Search Documents

By Roberts T, Firth B. A

A series of flotation experiments was carried out to study the interaction between the parameters of pulp density (mass per cent of solids in feed slurry) and frother addition (on the basis of solid mass feed rate). It was found that certain combinations of pulp density and frother additions caused large losses in yield. The interactive effect of these parameters can be primarily attributed to the total amount of frother added per unit of water. Consequently it is suggested that frother additions be made on the basis of water flow rate. As frother addition increased, in terms of the amount of frother per unit of water, yield increased rapidly but above an addition rate of about 10 g/tone it reached a plateau. Such results correlated well with qualitative visual observations of changes in bubble size and dispersion, with increasing levels of frother addition.

Jan 1, 1984

By A Ross, B De Rivaz

The results of full-scale tests on precast segment made at University of Roma are presented. The segments were cast using fibre-reinforced concrete produced without any traditional reinforcement, by using fiber made in high-strength steel and a new type of anchorage.Bending tests were performed in order to check the bearing capacity of the segments under the flexural actions; these occur during de-moulding, handling, storage phases as well as in the in situ condition (due to asymmetric soil pressure). Furthermore, point load tests simulating the TBM thrust were performed, in order to study the construction phase (excavation).The results show that the segment response largely respects the material testing and design advice according to the Fib Model Code 2010. Providing engineers, precast operators and builders confidence in material strengths and design methodology.CITATION:De Rivaz, B and Ross, A, 2014. Full-scale tests on precast tunnel segments made in concrete reinforced with high-strength steel fibres, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 469–476 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By J Seppelt

The Kanmantoo Copper Project is owned and operated by Hillgrove Resources Limited and is situated in the Adelaide Hills region in South Australia. Mining in the area has taken place off and on over the last 140 years to recover metal from both copper and lead-zinc ores. This paper focuses on the commissioning, ramp up and future outlook for the copper concentrator at the Kanmantoo Copper Project with major focus on issues encountered and operating performance achieved to date.CITATION:Seppelt, J, 2012. Commissioning of the Kanmantoo Copper Concentrator, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 127-136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By D A. Bowman, S Schafrik

With the goal of reducing injuries and fatalities related to haul truck accidents, this research investigates technologies and intervention strategies for improving worker training using a virtual environment (VE). Funded by the National Institute for Occupational Safety and Health (NIOSH), this research specifically focuses on training workers in preshift inspections of haul trucks to avoid preventable defects from causing worker injuries and expensive equipment damage. Improved training in these inspections is expected to increase uptime. The VE developed to train workers for preshift inspections consists of three phases: the virtual tour, the virtual inspection and the shift simulation. The virtual tour introduces information necessary to conduct a preshift inspection by guiding the worker around a haul truck, identifying parts to be inspected and explaining defects to look for. The virtual inspection assesses retention as the worker navigates around a haul truck and identifies defects. During the shift simulation, the worker is shown a simulation of the work shift, which animates severe consequences of any overlooked defects to emphasise the importance of preshift inspections. To provide multiple training platforms, desktop and CAVEÖ versions of the training VE were created. Flux Studio was used to model the environment and to produce Virtual Reality Modelling Language (VRML) files for the desktop version. DIVERSE, an application programming interface, was then used to implement a more realistic version of the VE in a CAVEÖ, a room-sized visualisation system. Initial feedback from mining colleagues indicates that the training VE may replace normal classroom training for preshift inspections in the future. As opposed to PowerPoint presentations and instructional videos, the training VE provides better spatial understanding of the location of parts and incorporates interactive features to actively engage drivers in the learning process, which may result in better retention. Initial feedback also indicates that minor improvements can be made to the virtual tour and virtual inspection phases.

Jan 1, 2008

By Grant BPM

The lower levels at the CSA Mine have been developed to mine reserves between theNo.7 level and No.9 level.Work on major excavations for the project began during 1982 with the develop-ment of the crusher chamber, on No.9 level. The brows and walls were pre-dowelled to improve stability before mining by mass blasting techniques.At the same time work commenced on theextension of No.2 Shaft from No.7 level toNo.11 level. The shaft was stripped, using hand held drilling, to a raise bored holeand concrete lined to a diameter of 5.5 metres. Plats were developed at No.8 level, No.9level and the loading station.

