Search Documents

By Hyde L. J

Blasting is one of the available technologies to be employed in underground excavation systems. In many instances it can be the only technology which is suitable. The recent moves towards more mechanised working systems is resulting in a reduced awareness of new blasting practices and technologies on the part of many excavation engineers. Recent developments in blasting systems can be utilised to significantly improve operating efficiency, reduce total cycle times, better comply with regional environmental constraints and reduce the total cost of underground excavation. Blasting is and will remain, a very adaptable and exciting alternative which is far from boring.

Jan 1, 1987

Sheaves are a critical safety component in a winding system and are expected to survive such extreme loading events as rope break. Sheave designs have often been developed and evolved empirically, consequently many existing sheaves are not necessarily subjected to the detailed analyses that are possible using todayÆs design tools. The design philosophy for sheaves is that the rope should be the weakest link in the system so that associated equipment can function safely for any load up to rope break. A number of failure mechanisms must be considered, but buckling is often prominent. During the course of investigating the feasibility of upgrading the hoisting capacity of a winding system, the capacity of all critical components was reviewed. The sheaves in the system were found to have insufficient spoke buckling capacity for the specified rope. A proposal to increase the spoke buckling capacity by connecting spokes together using a simple tie arrangement was evaluated and found ineffective. An alternative tie arrangement concept was developed and evaluated and shown to be adequate. This paper describes the finite element model, analysis approach and results for the original sheave and the two modifications. The contribution of the sheave rim to the total buckling capacity is evaluated. Some practical issues for spoke tie modifications are discussed.

Jan 1, 2005

By Walker E. R

IN the early age of steel it was made hy what is known as the cementation proeess, in which wrought iron was embedded in charcoal and heated in a mufflc furnace to a tcmperature of approximately 1100° C. for varying lengths of time, the length of time depending upon the amount of carbon (or better known in thosedays as the degree of hardness) required in the finished product.By this process the resultant product obtained was not of uniform quality, and because of this uncertainty of quality Huntsman was induced, in the year 1740, to introduee what is known as the crucible process.This process consisted of cutting into small pieces the product of the cementation process, placing these pieces in a crucible, and melting them down with the aid of a eoke-fired furnace, after which the molten metal was cast into suitahly shaped ingots, from which could be hammered any desired shape.A section of crucible furnace is shown in Fig. 1. By this means a product, very uniform in character, was produced.The process is still in use, but, owing to its high operating cost, it is mostly eonfined to the production of very high-grade carhon and alloy steels. Its position to-day as a producer of these high-grade steels is, however, being very seriously challenged by the electric process.It was owing to the excessive cost of crucible steels and the need of producing a steel in commercial quantities and at a reasonable cost, that led Sir Henry Bessemer to introduce what is known as the Bessemer process.

Jan 1, 1930

By Morrison R. D

This paper describes major events in the design, construction, camtissioning and operation of the Elura concentrator. It covers the period fran September, 1974 when laboratory testwork on drill core cotmenced to March, 1983 when the concentrator catmenced operation on run of mine ore following successful completion of initial ccnmissioning tests. The concentrator was designed to treat 1.1 million tonnes of lead-zinc-silver ore per year with a plant availability of 89 per cent. This treatment rate has been achieved for test periods.

Jan 1, 1983

By Cleghorn JH

Underground mining operations on Kalgoorlie's Golden Mile were suspended in 1976, suffering the combined effects of low gold prices and grades. A subsequent substantial increase in the gold price led to the decision by Kalgoorlie Mining Associates to reopen their mines in 1979. The two shafts selected for access required excessive maintenance. The geological assessment and development parameters prescribed have been successfully used to establish reserves to maintain production at a 390 000 tonnes per annum rate. While ore reserve grade is being maintained from primary stoping sources, supplementary lower grade ore is drawn from remnant pillars and stopes at lower cost.Performance by the workforce has reached levels previously attained and a record tonnage was hoisted in the fourth year after recommencement.Keywords : Golden Mile lodes, geological research, payruns, cut and fill, mill holes, gold price, ore grade, amalgamation.

