Search Documents

The Telfer Underground sublevel cave (SLC) Operation is located approximately 850 m below surface. The cave was designed to propagate through an old decline which was initially used to monitor the cave. There was a requirement to install air blast plugs at two locations in the old decline in order to isolate any potential air-blasts from the active workings in the event of the rock mass collapsing into the cavity. There was a further requirement for an air-blast plug in another section of the mine where there was a risk of the cave intersecting an old workshop and providing an air-blast pathway through an abandoned incline. The design criteria for the plugs was that they should withstand the design air blast loading, be free draining, cost effective and easily constructed with the mining expertise available on site. A plug consisting of grouted mullock was considered robust and least challenging to construct. For the purpose of estimation of maximum air pressure on plugs, it is supposed as a worst case that the rock above a cave falls as an airtight piston onto the top of a muck pile, forcing air into it and also mine workings intersected by the cave. Airflow through the muck pile is governed by Ergun's equation for turbulent flow. In a time-stepping integration scheme, transient air pressures and velocities are calculated according to equations of thermodynamics, in the cave and at intervals along intersected drives by means of a finite difference spatial discretisation. The ability of plugs to withstand computed pressures is assessed by finite element elastoplastic analysis. This paper outlines the rationale for potential air blast loading, calculation of transient air pressures, plug design and analysis of plug behaviour. The plug construction method is also discussed.

Nov 25, 2010

By B J. Beven, A Harris, L Balzan

Fortescue Metals Group flagship operation, Cloudbreak, is located in the Pilbara region of Western Australia. The mine is capable of delivering an annualised production rate of 40 Mt/a. Positioned 50 km to the east of Cloudbreak is Fortescue’s Christmas Creek operation, which has a combined processing capacity in excess of 50 Mt/a. Following on from these successes, Fortescue advanced development of its western Pilbara mines at the 60 Mt/a Solomon Hub. These processing installations place Fortescue in a strong position to deliver on a guidance of between 155–160 Mt/a for financial year 2014/2015.As Fortescue enters a phase of asset consolidation and debt repayment over expansion, the business is commanding stronger performance through enhanced plant operating practices and mine site cost reduction initiatives. To this end, the strategic placement of instrumentation is an area being given greater consideration. Access to real-time information pertaining to conveyed materials is of major interest to operators for making timely process control decisions. Fortescue has recognised the importance of accurate and up-to-date process information about their ores and hence, has adopted the use of Scantech’s Geoscan mineral analysers at two of their mines.There are two Geoscans at Cloudbreak; one on the ROM feed conveyor and another on the final product conveyor. These allow the in-feed material grade characteristics to be assessed. Moreover, the final product stream can be monitored to ensure product quality is maintained within acceptable quality tolerances. A third Geoscan is installed at Christmas Creek mine on a conveyor that transfers final products to Stockyards.This paper discusses the use of the Geoscans in these installations, including benefits to Fortescue’s operations, as well as functional considerations such as the impact of maintenance and calibration. A discussion of recent advances by Scantech is provided including enhancements to the calibration process and minimising plant downtime, along with a summary of results obtained.CITATION:Balzan, L, Beven, B J and Harris, A, 2015. Geoscan online analyser use for process control at Fortescue Metals Group sites in Western Australia, in Proceedings Iron Ore 2015, pp 99–106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By S Mitra, D O’Dea, N Barrett, S, T Honey, M M. Hoque

The steel industry is currently exploring hydrogen-enriched blast furnace operations as a means to reduce the greenhouse gas emissions. However, there is a need to investigate the gas permeability behaviour of mixed burdens comprising of lump and sinter as the current knowledge regarding their behaviour is limited, particularly with regards to hydrogen enrichment. In the present study, a series of interrupted softening and melting (S&M) under load tests were carried out in a hydrogen rich gas environment (~15 per cent) in the temperature range from 1000 to 1300°C by placing different types of ferrous ore layer including Newman Blend Lump (NBLL), sinter and sinter-NBLL mixed burden in between two coke layers. X-ray computed tomography (CT) was then used to scan the interrupted test samples. Scanned images were first analysed using an image processing workflow implemented in ImageJ and the material simulator GeoDict (v2022) to segment different phases such as coke, ferrous and void based on their grey scale values. A quantitative analysis was then performed on the segmented images to estimate the phase volume fraction as well as bed permeability. Bed void fraction thus obtained agreed well with the bed contraction data obtained from the S&M test. It was further noted that both ferrous layer void fraction and bed permeability decreased linearly with increasing temperature for all ore samples. The mixed burden voidage changed in a similar fashion to the sinter, demonstrating a high temperature interaction between the two materials

