Search Documents

By V. Coffin, T. Cienski

"(Figure 1) Reagentized pulp enters into the column at about 1/4 of the distance from the top. Inside the column it meets with a downward flowing stream of water and with an upward flowing mass of air bubbles. Flotation takes place in this counter current system while at the same time fine gangue particles are washed off the froth before it reaches the overflow lip at the top of the column. The main operating features of the column flotation are as follows:a) No moving parts. Solids are kept in suspention not by an agitating action of a propeller but by settling down against the rising air bubbles.b) Wash water. Spray pipes are installed a few inches below the froth surface and deliver required volume of water. The purpose of this water is twofold:(i) it keeps in balance the flow of material through the column and(ii) it washes rising froth in the froth layer as well as removes unwanted fines attached to the bubbles at the lower flotation section. As a result the concentrate produced is of higher purity than in the conventional flotation. Column is characterized by very high up-grading. However, even temporary disruption of wash water supply results in a drastic drop of concentrate grate.c) Flow balance. (Figure 2) For the correct operation volume of the underflow (tail) is larger than that of the feed. The difference is made up by the wash water. This difference called bias is predetermined and ranges from some 4 to 15 USGPM depending on the size of the unit and process requirements."

Jan 1, 1981

By J. E. Williamson

Introduction 1. Factors on Which the Design of the Roaster Plant was Based The roasting operation at Lake Shore, it was realized from the outset, would be profitable only if costs and losses could be reduced to a low figure. It was absolutely imperative that the operation should be self roasting over the whole range of tonnages and sulphur grades which might obtain during the life of the mine. The roasting operation could not bear the cost in fuel and labour of even a partially fired roast. To meet this requirement, it was necessary to resort to additional insulation in the construction of the roaster and to provide a more flexible means of rabble cooling than the conventional water jacket (see p. 31). A second basic consideration was that of handling a wet, putty-like concentrate. The operating costs of a drier ruled out the possibility of drying the charge before feeding it to the roaster. Moreover, the dusting which would result from charging a dry product virtually all -40 micron (325 mesh) in size would seriously handicap the use of a dryer. Dust lubrication (p. 3S) due to the back-mixing action of the Edwards rabbles, and the use of a Sullivan slapper ( p. 27) on the concentrate filter, completely solved the problem of handling the roast feed. The third consideration was the reduction of dusting to a sufficiently low point that a Cottrell or other dust collecting system was unnecessary. The Edwards roaster when properly supervised, it is believed, can be operated to give the minimum possible dusting. At Lake Shore, the evidence has been that less than 1 per cent dusting occurs at any time and that the greater part of the dust produced is recovered either in the spray tower or in the dust chambers.

Jan 1, 1947

By M. Ounpuu

"Gold, because of low head grade and recovery, is usually of minor importance in the economics of base metal flotation mills. Because of the above little metallurgical attention is usually provided to gold in these mills. But collectively, the gold losses can be significant. For instance, Noranda presently has interest in 13 base metal flotation mills with a collective gold recovery of only 50%. Gold losses are in the order of 150.000 oz per year!The Noranda Technology Centre, in cooperation with Noranda's milling operations, has been investigating the potential of gravity concentration of gold from base metal flotation mills. This paper outlines the pilot and plant testing conducted at three operations with distinctly different ore types; porphyry copper, complex massive sulphide and polymetallic semi-massive sulphide. Testing has been with the Knelson Concentrator which has proven to successfully recover fine gold in a simple, trouble free circuit. Discussion of issues which have risen from the testwork is included. INTRODUCTIONGold, because of low head grade and recovery, is usually of minor importance in the economics of poly-metallic base metal ores. TABLE I presents gold heads and recovery for some of Noranda's base metal mills. It should be noted that the stated recoveries are to payable concentrates, but does not reflect the actual payable gold recovery which in cases is significantly lower. Noranda's average gold recovery into a gold payable concentrates is about 45%. This equates to a collective loss in the order of $57 MM per year of gold"