Jan 1, 1984

As the worldÆs population and global standard of living increase, the role of metals in the economy will not diminish in the 21st century, despite substitution and dematerialisation trends. Industrial Ecology is an emerging science that attempts to bring together physical, biological and social scientists and develop the tools for good management of the planet in the long run. In engineering terms, Industrial Ecology is defined as the reconfiguring of industrial activities with full knowledge of their environmental consequences. Production and use of materials must take into account the needs of both market and environment. Dispersive uses of metals will be phased out, as is being done with lead in gasoline, and post-use recovery of materials and energy will increase. This will result in an advantage for metallurgical processes that can use as feed materials concentrates as well as metal scrap and waste streams, such as bath smelting processes and slag resistance electric furnaces. The paper also discusses how metal extraction technologies, developed in the 20th century to provide essential materials to humanity, can be applied for the benefit of both mankind and environment in the 21st century.

Jan 1, 2000

By La Brooy S R, Fenton K

A low grade copper flotation tailing from Telfer containing 1.2% Cu as chalcocite and cuprite and 5 gt-t Au was leached with ammonia, cyanide and ammonia-cyanide mixtures to extract copper and/or gold. Direct cyanidation extracted both copper and gold but consumed about 30 kgt 1 NaCN. Pre-leaching the tailing with an aerated ammonia solution containing 28 kgt 1NH3 and 17 kgtl(NHa)2S0a at pH 10 readily extracted up to 95% Cu in about 6 hours under optimum conditions. However pH and total ammonia concentration were critical factors. Subsequent cyanidation ex- tracted 80% Au using 6 kgt NNaCN. Ammonia-cyanide mixtures werefound to selectively leach gold over copper depending on the concentration and relative proportion of NH3 and CN. The best composition for leaching up to 80% Au from Teller tailing was 1.6 kgt t NaCN and 1.1 kgf 1 NH3 in the presence of 0.3 kgt t Cue+. Such a mixture left only 50 mgL-1Cu in the final solution after precipitation of some of the initially dissolved copper.

Jan 1, 1991

By Amanatidis A

In this paper, the kinetics of iron precipitation as sodium jarosite from aqueous solution is investigated. The determination of the reaction mechanism is attempted based on the experimental data of iron removal as a function of time, without using the characteristics of the precipitate.Experiments at the temperature range from 50° to 95°C were carried out with initial conditions of iron concentration IQ g/L, sodium sulphate concentration 25.44 g/L, sulphuric acid concentration 3.68 g/L, pH = 1.5 and agitation rate 600 rpm. Temperature greatly and positively influences iron precipitation from the solution and this is accompanied by pH decrease. The activation energy was determined using the maximum values of the precipitation rate, which were evaluated by polynomial fitting of the sigmoidal shape experimental curves, and it was found to be 44.37 kcallmole. The determination of the rate-controll ing mechanism was based on some criteria used for the discrimination among the three probable mechanisms of precipitation (diffusion, mononuclear nucleation, polynuclear nucleation). These criteria utilise various funetions of the recovery 'a' of iron precipitated versus time, the most important of which are the chronomals. The results of the kinetic analysis procedure showed that the polynuclear nucleation growth mechanism controls the precipitation of iron as sodium jarosite. This was confirmed by the high value of activation energy, excluding diffusion as the controlling mechanism.

Jan 1, 1993

By G Brooks

The control of phosphorus in steelmaking is one of the famous challenges of pyrometallurgy. It is well established that highly basic slags, the presence of FeO in the slag and lower temperatures (less than 1650°C) are favourable for phosphorous removal. The thermodynamics of this reaction have been extensively studied under laboratory conditions and the general trends confirmed through industrial trials. However, in general, phosphorus slag/metal distributions measured in industry are far from equilibrium and quite specific to the oxygen steelmaking technology being used. This variability was quantified by Urban, Weinberg and Cappel (2015), who found that the phosphorus partition ratio measured in plants varied with blowing practice, stirring intensity and even converter life. Some recent kinetic studies by Gu, Dogan and Coley (2017) have shown how the kinetics of these reactions vary with FeO content and dissolved sulfur at the droplet scale. A global kinetic model by Rout et al (2018) provides meaningful predictions of where dephosphorisation occurs in an industrial basic oxygen furnace (BOF) and some recent heat transfer modelling by Madhavan et al (2021, 2022) implies that temperature difference between droplets and slag has a role to play in explaining why equilibrium is not achieved. This paper will review the current state of knowledge and provide suggestions on predicting phosphorous removal for industrial operations and how greater removal could be achieved.

