Search Documents

By S. P. Lowe

Introduction In the following pages a general description is presented of the concentrator and cyanide plant of the Hudson Bay Mining and Smelting Company, Limited, at Flin Flon, Manitoba, together with some account of the steps which have led to the adoption of the present practice. For an account of the preliminary test-work and pilot-mill operation, the reader is referred to a recent paper by R. E. Phelan on the History of Flin Flon Mine up to Construction (1). Additional notes may be found in a paper which the writer presented at the Annual Meeting of the Institute in 1930 (2). The first ore was crushed in the present plant on July 1st, 1930, and the first ball-mill was started one month later, on August 1st. Since that time, production has been continuous with the exception of one month lost during a strike in the summer of 1934. There have been no major changes in equipment or methods of treatment since the present plant was built, but many minor changes have contributed to the improvement in results obtained and to the increase in capacity to the large tonnage now being milled. The accompanying flow-sheets indicate the equipment used in the several plants, with the average life and repair cost. As originally built, the concentrator was to treat 3,000 tons per day, but the capacity has been increased to 4,400 tons. The methods adopted to make possible this increase in tonnage will be referred to below. It was the intention to produce two classes of ore: (1) a heavy sulphide, and (2) a disseminated ore. The mill was consequently divided into two sections, each adapted for most efficient treatment of one particular type of ore. However, it was soon found that it would be impossible to mine the two classes of ore separately, so it was decided to treat open-pit ore, which varies greatly in character, in the sulphide section, and underground ore, which is fairly constant, in the disseminated section. This segregation is still maintained.

Jan 1, 1935

By Finley A. Campbell

THE Quemont and Horne mines are located at Noranda in north-western Quebec. As shown in Figure 1, the Noranda area lies between the Cadillac-Bouzan fault zone on the south and the Porcupine-Destor fault zone to the north. Both of these major structural lineaments appear to be geometrically, and possibly genetically, related to the Grenville Front. The regional geology has been discussed by Wilson (12), Cooke et al. ( 2), and others. The geology in the Noranda vicinity, as compiled by Dugas and Gilbert ( 3), is shown in Figure 2. The Cadillac-Bouzan fault zone separates the dominantly Temiskaming-type sediments in the south from the Keewatin-type canic rocks to the north. These volcanics, which vary in composition from rhyolite to andesite, form a broad anticlinorium with a general eastward plunge. A succession of dioritic stocks, sills and dikes have been mapped in the area. The principal granitic rock masses include the Powell, Flavrian and Dufault stocks.

Jan 1, 1962

By A. Mazhary

"Although sensor-based ore sorting has gained significant attention recently, sorting gold deposits still face a high level of skepticism by gold mining companies. In order to shed some light on the matter, this article looks at two different gold deposits that were examined using X-ray Fluorescence, Electromagnetic and X-ray Transmission sensors. The heterogeneity of each sample is measured based on the assay results of each particle and is related to its sortability. Multivariate linear regression analysis was also performed on the XRF results to find potential proxy elements for detecting gold. The results from these deposits were varied and each sample showed different levels of sortability. While both X-ray sensors proved efficient for different deposits, the electromagnetic sensor failed to produce any promising results. Despite unsatisfactory result for one sample, this technology can have significant advantages in terms of lowering the operational costs and improving head grades and recoveries providing that the deposit is amenable to such separation methods. Therefore, it is important to mention that sensor-based ore sorting is ore and sensor dependent, and as a result, it cannot be applied and be beneficial to all deposits. Therefore, amenability tests are required in order to examine the potential for sensor-based ore sorting before one can reject the idea.INTRODUCTION Although sensor-based ore sorting has gained significant attention recently, sorting gold deposits still face a high level of skepticism by gold mining companies. Except for a few cases presented previously, no new case studies have been published. Previously, mines such as Kloof Gold Mine in South Africa used an optical sorter to sort their waste stockpile in 2003–2004 (Von Ketelhodt, 2009) and then again in 2009 (Von Ketelhodt, Falcon, & Falcon, 2011). More recently, Coeur Operations utilized an XRT sorter for their Kensington Mine in Alaska (Lasley, 2014) and also Anglo-American Platinum used an XRF sorter to pre-concentrate Platinum Group Metals through an algorithm that used chrome, copper and nickel as proxies (Rule, Fouchee, & Swart, 2015)."

