0.45 maximum water/cement ratio concrete. Inclinometers installed within four pin shafts and behind the pin rows indicated performance in accordance with the design. Slight to non-perceivable shear displacement was measured which mobilized the intended capacity at the monitored shear pins. No excessive slope movement was detected at any of the inclinometer locations during or after the construction period. Actual shear displacement of the steel wide flange elements was less than the movement anticipated before shear pin installation.

Jan 1, 2010

By Ben C. Gerwick

Large diameter steel tubular piles installed vertically or on a slight rake, offer many advantages as the foundations of major overwater bridge in regions of high seismicity. By proper selection of diameter and wall thickness, an optimum balance between stiffness and strength can be achieved. Under strong seismic motion, the piles will deflect and bend so as to reduce the acceleration forces transmitted to the superstructure, while still limiting drift. A major advantage of this concept is that the mass of the footing block is significantly reduced from that of the conventional pier. The design of the footing block requires great care in order to transfer the high shears and moments. Where the soils consist of significant depths of sediments, the kinematic interaction of soils, piles and structures must be considered. Moments will be a maximum just under the footing block. Filling the top portion of the pile with concrete will prevent local buckling and assure ductile behavior even under overload. Typically the piles will be long, with most or all of their support furnished by friction and will require the use of very large pile hammers to achieve the required capacities. Where the piles are founded on rock or in hardpan, sockets will be drilled and filled with reinforced concrete. For these piles, high moments can occur both at the head and just below the rock surface, so the concrete infill should extend the full length. This paper describes the use of tubular piles driven through the deep silty sands of the Jamuna River, Bangladesh, and also where socketed into the near-surface rock for the mail pylon pier of the new San Francisco-Oakland East Bay Bridge in California.

Jan 1, 2013

By Bryan Bet

Retaining wall systems of soldier pile ground anchors (SPGAs) have been used for many decades to stabilize landslide activity. Due to successful use of these walls to address slope instability on the California state highway system, their use has expanded to include larger, more complex landslide mitigations. The increase in size and scope of SPGA wall applications, combined with more stringent seismic design standards, have created new and unique challenges for design and construction. Constructability issues are revealing themselves in real time in Northern California, where the California Department of Transportation (Caltrans) recently completed two large SPGA wall projects on state highways: the Peregrine Slide Project in inland Mendocino County, and the Westport Slide Complex located along coastal Highway 1. Each presented unique construction challenges that needed to be overcome quickly to make the projects successful. This article highlights some construction difficulties encountered on these projects, in greater depth, than what I covered last summer at DFI's S3: Slopes, Slides and Stabiliza- tion conference in San Francisco. Also covered are what steps were taken to overcome these difficulties, and mitigation advice for future wall designs. Specifically, ground anchor installation interference, ground anchor elongation variance, and difficulties with large diameter ground anchor drilled holes will be discussed.

Jul 1, 2022

By Tae Hwan Lee, Jun-Shin Lee, Daejin Kwag, Sangchul Bang, Gerard T. Houlahan, Moo Sung Ryu

"Geotechnical engineers have been installing innovative, permanent underwater foundation systems utilizing suction buckets for the offshore industry since the early 1980s (Senpere and Auvergne, 1982). This foundation system has been successfully used on numerous and various types of offshore structures in a wide range of environments. Suction buckets have numerous advantages compared to conventional underwater foundation systems. The more notable advantages include easy installation, large loading capacity, low noise and retrievability. The application of reduced water pressure inside the bucket facilitates the installation of the suction buckets, where a suction pump attached at the top of the bucket can accomplish the entire driving operation. Because of this efficient operation, very large suction buckets can be driven into the seafloor, which eliminates the use of a large number of small piles.In Korea, one of the most economical and reliable renewable energy sources is wind power; however, onshore wind power generation has encountered many problems, such as the lack of favorable sites and public concerns about noise and environmental damage. Consequently, offshore wind power generation has attracted increasing attention due to its abundant potential, high efficiency of grid connection, and availability of easy expansion.In November 2011, the government of Korea announced a national offshore wind power development roadmap, which targeted its offshore wind power generation with the goal of becoming one of the top three nations in the world for offshore wind power generation. Korea Electric Power Corporation Research Institute (KEPRI) is the main research arm of the Korea Electric Power Corporation (KEPCO) and conducts research and development on electricity, power generation, renewable energy and other energy-related matters. KEPRI ultimately provides forefront knowledge and leadership to KEPCO with respect to energy and related areas for its near- and long-term needs. Financial support for the overall project, of which the suction bucket foundation system installed for the pilot phase wind turbine is described below, was provided from the New and Renewable Energy Program of the Korea Institute of Energy Technology Evaluation and Planning funded by the Korean Government Ministry of Trade, Industry and Energy."

