Search Documents

By D. M. Muir

Many plants produce iron(II)/(III) waste liquors which must be treated by neutralisation and precipitation to remove the iron. Iron can be precipitated as crystalline goethite or jarosite by controlled oxidation at low pH and as magnetite by controlled oxidation at high pH, but only at elevated temperatures (>70°C). This study focuses on the characterisation and settling properties of the iron oxides produced at ambient temperatures using various neutralising agents in order to improve the performance of thickeners. It was found that two-stage addition of caustic to FeC12 solutions produced a fast settling material characterised by Mossbauer spectroscopy and XRD as maghemite and magnetite. However, lime and magnesia additions resulted in more ferrihydrite formation and much lower settling rates because of the enhanced oxidation of Fe(II) by air. Settling rates decreased significantly as the proportion of Fe(III) to Fe(II) in the liquor increased. The mechanism of iron oxide precipitation is discussed together with some reasons for the different behaviour of the neutralising agents.

Jan 1, 2006

By F. J. MacPherson, A. C. Caron

"Cassiar Asbestos Corporation Limited is at present B,C.'s only asbestos mining company, and has been actively engaged in the management and operation of the Cassiar Mine since the early 1950's. The Cassiar operations are located between 3,500' and 6,600' elevation in a secluded mountainous area of northern B.C., approximately 100 miles by road southwest of Watson Lake in the Yukon Territory. Climatic conditions in this area range from mild warm in the summer, to extremely cold during the long winter period.The minesite itself is located over a mile above sea level at the top of McDame Mountain, where year round 24 hours per day miners extract the chrysotile ore from the surrounding waste by standard open pit techniques. The ore body dips into the mountain at about a 45° angle, and as the mining progresses, larger stripping ratios are required. Waste to ore ratio this year will be more than 10 to l whereas only a few years ago ratios of 3 or 4 to l were possible. After drilling, blasting, and loading by shovel onto trucks, the asbestos ore is transported to the Primary Crushing Plant for crushing prior to transport by aerial tramway more than three miles to the Concentrator and Mill in the valley below, where the fibre is extracted from the barren host rock serpentine and milled into numerous grades for shipment to asbestos users round the world. The major air usage is associated with the milling process, presently requiring over 500,000 CFM, with future requirements expected to exceed 840,000 CFM by the end of the decade."

Jan 1, 1976

By M. G. Lipsett

"The Mining Information Technology User Group considers information to be a strategic enabler to improved business performance in mining. This ad hoc group has been meeting since 2000 to share knowledge and leverage their efforts in effectively using IT in mining. In this paper, core issues to mining IT are reviewed, along with initiatives to engage industry professionals and decision-makers in the potential for improved use of information in their operations. Relevance of IT to Canadian MiningMining operations always drive to improve their performance, and so far they have succeeded by using different technologies. While economies of scale have come in fragmentation and material handling, and energy usage has improved through conservation and design of integrated mineral processing plants, these systems have the net result of tightening operational constraints, through reduced excess capacity. There are higher opportunity costs of lost production when integrated, large-scale systems are operating in a sub-optimal way.The problem is that it is profoundly difficult to run a mine in an optimal way. Optimization requires a defined objective function (e.g., profit), which is hard to pose, let alone solve, because so many inter-related aspects of an operation affect the bottom line. Even for a small, well-defined process state, it is difficult to measure all the pertinent information with sufficient accuracy to ensure that the system is performing well in real time.The art of mining remains making good decisions with uncertainty: in the orebody delineation; in the allocation of resources; in the efficiency of the operation; in the reliability of components and systems; and in responding to the downstream market. As well, individual decision-makers need to know how their decisions affect other processes and systems, so that improvements in one part of an operation do not result in such degraded performance in the rest of the plant that overall profitability goes down."