Jan 1, 1985

By G Corbett

Epithermal Au-Ag deposits form in the upper 1 km of the crust and are therefore best preserved in the less eroded Pacific rim arcs, although also recognised elsewhere. Two profoundly different ore fluid types give rise to low and high-sulfidation styles apparent as variations in ore and gangue mineralogy as well as characteristic zoned wall rock alteration. Low sulfidation epithermal Au deposits are derived from near neutral composite magmatic-meteoric fluids and divided into a group with a stronger intrusion association within arcs grading in time and space from: quartz-sulfide Au + Cu, to carbonate-base metal Au, and the epithermal quartz Au + Ag, whereas in strongly extensional settings the influx of meteoric waters promotes the development of chalcedony-ginguro banded Au-Ag epithermal veins. In the presence of continental crust particularly in Latin America polymetallic Ag-Au veins represent a Ag-rich equivalent of carbonate-base metal Au and passes upwards to chalcedony-ginguro Au-Ag style. By contrast high-sulfidation epithermal deposits are deposited from an acidic magmatic fluid which provided characteristic hydrothermal alteration by reaction with wall rocks grading outwards as mineral assemblages dominated by: vughy silica, alunite, pyrophyllite-diaspore, dickite-kaolin and then illite-smectite neutral clays. Au mineralisation is commonly refractory with enargite deposited dominantly later within the silica zone.Exploration for epithermal Au deposits benefits from an understanding of the controls to mineralisation which commonly give rise to the development of ore shoots with widest and highest Au grade ore zones. In low-sulfidation systems a combination of competent host rocks, dilatant structures, higher grade styles of mineralisation and efficient mechanism of Au deposition, contribute towards ore shoot formation. High-sulfidation epithermal Au systems occur in permeable volcanic and breccia host rocks which are linked by major structures to the magmatic source.CITATION:Corbett, G, 2013. Pacific Rim epithermal Au-Ag, in Proceedings World Gold 2013 , pp 5-14 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By M Erskine, R Mills

This paper approaches tailings dam risk management from the perspective of how other high hazard industries approach the management of their catastrophic event risks, with the aim to provide recommendations from these learnings for the industry to adopt.

Jul 1, 2021

By V Mutton, L Potts, D Joyce

This paper describes the method of extracting sill pillars within the underground operation from under unconsolidated mullock fill at the Cracow Gold Mine. This pillar recovery method was initially successfully used to recover sill pillars at Crusader Mine, Western Australia in 2001. Globally significant resources have been sterilised due to the placement of loose rock fill above crown pillars and within adjacent stopes. The method described here offers significant opportunities to increase recovery of sill pillar recoveries.The royal orebody sill pillars at Cracow Gold Mine form a significant resource. Extraction of these pillars needed to be undertaken with minimal ore dilution and maximum ore recovery. The application that was selected to consolidate the loose mullock fill above each pillar used an injection grouting process (Minova FB200).Cracow Gold Mine mining method is bottom up bench mining. The pillars were left within the orebody to allow for stoping to commence whilst the decline was being developed. Due to the remainder of the orebody being extracted the only access to consolidate the backfill was from the sill pillar extraction level. Numerous problems were encountered and overcome from product selection and trial, system of injection to extraction.This pillar recovery process achieved a 95 per cent recovery of the sill pillar compared with an estimated 60 per cent typical for other mining options.CITATION:Potts, L, Mutton, V and Joyce, D, 2012. Pillar recovery at Cracow gold mine using grouted consolidated mullock, in Proceedings Narrow Vein Mining 2012 , pp 179-184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By G Harbort, D Clarke, D Morgan, C Sola

