Search Documents

By Henderson J

Iron ore samples selected from the Deepdale, Iron Prince and Mt. Newman ore bodies have been pelletised on a pilot scale plant and subsequently reduced under laboratory conditions by hydrogen or carbon monoxide. Pellets approximately 1 cm in diameter have been reduced by hydrogen over the temperature range 5000- 900¦C and the results examined by thermogravimetric, microscopic, electron probe and x-ray techniques. After an initial time delay it was found that up to 95% reduction the rate of reduction could be described by a transport con- trolled porous model, in which the effective diffusivities of hydrogen in theòpr¦duct layer and the reaction zone are filar. Independent measurements of effective diffusivity supported the values obtained from the reduction data. ve 95% reduction the rate decreased markedly due to the formation_of retained wustite or fayalite. Comparison with reduction by carbon monoxide over the temperature range 7500 - 900¦C showed that the rate eduction by carbon monoxide was approximately five times slower than the rate by hydrogen. The rate of reduction was found to be a function of the properties of the pellets, which may account for the ely conflicting results that have been obtained in previous investigation on porous pellets.

Jan 1, 1970

By R H. Eric

Surface wave formation induced by a high-strength submerged jet in a bottom blown metallurgical vessels has been studied experimentally by using one-seventh water model of CLU (Creusot-Loire Uddeholm) reactor with two different tuyere configurations. Experimental results have been discussed in terms of the wave period, wave frequency and wave amplitude with respect to air injection rate and tuyere configuration at a 0.23 m bath height. The results from high speed photography observations displayed the formation of rotating surface waves which circulates within the water model. It was found that the frequency and the amplitude increased with gas injection rate. The wave period for off-centre nozzle orientation was found to be lower than those of the centre configuration. The experimental results also showed that the frequency of a rotating wave increases when the tuyere orientation becomes off-centred . The predicted amplitudes were in very good agreement with the experimental values over a range of gas flowrates between 0.00599m 3/s to 0.01081 m 3/s.

Jan 1, 2000

This paper outlines the aims, objectives and means by which a life of mine land use plan was established for Comalco's bauxite mine at Weipa. Comalco realises the need to strategically plan for future mining activities and still minimise the impact of operations on the natural resources of the region. With this realisation long-term forward planning has been implemented to improve the Company's ability to select future sites for mining, industrial use, agriculture, town expansion and conservation purposes.The knowledge of mineral, water, soil and animal resources has expanded dramatically in the past decade. During 1990 Cornalco purchased Geographic Information System technology which has allowed previously collected resource data to be presented in map form. These maps as part of the Life of Mine Land Use Plan are both information based and strategic which can be efficiently updated. The maps allow a broad audience from engineers, geologists, environmental scientists and site managers to government officers and the general public to comprehensively view and scrutinise the operations.

Jan 1, 1992

By Fabjanczyk MW, Guy RJ, Tarrant GC

The design of the reinforcement systems required to stabilise mine roadways has developed through the application of field measurement techniques. These techniques have allowed the level of security of a given opening to be determined from an assessment of the loading within the reinforcement, the extent of roof deformation and experience. The design systems developed are now used extensively in a wide variety of geological environment. Recent interpretative techniques have been developed to improve the level of confidence when designing roadway reinforcement. The techniques are particularly applicable for roadways subject to either weak materials or extreme stress levels. A second area of application is where roadway advance rates and hence the timing of reinforcement placement are critical. The newly developed techniques include both analytical and computational models. The validated computational techniques allow a more rational approach to investigation of the effect of varying reinforcement type, timing of placement and density on the level of stability achieved.

