Search Documents

By J. E. Ryan

TRONA, Calif., is a miniature urban community of some 3500 people, located on the northwest shore of dry Searles Lake in the extreme northwest corner of San Bernardino County, approximately 186 miles north and east of Los Angeles. Since it is situated on the Mojave Desert, a typically desert climate prevails with wide variations in temperature between day and night, extreme daytime summer heat, and cool to cold winters. Rainfall averages somewhat less than 4 in. per year, and dust storms are common. The rate of evaporation, however, is great, amounting to 6 to 9 ft of water per year. The extremely low humidity makes the summer heat of 110°F tolerable with only a mild, temporary discomfort.

Jan 5, 1951

By W. L. Staker

The Bureau of Mines investigated selective extraction of Au and Ag from a low-grade Au ore containing Hg. Gold and silver were extracted from the ore in cyanide slurries, and Hg extraction was suppressed with sodium or calcium sulfide. Maximum Au extraction and minimum Hg extraction were obtained using solutions containing 0.34 lb NaCN/ton of solution. Increasing the cyanide concentration increased Hg extraction without increasing Au extraction. Mercury extraction from the ore was suppressed with 0.5 to 2.9 lb CaS/lb Hg in the ore. Gold-to-mercury ratios of 100:l to 400:l were obtained in the leach solution, and on the activated carbon in a CIP circuit.

Jan 1, 1984

By S. Tiwary, S. Samanta, B. N. Pandey, N. C. Saxena, R. Sinha, B. P. Nandy, B. Singh

Subsidence investigations over one bord and pillar and one longwall caved panel at Dhemomain colliery showed that, although the width-depth ratio (0.82 and 0.83) and working and strata conditions were almost identical, the maximum subsidence over bord and pillar panel was 46.2 per cent of extraction thickness against only 6.9 per cent over longwall panel. The angle of draw was 13O to 210 and 66 to 95 per cent of the subsidence had taken place immediately after extraction. The subsidence profiles were not symmetrical and were of funnel like shape. There was wide variation in subsidence movements over caved faces in India mainly due to difference in the composition of supercumbent strata.

Jan 1, 1983

By Fred N. Kissell, Natesa I. Jayaraman

Introduction This paper describes a recent Bureau of Mines research project that resulted in a simple procedure for reducing the dust exposure of longwall shearer operators. This project involved the development and testing of a water spray and passive shield system to hold dust against the face and away from the shearer operators. This system is known as the Shearer- Clearer.

Jan 1, 1981

By Mark C. Malamphy

MAJOR JUAREZ TAVORA, who recently accepted the post of Minister of Agriculture in Brazil, has reorganized his department. Not least among those sub: divisions of the "Ministerio" which underwent radical changes in the general reform was the Serviqo Geologico e Mineralogico do Brasil. This well- known organization was declared extinct, and in its place was created a new cleparttnent ' termed "Departamento Nacional cle Producqao Mineral," which immediately took over all the work of the olcl Servico Geologico ill addition to certain new duties. Dr. .. Domingos Fleury- da Rocha, former head of the School of Mines of Ouro Preto, was called to Xio to assume the newly created post of Director General of the department of Mineral Production. His department will have live divisions :

Jan 1, 1934

By Frederick Bacorn

THE paper of Reno H.. Sales on Ore Deposits at Butte, Mont.,' is a careful and painstaking work, an important contribution to the literature of the subject. As is almost inevitable in a work of such magnitude, a few misstatements occur; and some of these I shall endeavor to point out. Mr. Sales has also fallen into error, as I think, in the application of his theory of ore deposition; and while the modification which I venture to suggest is a minor one geologically, it is of great economic importance. I refer to Mr. Sales's idea of an outward migration of mineralizing solutions from a supposed central copper zone. In order that I may make myself plain, I must first epitomize the theory as a whole, which I understand to be this: All of the Butte ore deposits (save those along the Continental fault, not herein considered) are derived from solutions of magmatic origin, which, at the beginning of their ascent from a great depth, were, acid in reaction, hot, and were carriers of copper, zinc, manganese and other metals. As they departed from their point of origin they lost heat, and, because of reactions with the wall rock, became more and more alkaline. The metal deposited from these solutions in their hot condition was principally copper; and, as they cooled, they deposited less and less copper and more and more manganese and zinc, until the copper practically disappeared. With this theory in general I have no fault to find, nor have I, it must be stated, the qualifications necessary to enable me to pass upon it critically; but it seems to me to be reasonable and probable, and is one which I am quite willing to accept.