Northparkes Mines commenced production in 1994 and the mine has significant reserves to allow operation into the future. There are a number of potential future concentrator feed sources with variable sulfide mineralogy and grades.In February 2012 a comprehensive flotation survey was conducted to allow mass balancing and evaluate the operation of the flotation circuit. A rudimentary, copper element only, unsized flotation simulator was developed to evaluate high level potential for optimisation and improvement. In 2013 this flotation model was expanded to produce a mineral based, floatability component model to estimate the effect of future concentrator feed source on metallurgical performance. This revised model allows various circuit configurations to be simulated to provide a high level blueprint for the long-term planning to maximise performance.This paper provides a review of the process followed to develop the model, including an analysis into the mineral floatability component model and its calibration against plant operations. The effect of varying feed mineralogy and feed quality on future performance has allowed an internal review of potential circuit changes needed to accommodate the changing future feed.CITATION:Clarke, D, Harbort, G, Morgan, D and Sola, C, 2014. Northparkes Mines – flotation and planning for the future, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 203–208 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Bodnaras G. E, Sceresini P. A

The Filblast Cyanidation Process incorporates the advantages of intense high shear mixing, high dissolved oxygen concentration and high pressure to achieve extremely rapid gold dissolution rates. This is made possible by the unique design of the Filblast gas shear reactor. The reactor is a rugged and compact in-line device. The outer casing is protected by a polyurethane coating and the internal parts are of wear resistant polymer. The largest unit built to-date has overall dimensions of 1200 mm length by 300 mm diameter and has a capacity of 150 dry tonnes per hour at 40 - 45 per cent solids. Service life at this throughput is at least three months. The process may further be applied to high temperature leaching of refractory gold ores or other metals. Wear resistant metal or ceramic materials would be employed for this duty. Four mines are currently employing the Filblast Process for treating a variety of ore types ranging from highly reactive, almost impossible to treat, pyrrhotite/arsenopyrite to deeply weathered clay ore which forms a highly viscous pulp. The effect of shear thinning has resulted in improved adsorption kinetics resulting in higher carbon loading and reduced soluble gold loss. Total tonnage treated is approximately four million. Operating costs which include leasing and maintenance charges for the Filblast and pump power costs are about 16 cents per tonne. This is equivalent to about ten per cent of savings. Laboratory scale units having capacities up to 30 litres/min are available for test work but laboratory testing techniques so far developed do not accurately reflect the oxygen and cyanide savings which have been achieved in the plant.

Jan 1, 1994

By A J. Moore

Blasting operations in open cut mines results in airblast, ground vibration and rock movement with the potential for wild flyrock. In some mines there is a trend towards blasting closer to established infrastructure as extraction boundaries alter with increased resource prices and changed economic circumstances. Mine infrastructure in close proximity to blasting has the potential to be damaged by ground vibration and wild flyrock especially. To provide guidance for the determination of appropriate buffer distances and blast specifications, this paper describes methodologies that may be used to determine the potential for damage to infrastructure by predicting:dynamic blast;near field ground vibration levels;dynamic blast strains induced in infrastructure by consideration of ground vibration,ground strain and response amplification;potential for damage by comparing induced strains with allowable working strainsfrom structure design codes and serviceability requirements; andflyrock throw distances based on models developed from flyrock investigations.This report demonstrates the use of strain prediction methodologies developed during Australian Coal Association Research Programme (ACARP) Project C14057 for infrastructure such as conveyor belts, transmission poles and towers, buildings and bridges.

Nov 8, 2011

By T Angerer, N H. Maund, S Hagemann, D R. Cowan

Cliffs Natural Resources Pty Ltd - Asia Pacific Iron Ore's (formerly Portman Iron Ore Limited) K deposit (Dowd's Hill), at its Koolyanobbing operation in Western Australia, hosts enriched magnetite mineralisation below the presently mined haematite-goethite ore zone. Two distinct northwest-southeast elongated, highly magnetic anomalous bodies that dip to the north-east appear to be sourced by this deeper mineralisation. Magnetic modelling indicates significant remanent magnetisation with Qratios around 1.5, directed shallow down. The north-west anomaly is overlain by a ridge of uneconomic banded iron formation (BIF) and the present waste dump, whereas the south-east body was partly exposed during ongoing mining of overlying haematite-goethite ore. Sections of the magnetite mineralisation in this south-east anomaly were intersected previously by diamond drill holes. Review of the historic cores identified potential magnetite enrichment, with grades and mineralogy that might be amenable to beneficiation. A first-phase reverse circulation drilling program was designed to further delineate the trend and extent of the two anomalies. The following magnetite mineralisation assemblages are recognised from cores, reverse circulation (RC) drill cuttings and pit mapping of the south-east magnetic body: higher-grade magnetite-haematite ¦ goethite and magnetite ¦ pyrite and lower-grade, recrystallised magnetite-quartz (BIF), magnetite-carbonate, magnetite-talc and minor magnetite-bearing mafic schist. Disseminated specularite is locally present in theassemblages. Talc-schist and massive pyrite occur along the footwall contact. Magnetic susceptibility measured from drill chips within the magnetite-enriched zones reveals an apparent susceptibility values range of 0.2 to 1.3 SI. Preliminary results from Satmagan and Davis tube recovery analysis shows that the magnetite content in these mineralised zones correlate well with existing geophysical data and magnetic susceptibility measurements.