Sep 18, 2023

An Integrated Geology-Mine-Plant and Eco-Efficiency Simulator for Anglo Platinum's Evaluation and Operational Improvement Initiatives

Sep 13, 2010

By R McCarthy, P Hawke

FerrAus Ltd's Robertson Range and Davidson Creek Projects are located in the Hamersley Province about 100 km east of Newman, Western Australia. Significant iron mineralisation defined by an aggressive exploration program within the Marra Mamba Iron Formation is shallowly north dipping at Davidson Creek, and mainly shallowly east dipping at Robertson Range, forming part of a regional scale anticline with the granitic and greenstone basement of the Sylvania Inlier as its core. With minor exceptions, the stratigraphy is comparable with that seen in the main Hamersley Basin. Granite and greenstone basement rocks of the Sylvania Inlier are unconformably overlain by shales and volcanic rocks of the Fortescue Group. The overlying Hamersley Group is locally represented by interbedded chert, banded iron-formation (BIF) and shales of the Marra Mamba Iron Formation (Nammuldi, MacLeod and Mount Newman Members), and dolomites, cherts, BIF and shales of the Wittenoom Formation. Iron enrichment occurs predominantly in the Mount Newman Member, and to a lesser extent in the West Angela Member of the Wittenoom Formation. Enrichment varies from 20 - 30 m in thickness in elongate bodies up to 3 km in strike length, and generally thins down dip. At Davidson Creek iron mineralisation is a haematite-goethite-ochreous goethite assemblage, while at Robertson Range this assemblage is consistently overprinted by a later, goethitic alteration related to 'hardcap' weathering. Near surface hardcap alteration in both project areas comprises more siliceous, aluminous and vitreous goethite. Initial exploration completed by Rio Tinto Exploration between 1999 and 2001 indicated the potential for about 20 Mt of iron mineralisation at Robertson Range. Since 2005 a detailed exploration program undertaken by Australian Manganese Pty Ltd (a wholly owned subsidiary of FerrAus Ltd) has defined a global indicated and inferred resource totaling 164.4 Mt at 58.6 per cent Fe (ASX: FRS 17 April 2009).

Jan 1, 2009

By R A. Pax, B Cornish

"Although it is well known and easily experienced that the feed size distribution influences the throughput and stability of operation of a semi-autogenous grinding (SAG) mill, the details are poorly understood since it is often only the input and output measurements that are used to identify unfavourable in-mill conditions. Load cells and power monitoring are sometimes used but are generally poor indicators of the mechanisms that lead to such unwanted conditions.At the MMG Century operation a 12-microphone array around the SAG mill using non-contact acoustic measurement methodology has been used to diagnose the in-mill conditions to facilitate improved throughput and stability of operation. Use of acoustic measurement and control has provided a demonstrated increased throughput of at least 20 per cent as well as improved stabilisation of the mill. Since the information derived from the acoustic noise from a mill allows discrimination of the behaviour of the steel balls and the rock, a number of in-mill conditions can be identified with signals that include toe and shoulder angles, water holdup and the ball to rock ratio.Feed size variations, measured online with an imaging system, have been used to determine their effect on the internal charge behaviour. It has been found that circumferential segregation of steel balls and rock occurs as well as poor mixing of large rocks. Both of these effects are not conducive to optimal breakage rates of different size fractions. Longitudinal segregation effects also occur. This paper presents and discusses these results and illustrates how the new acoustic knowledge can be used to manage and improve mill operation and stability.Citation:Pax, R and Cornish, B, 2016. Understanding Size Effects of Semi-autogenous Grinding (SAG) Mill Operation as a Pathway to Solving Feed Disturbances - Case Study using the MMG Century SAG Mill, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 321–330 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