Jan 1, 2003

By Ludwig M. Strah

"Wear is a universal problem and is present in all cases wherein one weighted surface moves with or relative to another surface. A practical description of wear as applied to mineral processing plants is outlined.With the advent of higher material and maintenance costs, more attention is being focused on the field of wear resistant linings. The aforementioned is magnified today as the production facilities continue to be designed to handle larger daily capacities. These changes, higher costs and larger plant handling facilities have necessitated the introduction of different materials and designs to combat the never ending battle against wear.In order that wear be understood, it can be relegated to two specific types:1 - Mechanical Wear - due to movement of one loaded surface relative to another.2 - Chemical Wear - more easily defined as corrosionMechanical wearMechanical wear can be subdivided into two basic forms:A.,Material movementB.,Material impactMaterial movement Abrasion is the result of, as earlier stated, the straight move¬ment of one loaded material relative to another.Material impact Is the striking effect when a mass strikes another from various angles and at various speeds. Impact can be severe enough to permanently damage and distort the basic component installed to overcome impact."

Jan 1, 1983

By H. C. Wade

"Description and UseDischarge liners or pulp lifters as they are sometimes called are a trough type liner used at the discharge end of the mill where ground ore passes to the trunnion.There are basically two methods of discharging pulp. The First and most common is the overflow method. Here ground ore travels from the feed to the discharge end where it exits through the discharge trunnion in an overflowing manner, hence the name ""overflow"". (See Figure I) The second method of discharging pulp is the grate method. With this method you block-off the trunnion and hold the ore inside the mill for a longer period of time. This allows only the desired size of ore out of the mill. Ore passes through the grate liners, into the Vibrathane Discharge liner, and finally down to the trunnion. Greater control of the ore size results wit1 this method as compared to the overflow method and it also eliminates reclassifying and regrinding. (See Figure 2)Types in UsePresently the majority of discharge liners in use today are rubber. (Metal insert and rubber covered) In some extremely course applications steel and nihard are used."

Jan 1, 1980

"Far from being eclipsed by petroleum and natural gas, Canadian coal continues to command wide (and apparently growing) interest.Major R & D investigations are currently heavily oriented toward coal beneficiation (e.g., cleaning and utilization of fines) and toward a broad range of studies on metallurgical coals and cokes. However, active work is also being carried out in the areas of coal geology, mining, transportation and combustion; and, in some laboratories, increasing stress has been laid on developing a number of new, essentially non-fuel uses for coal and coal products.This review summarizes the work of Canadian coal research agencies during 1966 and indicates some of the more important advances made by them."

Jan 1, 1967

By Vicki Tschirhart, Bill Morris, McMaster University

A new method for mapping faults within basement rocks underlying the Thelon Formation and glacial overburden was developed and tested in the Aberdeen Sub-basin. This method utilizes newly acquired aeromagnetic data, the Blakely algorithm for defining magnetic source edges, a calculated dip-direction map, a digital elevation model (DEM) derived from the Canadian Digital Elevation Database, and the positions of identified, inferred and newly mapped faults that are within and adjacent to this sub-basin. Combining these data revealed three age groups of faults. One group is seen only on the DEM; these faults are young brittle structures that have no effect on the sub-Thelon basement unconformity, and are not visible on the dip direction map. A second group is evident on the dip direction map but not the DEM; these faults are old basement structures that did not propagate upward through the Thelon Formation. The third group is expressed on both the DEM and dip direction map; these faults are also old structures that propagated upward during and/or after deposition of the Thelon Formation. The latter group of faults may be of greatest interest for uranium exploration, with reactivation increasing their potential to serve as conduits to transport uranium-rich fluids and focus deposition at or near the unconformity surface. This methodology has promise for comprehensive mapping of basin faults and tracking the tectonic development of the whole Thelon Basin through time.

