Search Documents

The combustion characteristics of Australian coals which contain high inertinite have been studied in a laboratory drop tube furnace and a Thermogravimetric Analyser. The pyrolysis chars and combustion residues were microscopically characterised using a modified coal petrography technique. Results indicated that the overall burnout of inertinite-rich Australian coals under pulverised fuel combustion conditions could be generally within a range of 97 - 99 per cent burnout. The studies showed that poor coal burnout cannot be generally related to high inertinite content in the Australian coals. The extent of coal burnout varies from coal to coal and vitrinite as well as inertinite may contribute to the unbumt chars in combustion residues. Combustion conditions had greater influence over char formation and coal burnout than the coal properties. However, under similar pf combustion conditions, coal rank and coal maceral composition had a strong influence over the coal combustion behaviours and final coal burnout. Simple correlations using coal properties may be used but with caution to determine coal volatile release and burnout at high temperature and rapid heating conditions.

Jan 1, 1991

By H Höft

Today tunnel segment liners are sealed with corner-vulcanised gaskets made of extruded elastomeric compression profiles. The profile geometries and the elastomeric materials have been further developed in course of time to meet the steadily increasing water-proofing requirements. After 40 years of using such compression gaskets, a wide range of proven standard profile geometries and well-known brands can be found on the market. Even so, there is still potential for further developments and improvement, not only with regard to the water-proofing performance. Permanently increasing cost pressure in the segment production plants demands further developments and new solutions with regard to application techniques. This is an abstract only. No paper was prepared for this abstract.

Mar 8, 2011

By I Mason, A Bray, K Smith, T Sindle

Borehole radar is a proven geophysical technology that can be used to map an orebody ahead of mining. This paper will present a case study, where borehole radar is being used within the mining cycle to map out orebody blocks, both as a strategic and tactical tool. Refined equipment and procedures now enables a slimline borehole radar tool to be deployed on the end of drill rods, making it easier and faster to deploy in an underground mine with minimal impact on the mining process. Boreholes are drilled in advance of mining; cover holes to ensure the competence of the hanging wall and geology holes to determine the location and grade of ore are two such examples. All of these boreholes can be entered using a borehole radar tool to map geology and structure ahead. The radar data can provide images of the orebody as well as help detect potential water bearing structures that could impact on safety at a mining face.

Jan 1, 2009

A review is presented of techniques cur- rently in use, or being developed, to enable the determination of virgin rock stress at consid- erable depth (> 1000 m) from small diameter sur- face drill holes (

Jan 1, 1975

Particles finer than 10 um often cause problems in flotation. The current under- standing of the nature of the following effects is discussed: slime coatings on particles, carrier flotation, increased froth stability, entrainment of ultrafine gangue, excess reagent consumption, slower rate of flotation, more reactive surfaces. The review emphasizes the principles underlying these effects rather than details of progress in practical solutions to the problems they cause. The princi- ples of selective flocculation and floc flotation and the various approaches to achieving selectivity are discussed. Hydrodynamic effects on floc growth are reviewed. The evidence suggests that satisfactory performance in the ultrafines fraction will be achieved only by simul- taneously increasing the rate of flotation of the ultrafine valuable mineral and de- creasing the rate of entrainment of ultra- fine gangue.

Jan 1, 1984

By Huber A. L

Research and development into alternate gold and precious metals adsorbents has resulted in the development of a new technology named the AUROSAVE adsorption process (ARGOSAVE'" for high silver con- tent ores). Adsorbents called VITROKELE'" can be tailored for either Gold I (cyanide leach) or Gold III (halide leach) applications. VITROKELE consists of a chemically synthetic adsorbent carried on an inert substrate, often a polystyrene bead. It is suitable for both in- pulp and in-solution use. VITROKELE adsorbent offers certain advan- tages over both carbon and ion exchange resin adsorbents. This paper describes testwork on Australian ores and commercial solu- tions obtained from operating Australian plants demonstrating the kinetic loading characteristics, elution methods and other operating parameters of VITROKELE adsorbent in the cyanide system. Brief reference is made to VITROKELE in the Gold III system.

Jan 1, 1988

Queensland hosts vast deposits of brown and black coal, significant accumulations ranging in age from Permian to early Tertiary. The great diversity of coal resources in the State to some extent reflects the proximity of Queensland to plate-marginal tectonic processes through much of the Phanerozoic eon. Coal is contained within sedimentary basin fills of four fundamental types; 1. extensional, 2. foreland, 3. strike-slip, and 4. intracratonic. Thick (10 m+) though laterally restricted coal bodies are characteristic of extensional and strike-slip basins, whereas coals of more modest thickness but much greater lateral extent are typical of foreland and intracratonic basins.

Jan 1, 1991

By de Brodtkorb MK

Late Cenozoic ore deposits "Precious and base metal-rich" and " Sn-Ag-polymetallic"of Northern Puna are associated either with Middle Miocene dacitic volcanic-dome complexes or with Upper Miocene dacitic-andesitic volcanic centers. Ore mineralogies and their related volcanism are discussed. A strong link is observed between the Cenozoic Metallogenetic Province of Northern Puna and the Southern Bolivia Tin and Polymetallic provinces.