Jan 8, 1914

By Y. C. Liu, H. Margolin

Investigation of martensite habit plane in water-quenched Ti-Mn alloys was carried out in the range of manganese contents between 4.35 and 5.25 pct. On the basis of 22 measurements, the poles were observed to fall into two groups, indicating the existence of two habit planes. The Miller indices of the poles close to these two groups were found to be <334>ß and <344>ß. TITANIUM has an allotropic transformation at 882.1° ± 0.5C1 by which the high temperature ß (body-centered cubic) phase changes to a (hexagonal close-packed) phase. It is well known, as in the case of low carbon steel, that the unalloyed high temperature ß phase cannot be retained no matter how rapid the cooling rate. However, the addition of alloying elements usually lowers the transformation temperature continuously and stabilizes the ß phase to a temperature much lower than the allotropic transformation temperature in pure titanium. A typical example of this behavior is found with manganese-alloying of titanium. Fig. 1 shows the titanium-rich Ti-Mn equilibrium diagram as established by Battelle Memorial Institute.&apos; The addition of manganese lowers the ß transus line and the eutectoid reaction takes place at 550°C, the eutectoid composition being 20 wt pct Mn. However, upon quenching to room temperature from the ß field, the ß phase can be completely retained with much less manganese, see Fig. 2. If the composition is less than that required to stabilize the ß phase completely, a plate-like structure, similar to that of martensite in other alloy systems, appears as shown in Fig. 3. Much lower alloying content merely intensifies the amounts of these transformed structures, as shown in Fig. 4. This paper presents the results of an investigation of the habit plane of these martensitic structures in Ti-Mn alloys. Experimental Procedure Investigation of the pole of a given platelet was made using the two-surface method of analysis." In order that a given martensite trace on two surfaces be readily recognized both at low and high magnifications, it is desirable that only a small amount of martensite be present. From a review of the data obtained at Battelle Memorial Institute4 on quench hardening in Ti-Mn alloys and the results of Duwez" on transformation in Ti-MO alloys, it was decided that the most appropriate Ti-Mn composition for this study would be about 6 pct Mn. A group of alloys containing from 3 to 10 pct Mn was made to bracket this composition. The choice of the 6 pct alloy was apparently proper, since it was later learned that approximately 5.5 to 6 pct Mn is required to stabilize the ß phase on water quenching.

Jan 1, 1954

By G. R. Purdy, J. A. Malcolm

The isothermal dendritic precipitation of y in p CuZnSn is compared with the isothermal formation of Widmanstatten a plates in p CuZn. Although both precipitates are evidently bounded by semicoherent interfaces, the dendritic shape of y evolves through smooth "sinuoidal" shape perturbations, while a-p interfaces tend to be strictly planar, or rnicroscopically faceted. An estimate of the average inter-facial free energy of cube-oriented y in p through the Mullins-Sekerka analysis indicates that it is low (of the order of 50 ergs per sq cm). Interface mication is apparently controlled by volunle dij&apos;usion, and the observed anisotropy in growth probably results from anisotropy of inter facial free energy. Studies of the grain boundary precipitation of y in p indicate that the precipitate can grow in both $ grains, but becomes unstable with respect to the grain with which it shares a mobile semicoherent interface. Facets observed at the tips of Kurdjumov-Sacks-oriented Wid-manstatten a plates correspond to variants of an irrational hahit, near (231)0. Comparison with Hu and Smith&apos;s determination of relative interfacial free energies of a-(3 boundaries suggests that this system possesses an extremely deep o cup, which results in an ej&apos;ective low-o zone. The possible effects of such a cup on the stability of a-p interfaces are discussed, a needles, grown during rapid continuous cooling, possess microscopically smooth interfaces, and are characterized by a high degree of&apos; damage in the region of the boundaries. These boundaries, induced to move on tempering at 200"C, become faceted as equilibrium is approached, which seems to indicate that boundary structure and mobility in this system are dependent on the local degvee of departure from equilibrium MULLINS and sekerkal have elucidated the phase boundary stabilizing effect of surface tension. a factor not taken into account in previous treatments of morphological development. Their analysis applies to the isothermal growth of a pure spherical precipitate (planar in the limit of infinite radius) in a slightly supersaturated solution, under conditions of inter-facial local equilibrium and isotropy of interfacial free energy. More recently, several other factors which might tend to stabilize planar interfaces have received attention. These are: i) interface diffusion;4"8 and ii) slow interfacial reaction. cahn7 included a slight anisotropy in interfacial free energy, and showed that it has no stabilizing effect, but forces shape perturbations to reflect the anisotropy. shewmon4 noted that dendritic morphologies are rarely observed in solid-solid systems, and, in particular, postulated that slow interfacial reaction occurs at all boundaries between proeutectoid ferrite and austenite, except those which propagate parallel to {11 l)y planes (for Kurdjumov-Sachs [K-S] related phases). Previously, Aaronson~ had proposed interfacial reaction at the broad faces of Widmanstatten plates, and expected that the lateral motion of high-mobility incoherent ledge edges would produce planar precipitates bounded by law-mobility semi-coherent interfaces. The problem of interfacial reaction during the dif-fusional formation of precipitates has often been ignored, although it is apparent that a small component of chemical reaction must exist at any moving interface." Further, all solutions of the diffusion equations for boundary conditions corresponding to isothermal growth predict infinite growth rate at time zero, so that elements of interfacial reaction would be most easily detected at early times. However, reported deviations from diffusion control are comparatively rare," and the local-equilibrium diffusion-control model appears adequate for the description of many isothermal growth systems.&apos;2"9 Cahn14 has treated the problem of migration of an interface which is able to reach positional energy minima, and concluded that such an interface, if subjected to a high local ther-modynamic "driving force", may migrate normal to itself without the benefit of ledges. As local equi-