Jan 1, 2013

By A. H. Lang

"IntroductionMUCH PROSPECTING, exploration, and development work was done for uranium in Canada in 1952, chiefly in northern Saskatchewan and in the Great Bear Lake region of the northwest Territories. The outstanding feature of the year was the great amount of work done in preparing for production at the Ace mine of Eldorado Mining and Refining, Limited, in the Goldfields region . of Saskatchewan. Many private companies and prospectors were also active in this region. Most of the other parts of Canada where uranium has been found received less attention than during the last few years, partly because so much interest was taken in the Goldfields region.In presenting this short summary of the year's activities now, the writer is handicapped because the season is not yet over; some discoveries have probably not yet been announced, and there has not yet been time to digest the numerous reports that have been sent in by companies and prospectors. In any case it would be impossible to give details for most of the discoveries and properties, because that would require a long report, and because that information is classed as confidential until released by the discoverers and companies concerned. It is only possible, therefore, to give a few generalizations, a brief out-line of the activities in northern Saskatchewan, even briefer ,accounts of the work in other parts of the country, and a few details that property owners have informed the writer he may publish or that have already been published by the owners."

Jan 1, 1953

By J. Paraszczak

For mining companies facing strong international competition and unfavourable commodities’ prices, automation of underground operations has the potential to increase productivity and help cut costs. However, despite considerable technological progress in this field, there still remain many problems to overcome. Furthermore, successful implementation of automation depends also on numerous operational, organizational, and even human factors. In this context, this paper briefly reviews technological progress with regard to different underground operations. Following that, several issues related to implementation of automated equipment and systems are presented and discussed. Particular emphasis is put on the factors whose importance is often underestimated. Some recommendations in this respect are also given. It is stated that the success of an automation project is a function of many “winning conditions,” which may be created through very thorough planning and preparation. It is also underlined that despite achievements made, a vision of a man-less underground mine is not yet as much a matter of near future as it may seem.

Jan 1, 2004

By D. D. Tannant

An experimental and numerical study was conducted on the geomechanical behaviour of oil sands during penetration tests in which a steel wedge with an apex angle of either 20 degrees or 30 degrees was forced into compacted oil sands. The boundary conditions simulated in the laboratory tests are similar to shovel penetration into oil sands. The objective of the laboratory tests was to measure the force required to push a steel wedge into compacted oil sands. A wedge penetration test differs from conventional triaxial tests in that much more shear is generated. The laboratory data was needed to improve calibration of micro-mechanical input parameters for a two-dimensional discrete element model of oil sands constructed with Particle Flow Code (PFC). Initial model calibration was performed with triaxial test data and then a PFC model of the wedge penetration test was constructed. The measured force-displacement behaviour of the steel wedge was compared with PFC modelling results. It was found that different combinations of PFC particle and bond parameters could equally well replicate the laboratory triaxial compression data for bitumen-rich oil sands. When the wedge model was run, it was found that the resulting force required to penetrate the wedge into the oil sands was about four to six times higher than that measured. This clearly indicates that further research is required to improve the predictive capability of PFC models of oil sands.

Jan 1, 2002

By Fathi Habashi

"Hydrochloric acid (HCl), although more expensive than sulfuric, find uses as a leaching agent in reactions involving iron oxide. The reason for this substitution was the discovery that oxyhydrolysis of ferrous chloride by which HCl can be recycled economically. This avoided the pollution of the environment by ferrous sulfate. It was found further that the rate of leaching of sulfides is faster when HCl is used as compared with sulfuric apparently due to the formation of aqueous chlorine. In case of refractory gold ores, HCl leaching under pressure avoids the use of cyanide solution since gold chloride is produced which can be recovered by standard methods. Hydrochloric acid find also uses in the leaching of scheelite and apatite but its use in leaching clay and anorthosite is questionable.INTRODUCTION Sulfuric acid is the cheapest acid and is used as a leaching agent in many hydrometallurgical processes. However, hydrochloric acid (HCl), although more expensive since it is prepared by reaction of sulfuric with sodium chloride, has replaced sulfuric acid in many reactions involving iron oxide. It replaced sulfuric acid for the first time in 1960s in pickling of steel because of pollution problems (Habashi, 2000). Ferrous chloride produced in pickling can be economically decomposed to ferric oxide and HCl according to:2FeCl2 + 2H2O + 1/2O2 ? Fe2O3 + 4HCl (1)which also shows that the acid can be regenerated but ferrous sulfate cannot be economically decomposed to recover sulfuric acid for recycle. Since then, HCl has been used in many leaching processes. Hydrochloric acid is a corrosive acid and is usually handled in rubber-lined equipment. REGENERATION OF HYDROCHLORIC ACID Regeneration of HCl is conducted in fluidized bed or in spray roaster Fluidized bed oxyhydrolysis In a fluidized bed, ferrous chloride solution is introduced onto a bed of hot ferric oxide where heating is provided by the hot fluidizing combustion gases (Figure 1). The solution is fed on top of the bed of oxides. The liquid feed wets the outer layer of the hot oxide particles and is quickly evaporated to form a layer of new solid oxide on top of the existing oxide, thereby producing dense homogeneous particles."

