Search Documents

By R. Al-Hent, M. Aissa, J. Asfahani

"This paper focuses on determining the favorable geological and hydrogeological conditions for forming uranium occurrences in the Froqlos-Jabal Abou Rabah region, Palmyrides, Syria. Eighty rock samples from this area were analyzed by spectrometric gamma-ray technique to determine the radioactive concentrations of eU and eTh, and of %K. Uranium concentrations in shallow and deep groundwaters were also determined. High uranium concentrations were registered owing to the presence of phosphatic outcrops in the study region. The uranium migration trends and its remobilization were analyzed through the analysis of the behavior of eU, eTh, and their ratio. A positive relationship between eU and eU/eTh, and a negative relationship between eTh and eU/eTh in geological formations of different ages supports the secondary remobilization of uranium. The role of groundwater movement in transportation and redeposition of uranium mineralization is discussed: deep waters are less oxidizing than near-surface waters, and do not appear to have significantly remobilized uranium. This indicates that the source of secondary uranium mineralization is surficial or near surficial, and is mainly related to the leaching of outcropping phosphatic layers.Integration of the results with established radioactive and geological sections reveals four radioactive anomalous zones: north Froqlos, Kherbet Hannora, northwestern flanks of Jabal Abou Rabah (Kherbet Al-Hajar), and the northwestern limit of the Ghuntor depression. The high uranium concentration in north Froqlos is because of its original presence in the phosphate beds and extensive fracturing, which allows groundwaters to penetrate and remobilize the uranium. High uranium concentrations in the other three locations are caused by the presence of evaporites and capillary action, which draws solutions upwards and causes redeposition as surface crusts (gypcrete)."

Jan 1, 2009

By Monique Pharand, Jeet Basi, Simon Hille

"High quality activated carbon is essential in the recovery of gold in Carbon-in-Leach (CIL), Carbon-in-Pulp (CIP), and Carbon-in-Column (CIC) circuits. Goldcorp’s Campbell complex at Red Lake Gold Mines (RLGM) experienced a period of low soluble gold (Au) recoveries during Q3 2013, during which time the processing plant saw higher than typical Au grades in the CIP tails solution stream. A technical review identified that the CIP circuit may be experiencing a carbon-fouling issue. To further understand the degree of fouling, and to troubleshoot the low recovery problem, samples of carbon were collected from the CIP, elution, acid wash, and regeneration circuits, and submitted for characterization test work. This paper summarizes the steps taken to remedy the carbon-fouling problem at RLGM resulting in increased overall Au recovery.Overview of Red Lake Gold MinesRed Lake Gold Mines is located approximately 450 kilometres northeast of Winnipeg, Manitoba, in Ontario’s western boundary region.All mining is carried out through underground operations, utilizing overhand cut and fill, underhand cut and fill, and long-hole mining methods. Ore types include: silica-replaced carbonate veins with free milling gold, siliceous replacement-type mineralization (rich with arsenopyrite) marginal to veins, broad disseminated sulphide mineralization along major shears, and some minor sulphidized chemical sediment-hosted ore. The operation is supported by two milling complexes: Red Lake, and Campbell.Process DescriptionThe Campbell processing plant's main unit operations consist of grinding, gravity concentrating, flotation, autoclaving, leaching, carbon-in-pulp (CIP), carbon elution and reactivation, electro-winning, bullion smelting/refining and cyanide destruction, and concentrate handling. A schematic of the plant flowsheet is shown in the figure below.BackgroundHigh quality activated carbon is essential in the recovery of gold at many CIP/CIL/CIC processing plants. At RLGM, gold-bearing ore is milled and cyanide is added to leach the gold from the solids into solution. The dissolved gold then comes into contact with activated carbon, and adsorbs onto its highly porous surfaces. Gold is then recovered by separating the activated carbon from the main slurry for further refining. As such, the characteristics and quality of the activated carbon have a significant and direct impact on overall gold recovery."