Jan 1, 1992

By F. Flynn, P. Downey, G. Ritson

"Bell Creek Mill which has been in continuous operation since 1987 has undergone numerous operational changes in the past three years. The addition of over 2. 5 million tons of resource at over 13 git from Hoyle Pond Mine precipitated an expansion program for the Bell Creek Mill. This paper discusses the major changes that have occurred over the past two years to increase throughput and efficiencies. In addition, the refractory ore treatment options are also discussed.IntroductionThe Bell Creek Mill is located in the Timmins Goldcamp approximately 8km NE of porcupine Ontario. (Fig I.)The mill was originally constructed by Camamax in 1987 to treat the Bell Creek ore at a design throughput of 350tpd. The flowsheet (Fig 2.) consisted of two stage crushing, grinding, thickening, leach and drum filtration with gold recovery by Merrill Crowe.As ore depleted at Bell Creek, the Mill was purchased by Falconbridge to process ore from their Hoyle Pond property. Kinross purchased the Hoyle Pond property and Bell Creek Mill from Falconbridge in 1992.The successful exploration program at Hoyle Pond has led to several expansions and process design changes, with further changes planned over the next twelve months.In 1994, the mine produced 61,865 oz. of gold at an average cost of 197US$ per oz. In 1995 production was 91, 611 oz. at a cost of 187US$ per oz. Projecting the nine months ended September 30, production for 1996 will be 155,000 oz. at a cost of 165US$ per oz.In early 1997, the CIP expansion will be complete, with a target of 175,000 oz. at a cost of 176US$ per oz for 1997. The mill throughput will have increased from 400tpd to 1500tpd between 1994 and 1997.The changes to Bell Creek since 1994 have been numerous with very little of the existing equipment still in operation. The total cost of the expansion to date is 15 million C$. This paper discusses the major projects carried out during in this time. The focus will be to highlight the justification of each project, the design and engineering, some of the initial start-up problems and solutions.Figure 3 shows a plan of the existing mill facility together with the various additions that were carried out."

Jan 1, 1997

By T. Salman

Most authorities agree that the dissolution of gold from an ore takes place according to the Elsner equation first stated in 1846. The main requirements for the dissolution reaction to proceed are:(1) that the gold be clean.(2) that the gold be exposed to the solution.(3) that the cyanide solution be active, i.e., not over loaded with impurities which could retard or inhibit the reaction.(4) that an adequate supply of oxygen be available (from air).When the above conditions are met, cyanidation becomes basically a mechanical operation.Minerals such as quartz, calcium carbonate are relatively inert to cyanide though they may give rise to mechanical troubles. Most ores present an assortment of chemical problems, depending upon the constituent present, which react to the solution to varying degrees. It should be borne in mind that minerals which are disturbing to the operation, though present in small amounts, usually exceed the weight of the gold by several hundred times. In addition, the application of flotation and other forms of concentration to gold ores, previous to cyanidation, concentrates not only the gold, but also the other heavy minerals and these complicate the chemistry of the process.

Jan 1, 1975

By Peter Moser, Thoma Oberndorfer

"Within the research project “Mine Development” (Fettweis and Moser, 1990) a PC-based mine database has been built up since 1991 and so far includes detailed technical and economic data of about 150 under-ground hardrock mines in industrialized countries worldwide. These data represent about 50% of the underground hardrock mines in west and central Europe, Scandinavia, United States, Canada and Australia (Fig. 1). The mining operations included in the database have been visited directly and analyzed with respect to their deposit conditions, their general design and layout and also their operational and economic performance.The main aim of the Mine Database is to make a contribution to an improved planning of new underground hardrock mines. An analysis of current mine planning practices shows, that both personnel and company experience is still a dominant factor in planning new underground hardrock operations. Through the information included in the Mine Database the experience of a single per-son or company is supplemented by the experience of a wider group of people. The Mine Database makes the huge amount of experience that is available worldwide in the field of under-ground mining accessible for new mining projects. From that a contribution to a more reliable mine planning procedure based on the performance of existing mining operations is expected.In addition to its use in planning new mining operations, the Mine Database can con-tribute to the exchange of technical data among different mining operations, especially on equipment performance, etc. Such an information service is offered by the Department of Mining Engineering & Mineral Economics in Leoben and is already being used by different mining companies. To respect proprietory information, company specific information is not released under any circumstances.The cost of building up the Mine Database, so far, is about US$500.000 — two thirds of which is labour, and one third, travel."