Jan 1, 2017

By L H. Warren

The types of equipment available for generating a plasma have been reviewed. The efficiency and potential of the plasma generating equipment used in performing extractive metallurgical reactions have been determined. A general classification of the reactions that might be per-formed in a plasma has been proposed. Experimental work done on extractive metallurgical plasma reactions, heat transfer between the plasma and solids, and the quench of the products of plasma reaction has been summarized. From the preliminary results it appears that the high-intensity are or the transpiration-cooled anode plasma torch offer the most promising areas for further research. C ONSIDERABLE world-wide research effort is currently being devoted to the development of processing technologies which employ the new high-temperature generating devices that have appeared over the past few years. The plasma flames produced by these devices offer the potential for subjecting materials to any single gas or mixture of gases at temperatures up to 20,000°K. With these conditions available, many reactions in extractive metallurgy,

Jan 1, 1965

By Rob Boom, Yasuyuki Tozaki, Frank M. Wheeler

Selection of a suitable site for a metallurgical plant is crucial for the success of the business case. For a brownfield project, with the decision to locate the project on a site with existing production facilities and activities, the selection of the site has been made. For a greenfield project, important economic and logistical considerations include proximity to primary and secondary resources and/or to the market, infrastructure, and access to energy and water. National and regional aspects, including the social license to operate, can be decisive in final site selection. Key to recruiting and retaining a labour force are proximity to urban areas, along with weather and health conditions at the site. Risk factors include site geotechnical parameters and topography, contamination, as well as probability and types of potential natural disasters.

Jan 1, 2015

By W. G. Miller, J. D. Scott, D. C. Sego

ABSTRACT: As part of an overall study of properties and processes influencing consolidation of oil sands fine tailings resulting from different extraction processes, self-weight consolidation tests were per-formed. Fourteen 2 m and 1 m high standpipe tests were instrumented to monitor the rate and magnitude of consolidation of seven fine tailings materials. Tests provided valuable information about the variation of consolidation related to differences in fine tailings material properties that result from a change in bitu-men extraction process (caustic versus non-caustic). In addition, the effect of adding a coagulant to caustic fine tailings was measured. Test results are presented and discussed in terms of consolidation rate long-term volume decrease, compressibility, and downward drainage. Non-caustic fine tailings had fasterinitial consolidation, which is important in tailings ponds for reducing storage capacity and returning decant water at a faster rate to the extraction plant. Similar results were obtained for caustic fine tailings with a coagulant addition. However, long-term settlement of the different fine tailings appears to con-verge to a similar value over time because it is then governed by effective stress.

Jan 1, 2011

By Grant J. Goddard

"The Iron Ore Company of Canada (IOC) has been in operation for over 30 years. Today, and in the future, technology and its application will play an ever more critical role in the company’s business success.The Carol Mining and Concentrating (CMC) division of IOC is energetically applying technology today to enhance performance and results, and is aggressively exploring opportunities to apply technology to support improved business results in the future.A critical area of focus is the application of technology to maintenance management performance. CMC has taken a “back to basics” approach to the fundamentals of maintenance management in 1995 and 1996. In parallel, the mine is aggressively implementing its Vision 2000 maintenance integration plan. This plan is targeted at levering the energies applied to sound maintenance management fundamentals as the company moves to a fully condition based maintenance approach.This paper discusses some of the strategies, key technologies and objectives of theVision 2000 maintenance integration plan at the mining operations of IOC."