Jan 1, 2009

By A K. Raina, V M. S R Murthy

Rock mass response in blasting is an important element to determine the performance of a blast along with its other outcomes. The near-field monitoring for rock mass response analysis is vital for determining the behaviour of a blast; however, due to costly and cumbersome methods involved in such measurements the subject has received scant attention so far and the publications on this account are perfunctory in nature. This paper presents a non-destructive method to monitor the blast-induced pressure in the rock mass at a distance from a blasthole. The methodology of monitoring and a few examples of actual field monitoring are detailed in this paper. The responses of the rock in the near-field of a blasthole under dynamic loading have been documented to predict fragmentation and throw. The proposed method has also been used in limited cases earlier by the author to predict flyrock using a semi-empirical method and trajectory equation. The pros and cons of the method are discussed while throwing light on the actual response and the prediction of fragmentation and throw of blasted rock.CITATION:Raina, A K and Murthy, V M S R, 2015. Measurement of blast-induced pressure in bench blasting and deciphering explosive performance through rock mass response analysis – a methodology, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 501–508 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By M J. Newton

As part of the AMIRA P843 project Keeney and Walters (2008) describe how the principal components analysis (PCA) method can be used to identify classes of samples with similar metallurgical characteristics. However PCA does not take account of the location of each sample in 3D space. This paper describes a study to analyse the spatial distributions of the classes and determine appropriate modelling methods to control the estimation of the comminution parameters and mill performance indices into a 3D block model. This includes but is not restricted to geostatistical techniques that are used for grade modelling. The starting point for the study is the class definitions and the regression models for estimating the comminution parameters and performance indices. Each sample is assigned a class and the spatial distribution of each class has been analysed using different techniques including the calculation of variograms. This establishes whether the classes can be used as domain control for estimation into the block model – a procedure similar to using geological rock type domains for controlling the estimation of grades for a resource model. However, standard geostatistical estimation methods such as ordinary kriging assume that the variable being estimated is additive or linear. This assumption is valid for variables such as grade but this is not necessarily the case for the comminution parameters or the performance indices. Therefore the estimation procedure must either use variables that are definitely additive or the effect of potential non-additivity must be tested and accounted for where possible.The results of the study show how performance indices such as recovery, throughput and specific power can be estimated into the block model. This model is then combined with the geological model to provide a multi-parametric model that is used to optimise the mine planning and scheduling activities which can lead to significant improvements in NPV.

Sep 5, 2011

By E M. Jones

On 26 June 2000 a hydraulic fill retaining barricade failed at the Bronzewing mine in Western Australia. The barricade failure resulted in the release of 19 000 m3 of saturated hydraulic fill into the mine, which caused the deaths of three miners. Following this tragic accident, the practices and procedures of mines using hydraulic fills came under intense scrutiny by regulatory bodies and mining companies. At this time, the use of hydraulic fill at NormandyÆs zinc/copper Scuddles mine was suspended and waste rock became the sole backfill material in use underground. By 2003, development of the mine adjacent to Scuddles, Gossan Hill had progressed to a point where a self-supporting fill material was required to enable full recovery of high-grade ore. Cemented hydraulic fill (CHF) was identified as the optimal fill type and work began on designing appropriate management procedures and controls to ensure the safe implementation. This work included definition of the fill properties, plant design and construction, reticulation system design, design of stope barricades and drainage systems and fill placement control and monitoring practices. CHF placement began on 16 July 2004 and has continued to date. Significant operational experience has since been gained in areas including plant performance, fill product quality assurance, barricade construction, stope drainage and in situ performance.