In considering the organization of research, it is necessary to know just what research is, what objects are in mind when setting out to conduct research, and what are the functional units which are required to enable a coordinated effort in research to proceed.The dictionary defines research in the following terms: Laborious and patient search, as for truth, diligent inquiry or examination in seeking facts or principles; inquiry, scrutiny; to search or examine with continued care; to seek diligently; to search again; to examine anew.This is, of course, simply a formal definition, but the reference to "labour", "patience" and "diligence" should be noted.The following quotation from an answer to the question "What is Research?", published recently in a technical journal, puts some life into the formal definition:- Essentially, it (Research) is nothing but a state of mind a friendly, welcoming attitude toward change. Going out to look for a change instead of waiting for it to come. Research, for practical men, is an effort to do things better... The research state of mind can apply to anything: personal affairs or any kind of business, big or little. It is the problem-solving mind as contrasted with the let-well-enough-alone mind . . . It is the "to-morrow" mind instead of the "yesterday" mind. Note the statements that: Essentially, it (Research) is nothing but a state of mind, and the research state of mind can apply to anything.

Jan 1, 1950

By B Chapman, R Nievergelt, J Hill

A major component of Sydney’s new South West Rail Link project is the Hume Highway Underpass (HHU), an 80 m long twin track mined tunnel excavated at a depth of just 5 m below the pavement of the Hume Highway; one of Australia’s busiest road corridors.In order to ensure a safe and efficient construction of the underpass without disruption to the Hume Highway traffic, design of the HHU required specific focus on the prediction and control of ground movements. This paper describes the design and construction solutions adopted in response to these challenging constraints. The paper also provides discussion on the observed behaviour of the underpass during construction and the results of a back analysis that was undertaken during construction.CITATION:Hill, J, Nievergelt, R and Chapman, B, 2014. Design and construction of Sydney’s South West Rail Link Hume Highway Underpass, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 375–386 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By A M. Lechner, V Glenn, M Edraki, D R. Mulligan, C Unger

With more than 50 000 recorded abandoned mines in Australia, effective management strategies are needed to prioritise and manage health, safety, environmental and socio-economic risks and opportunities. This paper reviews international leading practices for abandoned mine management and identifies key issues that need to be addressed in the Australian context. As well as the academic literature, this review draws on a 2008 global legacy site survey and forum in 2008, a Churchill Fellowship study of abandoned mines and the recently released æStrategic Framework for Management of Abandoned Mines in the Minerals IndustryÆ (MCMPR/MCA, 2010).A conceptual model was developed to identify the relationship between key issues affecting the management of abandoned mines in Australia. The conceptual model is then used in the development of a maturity chart which draws on risk management principles to provide leading practice guidance for abandoned mine managers, jurisdictions and stakeholders. The maturity chart approach for risk management has been successfully used elsewhere to evaluate safety, environmental and socio-economic maturity.CITATION:Unger, C, Lechner, A M, Glenn, V, Edraki, M and Mulligan, D R, 2012. Mapping and prioritising rehabilitation of abandoned mines in Australia, in Proceedings Life-of-Mine 2012 , pp 259-266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By C Armstrong, B Wentzinger

Upstream embankment raises often represent the lowest cost option for increasing the capacity of tailings storage facilities (TSF), but also pose the highest stability risk due to constructing on top of previously deposited tailings.This paper presents an overview of key aspects in the geotechnical investigation and design of upstream raises and some recent lessons learnt from experience across a number of TSFs in Australia. A summary of recommended field investigation and laboratory testing methods is provided with a focus on collecting quality information for design purposes. A strong focus is given in developing an accurate assessment of pore water pressures, which, if not correctly understood can have disastrous consequences on tailings strength parameter interpretation and wall stability assessment in static and post-seismic conditions.The assessment of the contractive or dilative shearing behaviour of the tailings material and rigorous interpretation of design characteristic values are presented. Some comments on stability analysis options and proposed methodology are also provided.CITATION:Wentzinger, B and Armstrong, C, 2018. Lessons learnt in geotechnical investigation and stability analysis for upstream tailings storage facility raise design, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 333–348 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Buizen M