Jan 1, 1996

By L. Larson

Rock samples were taken, away from zones of mineralization , from seven sections of five rhyolitic zones as define d by Spence (l967) in the Noranda area. The purpose of the investigation was to test whether there were intrinsic differences between the zones which would differentiate between non-productive zones and productive zones. For the elements sought (major elements, Cu , Pb , Zn and S) , no clear chemical difference between the zones was found. Thus, identification of a favour able zone from the over -all composition of the zone does not appear promising. Within sampled sections, there is no clear gradual compositional change up through the sections. A capping of highly siliceous massive rhyolite is present in five of the sections sampled. A layer of relatively basic material occurs near the base of individual units. The third (mine zone) and later zones contain abundant pyroclastic material, where as the non-productive zones do not.

Jan 1, 1977

By D. R. Spink

An historical background is presented to provide a basis for the lack of normally expected developmental effort over the first 20-25 years of viable zirconium production operations. This is followed by a description of developing technology, which is the result of years of research and piloting effort directed to the development of a more economical method to produce high-grade metallic zirconium. It is predicted that many of the process improvements described will have a significant impact on future zirconium production methods and consequently on future prices and markets.

Jan 1, 1977

By E. R. Packer

"The mill of Anaconda Britannia Mines is located on the eastern shore of Howe Sound, approximately 32 miles north of Vancouver, British Columbia. The mill has a daily capacity of 3400 to 3500 tons and at the present is treating chalcopyrite-pyrite ore from which only the copper mineral is concentrated. For a clear conception of concentrate filtering and shipping practice at Britannia perhaps a bit of past history should be related.For many years the mill concentrated copper and zinc minerals and intermittently a pyrite concentrate was produced. It was general practice to ship copper concentrate by towed barge down Howe Sound, across Juan de Fuca Strait and thence down Puget Sound to Asarco's smelter at Tacoma, Washington. Zinc concentrate was loaded in hopper bottom rail gondolas spotted on rail barges and towed to rail heads in Vancouver, thence by rail to Anaconda Reduction Works in Great Falls, Montana. Most of the pyrite produced was shipped by ocean freighters to Japan and Taiwan with an occasional barge load of 2000 to 4000 tons to nearby customers in Vancouver and the state of Washington.In recent years, because of smelter shut-downs for one reason or another, mostly strikes, a considerable amount of copper concentrates has been shipped by ocean freight to Japan and in 1971 several lots were loaded in gondola cars and shipped by rail to the Anaconda smelter in Anaconda, Montana, because Asarco's smelter was forced by municipal and state anti-pollution laws to limit the amount of S02 emission from the smelter stacks. Zinc concentrate production was halted in the early part of 1Y70 because of zinc depletion in the ores and pyrite production was stopped in May, 1971, because of a lack of markets.Filter equipment in the Britannia mill consists of conventional disc vacuum filters and reciprocating vacuum pumps. The copper concentrate filter was installed in 1923 as a 6 x 8'6"" American disc type manufactured by United Filter Corporation, The zinc concentrate filter, now converted as a spare for copper concentrates, is also a 6 x 8'611 American disc manufactured by Traylor Engineering and Manufacturing Company and was installed the same year. Formerly, there were, in addition, two 4 x 6' disc filters for pyrite and two 6 x 6' disc filters to de-water bulk flotation concentrates ahead of the regrind mills. Installed vacuum pumps were two Ingersoll Rand 22"" x 811 and one 22"" x 9"". One of the smaller machines has since been scrapped.At the time of the writer's transfer to Britannia in 1965, the entire filter system was operating as a unit using two vacuum pumps and a common filtrate tank with a 2"" SRL filtrate pump for five operating filters. The regrind and pyrite filters were in continuous operation and the co11p('r concentrate filter alternated with the zinc concentrate filter because both copper and zinc concentrates were transp0rted to storage by the same conveyor belt."