Jan 1, 2017

By Desmond M. Levins

"Australia has almost twenty per cent of the Western World's low-cost uranium reserves, located mostly in the Alligator Rivers region of the Northern Territory. At present, only one uranium mill is operating in Australia, but a number of new mills are planned for the early 1980s.Details are given of Australian uranium mining and milling proposals and the measures taken to minimize their environmental impact. Major factors affecting environmental impact are discussed, including treatment of liquid wastes, water management, control of radon and other airborne releases, and disposal of tailings. IntroductionAustralia is entering a new phase in uranium mining and milling activity . In the first phase of operations, between 1954 and 1971, about 10,000 tonnes of yellowcake was produced at five locations. Most of the production came from the mines at Rum Jungle in the Northern Territory and Mary Kathleen in Queensland. In the 1960s, the demand for uranium slumped, and much of the yellowcake produced at Rum Jungle was stockpiled by the Australian Atomic Energy Commission. The early uranium processing operations in Australia were typical of overseas practice at that time. Environmental problems were generally given low priority and pollution control measures were unacceptable by today's standards. There was little or no recycling of process water, acid waste streams were not neutralized and tailings dams were poorly designed. At Rum Jungle, oxidation of sulphides in waste heaps, tailings dumps and ore stockpiles subsequently led to destruction of vegetation and heavy metal pollution in a nearby river.In the early 1970s, major uranium deposits were discovered in the Alligator Rivers region of the Northern Territory. Significant orebodies were also located in the Great Artesian Basin in South Australia, in calcrete formations in Western Australia and at several locations in Northern Queensland. According to latest available estimates. Australia has about 160/0 of the Western World's uranium recoverable below $US 80 per kg U. Mining these orebodies will require pollution control measures more stringent than practised previously in Australia."

Jan 1, 1980

By N. F. Faria, F. Monteiro, B. O. Taiwo, A. Palangio, D. Fonseca, J. Manuel

This paper explores the interpretation and application of Particle Size Distribution (PSD) curves in optimizing blast design and enhancing downstream operations. The study looks at important factors like D50, D80, fines content, and the uniformity index to show how PSD curves affect the efficiency of different mining processes. The first section of this paper discusses the impact of blast design parameters such as burden, spacing, and explosive energy on the resulting PSD, highlighting their significance for downstream operations like crushing, and material handling. The section concluded that proper alignment of PSD with downstream size classes, like primary crusher inlet sizes, among others, can result in substantial cost reductions and productivity gains. The second part presents a case study from dstgroup aggregate quarry in northern Portugal, utilizing fragmentation analysis to evaluate blast performance and promote continuous improvement. The section specifically examines the effect of stemming material size on blast fragmentation, comparing the impact of using aggregate with a D80 of 12.32 mm versus a D80 of 21.94 mm. The D80 value represents the particle size at which 80% of the stemming material is smaller, making it a critical parameter in evaluating the stemming's effectiveness in confining explosive energy. The drilling and blasting designs were meticulously planned using O-PitDev and O-PitSurface software to ensure accuracy in blast parameters and layout. To assess the fragmentation resulting from these different stemming material sizes, the study utilized WipFrag 4 software. The software allowed for precise measurement of particle size distribution after the blast, as well as a detailed comparison between the two stemming sizes. Results from the analysis indicate that using bigger-sized stemming material led to improved blast confinement, which in turn resulted in better fragmentation compared to the smaller-sized material. The reviewed blast videos demonstrate that the larger aggregate effectively contained the explosive energy within the borehole, thereby reducing premature venting and directing more energy towards breaking the surrounding rock mass. This led to finer fragmentation with D80 = 1240.1 mm, D50 = 685.9, and Dmax = 2580 mm, which is advantageous in downstream operations like crushing and milling. On the other hand, the smaller stemming material (D80 = 21.94 mm) did not confine the explosive energy as efficiently, resulting in coarser fragmentation (D80 = 1327.37 mm, D50 = 750.76, and Dmax = 2370 mm) and reduced overall blast efficiency. These findings highlight the significant influence of stemming material size on blast performance and fragmentation outcomes. 