Jan 1, 1968

By D. Turnbull, J. H. Hollomon

THERE is a large body of evidence&apos;" indicating that solidification during the liquid-solid transition is usually induced by heterogeneities present in the liquid. By dispersing liquid metals into small droplets, the impurities responsible for catalyzing solidification are isolated within a small number of these droplets. The effect of the foreign body therefore is restricted to a single drop by this technique. Thus upon cooling below the melting temperature, solidification is initiated by homogeneous nucleation in the majority of the droplets that do not contain impurities. In the case of solidification of liquid metals, the activation energy for nucleation is so great that its rate changes by orders of magnitude for a change in temperature of only several degrees centigrade.&apos; Effectively homogeneous nucleation occurs at a critical temperature upon continuous cooling. Thus by microscopic observation of single particles during cooling, a temperature at which the rate of homogeneous nucleation becomes sensible can be determined.3 since at the temperatures at which nucleation occurs in the absence of impurities the rate of crystal growth is extremely rapid, the temperature at which the entire particle solidifies is very nearly the temperature at which the nucleation of the solidification occurs. Thus for liquids that freeze at high temperatures the onset of nucleation can be established by simply observing the temperature at which the marked heat evolution and increase in brightness of the particle occur. For liquids that freeze at lower temperatures the onset of nucleation can be determined by a rumpling and change in shape of the particle resulting from its solidification. The microscopic technique for observing the solidification of small particles has already been described." In earlier papers the nucleation of solidification of pure metals 5,6 and of alloy systems7 showing complete liquid and solid solubility have been described. In the present paper, the observations are extended to a simple eutectic system (Pb-Sn) where the possibility of the formation of two solid phases exists. Metals for the investigation were obtained from the American Smelting and Refining Co. in the form of pure lead and pure tin, 99.8 and 99.9 pct purity, respectively. An ingot of each of the pure metals was made into shot by heating the metals at a temperature about 50 °C in excess of the melting point and pouring the liquid slowly into a container of water at 15°C. Samples of the shotted pure metals were weighed out to make alloys containing 5, 10, 15, 20, 25, 30, 40, 50, 60, 70, 80, and 90 atomic pct Pb. Samples of each alloy were then melted in separate beakers. Each melt was poured through a pyrex funnel into a cylindrical mold (% in. ID). The casting solidified in 10 to 20 sec. The inside of the mold as well as the funnel through which the metal was poured were coated with graphite to eliminate adherence of the metal. Analyses were performed on some of the compositions and are given in Table I. The compositions also were checked for these samples and for those that were not analyzed by determining the spread between the liquidus and the solidus upon melting the small metal particles. These measurements agreed as well with the nominal compositions as the analyses listed above. Results The results of the supercooling experiments for the several alloys are summarized in Table II and plotted on the constitution diagram in Fig. 1. Data for the pure lead and pure tin were taken from earlier investigations. The values for the maximum supercooling of the several alloys are the average of several determinations on a number of drops of each alloy. The maximum value in any determination was within about 2 pct of the average. For the alloys containing from 20 to 60 atomic pct Sn, inclusive, two marked changes of the surface structure were observed upon cooling. At the higher temperature, after the first appearance of the solid phase it continued to grow slowly at a constant temperature and then stopped. At the lower temperature the alteration of surface structure was abrupt. For the alloys containing from 70 to 95 atomic pct Sn, inclusive, an abrupt change in surface structure was observed at a single critical temperature.