Jan 1, 1972

By R Zavadil, S Kuyucak, F Fazeli

Proton exchange membrane (PEM) fuel cells generate electricity by reacting hydrogen and oxygen. A thin, bipolar electrode material provides a medium for electron exchange with the electrolyte, alternately serving as anode at the hydrogen-rich side and cathode at the oxygen-rich side. Stainless steels have sufficient corrosion resistance to qualify as bipolar plate materials. However, the protective chromite layer increases the contact resistance, the battery’s internal resistance; and thus, decreases the electrical efficiency of the fuel cell. A heat-treatment is proposed and investigated via simulation by ThermoCalc / Dictra and experimentally, to generate a sufficient quantity of conducting surface carbides that breach the protective layer. Once carbide growth is arrested, a subsequent heat-treatment is also needed at a higher temperature to restore the corrosion resistance by filling-in the Cr-depleted layer (sensitization) around the carbide particles.

Jan 1, 2014

By P. D. Waters

"Mineral deposits are where you find them; they have no allegiance to territorial boundaries. Over the past decade much of the new investment in mining has been outside of continental North America, let alone Canada. The larger Canadian Banks have pursued this offshore business through their multi-national organizations; this reflects both the increasingly international orientation of today's business environment, and to a degree, the competitive advantage of these offshore developments.The current oversupply situation in mineral markets and the increasing maturity of the Developed World Economy reduces the need for new mining projects relative to growth' in GNP. Those that are brought on stream in the future due to their competitive advantage, will continue to be pursued by lenders and equity investors alike. IntroductionProspects facing those who search for mineral wealth were described rather well more than 200 years ago by a Scottish professor of moral philosophy, who also happens to be the father of modern economics.In search for new mines, Adam Smith wrote in The Wealth of Nations, ""there seems to be no certain limits either to the possible success or to the possible disappointment of human industry"".How true that statement remains today, where we are seeing economic cyclical problems compounded by basic fundamental structural change within the mining industry.Despite the enormous advances in earth sciences during the past two centuries, the rewards of mineral exploration still remain uncertain. Even though a promising orebody is found, ultimate profitability may still depend on the vagaries of the marketplace, where large and unanticipated changes in supply, demand and prices can play havoc with the best of calculations.The Canadian mining industry has had its share of disappointment during the past few years, with savage competition, shrinking demand, declining prices, and disappearing profits. But it has also had some share of success, such as at Hernlo, which now seems certain to provide some of the lowest cost gold production in the world"

Jan 1, 1986

By R. S. Fukuhara, M. J. Allan

"Highmont, a wholly owned subsidiary of Teck Corporation, operates a 25,000 ton/day mine and concentrator located in the Highland Valley of British Columbia. Construction of the plant commenced in the spring of 1979, and production from one grinding line began in late December 1980. The second grinding line began production in March 1980.The ore body consists of two main zones, the east and west pits, containing 134 million tons of ore, averaging 0.26% Cu and 0.27% Mo. Mineralization consists mainly of chalcopyrite (2/3), bornite (1/3), and molybdenite.The concentrator design incorporates an A-B-C grinding circuit (auto mill ball mill - crusher), followed by bulk flotation, copper-moly separation and leaching for moly concentrates. The two grinding and bulk flotation circuits are parallel and independent. Concentrate storage is provided between bulk flotation and copper¬moly separation and also ahead of molybdenite leaching. The plant design has been previously described in some detail. (""THE HIGHMONT CONCENTRATOR"" by C. V. Sibbald, CIMM Bulletin, March 1981).This paper will outline some of the problems associated with the construction, startup and early operation phases of the concentrator. The objective is to help others avoid some of the potential pitfalls by outlining those areas where problems occurred, or where things went well. Criticism of design or equipment is not intended."

Jan 1, 1982

By Réal Tanguay, Mathieu Piché, Jacques Carignan, Charles Beaudry, André Bonenfant