Jan 1, 1992

By Chappell BW

A zone of northwest trending dykes extends for over 600 km in the hinterland from Cairns to Mackay. In sate regions the zone is up to 120 km wide. Figure 1 shows their approximate extent, compiled from published regional maps and from specific studies in more limited areas : Palm Islands, Cardwell Ranges, Jourama Falls, Townsville area and Burdekin Delta. The context of the dyke swarm is the Tasman Orogenic Zone, the region of Eastern Australia conprised of Palaeozoic metamorphic, sedimentary, volcanic and plutonic rocks which has experienced a complex history and evolution. In the Whitsunday region, the Tam-an Zone also involves Cretaceous volcanism and plutonism. Geological relationships indicated a wide span of ages for the intrusions in the dyke, swarm zone. They intrude a range of volcanic and sedimentary rocks, and in some areas plutonic rocks. Older dykes, apparently part of the same regional swarm are intruded by sate of the granites.

Jan 1, 1987

This paper addresses the area of utilising automatic data capture systems in the metalliferous mining environment for the purpose of tracking personnel and vehicles, for both safety and productivity purposes.As automatic data capture systems in the form of barcodes have revolutionised the stock control procedures in retail establishments in recent years, so too will similar systems in the form of radio frequency identification products (an electronic version of the barcode) transform the way in which many aspects of mining operations will be managed.

Jan 1, 1992

The Queensland Magnesia Project is based on a unique cryptocrystalline nodular magnesite orebody which required an innovative approach to process design in order to economically exploit the characteristics of the ore and produce a marketable range of high quality refractory magnesias for a declining world market. High quality natural refractory magnesia must have an MgO content in excess of 95 per cent with a very strictly controlled content and ratio of residual impurities such as calcium, silica and iron. The natural products compete with magnesias derived by chemical extraction from sea water or brines which exhibit very high purity but often lack other characteristics which are of value to refractory brick makers. Since start up in late-1991 QMAG has achieved a remarkable market penetration for both its deadburned and electrofused products with sales for the 1993/94 financial year representing 92 per cent of deadburned capacity and 138 per cent of original electrofused capacity respectively, all at a time when the world steel industry has been in recession.

Jan 1, 1995

By Giannini LM, Carras S

A fundamental problem in mine planning is that of determining the "optimum pit limit" of a mine. This optimum pit limit yields information which is considered essential in the evaluation of the economic potential of a mineral deposit, and in the formulation of long -, intermediate -, and short-range mine plans. Since the mid 1960's a number of mathematical techniques based on the "block model" have been proposed for solving this problem. When applied to large ore-bodies the implementation of these techniques, especially the more elaborate ones, poses considerable computational problems. In this paper we report on our work, done jointly with Systems Research Institute of Australia (SRIA), in devising strategies for overcoming these Problems.

Jan 1, 1986

By J N. Moncrieff

The resource estimation process for the underground Mount Isa Copper Mine has undergone significant change. Block models are now created using a commercial software package as opposed to the in-house software that was previously used. With mineralisation occurring over a strike length of more than 4 km, Mineral Resources for all categories totalled 190 Mt at 2.7 per cent Cu at 31 December 2002. Estimation is by ordinary kriging with two separate models generated to cover the X41 and Enterprise orebodies respectively. The underlying Upper Basement Contact and the silica-dolomite alteration envelope are both used as hard boundaries to constrain the modelling. From a validated block model, grade shells are generated at the appropriate cut-off grade for a given area. The grade shells are depleted for mined voids and subdivided into 30 metre strike length blocks. Application of a SMU criteria and crown and pillar constraints results in failed blocks being culled from the resource inventory. Mineral Resource blocks are further subdivided into resource categories (Measured, Indicated, Inferred) by the Competent Person on the basis of geological confidence, taking account of geological and grade continuity, drillhole spacing and structural complexity (JORC, 1999). A geostatistical æconfidenceÆ category is incorporated into the block model as an additional tool for the categorisation process. The shapes are assessed in concert with a mining engineer to determine whether a reasonable expectation of mining potential exists and if not they are removed from the resource. The final categorised blocks constitute the Mineral Resource inventory and form the basis for conversion to Ore Reserves. The resultant Mineral Resources and Ore Reserves are reported on an æinclusive ofÆ basis.