Jan 1, 2016

By Mehdi Razavi

Scope of the Study The possibility and risk associated with mining two stopes at the same time The influence of Creighton Fault on the stability and dilution The effect of irregular shape of stope walls on overall stope stability and ore dilution The support requirements for proposed mining plan

Oct 1, 2010

By F. Ford, J. Dong

"Laboratory and miniplant testwork was carried out to reject uranium from an Iron Oxide Copper Gold (IOCG) deposit that contains an average of 60-70 ppm uranium with high variability. The dominate copper bearing mineral is chalcopyrite with minor bornite and trace covellite. The main gangue minerals are iron-rich chlorite, quartz and magnetite. The main uranium-containing mineral is uraninite (UO2). Downstream processes require the maximum uranium level of no more than 80 ppm in final copper concentrate.Mineralogical examination reveals that uraninite particles are finely disseminated with grain size of less than a few microns in the deposit requiring fine regrind in order to liberate uraninite from chalcopyrite particles. A lab flowsheet was developed to include ultrafine regrind of the rougher concentrate to the particle size of 80% passing 11-13 µm with up to four stages of recleaning in flotation columns. Finer regrind to 80% passing 5-6 µm may continue to improve liberation but does not decrease uranium level in the final concentrate. In each of the successive recleaning stages by flotation column after fine regrind, uraninite is rejected into the column tailings, with the final copper gold concentrate containing less than 70 ppm uranium from a feed containing 83 ppm uranium. The conceptual flowsheet was further tested in an integrated, continuous miniplant showing average 94% copper recovery with average 74 ppm uranium. The uraninite particles that report to the final concentrate are either locked with chalcopyrite or entrained as liberated particles of less than 5 µm in size.IntroductionIron Oxide Copper Gold (IOCG) deposits are copper and gold ores hosted within a large body of iron oxide and are significant ore deposits for copper and gold (Williams, et al., 2005). These deposits can also contain economic levels of other metals such as uranium and rare earth elements. The known sizes of IOCG deposits range from 10 to 4,000 million tonnes with grade of 0.2-5% copper and 0.1-3 g/t gold. One of the greatest IOCG deposits is Olympic Dam in South Australia. It is the fourth largest copper deposit and the largest uranium deposit in the world. Gold and silver in the deposit also contribute significantly to the total revenue."

Jan 1, 2017

By Jan E. Nesset, Antonio DiFeo, James A. Finch, Jose Hernandez-Aguilar, Cesar O. Gomez

"The gas dispersion measurement sensors and methodology developed by the mineral processing group at McGill University have to-date been employed at a number of plants in Canada, Australia, the U.S., South Africa and South America. In some cases the measurements have been directly linked with metallurgical performance while in others the gas dispersion surveys on their own have proved very useful in understanding the behaviour of the flotation cells. In addition to reviewing the current state of the gas dispersion measurement technology, the paper will present a series of case studies from the various plants and will show how this technology brings a remarkable new level of understanding to flotation behaviour. The influence of the bubble size distribution on recovery and grade are emphasized in the paper.INTRODUCTIONBackgroundThe advent of new sensors to characterize gas dispersion parameters in flotation cells is a development that is long overdue. While the chemistry of flotation has been studied since the early 1900’s, it is only now that the significance of bubble size distribution, gas rate and gas holdup can be meaningfully measured in-plant with robust and precise sensors. Early researchers, like T.A. Rickard (1916) recognized the importance of understanding the role of air and bubbles in flotation when he wrote in 1916 “we know that the key to the flotation process is to be found not in the oil, the acid, or the apparatus, but in the bubbles. The man who understands the mystery of a soap bubble has mastered the chief mystery of flotation”. In his 1999 review paper on The Froth Flotation Century D.W. Fuerstenau laments the fact that due to their “inert nature”, bubbles have never received their due attention from researchers who tended to focus on the chemical, physical, surface and colloidal aspects, rather than the physics of the process. It is perhaps fitting that now, 100 years after the inception of industrial flotation practice at Broken Hill, Australia, researchers and industry have turned their attention toward the importance of truly understanding the role of bubbles in flotation."