"Le gisement Isle-Dieu est situé sur le flanc sud de l'anticlinal de Galinée. La stratigraphie locale comprend, de bas en haut, la rhyolite du Groupe du Lac Watson surmontée par le basalte du Groupe de Wabassee. Un horizon repère, siliceux et sulfure, d'origine sédimentaire, appelé ""Tuffite Clef', est présent au sommet du Groupe du Lac Watson et pend à 45° vers le sud.Le gisement Isle-Dieu est constitué par une lentille qui recoupe, en partie, la ""Tuffite Clef"". Elle est séparée en deux trorçons par un dyke de tonalite. Les données obtenues à partir des forages effectues à travers la rhyolite sous-jacente permettent de définir les zonations chimiques et pétrographiques de la cheminée d’altération.Ces transformation minéralogiques et chimiques sont caractérisées par un enrichissement en MgO, Fe2O3, MnO et un appauvrissement en CaO, SiO2 et Na2O. La zonation spatiale de ces altérations permet de mettre en évidence la géométrie et l'extension des conduits hydrothermaux. L'épaisseur maximale des sulfures massifs au sein de la lentille est en étroite relation avec l’importance des zones d'altération. Les patrons de variations chimiques dénotent une orientation préférentielle WNW des conduits hydrothermaux. Les parties les plus altérées et les plus déformées présentent localement de fortes variations positives en Zr, Nb, et terres-rares; ces concentrations sont vraisemblablement imputables a /' enrichissement résultant de la diminution du volume lors de l'altération.L'étude pétrographique montre que la porosité et la perméabilité du milieu ont joué un rôle important dans la circulation des fluides car les roches de la cheminée présentent des phénomènes de dévitrification, de bréchification et de microfracturation très prononces. La nature magnésienne de certaines chlorites et la perméabilité accrue du milieu semblent en accord avec le modelé propose par Roberts et Reardon, ( 1978 )"

Jan 1, 1990

By C. S. Maggs, L. Shwydiuk, H. W. Newcomen

The southwest wall of the Lornex Pit at the Highland Valley Copper mine has been experiencing slope displacements since 1978. Measures to manage the displacements on previous pushbacks have included stepping out, scheduling pushbacks to unload the crest of unstable areas, slope dewatering and mining with intensive slope monitoring. The final pushback on this wall is currently being mined and substantial modifications to the slope geometry could prove to be uneconomical. As a result, a campaign of surface water collection and diversion, horizontal drainhole drilling and deep well drilling is currently underway to maintain an acceptable degree of stability to the end of mine life. The various factors contributing to instability, including engineering geologic controls, rock mass strength, and surface and groundwater hydrology are presented. Movement trends, displacement magnitudes and stability analyses results are also discussed.

Jan 1, 2003

By J. E. Udd, S. Bharti

"ABSTRACTMonitoring of stability conditions in underground mines permits management to assess the response of the rock mass to mining strategies. Monitoring of movements, if sufficiently early, may also permit operators either to avert potential failures or to develop alternative approaches to extraction.The Falconbridge organization has been a leader both in the uses of rock mass stability monitoring techniques and in the development of instrumentation.In this paper, the authors review the Falconbridge approaches to monitoring, and present case history examples to illustrate the application of the various instruments used.RESUMELa surveillance des conditions de stabilité dans les mines souter-raines permet aux chefs d'enterprises d'évaluer les réactions de la masse rocheuse aux méthodes d'extraction minière. Si le contrôle des mouvements du terrain est effectué assez tot, l'exploitant pourra prendre les mesures qui s'imposent, soit pour éviter les détériorations possibles ou pour mettre au point de nouvelles méthodes d'extraction.Le groupe de la Falconbridge a ére le premier a utiliser des techniques de vérification des conditions de stabilité de la masse rocheuse et a mettre au point l'appareillage requis.Ce document présente une revue des méthodes employées par la Falconbridge pour assurer la surveillance active de la stabilité de la masse rocheuse et illustre au moyen de cas concrets la manière d'utiliser les divers appareils."

Jan 1, 1987

By M. W. Grabinsky, B. D. Thompson

ABSTRACT: Use of cemented paste backfill (CPB) offers economic and environmental advantages over other backfill methods. However, many operations have limited knowledge of how their CPB behaves in situ. Therefore, to avoid over-pressuring containment barricades, backfilling strategies necessarily tend to be conservative. In situ monitoring at Barrick Gold Corporation’s Williams Mine and Inmet Mining Corporation’s Cayeli Mine has been conducted and factors controlling barricade pressures are demonstrated, including rise rates, binder content, stope geometry, and tailings properties. The application of barricade pressure monitoring on a stope-by-stope basis can increase backfilling efficiency and, thus, reduce stope cycle times, while maintaining optimal safety.