Jan 1, 1996

By D. T. White

"Metallurgical extraction processes often call for the heating of aqueous slurries. Indirect heat exchangers are generally not feasible for service with high yield stress slurries because of low heat transfer rates. It is more appropriate to heat the slurry by direct contact, typically with steam as the heating medium. Although having a long and successful history, direct-contact heat transfer to aqueous slurries has been used without the support of pilot plant research. This paper provides results of the needed research, the work being done at a scale large enough to enable direct scale up to commercial operations. A pilot plant heater was constructed and tested to develop an understanding of the slurry heating process and to ensure that commercial scale heaters were appropriately sized.INTRODUCTIONPressure Leaching OperationsPressure leaching operations are often used to oxidise sulphide gold ores, or for extraction of nickel and cobalt from laterite ores with sulphuric acid. Where there is sufficient sulphur available, the exothermic pressure oxidation reactions can be self sustaining at temperatures as high as 225 ºC, without having to preheat the feed slurry. At lower sulphur levels, slurry preheating is required. This is typically achieved by utilising the flash steam released from the slurry letdown stages and contacting this directly with cold incoming slurry ahead of the autoclave. The vessels where this slurry-steam contact is made are known as heaters or condensers, with the number of pre-heat stages varying, depending on how much heat is evolved in the oxidation reaction (Mason, 1990).In nickel laterite pressure acid leaching processes, which operate between 245 and 270 ºC, the only significant exothermic reactions are those associated with dilution of sulphuric acid in the leach. As a consequence, slurry preheating with flash steam is always used commercially. In practice the number of flash steam preheating stages required varies from 1 to 3, driven by a number of factors, including other uses for flash steam and the upper temperature limit at which preheated slurry can be pumped. A diagram of a typical pressure acid leach train is shown in Figure 1.For pressure acid leaching operations and at low sulphur levels in pressure oxidation, boiler generated direct steam addition to the autoclave is required to sustain the reaction temperature. For this reason it is imperative that the flash steam – slurry heat transfer is efficient and the slurry temperature approaches that of the flash steam closely."

Jan 1, 2012

The Beginning ! The status quo simply isn?t sustainable ! Our social license is at risk ! The bar keeps rising ? We must improve our performance, both operational and social ? We must improve stakeholder judgement of our industry by taking action collectively Implementing TSM " TSM Guiding Principles " Performance Indicators " Crisis communications " External Outreach " Tailings management " Energy management " Performance manuals, guides " Reporting " Communities of Interest Advisory Panel

May 1, 2004

By Erwin L. Zodrow

"IntroductionThrough an extensive coal sampling project in the Sydney coalfield of Nova Scotia during 1981 - 1984 involving a majority of the mineable coals (Zodrow, 1985, Fig. 1), a sizeable inventory on trace, minor and major metals was established. In this paper, results of studying the inventory are summarized, concentrating mainly on the relationship that exists between metal variations and thickness of coal channel samples (i.e. trends) and on explaining the trends in geochemical and sedimentological terms. As an over-all conclusion the Everglades peat of Florida is proposed as a modern-day analogue to Upper Carboniferous peat swamp development that took place in the Sydney Basin.Data InventoryFor this study 17 channel samples were cut , 8 cm to 14 cm channel width and 8 cm to 10 cm depth, from 10 successive coals which in stratigraphically descending order are as follows: Point Aconi (3), overrider Lloyd Cove (2), Lloyd Cove (2), Stubbart (2), Harbour (4), Backpit (I), Phalen (,I), Shoemaker (1) and McAulay (I), where bracketed values signify the number of channel samples cut from a seam (Zodrow, 1985, Fig. I). Each channel sample was subdivided by 15 em incremental length yielding a total sample size of 137 for analysis. By appropriate modern techniques these samples were analyzed to determine concentration levels for 32 chemical elements and ash content, the average results of which are presented in Table 1.Tests were also made for Pd, Pt, Ga, Nb, Cd, Cs, Sm and W but their concentration levels in many instances hovered on the lower detection limits that were used and on this accounts are excluded from discussion. Ashing, when necessary for the determination of concentration levels, was done for 12 hours at a temperature not exceeding 450°C. Concentration levels for the elements are reported in reference to whole-coal or whole-coal equivalents and discussed on this basis. In the course of the analyses, lower detection limits received careful attention."