Jan 1, 2005

By Michel Massé

Eleonore Project- Agenda ? Purpose and Technical Overview ? SmartEXEC Control Capabilities ? SmartEXEC System Archetecture ? SmartEXEC System Advantage Eleonore Project- Purpose and Technical Overview ? Control air quality while maintaining target production levels at minimum energy operating cost ? Improve safety, work place conditions and operation flexibility ? Reduce energy consumption and green house gases footprint

Aug 1, 2013

The purpose of this paper is to present the methods used in ground water control and the considerations that affected the development of these techniques. Production at Knob Lake is currently proceeding at depths which may be as much as 200 feet below the original standing water table. In order to produce a more saleable product and to improve operating and maintenance conditions, it is necessary to depress the water table below the mining level. Considerable success has been achieved by drilling deep wells in strategic locations and installing vertical tur-bine pumps at depths of up to 400 feet. This method is especially suitable for operation under severe winter conditions and has reduced the detrimental effects by a far greater extent than other methods of water control, Spring runoff is handled in open sumps, but all other water from four mines, with flows exceeding 16,000 g.p.m., is pumped all year 'round from about thirty-five wells. T HE Knob Lake operation of the. Iron Ore Company of Canada is located on the Quebec-Labrador border, 320 miles north of Sept Iles,

Jan 1, 1965

The purpose of this paper is to present the methods used in ground water control and the considerations that affected the development of these techniques. Production at Knob Lake is currently proceeding at depths which may be as much as 200 feet below the original standing water table. In order to produce a more saleable product and to improve operating and maintenance conditions, it is necessary to depress the water table below the mining level. Considerable success has been achieved by drilling deep wells in strategic locations and installing vertical tur-bine pumps at depths of up to 400 feet. This method is especially suitable for operation under severe winter conditions and has reduced the detrimental effects by a far greater extent than other methods of water control, Spring runoff is handled in open sumps, but all other water from four mines, with flows exceeding 16,000 g.p.m., is pumped all year 'round from about thirty-five wells. THE Knob Lake operation of the. Iron Ore Company of Canada is located on the Quebec-Labrador border, 320 miles north of Sept-lies, a seaport

Jan 1, 1965

By Tom Gabardi, Peter Clarke

"MillMapperTM is a new 3D laser scanning technology that has only recently been introduced into the North American mining industry. It enables mill operators to gain a much more complete understanding of the condition of their mill internals and to more accurately predict how liners will perform in the future. This paper describes the technology and techniques used to obtain data on internal mill conditions, how this data is processed into meaningful information which enables better prediction of liner life and gives examples of the reports provided by the software. Examples are given, using client sites data, on how this information is being used to reduce the costs and improve the revenue from SAG and ball mills.INTRODUCTION Scanalyse Pty Ltd developed the MillMapperTM technology in Australia over a number of years and has recently introduced it into North America with a significant take-up in Canada. The technology was commercially released in Australia in late 2006 and there has been significant technical development in the features provided since that time. MillMapperTM has been accepted as a useful technology in the Australasian region and more recently has been introduced to sites in Chile, Peru, Brazil, USA, Canada, Laos and South Africa. Over 100 different mills have been scanned and the technology has been thoroughly tested and validated. It has become an integral tool in condition monitoring and improvement programs for SAG and Ball mills across many sites and is now providing significant and measurable benefits to the mining industry. Some of these benefits will be described in this paper using actual examples."

Jan 1, 2012

By R. L. Dunsmore

Introduction If one had been called upon to describe petroleum oil refining seventy-five years ago, he could have acceded to the request quite satisfactorily in about fifteen minutes. Fifteen years ago, an hour and a half would have been sufficient to give a general idea of oil refining, and of the equipment used for this purpose. Today, so extensive has been the research into all phases of the refining and manufacturing of petroleum products, and so rapid the strides in improvement in technique and equipment, that I doubt if a week would suffice to give an adequate outline of ail the ramifications of present-day oil refining. I propose to only 'hit the high spots', dealing particularly with the equipment and methods employed at the Imperoyal refinery, which you are to visit. Crude oil, the refiner's raw material, contains essentially only two elements, hydrogen and carbon. These are not present in the free state but are combined in various proportions as 'hydrocarbons'. A given crude oil is not made up of just one hydrocarbon, but of myriads; some solid, others liquid, and still others gaseous at atmospheric temperature and pressure, ail dissolved one in the other. Moreover, the nature and the relative amounts of the several hydrocarbons vary very considerably in crude oils from different sources. That is, a 'crude' from Oklahoma will contain hydrocarbons not present in crude from Mexico, and is different again from the Venezuela crude. Not only this but oil in a certain well in, say, Peru may be differently constituted from that in a well half a mile distant from it.