Jan 1, 2011

By D. M. Wyslouzil

"This paper was prepared for presentation at the 16th Canadian Mineral Processor's Annual Meeting, Ottawa, Ontario, Jan. 17 to Jan. 19, 1984.This paper gives an account of the development of treatment procedures for the differential flotation of refractory copper-zinc ores. Special references are made to the effectiveness of various zinc depressants and their combinations.Studies carried out on refractory copper-zinc ores demonstrated that conventional zinc depressants such as cyanide and zinc sulphate were not particularly effective when secondary copper minerals were present in the ore; the flotation activity of sphalerite was enhanced in the presence of cyanide.Among the various zinc depressants evaluated, the following depressant combinations were found most effective: Zn(OH) 2-S02 , 802-CaO, Na2S-Na2S03-S02, Na 2 S-S02 and Na 2S-S0rDS22.The practical application of any of these systems depends on the type of ore treated and other conditions such as pH, levels and points of collector and depressant additions.In this paper the effect of each depressant combination on different ores is described with reference to the selection of collectors."

Jan 1, 1984

By Peter Raziszewski

"A ball charge dynamics model is presented. Simulation results are compared with observed data showing good correlation. Based on the charge dynamics models, a liner wear model is presented along with some wear simulation results. Using the charge dynamics model with the liner wear model, it is possible to envision the predictions of mill power consumption as a function of liner wear. Further work is needed to validate the liner wear model.IntroductionFrom a process control point of view, industrial systems can be considered stationary or non-stationary. For example, the physical properties, such as geometric and/or material, of a system considered stationary do not change with time. However, this is not true for non-stationary systems such as those found in the mining industry where process dynamics are often violent with wear being an intrinsic process phenomenon.In this paper, a model for ball charge dynamics will be presented along with a description for liner wear. Simulation results for power draft prediction using the charge model will be compared with observed data. Further, liner wear results will also be presented."

Jan 1, 1997

By B. W. Williams

The crack propagation behaviour of Zr-2.5Nb pressure tube material was studied through comparison of the measured behaviour with the predicted response from finite element analysis. Three-dimensional finite element simulations of compact tension specimens were performed using the crack tip opening angle as a fracture criterion to allow for crack propagation. To obtain reasonable agreement with the measured behaviour, it was important to capture both the anisotropic plastic deformation behaviour of the Zr-2.5Nb material through use of the Hill-48 yield criterion and damage due to void growth, nucleation, and coalescence through the use of a Gurson-based constitutive model in the simulations.

Jan 1, 2010

By D. Kidby, A. Briggs

"Vitrokele ™ is a synthetic adsorbent, using chelating groups on large polystyrene beads, developed in Canada over 7 years ago, and first commercialised in 1985 to recover noxious metals from plating wastes.Pilot plant trials have been performed in Australia and Canada to demonstrate the recovery of cyanide and removal of metal cyanide complexes from gold plant effluent using Vitrokele1 M 912. The pilot plants comprise a simple adsorption train (similar to a CIP circuit) followed by complete elution facilities, so that loaded Vitrokele™ can be stripped and returned to the adsorption circuit.An account of these campaigns is provided, showing the reduction of total CN levels from over 200 ppm to less than 0.5 ppm and Cu levels from approximately 100 ppm to less than 0.3 ppm in treated tailings.Comparisons between pilot plant results and laboratory test data are given and probable future work on the process and its application to the gold mining industry is discussed.INTRODUCTIONThrough millions of years of evolution, life forms have developed specialised molecules with exceptionally high affinity and selectivity for various metals such as iron, cobalt, zinc and copper.In the early 80's professors at the Faculty of Medicine of McGill University engaged in research on the extremely efficient ways that living cells captured trace metals essential for life.As research progressed, it became evident that the special molecules used by biological systems to capture metals could be synthesized to capture selected metals with similar efficiency from water or other solutions.The technology was first commercialised in 1985 to recover noxious metals from plating wastes with compositions applying the special molecules (chelating groups) on vitreous particles (hence Vitrokele™). To date approximately three commercial Vitrokele™ plants have been installed for treating plating waters in Ontario and Quebec."

Jan 1, 1992