Jan 1, 2008

By D Timms

The Kempfield deposit is located in the Hill End Trough, one of several intracratonic basins developed during Silurian–Devonian time, in the eastern province of the Lachlan Orogen, Eastern Australia.The deposit contains an oxide resource of 5.8 Mt @ 58 g/t Ag and a sulfide resource of 14.4 Mt @ 45 g/t Ag, 1.7 per cent Zn and 0.6 per cent Pb, classified and reported in compliance with the JORC Code. The deposit has been previously explored by a number of companies, including INCO, Shell, Jones Mining, Golden Cross Resources and recently Argent Minerals Ltd (Argent). Argent is currently completing a definitive feasibility study with a view to mining the deposit.The deposit is hosted at the boundary between the Molong High to the west, comprising Ordovician sediments and volcanic rocks and the Hill End Trough to the east, interpreted as a back-arc basin containing Silurian sediments and siliceous-feldspathic volcanic rocks. The boundary between these two strato tectonic units is an imbricate thrust fault zone known as the Copperhannia Thrust.The Kempfield deposit is hosted in felsic volcanic rocks known as the Kangaloolah Volcanics. These have been in-faulted and folded into the Middle Ordovician meta-sediments of the Coombing Formation of metasediments along the Copperhannia Thrust. The Kangaloolah Volcanics belong to the Late Silurian Mumbil Group, comprising submarine carbonate-shale facies interspersed with extensive felsic volcanic piles, which grade conformably upwards into turbiditic sandstone and siltstone sequences (interpreted to represent a deeper depositional environment). These turbiditic rocks are known as the Campbells Formation, comprising siltstone, sandstone and andesitic tuff. The rocks at Kempfield are metamorphosed to lower greenschist facies, reflected through the different type of schists.Silver, gold, lead, zinc mineralisation is hosted in barite-rich horizons, near the boundary to quartz-phyric tuffaceous rocks in submarine, immature, reworked felsic ash tuffs. Barite appears to be hosted in greatest concentrations by the coarser grained volcanoclastic sandstones and grits, whilst intercalated siltstones are volumetrically minor and tend to return low barite and silver. Mineralisation is hosted in stratiform and probably stratabound barite-rich horizons. A northeast-trending, steeply dipping, metamorphic cleavage (S1) occurs throughout the project area.

Aug 22, 2011

By P Kirsch, P Jagals, D Viswanathan, J Shandro, R LaBouchardiere

The planning, design and operation of mines must include the development of positive environmental, community and land-use benefits if it is to achieve good corporate social responsibility and minimise detrimental impacts throughout the life of the mine. Life-of-mine (LOM) planning should, therefore, consider conducting mining activities in the best socially, environmentally and economically acceptable manner, from the commencement of exploration to post-closure of the mine. Current knowledge of LOM activities in relation to public health (life-of-community, or LOC) impacts neither fully captures the full suite of human health and well-being impacts, nor comprehensively informs society on these issues. This knowledge gap is becoming more apparent as public antipathy is increasing towards mining activities within Australia, Canada and globally. The purpose of this paper is to present preliminary and informative results of a literature review to gain insight into the extent of available public health and well-being knowledge associated with mining development. LOM development must also benefit the LOC, in that it must aim to minimise detrimental impacts, and maximise beneficial (including health) impacts on all associated communities. Health planning and programing for mitigation of potential adverse health impacts of mining should extend beyond the scope of work-related injury and illness (resulting from chronic exposure to harmful substances, infectious and lifestyle illnesses), to the health and well-being of workersÆ families and extended associated communities. By mapping the available but rather scarce literature on LOC areas to recognised LOM stages, this review found shortcomings and imbalances regarding research reporting on mining and its health-related impacts in the worker-to-community continuum.CITATION:Kirsch, P, Viswanathan, D, LaBouchardiere, R, Shandro, J and Jagals, P, 2012. Health impacts extend from the life of a mine to the life of a community - Knowledge gaps, in Proceedings Life-of-Mine 2012 , pp 161-168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Doig ID, Phillips HR