Jan 1, 1931

By Anna M. Ferrero

Stability condition of underground excavations have to be assessed to guarantee safe operations within the quarrying working areas. This objective requires a reliable assessment of the rock mass natural state of stress and of the stress redistribution induced by the excavations. This goal is often complicated by difficult geological conditions induced by tectonic stresses, complex topographies and large and irregular excavation geometries. Consequently, the acting state of stress needs to be measured by specific in situ measurement devices. This work refers on an in situ measurements campaign carried out by CSIRO tests in an underground quarry located in the Carrara marble basin. The difficult path carried out for interpretation of the measurements is described in this paper. In particular, the numerical modeling performed using the Boundary Element Method (BEM) first, to study the influence of both surface topography and excavation geometry and then the Distinct Element Method (DEM) to evaluate the influence of rock discontinuities in the measurement zone are illustrated in this work. Parametrical analysis of the rock mass mechanical features is also described in order to calibrate the numerical models and analyze the experimental results. The work has been carried out trough several phases, which are: characterization of the rock mass through geostructural surveys: this allowed us to classify the rock mass and determine the mechanical and physical parameters necessary for modeling; on-site measurement of stress levels through the application of over coring techniques; numerical analyses for the simulation of excavation phases, using the Examine3D (BEM) engineering analysis code. comparison between the measured stress levels and those numerically calculated and subsequent calibration of the BEM model; Numerical model of the forecasted excavation based on the calibrated (BEM) model.

May 1, 2009

By Charles Knilans, Tassos Grammatikopoulos, Nicole Hoffmann

"Twin Metals Minnesota LLC, (TMM) has recently completed a prefeasibility study evaluating the development and operation of an underground copper (Cu), nickel (Ni), platinum (Pt), palladium (Pd), and gold (Au) mining project on the Maturi deposit in northeastern Minnesota.The Maturi deposit is a magmatic Cu-Ni-sulphide deposit occurring along the basal contact of the South Kawishiwi intrusion, comprised of heterogeneous troctolites to gabbros forming a tabular body designated the BMZ (basal mineralized zone). These rocks provide the major gangue mineralogy (plagioclase, olivine, and clinopyroxene) with local, minor rock-forming orthopyroxene, biotite, magnetite, and ilmenite. Altered silicates exist within local fracture and/or alteration zones, which are commonly associated with minor faults in the regional area. The Maturi deposit is comprised of four main mineralized zones within the BMZ, referred to as Stage 1, Stage 2 (S2), Stage 3 (S3), and Upper Heterogeneous. Chalcopyrite, cubanite, pentlandite, and pyrrhotite are mainly hosted within the S2 and S3 units, with talnakhite frequently occurring within the S3 unit.A cross-discipline approach combining geology, geochemistry, metallurgy, QEMSCAN™ mineralogy, and mine planning has been implemented to develop a preliminary geometallurgical model and life of mine metallurgical performance forecast. This paper provides an overview of the methods that were used to develop the model and forecast, and discusses the advantages of such a model in project development and evaluation.INTRODUCTIONThe TMM Project proposes mining a copper-nickel-palladium-platinum-gold-silver (Cu-Ni-PGM) magmatic sulphide deposit situated in the Duluth Complex of northeastern Minnesota, USA. The prefeasibility study proposes a 45,000 million tonnes per day mine and concentrator facility to produce two saleable concentrates. The mine will access two separate deposits, Maturi and Maturi Southwest. Saleable concentrates are the final products of the sequential flotation plant where a high grade Cu concentrate is produced followed by a Ni concentrate."