Jun 19, 2024

By Menne D. M, Ladyman R

Camel Creek Mine operated by Lynch Mining Pty Ltd is located 65 km west of inghain and 160 kin north west of Townsville in North Queensland. (Figure 1). The Camel Creek gold mineralisation was discovered in mid-1987 in an area previously known for its tin workings. Mining commenced in January 1989 after an oxide reserve of 1.2 million tonnes @ 2.1 g/t gold had been delineated. The first gold pour was in May 1989. The mine developed into a medium sized open cut operation, with full site facilities. The initial mining rate was 500 000 tpa utilising run-of-mine (ROM) heap leaching to recover the gold. By the end of 1990 the wider orehodies were mined and efforts were focused on the narrow orebodies, of width typically less than three metres. Smaller earth moving equipment was employed to selectively mine the narrow orehodies leading to a decrease in the mining rate to 200 000 tpa. The Red Gold deposit (80 000 tonnes « 3.0 g/t to 18 in vertical) was mined in mid-1990 and ore was hauled approximately 8 kin to the Camel Creek heap leach operation. The ore was hauled in a dedicated campaign after being stockpiled. The cost of dedicated ore haulage ensured that only the more exceptional of the remote orebodies could be mined in this manner. The Golden Cup orebody, some 20 km from Camel Creek, was too distant to permit ore haulage. However, this prospect contained sufficient gold (initially 90 000 tonnes @ 3.0 g/t) to warrant the installation of a small mobile adsorption facility. Construction of the second heap leach operation commenced in late-1990. Gold production commenced in early April 1991. Mining of several smaller orebodies remote to the second heap leach facility has been undertaken and further mining is planned. This paper outlines heap leaching practice at Camel Creek Mine and summarises the success of the Golden Cup heap leach.

Jan 1, 1994

By Grant J

In surface mining, significant improvements in efficiency can be obtained through greater control over the formation of the muckpile. By tailoring the muckpile shape and its looseness to the requirements of the excavating equipment savings can be rea- lised through increased production, machine life and reduced maintenance. For instance, one open cut coal mine has recently estimated that a 2001o improvement in its front row throw would realise $320,000/year savings in rehandle costs alone. Previously greater throw has been achieved by increasing the powder factor through increased quantity of explosive or by drill- ing a larger number of holes-both at a significant cost penalty. However a recent series of experimental blasts demonstrated that it was possible to achieve a twofold increase in the distance of throw of a single row blast by simply changing delay timing alone. The Nobel Electronic Delay Detonator was used to provide the timing flexibility and control required for a thorough study of the effect of blast timing on heave. Whilst it is well accepted that the front row of a blast dominates the extent of throw, it was also found that the profile of the blast could be significantly altered. To date, the general consensus has been that the muckpile for- mation from a blast is a function of the blast geometry, the rock type, the explosive and the initiation sequence. Typically the geometry, rock type and initiation system have a far greater impact than the explosive type. This has been demonstrated by many high speed film studies. However the extent of influence via initiation has rarely been fully evaluated, owing largely to the limited control offered by conventional detonators.

Jan 1, 1988

By Reilly L, Worner H. K

The EnvIRONment process has been developed to treat steel works dust and organic wastes simultaneously. A pelletised feed is fed into a special DC electric furnace, the pellets becoming immersed in a molten slag above a carbon saturated bath. The iron oxide in the pellets is reduced and carburised whilst the organics are broken down to carbon monoxide, carbon dioxide, hydrogen and water vapour. Volatile metals are vapourised and collected in the baghouse. Over two years of trials in a 100 kg DC electric are furnace has brought the process to the stage where it is ready for commercialisation.

Jan 1, 1995

The BLEG (Bulk Leach Extractable Gold) technique is a semiquantitative measure of cyanide extractable gold contained in a sample. A 5kg sample is leached in cyanide solution for 24 hours and gold is precipitated out of the pregnant solution using zinc and assayed by AAS. The detection limit is reported as ppb (parts per billion). Telfer is located 1300km north north-east from Perth in the Great Sandy Desert. The climate is one of hot summers with irregular rainfall and mild winters. A large portion of the area is covered by aeolian sand and seif dunes with poorly developed drainage, rare outcrop; topographic relief is a maximum of 96m. Poor outcrop and poorly developed drainage render conventional stream sediment sampling and soil geochemistry inadequate. Therefore a technique providing a minimum number of samples with maximum accuracy and sensitivity was needed. Consequently BLEG orientation surveys were conducted over the Telfer Mine area in 1983, 1984 and 1985.