As a prelude to studying the sorption desorption and permeability behaviour of coal cores in a triaxial stressing rig using sorb- able gases, the air permeability of typical cores was measured. Lump coal samples were obtained from three gas-troubled collieries in Queensland and New South Wales. These were cored in the laboratory and a simple laboratory permeameter employed which accepted 38 x 40 mm cores in a thick rubber sheath. Air pressure of 500 kPa was applied outside the sheath to provide suitable sealing between the rubber and the coal. Differential driving pressures up to 100 kPa were employed and the air flow measured by displacement of water columns in inverted graduated cylinders. Flow measurements accurate to + 2% could thereby be achieved. Coal lumps were cored both parallel and perpen- dicular to the bedding plane, and were observed prior to measurement for any notable features, in particular for the presence of fissures. Between samples an overall variation of from 100 milliDarcy was found in Appin, Westcliff and Leichhardt coals. Significant variation was observed both from section to section of a core and between regions of a

Jan 1, 1982

By D Liu, M Edraki, L Berry

The presence of clay minerals slows down the settling rate and mitigates compact consolidation efficiency in tailings dewatering. The increasing use of saline water in many plants, affects the dewatering performance and presents the mining industry with new concerns. Efficient tailings dewatering is a great challenge due to the complexity character of tailings, especially clay mineralogy, clay content, and water chemistry. In this study, existing studies of the effect of different affecting parameters, such as pH, ionic strength and polymer flocculants, on clay aggregation behaviours are reviewed. The settling behaviours of three types of commonly observed clay minerals in tailings, kaolinite, bentonite, and illite, are also investigated in saline water with different water salinity as a case study. The settling rates of clay minerals are found to be affected by water salinity, clay type, clay content and polymer dosage levels. High salinity water hinders the settling of kaolinite but assists the settling of bentonite and illite through formation of different aggregation structures.The current work has indicated that strategies to promote more rapid dewatering could include adjusting flocculant type or level, water salinity and salt balance, and tailings solid content levels. Implementing dewatering strategies may require a more detailed knowledge of the effect of surface chemistry on the nature and strength of the clay inter-particle forces. This study discusses the research gaps on how to better manage clay-rich tailings in saline water and identifies new research directions. The development of a water management model, supported through in-line monitoring data to predict and manipulate of the surface chemistry of the clay component of the tailings could be a new direction to manage the issues associated with clay minerals in the process of dewatering and tailings management. Mine planning (water use requirements, operating costs) could benefit from more detailed studies on dewatering of clay-rich tailings in saline water. CITATION:Liu, D, Edraki, M and Berry, L, 2018. Improving the dewatering efficiency of clay-rich tailings in saline water, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 476–484 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By R Schmitt, Y Ghorbani, I McElroy, N J. Bolin, M Parian

Aitik is a large copper porphyry type deposit located in northern Sweden, currently exploited at an annual rate of approximately 45 Mt. The ore’s exceptionally low head grade of 0.25 per cent Cu and varying degrees of hardness across the entire deposit pose challenges to the two fully autogenous grinding lines, each of which comprises a primary autogenous mill in series with a pebble mill. The variability in ore grindability frequently leads to fluctuations in mill throughput. Within the framework of a geometallurgical approach, the present study investigated the relationships between ore grindability and modal mineralogy. For this purpose, drill core samples from different lithologies were subjected to Boliden AB’s in-house grindability tests. This fully autogenous laboratory-scale test generates a grindability index mainly related to abrasion breakage, which is a significant breakage mechanism within autogenous mills. The test results suggested divergent degrees of grindability within and across the selected rock types. A combination of scanning electron microscopy, X-ray powder diffraction, and X-ray fluorescence analyses was performed for the grinding products and bulk mineral samples. The resulting mineralogical and elemental properties were subsequently correlated to the parameters from the grindability tests. It was shown that the main mineral phases, such as plagioclase, quartz, and micas, correlate well with the grindability indices. Similar correlations were found regarding the sample’s chemical composition, attributable to the main mineral phases. A further inverse correlation was established between the sample’s calculated average Mohs hardness and the grindability indices. Moreover, mineral liberation information provided by scanning electron microscopy was associated with the parameters mentioned earlier. The identified relationships between grindability, modal mineralogy, and element grades may help Boliden develop a predictive throughput model for Aitik based on the mine’s block model.

Aug 24, 2022