May 4, 2025

By Frédéric Flament

The aim of this paper is to present the development of a data validation software as component of a commercial mass balance package. Data reconciliation through mass balance is basically an optimization problem constrained by the law of mass conservation. As any optimization problem solved with a modern and robust software application, erroneous information or starting point will always lead to a solution, whether it is realistic or not. Moreover, good information wrongly weighted by an incorrect error model will lead to the same bad ending. In an industrial context where competition requires accurate information, data reconciliation without validation can be disastrous and calls for data validation before and after reconciliation. The challenge in automated data validation resides in the development of general theoretical solutions. Until now, none has been presented and only partial solutions are available. The development presented in this paper incorporates some of these partial solutions. The integration of human knowledge into the application paved the way to a more general solution. The combination ?theoretical validation ? human expertise? proved to be flexible and reliable enough to be integrated in a commercial data validation package. Numerous examples though industrial applications are presented. These applications demonstrate the validation of raw measurements, user support in the development of error models and validation of reconciled measurements.

May 1, 2001

By M. R. Julien, A. Maqsoud, J. Martschuk, B. Bussière

Acid mine drainage (AMD) from mine wastes is one of the most challenging environmental problems currently facing the mining industry. When mining wastes have the potential to produce AMD, the effluents produced have to be managed to meet existing regulations on water quality. The LTA impoundment (property of Barrick Gold Corp.) located near Malartic, Quebec, contains sulphide tailings that have the potential to generate an acidic leachate. The closure option selected by Barrick was to construct a cover with capillary barrier effects (CCBE), in which the moisture- retaining layer is made of non-acid-generating tailings. Since its construction in 1996, the cover has been monitored to evaluate its performance. For that purpose, various parameters have been measured, including the volumetric water content and matric suction in the different layers of the cover. This paper presents some of the main results from the monitoring program that started eight years ago. The results show that the cover is able to maintain a high degree of saturation in its moisture- retaining layer, acting as an oxygen barrier. The actual performance of the CCBE on the flat surface of the 60 ha site is better than expected at the design stage. The only concern with the LTA cover is the effect of slopes that can reduce the performance of the CCBE during dry periods. However, these effects appear only for short periods of time, and are limited to very localized areas, so that they do not significantly affect the overall performance of the CCBE and its ability to limit the production of AMD.

Jan 1, 2006

By G. Bonnivard

"A complete laboratory process for the treatment of lateritic ores containing a high proportion of iron, as well as chrome and alumina, has been established. The ores treated originate from the tropical zones and result from superficial climatic alteration. According to recent estimates, the known reserves of such ores reach many billions of tons, thus representing huge potential reserves for the elements they contain.The process used is based on the alkaline roasting of pelletized ore in the presence of sodium carbonate. This treatment results in the separate recovery of pellets of upgraded iron ore, pure chrome oxide and hydrated alumina. The research described in the paper aims at determining the best experimental conditions for obtaining the highest extraction of the required oxide from this type of ore."