Jan 1, 1995

By Battino S

ABSTRACT' The high gas emissions associated with coal extraction at some-Australian collieries have provided a need to investigate the methods used to predict these gas levels and the vent- ilation requirements for gas dilution. It is generally accepted that the introduction of longwall extraction in particular is associated with complex ventilation planning problems. These problems are made much more severe when the colliery introducing longwalls is already facing high gas emissions even during the development stages. A forecast of likely gas emissions during the longwall mining process indicated possible ventilation problems in maintaining the necessary ventilation levels to satisfy the statutory gas limitations for various production rates. Although there are sound principles used in world recognised methods of gas emission prediction a new approach developed from the findings of the Barbara Experimental Mine in Poland appears most suitable for Australian conditions. This has been applied to an Australian colliery preparing for longwall mining using statistical methods for air

Jan 1, 1983

The disadvantages of the present zinc producing methods, RLE and ISP, are high energy consumption and environmental problems. Therefore, efforts have been directed in Outokumpu Zinc towards the development of alternate routes. One interesting pyrometallurgical process to produce zinc is to inject zinc calcine together with a solid reductant into molten iron, saturated with carbon. This process has been studied by thermodynamic calculations, laboratory tests and mini-pilot test runs at Outokumpu Research Oy, Pori, Finland. The results of these tests are presented and discussed in this paper. The mini-pilot tests demonstrated that over 97 per cent evaporation of the zinc was possible using a reactive coal dust as the reducing agent. The recovery of zinc in the metal phase was at best 88 per cent of input zinc, but only part reported in molten lead in the splash condenser. The final metallic zinc contained at best 98 per cent Zn, the main impurities being dissolved lead and coal carried along with the flue dusts.

Jan 1, 1993

By J Zanganeh, M Ajrash, B Moghtaderi

Application of thermal oxidation is considered a promising technique in reducing fugitive methane gas from ventilation air methane (VAM). A typical thermal oxidiser operates with diluted methane and converts it to less potent greenhouse gases. However, having a thermal oxidiser in the vicinity of the coalmine exhaust shaft is a major safety concern as its high operation temperature increases the likelihood of accidental fire and explosion. The aim of this study is to investigate the application and effectiveness of side venting technique in reduction of deflagration consequences caused by methane gas. To address this importance a series of experiments were conducted on a detonation tube designed and fabricated as part of larger scale VAM Abatement safety project. The experimental work was carried out into two stages: examine the flame and explosion properties in a large-scale detonation tube to get reliable data; and then design and employ a venting system into the detonation tube to verify the effectiveness and performance of the venting against the flame and explosion.Results corresponding to this study show that the side vent duct with venting coefficient magnitude of 37 had a significant influence on methane flame deflagration and the explosion characteristics. The maximum pressure rise at the detonation tube reduced approximately 20 per cent to 32 per cent by applying the side venting duct. Also, the data shows that the venting damped the pressure oscillation after the flame deflagration which eventually reduced the system instability. Finally, by applying the venting technique the expected level of damage due to the dynamic pressure reduced to the level of limited building damage.CITATION:Ajrash, M, Zanganeh, J and Moghtaderi, B, 2017. Application of side venting technique in mitigation of methane – air explosion and flame deflagration in ventilation air methane, in Proceedings Australian Mine Vent Conference 2017, pp 153–258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Richmond AJ, Allan J

The use of long-hole in-seam drilling techniques for seam gas drainage ahead of mining was introduced to the Australian coal industry by ACIRL in mid-1981. ACIRL's research program has involved the development and demonstration of drilling and borehole survey technology in addition to evaluating the gas drainage potential of long-hole in- seam boreholes. This paper presents the results of the long-hole drilling carried out to date in the Illawarra District of the New South Wales coal fields. Drilling experience in relation to both vertical and horizontal directional control of the drill string, drill performance and borehole survey techniques are discussed. In addition, results of gas drainage effected by the long boreholes are presented. Future potential and requirements for further development of this technology are Reviewed.

Jan 1, 1982

By Thimons E. D, Derick R. L

In early June, 1986, a fire of unknown origin erupted in one of several main entries of a coal mine located in southwestern Colorado. The fire was aggressively fought with high-expansion foam. As a result of several strategic decisions, the fire appeared to be held in-check. Unfortunately, sufficient quantities of foam were unavailable and as soon as the foam was depleted, control of the fire was lost. To prevent further damage and the possibility of an explosion, all entries to the mine were sealed.