An investigation into the mechanics of sub-surface deformation caused by caving of the extracted area behind retreating longwall faces has been completed by the Subsidence Engineering Section of the New South Wales (NSW) Department of Minerals and Energy. Changes in strata bulk permeability were also measured by standard packer tests undertaken before and after mining. The strata movement was measured by a multi-wire borehole instrumentation system consisting of mechanical anchors installed at different horizons in a borehole extending from the surface to the coal seam. The mechanical anchors were collected to suspended weights on the surface by stainless steel multi-strand wires. The movement of these weights was monitored as the longwall face approached and retreated past the borehole. The anchors did not move significantly until the face went past the borehole. For subcritical extraction geometry with the extraction width to mining depth ratio of 124, the caving zone extended to roughly 9 times the extracted seam thickness above the seam roof. Tensile strains within the overburden tended to be much more closely related to stratigraphy than to the proximity to the extracted seam roof. Larger tensile strains were associated with layers of sandstone, siltstone and conglomerate, whereas layers of mudstones, claystones and coal underwent much smaller strains indicating subsidence in blocks. A beller correlation was observed between pre-mining Rock Quality Designation and permeability than between rock type and permeability. This correlation was less evident in the post-mining core logs. There was an overall increase in bulk permeability after mining.

Jan 1, 1990

By D Chalmers

"There is a tendency to treat mine roadways with fan installations as leak proof systems. Morecomplex ventilation arrangements are being installed in coal mines out of necessity or designand these can introduce additional hazards. This paper explores the leakage paths that can existaround fans and in particular the hazards these leakage paths may generate around undergroundfan installations. The behaviour or these leakage paths in the event of a fan failure has also beenexplored. Early detection of spontaneous combustion is essential, so understanding the leakage behaviour around fans especially boosters or main fans installed underground will assist in sett ing up monitoring locations in the correct places. If this behaviour is not fully understood then monitoring may be placed incorrectly, or trends may not be picked up until it is too late."

Jun 1, 2012

By Baker G

Chromite was recorded among the rare minerals in the natural beach sand concentrates on the coast of Northern New South Wales by Whitworth(l) in 1931, and the commercial production of zircon and rutile from these beach sands has yielded concentrates of ilmenite with small amounts of chromium. The chromite is a detrimental impurity in the utilisation of the ilmenite, and the difficulties that attend the separation of the small amount of chromite from the ilmunite have raised suggestions from time to time that chromite occurs with ilmenite in composite grains. The absence of such composite grains and the nature of the chromite grains has been indicated by the following mineragraphic examination of magnetic concentrates containing chromite which were prepared by the C.S.I.R. Ore Dressing Laboratory, Melbourne University, from ilmenite concentrates from beach sands at Norrie's Head, County Rous, New South Wales and Stradbroke Island, Queensland.The magnetic concentrates from each locality are divided into five fractions, and the No. 1 concentrate is the most highly magnetic and the tailing the least magnetic. Chromium assays as determined by the Ore Dressing Laboratory are as follows:-