Jan 1, 1967

By C. H. Wright

Introduction The rapidly expanding and increasingly complex Canadian industrial structure, with the mining, metallurgical, and chemical industries as a large integral part, has, in recent years, brought greatly increased importance and value to our industrial minerals. In the modern economy of our mineral industry the importance which is due the non-metallics has been somewhat overshadowed by the great value of our large metal production and, in addition, by the glamour and fascination usually associated with the mining and treatment of gold ores. The term 'Industrial Mineral' is used in this paper in its usual sense and refers to non-metallics other than fuels. Coal and petroleum products, including natural gas, are considered as industrial minerals in those applications in which they are used for strictly chemical process purposes. Certain reduction metallurgical industries are so closely allied to chemical industries that for purposes been of this discussion no attempt has made to differentiate between them. Chemical industry in Canada today is a fairly large factor in our national economy, whereas in 1898, when the Canadian Mining Institute was born, it was very small indeed. Chemical concerns are largely dependent on industrial minerals for raw materials and process supplies and, as the country has developed industrially, so have the demands for non-metallics increased, not only by chemical industry but also by other large consumers, such as the construction and metallurgical industries. At the present time there is a greater than normal incentive prevailing for new discoveries, due to the serious lack of balance that exists in our import and export trade. This fact has resulted in intensive efforts to rectify the situation by locating new deposits and re-assessing those already known in an effort to enlarge and improve our home production of raw materials and also to extend their processing in Canada for our own needs and for export. The rapid advances in science and technology that have taken place since 1900 have also resulted in many cases of beneficiation and utilization of otherwise too low grade materials in order to satisfy current demands. The purpose of this paper is to indicate the history and the trends of the utilization of industrial minerals in established industry and to indicate the important part played by non-metallics in connection with the opening up of new industries. Some consideration has been given to the continual competition between natural and 'synthetic products and to the general tendency towards more rigid specifications.

Jan 1, 1948

By Harold S. King

TWO summers ago I had the privilege of visiting No. 18 colliery at Glace Bay. Underground, we travelled along the haulage-way behind a powerful electric locomotive. The motor in this locomotive began to smoke badly and a carbon tetrachloride type of extinguisher was used several times during the trip. At the time, I noted a strong odour of phosgene. On my return to Sydney, I spoke to Mr. Harold Gordon, Assistant to the General Manager of the Dominion Steel and Coal Corporation, and warned him of the danger of using this type of fire extinguisher in confined spaces, since it is a well known chemical fact that phosgene, a dangerously toxic gas, is formed by the decomposition of carbon tetrachloride. This danger does not seem to be widely recognized, so it seems advisable that a more general warning be published. Attention was first drawn to the danger by the death of two men in the United States Navy Department subsequent to breathing fumes from carbon tetrachloride used in a fire, and when an employee of the Bureau of Mines also was overcome while fighting a fire with carbon tetrachloride liquid. These accidents led to an investigation of the decomposition products of carbon tetrachloride by a group of workers in the Research Laboratory of the Pittsburgh Experimental Station, U.S. Bureau of Mines, the results of which were published in the October, 1920, number of the Journal of the .Franklin Institute (1). Their experiments were conducted by two methods. The first consisted in applying the liquids to actual fires and -to hot metal in a closed room of 1,000 feet capacity, where the gaseous products, mixed with air, could be retained and analyzed. The second method was to pass the vapour:s in air through heated tubes of iron or quartz, where the humidity of the air and the temperature could be controlled.

Jan 1, 1939

By C Carbonneau

In order to successfully produce columbium pyrochlore concentrates, St. Lawrence Columbium and Metals Corporation had to face two principal problems met in several new operations but possibly made more acute than usual owing to the newness of the project. 1.-The ore is particularly complex, as it is made up of an elaborate intermingling of carbonates and discontinuous ultra-alkaline rock bodies of various ages and types in which no less than seventy mineral have been re-ported. Obvious petrographic or structural controls are lacking. Ore boundaries have to be defined on the basis of assay results and the determination of several minerals which occur in trace amounts. 2.-The pyrochlore concentrates produced had to com-ply with a set of stringent specifications. This fact, combined with the low Cb205 content of the ore, necessitated the use of a beneficiation process that would have to operate at a concentration ratio greater than 100:1. A brief description of the mill circuit is given. Mill stability was obtained through extensive mineralogical study of the mill feed coupled with close geological and engineering control of the mining operations.