Jan 1, 1988

By B Cooper

During the design of a new production facility for a greenfields or significant brownfields expansion many design decisions are made driven by an unquestioning objective to achieve 'lowest cash-cost' production costs. In many cases this translates to a design and operating philosophy based on largest-available, single-line equipment. Although acknowledged as an approach that is efficient from an operating cost perspective does this approach always maximise shareholder value? There is an increasing awareness in the mining industry of the value of project flexibility, robustness and value options. The design of a new production facility creates a window of opportunity which should be structured to ensure that project value options and robustness are understood and exploited. This requires the use of emerging valuation methodologies, such as Value-at-Risk and Real Options, as well as tried and trusted NPV/IRR approaches. The paper provides an overview of the basis and application of these less well known techniques in the context of metallurgical plant design. Design guidelines that demonstrate how value options and flexibility can be quantified from both a risk and value perspective are presented. Issues such as use of single versus multiple line equipment, optimum cut-off grade and improved exploitation of the inherent variability of the orebody are also examined. Finally the management issues and approaches to achieving this will be briefly discussed; for example it is common during project development to drive towards increasing certainty as rapidly as possible to facilitate 'accurate' estimation of costs. Understanding and exploiting value options requires a project culture that tolerates, and revels in, ambiguity and uncertainty û something that would make many project teams uncomfortable!

Jan 1, 2008

In epithennal deposits changes in the character of mineralization in depth and time are conspicuous and abrupt at the interface between supergene and hypogene zones. As the reaction zone migrates downward as a consequence of surface erosion, previously deposited minerals are placed in unstable chemical enviromments and dissolved. This reaction takes place at the base of the epithermal precious metal zone. Examples at Cerro de Pasco, and Casapalca, Peru; Carlin, Nevada; and porphyry copper-gold deposits are cited.

Jan 1, 1991

By J Parmenter

Issues around water û its quality, use, availability and environmental value û can be a major point of tension between mineral projects and local communities. Failure to manage these issues appropriately can jeopardise the obtaining of regulatory approvals for new projects and place at risk the æsocial licence to operateÆ of existing operations. Conversely, there may also be significant opportunities for companies to engage constructively with communities over water issues and to make a positive contribution to the sustainable development of these communities. Using case studies, this paper will explore the various types of social risks and opportunities associated with water and mineral resource development and identify key learnings relating to the management of these issues.

Jan 1, 2006

The Olympic Dam Mine is a large, mechanised, underground operation currently producing 2.2 million tonnes-per-year of copper/uranium/gold ore. The mine is accessed via one shaft and one service decline. An additional 13 raise bored ventilation shafts have been completed to-date.Ventilation requirements are stringent in order to provide adequate dilution and removal of diesel fumes, radon gas/daughters and heat generated from both engines and wall rock.Due to the nature of the orebodies, the mine workings will continue to expand laterally necessitating the addition of at least one major surface raise every year.

Jan 1, 1992

By Ishijima Y, Goto T

Displacement Discontinuity Method (DDM), which was originally developed by Crouch,S.L., is a powerful tool to calculate mechanical disturbances due to tabular excavations. Three topics on DDM applications to strata control problems in Japanese deep coal mines are described. First, is numerical simulation of microseismicity induced by longwall mining in Horonai Coal Mine. Microseismicity in the mine had been monitored by a mine-wide seismic ar- ray. Location of microseismic events and in- tensity of seismicity were well simulated. In the simulation procedure based on DDM, first, zones where a failure condition is satisfied by the advance of mining are detected. Then, the seismic moments, which indicate the inten- sity of seismicity, at the failure zones are evaluated. Second, is prediction of the shaft damage due to mining in Sumitomo Akabira Colliery. In this mine, the limit angle of the shaft pillar was changed from 600 to 800 to increase the amount of minable coal volume without increas- ing mining depth. Displacement of the shaft axis has been measured to assess the damage due to mining around the shaft pillar. In the calculation based on DDM, a fault intersecting the shaft and the ground surface are con- sidered. Observed and predicted displacement of the shaft axis agreed well.

Jan 1, 1992

Intermontane valleys form unusual features of compressive mountain belts both in the sharp topographic break they represent and in the strike-slip displacements often associated with the valleys. Such strike-slip motion seems hard to reconcile in the actively deforming Andes where reconstructions have indicated nearly perpendicular Cenozoic plate convergence. Detailed study of a part of the Argentine Andes between latitude 31-33¦S suggests that, although strike-slip displacements may have largely created a prominent intermontane valley system, no Holocene strike-slip displacements are observed amid the relatively active compressional deformation along the mountain belt flanks. New plate reconstructions, treating the Nazca plate as two microplates separated by fractures along the Nazca Ridge, predict large components of strike-slip motion between the South American and Nazca Plates for the period from 10 to 5 Ma. These reconstructed plate motions are consistent with strains derived from recent kinematic analyses of minor faults along the southeast margin of the Puna plateau and the general timing of tectonic phases in the Andes.

Jan 1, 1987

We are all no doubt aware that with today's high costs it is more important than ever to get the maximum possible return on capital invested in the mining industry. Screening is an important and often costly process in the size classification of industrial minerals and for this reason alone it is essential for both managers and operators to fully understand what type of screening equipment is best suited for a particular application and why. The advent of elastic materials such as rubber and polyurethane have added a new dimension to the process of screening. It is important to understand why the physical properties of these materials can be of benefit in the screening process, and recognise which type of screening applications best take advantage of these orooerties.

Jan 1, 1984