Jan 1, 1948

By M Boon, M Franklin

This paper outlines the journey of cultural maturation and management system development at the Mt Rawdon (MRO) gold mine from its acquisition by Evolution Mining Limited (Evolution) in late 2011 to 2016.Evolution embarked upon a series of projects that aimed to improve the operational consistency and implementation of change on-site, while leveraging off the existing strengths of the operation. This document describes the gaps that were identified, the processes used to close them, and the resulting cultural change and production outcomes, with a specific focus on how to optimise the culture at any mining operation.MRO had a history of four owners in less than three years when it became a key asset of Evolution. The site leadership team (SLT) decided to influence the culture at MRO by reviewing and upgrading the existing management processes.The first priority was to improve transparency and collaboration at the SLT level, followed by improving competency in project management. The next phase was to strengthen the internal communication using a deliberately designed network of meetings, communication screens and other initiatives. Once there was some traction, the focus moved toward increasing production volume and decreasing cost per unit by improving short-term planning and execution capability. Together with other initiatives, this resulted in improved collaboration between all functions, which in turn netted over 37 per cent mining production uplift.Following solid success, a process of prioritisation and alignment management was implemented. This supported the ‘Mine to Mill one operation’ ideal and allowed the SLT to decide month-by-month what actions were to be prioritised. These priorities incorporated production realities and longer term imperatives of the balanced business plan.Much of this work was completed during a period of declining gold prices and a relentlessly strong Australian dollar, making it difficult to justify spending money on improvement projects. This work proved critical for the operation’s long-term survival.CITATION:Boon, M and Franklin, M, 2016. Improving consistency of delivery at Mt Rawdon Operation, in Proceedings International Mine Management Conference, pp 305-320 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By N Kawashima, R St C Smart, A M. Robertson

This paper focuses on a case study at a base metal mine located in a tropical semi-arid area of Western Australia (WA). It is demonstrated that understanding the geochemical nature of the mine tailings forms an integral part of innovative management strategies developed throughout the life-of-mine (LOM) when planning for mine closure. The tailings are currently stored at an above-ground valley fill tailings storage facility (TSF) and one option for long-term management under consideration is leaving the tailings in situ at mine closure and covering using the concept of an enhanced æstore and releaseÆ cover system.Extensive geochemical and mineralogical studies have found that the geochemical behaviour of the tailings in the TSF is significantly more benign than initially predicted. The sulfide content of the tailings is primarily pyrrhotite, which can be acid-forming, acid-neutral or acid-consuming depending on a number of factors including redox conditions. Tailings pore water at depth is pH neutral with excess alkalinity, low concentrations of dissolved metals and elevated sulfate concentration.Recent geochemical tests on tailings samples indicate that a reduction in the acid potential and a corresponding increase in the neutralising potential of the tailings, through partial removal of pyrrhotite at the ore processing stage, has the potential to further reduce the long-term risk of potential impact to the environment from any TSF seepage. The current work program investigates whether partial removal of pyrrhotite is feasible and secondly, whether this approach is necessary to produce a significantly better outcome at mine closure.CITATION:Robertson, A M, Kawashima, N, Smart, R St C and Schumann, R, 2012. Understanding tailings geochemistry - Continuous learning and innovation when planning for mine closure, in Proceedings Life-of-Mine 2012 , pp 287-292 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By M Spagnolo, M Ashley, D, L Reemeyer

PasmincoÆs Century Concentrator in North West Queensland commenced operations in November 1999. The nameplate production capacity of 500 000 tpa of zinc metal production in concentrate was achieved in August 2002. Completion of the production ramp up was successful due to the culmination of a number of initiatives throughout 2001 and 2002. Mine to mill interaction to understand and eliminate head grade related bottlenecks affecting Concentrator production and reduce feed variation. Grinding circuit process development û operating and process control strategies to improve stability and reduce grind size to support zinc recovery. Pumping upgrades to control spillage in ultrafine zinc flotation Low density zinc flotation strategy û to improve silica-sphalerite separation to improve zinc recovery while maintaining acceptable silica in final concentrate. Flotation circuit process development û froth crowders, froth cameras and reagent control strategies to improve primary zinc flotation performance. Review and implementation of longer campaigns between planned shutdowns to improve availability. Team reorganisation û to improve setting and implementation of metallurgical strategies. This paper describes these initiatives and their contribution in achieving the production target. It also notes the ball mill motor failures that delayed the successful achievement of the ramp up, and CenturyÆs response to minimise the production impact. The paper also outlines the capital improvement program that was implemented to improve zinc recovery to design 82.5 per cent recovery once the production rate had been achieved.