Jan 1, 1965

By A. Luckita, A. Samtani, R. Barus, J. R. Donald, J. Syarifuddin

In conventional Rotary Kiln-Electric Furnace (RK-EF) laterite nickel processing, management of dust continues to be problematic. A more efficient processing of dust represents an opportunity for energy efficiency, increased production, and productivity. PT International Nickel Indonesia (PTI), together with Vale Base Metals Technology Development (VBMTD), has successfully developed and implemented a novel flowsheet enhancement that capitalizes on these opportunities. In the novel flowsheet, the dust recycle stream is moved forward in the RK-EF laterite nickel smelting process. The dust is injected into the kiln's main burner, as opposed to being recycled to the dryers. A similar treatment of dust is commonly practiced in the cement industry; however, application to nickel smelters has not been fully developed to date. This paper describes this dust insufflation technology, the process through which it was developed for laterite nickel processing, and summarizes the lessons learned. A key conclusion is that successful new technology development requires a multi-disciplinary team involving members from research and development, study management, engineering consulting firms, project implementation management, process technology and operations.

Jan 1, 2011

By L. Rodd, C. Walker, T. Koehler

"The energy content of slag represents approximately 80% of the total energy inputs to a laterite nickel electric smelting furnace. Conventional slag handling methods produce only low grade heat and the entire thermal content of the slag is wasted. A heat recovery system proven on BOF slag in the mid 1980's can be adapted to a laterite nickel rotary kiln electric furnace (RKEF) plant. Slag is granulated using a high velocity air jet inside a waste heat boiler to produce slag granules. Granules are cooled during flight via radiation to water-cooled boiler walls and by convection to the granulation air. This system has the potential to recover 80% of the total slag energy in the form of hot air and steam.Integration of the recovered slag energy into the RKEF smelter can be achieved by a number of methods, including the use of preheated air at the ore dryers, kiln or existing power plant. Energy from the slag boiler may be used to reheat boiler feed water from the power plant or to produce superheated steam and generate electricity. The heat recovery system can provide up to 25 - 30% of the total electrical requirement of each RKEF line and a reduction in CO2 emissions of 234,000 tonnes per year.The total cost of slag heat recovery, including CAPEX and OPEX, is $2.5/GJ, which is competitive with using coal when CO2 credits are $18 per tonne. With Clean Development Mechanism (CDM) carbon credits currently selling at €13 ($20 USD) per tonne CO2, there is considerable opportunity for slag producers in regions including South America, Korea, Indonesia and Africa. Increasing fuel costs and more wide-spread legislation for GHG emissions will likely create conditions in which slag heat recovery could generate a favourable return on investment."

Jan 1, 2010

By J. E. Hawley

Abstract Spectrographic methods for the analysis of minor constituents such as platinum-group metals, gold, silver, and silica in palladium and platinum refinery sponge are described. These involve the conversion of the sponge metals to the black form by reduction with high purity aluminum filings in either acid or alkaline media. Standards of known composition are prepared in the same manner from either refinery or spectrographically standardized sponge metals. Samples of the black metals are mounted in pellet form and a multisource spark discharge used for excitation. The range of concentrations of impurities studied are those common to refinery samples. Excellent reproducibility of intensity ratios using major constituents as internal standards, is demonstrated and two methods have noted by which the accuracy of the procedures are shown to be of the order of 3 per cent, on the basis of synthetic preparations. Introduction During the past two years an investigation has been carried out in the Spectrographic Laboratory, Queen's University, to determine the suitability of modern spectrographic techniques for the precise analysis of the platinum-group metals palladium, platinum, rhodium, iridium, and ruthenium in the form of refinery sponge analyzing about 99 per cent of the major constituent.