Jan 1, 2017

By David Coleman

This paper presents a case history involving the installation of drilled in piles with rock sockets for the Bicycle and Pedestrian Path project located west of the Henry Hudson Parkway within the Riverside Park between 83rd Street and 91st Street at the Hudson River in New York, NY. The paper specifically addresses access and construction procedures for a marine installation when working in an urban and environmentally sensitive setting.

By Richard Guenther

As available space in urban centers becomes more scarce, builders and developers are increasingly turning to vacant, existing structures to meet cities' growing needs. The developers of City Ridge Roadside Development and North America Sekisui House (NASH) - - found a suitable site for their "urban village" at the former Fannie Mae headquarters complex on Wisconsin Ave. NW in Washington, D.C., which had been vacated in early 2018. The urban village will consist of eight new structures centered around the building that currently sits on the site. All told, the project will include 687 residential units, a 150-room hotel, over 150,000 sq ft (13,935 sq m) of retail space, and 62,000 sq ft (5,760 sq m) of office space. A below-grade parking structure will extend across most of the footprint. The Fannie Mae building, which was designed in the Colonial Revival style to mimic the Governor's Palace in Williamsburg, Virginia, was named a historical landmark following a request from the development team. The central portion of its existing masonry structure was built in 1956 on pile caps with small-diameter cast-in-place piles. Two wings, which were added in 1962, were built on belled caissons. There are three levels above grade and one below.

Feb 1, 2022

By Tony Suckling

"As we head toward the United Nations Climate Change Conference in Copenhagen in December, the environment and sustainability will become headline news for a while. Governments are expected to agree to a set of binding targets to reduce carbon emissions probably before 2020, and certainly before 2050. This will, in effect, initiate a low carbon economy in many parts of the world. Sustainability has mainly been rhetoric so far, the exceptions being projects for those looking to the long-term future and not for short-term financial gains.The probabilities and consequences of negative impacts on the environment and on society over the short term and in the long term can be assessed and mitigated, but mitigation often adds cost. Also, we cannot know what technologies will be available, say 1,000 years into the future, which is about 40 generations of our society. It is easier to have a connection with 100 years into the future, which is only about 4 generations. Individuals may have a different sense of sustainability, and place a different value on mitigation, its cost, its importance and its potential impacts.Sustainability means different things to different parties on a construction project. For example, a land developer is likely to have a different view on the design in terms of sustainability than that of the designer. The developer may also likely to be more interested in sustainabiliy if there are tangible economic benefits that might accrue. Achieving sustainability on any project, leads to conflict between competing interests or demands cooperation between the economic and technical sectors involved. The foundations for a building or bridge, by definition, need to interact with the ground whose behaviour cannot be dictated by man. The aims of sustainability are the same as for the building or bridge, both of which are constructed of manmade materials, but it is less clear how they should be achieved. An example is the driven pile that does not produce spoil waste, but is likely to be too noisy to be acceptable in an urban environment. This then begs the question, should the public accept the nuisance of short-term pile driving to achieve a more sustainable foundation? Additionally, the question has to be asked, can the deep foundations industry develop its techniques and products to help make them more acceptable and appropriate more often than is possible now?"