Jan 1, 2003

The Amacan Copper Project was constructed in the Philippines by a Finnish-Filipino Consortium during the years 1979 - 1982. The project involved a turnkey contract for a mine and a concentrator to process 25 000 tonne per day of porphy- ritic copper ore at a grade of 0.45% Cu. The orebody is located on Mindanao, the southernmost island of the Philippines, in rugged, mountainous terrain approximately 1 000 m above sea level. The adopted design principle was based on an efficient, straightforward installation utilising a minimum number of items of equipment each with high unit capacities. The consortium faced many problems which resulted in lengthy delays in construction and finally led to the client taking over responsibility for the completion of the project. The concentrator was successfully commissioned in July 1982.

Jan 1, 1986

By T Goswami, M Edmondson

Henry Walker Eltin (HWE) are the mining contractors for Gloucester Coal at Stratford mine, which is in an environmentally sensitive area in the Avon Valley, NSW, Australia. Normal blasting at Stratford is done in a æstand upÆ or æbox cutÆ mode to suit the truck and shovel operations. Recently an opportunity of doing a throw blast became available when part of a ramp had to be blasted to accommodate changes to the pit design while not damaging the remainder of the ramp. The objective was to maximise throw into the void in order to minimise excavation costs by reducing the amount of overburden to be moved by the excavation fleet. It was necessary that the best result be achieved while staying within the vibration and airblast limits at a neighbouring property and nearby township. Both objectives were achieved through the application of OricaÆs knowledge of blast design, modelling and i-konTM electronic detonators. The i-kon system was used because of its known benefits in cast blasting and environmental control. The i-kon system provides the blaster with much greater accuracy, control and the flexibility to tailor blast designs. It has been found previously to enhance blast throw and provide cleaner high walls (Brent, 2002). The blast was a success, producing a muckpile with a high degree of looseness and consistent fragmentation, with an average throw to final spoil position of 37.5 per cent. This was achieved without any environmental exceedance. In addition, high speed filming showed that the coal edge had remained largely in place, indicating minimal coal loss. The results exceeded the expectations of HWE Stratford and the overall cost savings to HWE Stratford from this blast were recognised to be substantial. Further throw blasting opportunities at Stratford have been followed using the i-kon system to maximise benefits.

Jan 1, 2003

By Kitzinger F

The economic climate of the Canadian mining industry forced an increased interest in rapid, continuous excavation techniques for hard rock formations. The potential applications and advantages of continuous mining over the present drill- blast-muck labour intensive cyclical methods are considerable. Noranda investigated an electrical technique, Plasma Blasting showing considerable promise for mining hard rock. The background of the technology and the theory of blasting rock with electricity is described. The Plasma Blasting process is based on the fast discharge of stored electrical energy into a small amount of electrolyte, suitably located in the rock. The electrical energy converts the electrolyte into high pressure plasma, which expands very quickly, thereby, generating a shock wave. This shock wave produces a stress field inside the rock, resulting in a blast similar to that made by chemical explosives, but without the deleterious fumes. Noranda is currently blasting boulders of 4-5 tonnes and is at present constructing a mobile, autonomous secondary rock breaker for underground and open pit applications. Tests on in situ hard rock formations will lead to the development of a continuous mining machine. Production rates of 500 tonnes per man-shift could be obtained with such a machine.

Jan 1, 1990

By Misk A

Several logging methods are presently available to the oil industry for the evaluation of formation porosity: the Sonic and Neutron logs are already widely used, the Gamma-Ganmia log is being progressively introduced. The readings of these instruments are primarily a function of the rack-porosity, hence the general term of "porosity tools". Apart from porosity, however, other variables such as type of fluid in the pores, nature of matrix and degree of shaliness have an important influence.The response of each device is a different function of such parameters: therefore, a cci bination of porosity tools can lead to information on these variables in addition to the evaluation of effective porosity.For example, the presence of gas; rather than water or oil, in a formation which is not deeply invaded, will tend to give Neutron derived porosity values which are too 'low; on the other hand, the Sonic derived porosity: value will be too high in such- a case. For the same porosity, the Sonic gives a longer transit time in sandstone than limestone, whereas in the low porosity range, the Neutron will read more counts per second in a sandstone than in a limestone of the same porosity. The presence of shale also affects the readings of the various porosity tools in different ways so that the combination of two or more methods may lead, in some cases; to an evaluation of both the-effective porosity and the shale, content.In conclusion, it may be said that the various porosity tools pre-sently available, are, to a large extent, complementary, and that in many problems the use of two porosity tools, instead of one, is very likely to bring valuable additional information.