Jan 1, 1951

By W. Jomaa, V. Songmene, O. Mechri, Laval Université, P. Bocher, J. Levesque

"A 2D finite element modelling (FEM), based on pure Lagrangian approach, is developed for studying the serrated chip formation during high speed machining (HSM) of 7075-T651 alloy. The solution was achieved using a commercial software package, ABAQUS/Explicit v6.13. The Johnson-Cooke (JC) constitutive equation is used to describe the work material behaviour. Moreover, the JC damage equation is implemented into the FEM to take into account for the shear localization during the serrated chip formation. Modified Coulomb friction model has been used to characterize the sliding/sticking effects on the tool-chip interface with the friction coefficient and shear flow stress determined by force calibration and machining data, respectively. The proposed FEM is validated using experimental data obtained in HSM of 7075-T651. The FEM was able to predict accurately serrated chip morphology. The intensity of chip segmentation was found to increase with cutting speed.INTRODUCTIONHigh speed machining (HSM) is one of the most used processes for manufacturing aircraft parts with aluminum alloys. For aluminum alloys, the use of HSM increases metal removal rate and reduces the formation of built up edges and burrs. However, it was found that serrated (also named segmented or sawtooth chip) and discontinuous chips can be produced during HSM of some high strength aluminum alloys, such as 7075-T6 alloy (Rao & Shin, 2001). Many parameters were found to affect the segmented/discontinuous chip formation during the machining of aluminum alloys.There are two cases in which the serrated chip can forms: the first is when machining hardened materials (Morehead, Huang, & Luo, 2007), and the second, when machining ductile materials with a cutting speed higher than a critical value (Barry & Byrne, 2002). Different theories and models were developed in order to explain the formation mechanism of such kind of chips. According to Astakhov (2006), the segmented chip formation is attributed to variations in stress and plastic deformation states, and resulting temperatures on the cutting zone. Liyao et al. (2013) stated that the segmented chip formation was mainly attributable to adiabatic shear instability/catastrophic strain localization. Others (Vyas & Shaw, 1999) suggest that the fracture/crack propagation mechanism is at the root of chip generation."

Jan 1, 2016

By Matthew D. Meyer

SMART, an association of surface mining companies formed in 1995 to develop a coordinated approach to technology development for the mining industry, has recognized the need for the establishment of a worldwide database that continuously collects mining equipment data and provides metrics related to productivity and cost. Under the auspices of SMART, Syncrude Canada, Suncor Energy and Albian Sands Energy (three oil sands mining operations located in northern Alberta) have established a pilot project for mine benchmarking. This presentation will include a review of the pilot progress including: ???Data gathering techniques: means of collection and storage, proposed practice for data control and normalization, access to data/reports and format for data. ???Reports/analyses for individuals, across groups, within the total industry pool and publicly. ???Security and confidentiality of information belonging to identified parties. ???Sharing of best practices among members. SMART has identified two key deliverables to ensure success of the project. First, data supplied from surface mines must be validated and normalized to common definitions and then analyzed to provide participating companies with regular reports that allow them to understand their position and resultant opportunities to achieve world-class performance. This model maintains granularity of the data for each operation that can then be recombined into standard comparisons or specific indices as required. The general categories of: operating delays, maintenance downtime, standby, and scheduled downtime, have been used to frame comparisons. Second, participating companies are looking to go behind the indices to identify and share best practices that distinguish particular operations. The spirit of cooperation between the companies involved in the pilot project is meant to be a model for future expansion of the benchmarking project.

Apr 1, 2005

By Robert B. Parsons

"Originally intended to be implemented in 1977, but actually introduced effective May 6, 1974, the earned depletion regulations have been substantially refined and modified since their appearance on the Canadian tax scene, so that this important legislation now consists of a highly complicated set of rules which even the most astute follower of tax law has considerable difficulty sorting out!This month, Tax Notes attempts to cut through this bewildering array oj regulations, in reviewing the main features of the earned depletion allowance applicable to mining operations. Despite the phase-out of earned depletion allowances for most oil and gas operations as part of the federal government's new National Energy Program, earned depletion provisions are still alive and well for the mining sector, although they might well be slowly strangling to death in their own entanglement of complexity!"