Jan 1, 2015

By D. Eastick, S. Hardcastle

"Over the last few years, a multi-faceted feasibility study has been evaluating the introduction of hydrogen fuel cell-powered equipment into underground mines to replaced diesel engine-powered equipment. The analysis has shown that under normal operating conditions fuel cells could at the very least be an environmental and health benefit by eliminating combustion engines and their unwanted by-products. However, they could also generate significant reductions in the amount of ventilation a mine needs to supply when compared to dieselized operations; this would further decrease a mine’s energy consumption, its associated greenhouse gas impact, and also reduce a mine’s significant ventilation-associated costs. Fuel cell-powered equipment also has the advantage of lower noise and heat production compared to its equivalent diesel-powered counterpart.The degree to which fuel cells can generate ventilation benefits in underground mines depends upon a number of operational parameters and mine specific qualifiers such as current ventilation control or management, mine depth, inherent dust conditions, and minimum velocity requirements.However, another major consideration in the introduction of fuel cells in underground mines will be the safety requirements associated with diluting and removing the potentially explosive hydrogen in the event of a gas leak. In outside surface applications, it is possible to use dispersion, buoyancy, time, and lack of ignition sources as mitigating factors in deriving a low risk of an explosion. However, in underground operations, these factors change, and dispersion and buoyancy are limited; time may not be available and, in non-coal mines, ignition sources are not typically controlled. When a hydrogen leak occurs, the availability of sufficient ventilation to dilute and effectively remove the gas will be critical. Consequently, ventilation may be the prime risk controlling factor. In this paper, the authors evaluate the potential benefits of replacing diesel engines with fuel cells in powered production equipment, discuss the mitigating qualifiers that could limit ventilation savings, and evaluate solutions to retain and maintain an additional ventilation capacity in the event of an emergency situation, such as a hydrogen leak from the fuel cell stack or its distribution system."

Jan 1, 2007

By K. Bartholomew

The Functional Performance Equation for ball milling circuits provides plant staff with a new means to improve circuit performance. However, successful execution of a plant processing performance improvement project, with verifiable improvements, requires a significant number of accompanying steps beyond using this equation. In order to identify and articulate all these steps, a study was undertaken with the metallurgical staff from two milling operations and process application specialists from a grinding media manufacturing company. “Task analysis” of improving plant grinding performance was carried out. This analysis identified the required steps, and ultimately yielded a “Plant Grinding Circuit Processing Performance Management/ Improvement System.

Jan 1, 2015

By Goutam H. Shahani

Today, the mining and mineral sectors are being impacted by highly fluctuating supply ? demand, extreme price volatility and tremendous market uncertainty on a world-wide basis. This pattern is expected to continue for the foreseeable future. In particular, large consumers of tonnage quantities of industrial gases (oxygen, nitrogen) all have to make informed investment decisions in this uncertain economic environment. Plant owners ? operators need to carefully examine their current and future industrial gas needs in order to develop the most cost-effective industrial gas plant configuration. This can be done by partnering with an experienced engineering company that offers a complete technology portfolio for producing industrial gases. Ideally, the mineral and engineering companies have to work together as a single team to identify the most efficient and economic plant design. This includes an in-depth assessment of capital and operating costs, in order to deliver an optimal solution, taking plant reliability and process safety into account. It is important to consider all the industrial gas needs at a given manufacturing complex, in conjunction with available utilities and infrastructure to develop the best possible long term solution. Oxygen (O2) requirements include: oxygen enriched and oxy-fuel combustion, smelting and hydrometallurgical operations. Nitrogen (N2) is used for annealing. All of these industrial gas requirements have to be examined at a given site over a long term horizon in a holistic manner. Cryogenic air separation was first practiced at a commercial scale in 1902. Since then, the technology has been constantly refined to reduce cost; and improve reliability and flexibility. Today, using advanced engineering techniques, including proprietary process simulation, and modern fabrication techniques, it is possible to build air separation plants that are both low cost and high quality at the same time. It is important to work with an engineering company that owns a complete portfolio of industrial gas technologies, functional engineering capabilities and a variety of plant solutions. Such a partnership can quickly identify a ?sweet spot? for a given situation. By drawing on experience gained from hundreds of projects, it is possible to quickly optimize a given requirement. In situations where a customer wants a complete solution it may be appropriate to provide an air separation plant on a turn-key basis. This will enable the mining and mineral processor to focus on their core business. By using global procurement and construction capabilities it is possible reduce cost and improve project execution, thereby making industrial gas plant procurement simpler and cheaper for the mining and mineral sector.