Jan 1, 2003

The Bellambi Coal Company Limited com menced longwall mining at South Bulli Colliery in 1965. At present it operates three long- wall units in two seams. Although results to date have been less successful than planned, it is apparent that this type of mining has tremendous potential in the particular conditions at South Bulli. Massive sandstone strata above the Bulli seam is the controlling influence on face conditions. The earliest equipment proved to be inadequate and the Company has progress- ively replaced and upgraded the roof supports and ancillary equipment so that the present units are capable of producing high and consistent outputs.

Jan 1, 1976

By L Vimercati, R Williams

Transitioning to a green future requires the mining industry to adopt sustainable practices. Filtered tailings are become a key expectation of the communities we operate in and are growing in a number or mining commodities including bauxite, nickel, gold and iron ore. The filtration technologies required range from dewatering screens to vacuum and pressure filters. Particular challenges faced in iron ore applications include large scale which means several units of large size are often required. In addition, a high specific gravity that cause sedimentation issues and a high abrasion level make demands on achieving reliability level at above 90 per cent. This paper describes the testing, selection criteria and specific features required to provide a rational option for equipment and plant design. An example of how this has been applied in an iron ore application in Brazil is used to demonstrate a successful outcome. This project installed four overhead beam filter presses each producing around 200 t/hr utilising a recessed chamber plate, feed pressures up to 15 bar, cake thickness of 5 mm. The moisture lower than 20 per cent that was produced was considered to provide material with handling and geotechnical properties to guarantee a safe stacking. Regular high pressure washing at 100 bar was considered imperative to maintain cloth life and process performance. The correct management of the system (OPEX control) by PLC control ensures a balance between machine potentials and plant needs. With this equilibrium it is possible to limit mechanical wear preserving equipment lifetime.

Sep 18, 2023

By W A. Peck

Raise boring is the preferred option for constructing ventilation shafts in Australia. The trend has been towards larger diameters and longer single-pass shafts, and if at all possible, reaming through to the surface. The risk of raise failures, due to missed, unforseen or latent ground conditions has therefore been increasing, along with the need for better, more confident stability assessments.While the stability of specific weak zones and structures must be assessed individually, empirical rock mass classification schemes have been successfully used for about the last 20 years to assess general raise stability; eg the McCracken and Stacey method (M&S).Unfortunately M&S, as originally documented in McCracken and Stacey (1989), did not include a database of raise diameter and rock mass conditions versus actual performance. Nor was there a procedure for assessing the risk of failure due to adverse ground conditions. Peck and Lee (2008) published an Australian database of raise bore performance. Raise diameter and ground conditions, in terms of a lower bound Qr value, were presented for 50 cases versus raise performance. This paper updates the 2008 raise performance plot with more and SRF-corrected data. McCracken and Stacey (1989) had previously recommended that additional geotechnical data should be acquired and analysed when the proposed raise plotted on the unstable side of raisebore stability ratio (RSR) = 1.3, but the Australian data used in this study also suggests that all sites with Qr Contributions and sensitivities of various rock mass parameters (RQD, Jn, Ja, Jr, Jw, SRF, time-dependent weathering/deterioration) to raise stability and risk of failure are discussed. Numerous case studies are used to illustrate issues with stability assessments.As raises can now be remotely supported using sprayed fibrecrete, questions of time-dependency are also discussed. In recent times, contiguous piles, ‘mini-piles’ and grouting have also been successfully used to presupport or otherwise improve the stability of near-surface sections of weathered, or poor quality rock masses.

Mar 21, 2011

Continuous, steady-state laboratory flotation tests showed that the recovery of cha1copyrite from a naturally occurring ore, under conditions closely resembling those of plant practice, could be expressed in terms of a first order rate equation.Tests on full-scale plant flotation cells, using impulse tracers, indicated ideal mixing of the pulp in the cells.It was demonstrated that values of first order flotation rate constants can onlv be obtained from conventional methods of analysis in special cases.Analysis of a plant sampling campaign by the author supported a first order kinetic equation for two mineral species, and for the individual size fractions of one of these.The effect of stage-addition of reagents is interpreted in kinetic terms.

Jan 1, 1966