Jan 1, 1952

By J. Elmer Thomas

The evolution of the oil business is one of the great industrial romances of modern times. First used as a medicine, then as a lubricant, then as an illuminant, and finally as a motor fuel, each change in its principal usage caused large increases in consumption. Producing Successes The producing branch of the industry responded ably to the demands made upon it. Never was there a famine, rarely any threat of scarcity, and stored inventories were gradually accumulated to form comfortable working stocks. Originally an erratic and hazardous undertaking, the discovery and development of oil fields has made such strides as to classify now as a science. When storage stocks were low, production in close balance with consumption, and demand trending sharply upward, considerable concern was expressed over future needs. Price was very responsive to fluctuations in supply under those conditions, and quotations for crude and refined oils exhibited wide swings. A very different situation exists today. Consideration of the statistics only since the war will show how recent has been this change. In the 10-year period from 1918 to 1927 inclusive, we produced in the United States 6,100,000,000 bbl. of crude and imported 900,000,000 bbl., our total supply being 7,000,000,000 bbl. The consumption was 6,600,000,000 bbl., thus adding to stocks 400,000,000 bbl., an accumulation of somewhat less than 6 per cent. of the total supply. During that period virtually every field was promptly developed as soon as discovered and nearly every well in the country was producing at full capacity. With the maximum production of the wells required to take care of the rapid increases in consumption, with storage stocks moderate and proven reserves very slight, the producing division of the industry acquired a tempo not needed now. Potential Surplus Today the situation is vastly different. The economic consumption is about 2,700,000 bbl., with current production slightly in excess of that.

Jan 1, 1930

By D. C. Bard

THESE notes are based on the megascopic study of a suite of 2,400 specimens of minerals and ores from the Butte mines, combined with field observations at intervals over a period of several years. The estimate of average vein composition is based on field acquaintance with the veins. It is probably correct in its broader proportions, and should be of use for comparison. Chemical and Mineral Composition of Butte Sulphide Vein. Matter. Per Cent. Oxygen 43.00-Quartz, rhodonite, rhodochrosite, barite, calcite, and hübnerite. Silicon 36.00-Quartz, rhodonite, and willemite (very rare). Sulphur 5.00-Sulphides of. iron, zinc, copper, lead,. and sulphates of barium and rarely calcium. Iron 5.00-Ferric sulphides (pyrite, bornite, chalcopyrite), also in sphalerite, tetrahedrite, and rarely hematite and siderite. Manganese, . . . . 2.00-Rhodonite, rhodochrosite, and hübnerite. Zinc, . . . . 1.00-Spha erite, very rare wurtzite and willemite, and tetrahedrite and tennantite.

Jan 8, 1913

By W. J. Rogers, L. J. Dwiggins, R. O. Williams

THERE has been comparatively little work on the importance of strain rate and temperature as variables in the formation of deformation textures. For this reason the present work was started, the choice of compression being in part that of convenience and in part because of the absence of quantitative data in this area. These do not turn out to be important variables within the range studied which permits the results to be condensed into this note. Samples 1/4 in. in diam and 1/2 in. long were machined from 99.9 pct pure commercial aluminum and recrystallized to a fine grain size. A set of five samples were deformed between a spring-driven weight and an anvil resulting in roughly 20 pct strain each time. The strain rate varied because of decle-ration and shortening of the sample but would average about 10&apos; per min. Deformation at temperatures over the range of -76" to 150°C were obtained by heating or cooling the samples. Complete lubrication could be obtained by oil since the short time of contact did not permit its escape. The samples were compressed to a total true strain of 1.4 to 1.6. A larger sample was prepared similarly with spiral grooves in the ends to hold paraffin which provided essentially complete lubrication. This sam ple was compressed slowly at room temperature at a rate of about 2 per min to a total strain of 1.0. Cylindrical samples were carefully machined from these discs with a radial direction as an axis. They came from the center half of the samples and were roughly 1/16 in. in diam. The samples were etched down 15 pct to remove any surface effects. Diffraction data were then obtained for six different kinds of planes by the use of the Norton technique as applied to a fiber texture. Direct comparison between the raw data failed to reveal any significant difference between any of the samples and consequently the data from only one sample was completely reduced. The particular sample had been deformed at O°C The background was subtracted from the intensity data which were averaged over the four quadrants and then normalized to random. These data were then used to obtain fiber-axis distribution charts as previously described.2 For this sample the (422) plane was also run to assist in this inversion. The final result, Fig. 1, provided a comparable fit to that previously obtained from fiber data. About 85 pct of the material forms an elliptical texture around the <110> direction. The radius (at half height) is 5.5 deg along the (111) boundary and 8 deg along the (100) boundary. The remaining 15 pct forms a ridge running from this texture to near the <311> direction. The regions around the (100) and (111) planes are devoid of material. The earlier qualitative results of ~arrett~ are in complete agreement with the present results. The possibility has been dis-cused that the material around the <311> results from friction between the sample and compression plates.4 The present results are considered proof that such is not the case because of the uniformity of sample deformation and the requirement of axial symmetry before fiber-axis distribution charts can be accurately obtained. Recently results have been obtained to show that strain rate and temperature are important variables in the extrusion of aluminum.5 Perhaps the most important observation was that the partial recrystal-lization occurred even at room temperature. Strain rate was considered to be a factor only in that it produced a temperature change. There are many differences between the two experiments, the most important possibly being that their material was roughly ten times the purity of the present material. The present experiment, however, may not be as definitive as desired in this respect since it has been shown that compressed aluminum recrystallizes without a texture change6 although supplementary