Nov 1, 2011

By W. Greg Maybee

Separations, which form along stratigraphic boundaries in the roofs of potash mines, pose a serious safety concern. If these separations go undetected they can lead to falls of ground. The current method of identifying the location and extent of these separations is through manual scaling (sounding) using an aluminium rod. The potash mining companies would like to have a tool, which could quickly and reliably detect these separations and distinguish between them and clay seams. This paper presents the results of field trials undertaken at various potash mines in Saskatchewan belonging to the member companies of the Saskatchewan Potash Producers Association. A ground penetrating radar instrument from RST called SUSI (stepped frequency, ultra-wideband, synthetic aperture radar instrument) was used. SUSI has the ability of working over various frequency bandwidths. Four mines were chosen for these field trials, covering the different geological characteristics encountered in the Saskatchewan potash mines: Potash Corporation of Saskatchewan?s (PCS) Allan and Lanigan Divisions, Agrium?s Vanscoy Potash Operations and IMC Potash?s K2 Mine. These field trials indicated that stepped frequency ground penetrating radar technology could be ?tuned? to identify both separations and clay stratigraphy in the softrock, potash mine environment, based on the different spectral responses of the features.

May 1, 2004

By J. A. Finch

"A method of sampling and presenting bubbles for imaging for use in full-size flotation cells is described. The device (bubble viewer) comprises a tube attached to a sealed glass viewing chamber. The assembly is first filled with frother-containing water (to prevent coalescence) and the tube immersed at the desired location below the froth. For a few minutes bubbles are collected in the viewer free from slurry and are readily imaged. To reduce bubble overlap and the problem of defining the plane of view, the viewing chamber has a sloped side. Bubbles rise, encounter this slope, spread into a single plane and slide up. This simple expedient virtually eliminates overlap and provides an unambiguous focus plane - the underside of the sloped glass. The bubble image is captured and processed to give size data. The bubble viewer has been employed at several concentrators on different types of flotation cells. Examples of the images are given. The impact of position in the cell and the effect of changing gas rate on bubble size are illustrated. This technique provides a sensitive measure of the effects of process variables on bubble size.INTRODUCTIONDespite the extensive use of flotation in the mineral processing industry, the methodology employed for cell design is largely based on empirical rules rather than on first principles. One of the main reasons for this state of affairs is that the local flow structures encountered in industrial-scale machines are very complex. These flow structures are difficult to simulate under the controlled conditions of the laboratory and the difficulty to solve the mathematical models that treat the randomness of such flows also mean theoretical treatment is limited. Understanding flotation cell hydrodynamics requires reliable data, which involves the implementation of measurement techniques capable of performing both at the laboratory- and the industrial-scale, In addition, it is desirable that such techniques are amenable to automation to reduce extensive manual intervention in the data collection process."

Jan 1, 2002

By Rory Cameron, Chuck Edwards

"Stringent environmental performance criteria and regulations, and the desire to minimize water use have made membrane-based treatment and separation processes an attractive option. This has lead to many advances in all aspects of the technology. Membrane separation processes have found application in sea water desalination, brackish water treatment, decontamination of ground water, and wastewater treatment. Development of membranes with better resistance to harsh feed conditions has created new opportunities for the broader application of membrane separation technologies to mineral processing streams. There are examples in mineral processing operations, including treatment of acidic drainage, pre-concentration of pregnant leaching solution in heap leaching operations, separation of acids and metals from waste streams and intermediate process streams, as well as gold and cyanide recovery from a heap leaching operation. This paper provides a brief overview of membrane technology principles, followed by a discussion of current membrane technology applications relevant to the mining and mineral processing industry. The paper further explores the potential for the application of membrane separation as an integrated component in mineral processing operations.INTRODUCTION Increased regulatory pressures, emphasis on water conservation, and scarcity of water in arid regions have resulted in substantial changes in industrial practices in recent years. As a result, many industries have become more open to adopting innovative technologies such as membrane separation. The mining industry, which is typically very conservative, has adopted membrane separation as an effective end-of-pipe solution for effluent and acidic drainage (AD) treatment; however, its use as an integrated component in plant operations has progressed more slowly. With increasingly stringent environmental regulations coupled with the desire for low- and zero-discharge operations, the use of membrane separation technology for achieving acceptable environmental performance may be unavoidable in the future. The relatively small footprint requirement, versatility, and modular construction of membrane separation units facilitate their introduction into existing processes with a suitable feed stream. Membrane separation is not a stand-alone process that provides the ultimate solution to water and wastewater treatment; however, it can often be economically added to conventional waste treatment plants to increase throughput and/or decrease contaminant output (Mortazavi, 2008). Although membrane separation technology has become an established separation technique that is widely used in drinking water production and other industries, it is still considered an emerging technology within the mining and mineral processing industry. This technology offers many potential benefits such as clean water recovery from wastewater, significant reduction of volume requiring conventional treatment, decreased usage of reagents, and acid recovery, all of which lead to increased treatment efficiencies and lower reagent consumption. This could translate to smaller and more efficient plants with lower capital and operating costs and lower environmental impacts. Plant expansion may be facilitated by incorporating a membrane separation unit operation in order to utilize existing treatment systems at higher throughputs."