Jan 1, 1962

By Patridge A. C

Hydrocyclones have widespread use as classifiers in applications such as mine fill preparation and coal preparation. A fundamental conflict often exists between recovery of all of the valuable material and maintaining the quality of the product. This conflict is a result of a portion of the feed material passing through the cyclone, effectively without undergoing any classification. This paper describes an investigation, undertaken as an undergraduate project in mining engineering at the University of NSW (Brook, 1994), into aspects of cyclones in which supplementary water injection is used in an attempt to reduce the amount of misplaced fine material reporting to the coarse product and hence improve the overall classification efficiency. In particular, the study concentrated on the effects of different modes of water injection. Two methods of introducing wash water into the cyclone body were investigated. A series of tests were performed on a laboratory hydrocyclone having provision for radial water injection at different levels through small orifices in the wall of the conical section, and a preliminary study was made of the performance of a novel cyclone in which the conical section had walls of a permeable polyethylene, permitting a uniform introduction of wash water over the entire surface.

Jan 1, 1995

An understanding of the way that solutes are transported in mining or natural environments is essential to the development of sound strategies for managing waste disposal. Research on miscible pollutant movement in unsaturated porous media is carried out both experimentally and numerically. Results of numerical modelling are obtained by solving the groundwater flow equation and the solute transport equation. The finite element method is employed and comparisons between simulation results and experimental data are found in remarkable agreement.

Jan 1, 1995

By D M. Aranha, A R. Cabral

Theories on the origin of the Itabira iron formation (itabirite) in Quadrilßtero Ferrffero (QF), as elsewhere in the world, are restricted by the apparent lack of adjoining volcanic units, severe syndeformational metamorphism and deep weathering. Besides the three types of iron formations at QF (siliceous, dolomitic and amphibolitic; Dorr, 1969) we include a fourth type initially described as ocherous, goethitic, limonitic or even yellow iron formation. Considering its high magnetite content, it has been described as yellow magnetite itabirite (Pires, 1979). It was reported as formed by the alteration of the dolomitic itabirite (Dorr, 1969) although the anomalous Al2O3 contents are high for normal weathered itabirite. The yellowish magnetitic itabirite occurs at the bottom of the Itabira Iron formation, along the contact with the Batatal schists, and at the top units of the Itabira, within the Gandarela Formation. Within the magnetitic itabirite at the Tamanduß iron ore mine there are metric zones, concordant to the bedding of pillow-like structures, exhibiting a porous core, surrounded by an intermediate, more granular zone with numerous, minute rounded cavities grading to an external, fine-grained zone with much less minute cavities. In the external portions of some pillows a breadcrust type structure, derived by quenching with the water can be observed. In some other zones, such as the Barreiro hill, an outer, vesicular, whitish yellow, 5 - 10 mm thick, band grades to an aphanitic, isotropic band. The vesicles are slightly flattened against the band surfaces. The existence of fragmental layers showing flowage and fragment alignment, kaolinitic laminas and vesicles filled with kaolinite at Barreiro Hill and Capitpo do Mato Mine represent mesoscopic structures, indicators of a possible volcanic origin. Chemical compositions of the magnetitic itabirite from a wide area in QF revealed a relatively high Al2O3 content, consistent with a volcanic origin.