Jan 1, 1981

By R. S. Bigelow

Part 1.- Metal Mines Early experiments with mechanical loaders in metal mines were confined largely to machines of the shovelling type and generally air-operated. Although the first application of the scraper to metal mines dates back to 1910, it was not until about twelve years ago that it came to be used extensively. Generally, the scraper gives better results in metal mines than in coal mines, as degradation due to soft bottom and breakage are not factors, but it has a wide range of application and is successfully used in the mining of salt, potash, gypsum, zinc, copper, and a variety of ores, from soft material to hard chunky ore which settles compactly. Today, the scraper has replaced to a large extent the shovelling type of machine in metal mines. Scrapers have offered an inexpensive solution for the mucking problem and are now employed in most mining districts throughout the world. They are operated by labourers of all colours and degrees of skill. Each installation, however, requires individual study on the part of the mine mechanical department to determine the type of scraper, horsepower of hoist, and most economical speed of rope, as well as method of rope rigging. Unfortunately, the scraper has no power to select pay ore from waste and its suitability for use under circumstances which might require sorting of the ore can only be decided by a weighing of the economic factors involved

Jan 1, 1931

We describe a new method of characterising the effect of dissolved materials on the rate of coalescence of bubbles in aqueous media. Single bubbles were allowed to rise to meet the surface of an aqueous solution, and the time of persistence between arrival and bursting of bubble was measured as a function of solute concentration. A laser beam was placed just above the surface of the liquid, with a detector in the light path, so that any disturbance at the surface could be seen as a break in the beam. The arrival of a bubble at the surface could be detected from the behaviour of the trace on an oscilloscope, and when the bubble broke, another significant change in the signal could easily be seen. The time between disruptions was reported as the persistence time. The effect of a homologous series of n-alcohols (C1 to C8) on the persistence time was measured, in aqueous solution. It was found that with increasing concentration of a particular solute, the persistence time increased up to a point, and then declined. However the magnitude of the persistence time was found to increase with increasing numbers of carbon atoms in the molecule. Bubbles of 1, 2 and 3 mm diameter were used. Persistence time increased with increasing bubble diameter, the maximum values observed being of order 100 secs. For a given solute, the persistence (drainage) time increased with increasing bubble diameter. The concentration Cmax at which the maximum persistence time was observed, was found to be independent of the bubble size. It decreased uniformly as the carbon number increased, and was well correlated by the function y1/2 (dy /dc) -2 I dc)-2 . There was no apparent correlation with the surface excess at maximum persistence time.

Jan 1, 2006

By William E. Roscoe

"Valuation methods are well established for mineral properties with production or imminent production, and include discounted cash flow and comparable transactions. Valuation methods for non-producing mineral properties, however, are more subjective. Non-producing mineral properties include those at various stages of exploration, properties at the prefeasibility or feasibility stage, properties with currently uneconomic mineral resources, and past-producers. Different valuation methods may be appropriate for different types of mineral properties.Income approach methods such as discounted cash flow and option pricing are generally not applicable to properties at the exploration stage. The market approach is generally appropriate to all types of mineral properties, although it is difficult to find good comparables because of the unique nature of mineral properties and the small number of transactions. Cost approach methods, such as appraised value and geoscience factor, are commonly used for exploration stage properties.Canadian standards and guidelines for valuation of mineral properties are in the process of being finalized by a Special Committee of the Canadian Institute of Mining, Metallurgy and Petroleum (CIMVal Committee). The CIMVal Standards are intended to be consistent with National Instrument 43-101, which sets regulatory standards of disclosure for mineral projects, and with International Valuation Standards. The intent of the CIMVal Standards and Guidelines is that mineral property valuation be carried out by appropriately qualified individuals and that all relevant information be disclosed."

Jan 1, 2003