Jan 1, 1988

Welcome to Mount Isa- my home city and without doubtthe base for what promises to be the most exciting mineral development yet seen in Australia.Mr. Chairman, it also gives me great pride to representthis area in the Queensland State Parliament as well as being the Minister for Minerals and Energy in the Queensland Government.Mount Isa is now part of the Australian mining industry folklore.It is all what a good mine is all about. It is. all what a good community is all about.

Jan 1, 1993

By Johnson N. W, Quast K. B

Over the years there have been occasional references in the literature to the activating effect of cyanide in galena flotation with xanthates. These have usually been associated with the processing of lead-zinc or copper-lead-zinc ores. Bubble contact curves for the pure galena-xanthate system show a flotation edge at pH 10.4 independent of sodium cyanide concentration which was thought due to hydroxyl ion, not cyanide ion.Flotation tests were conducted on samples of Mount Isa lead-zinc ore using varying concentrations of sodium ethyl xanthate and sodium cyanide. At low collector concentrations, galena recovery kinetics improved with sodium cyanide addition, and the higher the cyanide concentration, the higher the galena recovery rate. At higher collector concentrations, galena recovery rate was independent of sodium cyanide addition.For a given collector addition, the lead grade-recovery curve shifted to an improved position with increasing sodium cyanide level. For the same recovery there was an increase in the lead grade with increased sodium cyanide addition, and this increase was most dramatic at high sodium cyanide concentrations.The presence of sodium cyanide during the grinding of Mount Isa ore caused surface passivation of the iron sulphides and possibly the sphalerite.These sulphides, therefore, reacted with less of the oxygen present in the pulp, hence more oxygen was directed to the surface of the galena. This resulted in an enhancement in the total amount of xanthate adsorbed on the galena that is reflected in the improved flotation response of that mineral.

Jan 1, 1990

Automatic sampling and weighing of copper sulphide concentrate produced on Bougainville Island (PNG) is described. Contained metal weights gave satisfactory agreement with buyer's results after the introduction of polyethylene lined sealed aluminium foil bags for transport and storage of assay samples. Paper bags used previously for this purpose permitted oxidation of the sulphide concentrate and thus caused lower assay values.

Jan 1, 1976

By Kewu W

Kaolin used as an industrial mineral, especially that in the paper-manufacturing industry, must be of fine size, with high brightness, a low impurity content, and good crystal shape. However, in most kaolin deposits there are various impurities which have a very bad effect on the quality of the kaolin. Therefore, it is necessary to remove these impurities from kaolin ore. Owing to their similar surface properties, the separation of kaolin and iron oxide minerals, especially microkaolin and iron oxide minerals, has been regarded as difficult. The iron oxide minerals often intergrow with kaolin in fine and complicated forms, such as thin films, which make separation difficult. In order to overcome this difficulty, many workers have suggested various treatment methods and obtained great success. Based on research work by Fuerstenau (1980), Huang, Li and Hu (1984), Hui and Wei (1991), Shergold (1978), and Zambrana et al (1974), we have investigated a two-liquid flotation technique for iron removal from kaolin and obtained some success.

Jan 1, 1993

By McAuley T. J

Computer software is an integral part of mining operations today with many sites using six or more software packages on a daily basis. However, the use of these different programs generates the need for substantial staff training. The current trend toward large integrated packages to solve this problem is counter-productive because the relatively small companies producing specialised mining software do not have the resources to develop quality software with all the required features. Software standards are being proposed by various parties but recent history indicates these will be unsuccessful. An alternative approach is suggested using the various standards which have been developed for the Windows operating system.

Jan 1, 1995

By Fuller P. G, Dugan K. J

Artificial support can be used to improve wall stability in open pit mines. This is examined for a particular case where the factor of safety for a slope is kept constant by using artificial support as the slope angle is increased. It is demonstrated that the savings in excavation generally exceed the cost of support. However, in order to correctly judge the eco- nomic impact of artificial support on the project, all the elements relat- ing to the use of artificial support must be taken in account.

Jan 1, 1989

By Laird CH

Large quantities of brown coal are excava ted from open cut mines in the Latrobe Valley to fire the base load thermal power stations of the Victorian Electricity System. Most of the coal is removed using bucketwheel excavators which have been modified or specially designed for the conditions encountered. The actual digging efficiency of the bucketwheel excavator is strongly influenced by such factors as wheel speed, slewing speed and tooth design and arrangement. The coal deposit, although not difficult to work, is not uniform and the operation of the machine is influenced by the stability re- quirements of the excavation face.

Jan 1, 1978