Jan 1, 2009

By Ruth McKeown, Gilson de F. N. Gitirana, Murray Fredlund, HaiHua Lu

The current design standards for the use of anchors in slopes is based on two-dimensional (2D) limit equilibrium analyses. Anchors are considered as discrete loads and the 2D anchor, factored based on the spacing distance, corresponds to extending anchors indefinitely in the third dimension. A three-dimensional (3D) analysis offers a more realistic representation of the problem, including the true discrete nature of the anchor point loads. This paper explores the typical differences between analyzing anchors in 2D and 3D, using four typical conceptual models. Slopes with constant cross sections were shown to be adequately represented by the traditional 2D approach. The maximum difference between 2D and 3D models was 21% and becomes negligible for lower anchor spacing values, as expected. A slope with an external load was analyzed to evaluate critical slip surfaces with lower aspect ratios. Slip surfaces with lower aspect ratios presented higher edge effects that contributed to the stability of the slope. The results indicate that optimum design requires the 3D evaluation of field conditions inducing low aspect ratios, such as concave and convex surfaces, weak layers, and external loads. INTRODUCTION Slopes may be stabilized using a variety of solutions, including anchors. When performing an analysis, geotechnical engineers often follow the traditional two-dimensional (2D), Limit Equilibrium Method (LEM). It is important to understand the consequences and limitations of the assumptions on which the 2D LEM is based. There are numerous studies on anchors that show the importance of considering the actual three-dimensional field conditions. Desai et al. (1986) proposed a three-dimensional procedure based on the Finite Element Method and considering elastoplastic behavior and interface elements, to account for stress and displacement distributions, the relative motion between the anchors and the soil mass, and nonlinear soil behavior. Several important stabilization mechanisms were explained. The role of grout injection was evaluated in terms of the produced normal stresses along the anchor-soil bounding surface. The approach was shown to reproduce adequately experimental tests on a sand, proving realistic stress distributions around the anchor. Nonlinear soil behavior influenced to a large extend relative interface motions. Michalowski (1989) applied an upper-bound limit analysis in 3D to slope stability analyses. Anchors were not specifically considered in this study, but the consideration of locally loaded conditions shed light on important modeling aspects. The manner how the slide mechanism becomes three- dimensional as the slope is locally loaded was demonstrated. This emphasizes the fact that anchors should produce field conditions that require 3D analysis approaches.

Jan 1, 2019

By Roberto Nova

The selection of the Osterberg Cell (O-Cell) technology as the standard testing method for deep foundations of the Railways Po Viaduct in Northern Italy offered a relevant number of field measures on large bored pile behaviour in alluvial soils. The assessment of pile response during such ?non standard? testing procedure was performed through the comparison with standard top load tests on companion piles as well as by numerical models of the tests including a simplified pile-soil interaction scheme. As shown in this paper, the O-Cell technology allowed a careful assessment of the non-linear pile behaviour even at quite small loading levels as those required by a posteriori proof tests on production piles. Simple numerical models proved to be very effective in the simulation and the interpretation of pile behaviour during such unconventional testing procedure.

Jan 1, 2008

By Frank Rausche

Although Quality Control (QC) during construction is preferable for deep foundations, there are many instances when it is necessary to resort to Quality Assurance (QA) methods if, for various reasons, QC is not possible. Non Destructive Testing (NDT) methods for deep foundations are indirect approaches, i.e. in complex situations they do not provide complete information and need to be augmented by additional testing and/or analyses. While the challenges are varied for the different deep foundation types and the different test methods they are the same in many different countries. Experience of the tester is often mentioned as being most important for a successful quality assurance. In addition, reliable testing equipment for the best possible measurements and complete construction documentation for a meaningful data interpretation are minimum requirements for a successful test outcome. Another problem is the widely varying cost of the QA tests. For that reason the specifying engineer or authority has to be aware of what can reasonably be expected so that technically feasible specifications can be written for optimal cost and minimal construction delays. This paper discusses the most common NDT methods with a view on how these methods are applied world wide. It summarizes features of specifications, recommendations for test procedures and advanced analysis methods which can help to overcome uncertainty in the quality assessment of the foundation. Finally, the authors propose a decision tree for various QA methods, deep foundation types and soil properties.

Jan 1, 2008

By Garland Likins

The Texas Department of Transportation, now considering using Augered Cast-In-Place (ACIP) Piles (also known as Continuous-Flight-Auger or CFA Piles) in their foundations, awarded a research project to Professor Mike O'Neill at the University of Houston (UH) to study the advantages and potential difficulties with ACIP/CFA piles. ACIP/CFA piles were installed on three sites for UH; they had extra instrumentation and additional measurements by UH staff during installation which are beyond the scope of this paper. Independent visual logging of the pile was done by an experienced inspection firm. The main advantages of ACIP/CFA piles are their speed of installation and their economy. Potential savings are substantial. Disadvantages include an unknown structural condition of the shaft. Inspection is critical, but many simultaneous observations make accurate inspection difficult. Because of resulting uncertainty, many engineers have avoided ACIP/CFA piles in the past.

Jan 1, 1998