Jan 1, 2012

By Maryam Sadeghi, Jonathan Roy, Claude Bazin

"The operation of mineral processing equipments is intimately related to the mineral composition of the ore. However unit performances are usually characterized in terms of metal contents or recoveries as this data is easier to obtain than the mineral contents. This paper describes a method that combines the operations of material balancing and estimation of the mineral contents of the ore. The estimated mineral contents can be used for process analysis and diagnosis of operating problems.IntroductionThe ore that is feeding a concentrator is made of minerals that condition the energy requirements for the ore comminution and the performances of the subsequent separation circuit. Indeed a change in the mineral composition of the ore may lead to lower grinding mill throughput as well as lower recovery or grade of the economical products. Despite this relationship is recognized the mineral composition of the ore is seldom measured or estimated to provide regular information for the diagnosis of operating problems. Some methods such as the QEM-SCAN (Whiten, 2008; Lamberg and Vianna, 2006) are available to measure the concentration of the minerals in ore samples but the method is time demanding and plant operators usually base their evaluation of the plant performances on chemical assays of metals or elements since this data is easier to obtain from ore samples.Usually samples of the streams of mineral processing plants are collected on a daily basis to be assayed for strategic elements. The obtained concentrations are balanced to produce coherent data with the material conservation constraint and then used to characterize the day to day operation of the plant in terms of recovery of valuable metals and grades of the marketable concentrates. The behavior of contaminant elements can also be monitored from this data allowing the operators to explain for instance a lower zinc concentrate grade by a more important contamination of iron. However such diagnosis is only partial as the contaminant element can be transported by different minerals. Indeed the iron contamination of a zinc sulfide concentrate may be caused by an inadequate depression of pyrite or due to another iron carrying mineral. A possible way to answer the question is to determine the concentrations of the various minerals in the ore and produced sealable concentrates. Since measuring the mineral contents of the ore could be a demanding task one should consider to estimate this data from the daily chemical assays of the sample collected on the main streams of the circuit. Some authors have already investigated the problem. Whiten(2008) described a method to estimate the mineral contents of an ore sample. Lamberg and Vianna(2006) proposed a method to do a sequential mineral reconstruction followed by a material balance. Few of these methods account for the mass conservation of the reconstructed mineral contents."

Jan 1, 2016

By Paul E. Lamoureux

Introduction The Author As the pail of smoke and wartime destruction gradually rises from the surface of the earth, from all countries, statesmen assemble to discuss and prepare pacts and treaties which are designed to, once more, bring people of all nations to understand each other and live in harmony. Scientists and engineers throughout the world are also undergoing a drastic reconversion in their ideas and objectives. No longer do they think only in terms of destruction and twist their brains to develop more devastating weapons or to surpass production records of war machinery. They have turned their eyes and ambitions to more pleasant tasks and are taking stock of wartime developments in materials, fabricating procedures, and equipment, many of which had been carefully shrouded with a veil of secrecy, and are applying their new knowledge to the fabrication or improvement of the tools of peace. The next few years will see the gradual elimination of scores of substitutes and makeshifts, expedients which the constantly changing law of supply and demand' under wartime stress necessitated. The universal search for satisfactory substitutes, however, has resulted in a general awakening of plant engineers to the possibilities of materials with which they were relatively inexperienced, with the result that, in many instances, what was considered a substitution at the outset turned out to be more satisfactory than the original material, and, in reality, can be considered a worthwhile development. Not only have materials been explored, but existing fabricating processes have been reviewed, and others, built around the properties and characteristics of new materials, created.

Jan 1, 1947