Jan 1, 2005

I take it the character of addresses to conventions, should, following precedent, avoid details, and treat subjects rather from a philosophical point of view so far as they will permit.In the subject about to be treated on, an endeavour will be made to find here we stand as regards the past, in order that we may the better, hope to look correctly in the direction to be followed.It may be assumed that the main object of the Institute is to forward mining interests and the ways in which engineers can aid those interests are many. If all of us were to try to follow many of those interests we should become like" jacks of all trades and masters of none". Mining engineering is consequently subdivided, all are necessary to the common end, and it is on one of those divisions I have undertaken to address you. The subject or steam pumping is a large one, and I regret, not having received such longer notice as would have enabled me to do better justice to the subject, and more respectful regard for yourselves. I must, however, under the circumstances, crave your generous consideration, and hope the topics mentioned may furnish material for discussion and future papers of far more value than this one, Ind.eed, the subject is so illtimately and historically associated with mining that if treated on its merits would be highly interesting or could be made so in more capable hands.

Airblast overpressure legislative limits can be extremely difficult to meet throughout Australia, which has by far the most stringent limits of any nation in the world. As the difficulty in meeting the limits is strongly dependent on the scale of mining, it is not surprising that the Australian coal mining industry is experiencing particular difficulties in meeting these limits. Eight full scale overburden blasts have been modelled with respect to overpressure impact for a strip coal mine, involving both dragline (cast) blasting and pre-strip (non-cast) blasting. Overpressure levels in the range 100 to 125 dBL have been measured at distances varying from 2.4 to 5.7 km, and modelling has successfully estimated both the amplitude and shape of overpressure waveforms to within an average of 1.2 dBL. Typical errors of prediction are around 0.6 dBL. This accuracy of prediction has been achieved by considering the impact of only the face holes, and the accuracy of prediction of both shape and amplitude suggests that it is these holes which dominate the environmental overpressure impact at distances in the range two to six kilometres, for cast and pre-strip blasting operations. Modelling has been based upon the Elemental Overpressure Wavelet proposed by Richards and Moore (2002), incorporating actual hole coordinates, actual delay timing, and assumed delay scatter statistics. The incorporation of delay scatter statistics has been particularly significant, and allows the determination of the range over which the peak overpressure levels are expected to vary. To date, modelling has considered only the use of conventional pyrotechnic delays, though simple adjustment to the scatter definition would allow estimation of overpressure levels, and their variability, with electronic delays.

Jan 1, 2004

By A D. Ferreira, A E. C, A D. Padovezi

The increasing market requirements regarding the quality of products, the enhanced predictability from detailed mine planning, the need for process consolidation and upgrading require continuous investigation on the characteristics of different ore types to be concentrated. This paper addresses the mineralogical and technological characterisation of several itabirite iron ore types and the influence of the composition and mineralogical associations on desliming and flotation. Pellet feed quality and the influence on the major performance indicators, such as weight recovery of slimes, selectivity index, metallurgical recovery, flotation kinetics of iron minerals and gangue is also emphasised. The investigation resulted in a classification of iron ores according to their mineralogical composition, morphology of the crystals, and/or texture and microstructure of mineral particles with respect to desliming and flotation performances.

Jan 1, 2005

George Fisher Mine, near Mount Isa in northwest Queensland, has been producing Pb-Zn-Ag ore since the late 1980s. It consists of two separate underground deposits, George Fisher South and George Fisher North. These two deposits are drilled and modelled separately but are crushed and hoisted as a single stream. The Pb-Zn concentrator in Mount Isa processes ore from George Fisher Mine and Black Star Open Cut, with production also from the Isa Lead Mine until January 2006. This paper outlines the steps involved in setting up a robust reconciliation system for George Fisher Mine, in conjunction with requirements of the Pb-Zn concentrator, Black Star Open Cut Mine and the Mount Isa Lead Mine. Good quality input data and commitment to training have contributed to establishing a robust and effective reconciliation system. Reconciliation data has highlighted several other continuous improvement opportunities.

Jan 1, 2006