Jan 1, 1986

By Penny C. Stewart

Narrow vein underground stope design engineers in Australia have expressed significant interest in the requirements and methodology for developing site-specific stability charts. This is largely due to a concern that existing stope stability charts inadequately take into account factors influencing narrow vein stope stability, such as the effect of backfill abutments and the effect of in stope pillars. This paper presents conclusions from a comprehensive statistical examination of case history requirements for a site specific stability chart and critiques literature arguments for site-specific charts. A new statistical analysis technique and a large comprehensive stability database enabled the authors to quantify case history requirements and any site-specific effects the model exhibits. The analyses indicated that a reliable stable-failure boundary requires at least 150 case histories, of which a minimum of 10 percent should be unstable stope surfaces. Marginal site-specific effects were observed for the operating conditions captured within the database. The authors conclude that the apparent site-specific effects noted in previous literature are attributable to operating conditions inadequately represented in the database. Such operating conditions could induce erroneous stability predictions at any site, and are therefore not truly site-specific. Following from these conclusions, a strategy for taking into account operating conditions particularly relevant to narrow vein mining has been proposed. In particular, the development of a chart that accounts for the effect of backfill abutments on stope stability. Backfill abutment effects are particularly relevant to mechanised narrow vein mining methods such as modified Avoca. Collaboration from at least five sites is required to obtain access to relevant data and underground drives for geotechnical mapping. Preliminary estimations indicate that approximately three months fieldwork is required to meet case history requirements. CMS data in conjunction with 3-dimensional design software will be used to calculate equivalent linear overbreak/slough (ELOS). In contrast to stable, failure, major failure and caving categorical variables, ELOS is an objective and continuous stability variable and is therefore, more conducive to mathematical modelling.

Oct 1, 2001

By A. E. Cameron

MR. N. T. AVARD : I would like to congratulate Dr. Cameron on his presentation of some pertinent facts about the Coal Resources of Nova Scotia. There is no question but what there is something very definitely wrong about the coal mining situation in this Province. These are times when we can with profit look facts in the face and attempt to solve some riddles. Perhaps now is the time when we can bring some of these coal mining facts into the open and look them over. Co-operatively, we might evolve some helpful solutions. However, I would like, first, to make some specific reference to the Joggins coal field, not as a mining expert, but rather as an executive who has evolved some ideas after some years of practical contact with this field. Dr. Cameron states that existing operations in this area will probably continue for a few years. As a matter of fact, under normal conditions, these mines are good for another twelve years. With the installation of more powerful equipment for hoisting, pumping, and ventilation, an additional five years could be counted on. With one exception, that pretty well clears up mining from the outcrop, hitherto the only method of approach in this field. The chief reason for this present limitation is prolific 'bootlegging' operations. It is too bad that these should have been permitted to ruin a valuable coal field. Moreover, I am cold by competent authorities that this need not have been so. At one time shortly before war broke out there were 74 bootleg operations within an area of one square mile around Joggins. However, despite the fact that these operations were illegal, I could not find any means of stopping then and I believe the same conditions existed in many other coal areas in the Province. For some reason, the eyes of the law were closed. The result is that many outcrop possibilities have been permanently ruined. The exception noted in the so-called Queen seam, which has definite possibilities for approach through the outcrop. This is probably the best coal in the district.

Jan 1, 1944