Jan 1, 1961

By J. A. Roberson, A. M. Adair

A plate of an 18 pct Ni (250 grade) maraging steel was homogenized, cold rolled, and re crystallized to produce a fine grained, homogeneous structure. The strength properties were then measured as a function of cold rollinq prior to aging. Material in the solution heat treated condition exhibited substantial strengthening from cold rolling. The strength increase and the rate of strengthening were proportional to the amount of cold work. This benefit, of up to 50 ksi, was retained during aging for 3 hr at 900°F. The structures produced by cold rolling and aging have been systematically investigated by transmission electron microscopy. The dislocation debris produced by cold work influences the morphology and distribution of precipitate particles as well as the rate of precipitation. An essential feature of the high nickel maraging steels is a martensitic transformation from y to a with the resultant production of a supersaturated bcc solid solution. This solution decomposes to form precipitates during a subsequent aging treatment.&apos; The martensitic transformation in low carbon Fe-Ni alloys and the mechanical properties of these alloys have been studied extensively.2"4 The carbon content of maraging steel is kept very low to avoid the embrittling Fe3C phase and to minimize the acicular, or twinned martensite common to high carbon steels. Maraging steels are usually strengthened only by heat treatment, but cold working is also quite effective in this respect as was shown by Decker, Eash, and Goldman,&apos; Kula and Hickey,5 and the present work. There is, however, some disagreement between the present results and those of Kula and Hickey. Because of their unusual combination of strength and toughness, the maraging steels are suitable for applications where reliability at high stress levels is required. The strength level is achieved through a combination of solid solution hardening,&apos; substructure hardening,3 and precipitation hardening,6 of which the last is the most important. The toughness of these steels has been reported to be a result of the absence of brittle grain boundary precipitates,7 and the fact that the matrix is a massive martensite rather than a twinned martensite.&apos; One of the problems in the manufacture and use of maraging steel has been its tendency to develop laminations in sheets parallel to the rolling plane.9,10 The present investigation was intended to determine whether or not an improvement in the microstructure of this steel by thermomechani-cal processing would improve mechanical properties. I) EXPERIMENTAL PROCEDURES A plate ($ in. thick) of an 18 pct Ni-250 grade maraging steel* was obtained and examined metallo- "Analysis, wt pct: 18.1 Ni, 8.6 Co, 5.3 Mo, 0.4 Ti, 0.07 Mn, 0.05 Cr, 0.05 Si, 0.002B. 0.1 Cu. 0.05 Al. 0.002 Zr, 0.016 C, balance Fe. graphically. It was found to contain laminations as described by previous investigators. This plate was then annealed at 2100°F for 24 hr to promote homogeneity. Pilot studies on small coupons had shown that this was the minimum temperature required to accomplish homogenization in 24 hr. Since this treatment caused excessive grain growth, the steel was subsequently cold rolled and recrystallized. Cold rolling was accomplished at about 5 pct per pass to a total reduction of 66 pct. The standard solution annealing treatment (1 hr at 1500°F) was adequate to cause recrystallization of the cold worked steel. The recrystallized steel was then cold rolled and ground by various amounts to produce specimens with uniform thickness and selected amounts of cold rolling. All tensile specimens with less than 90 pct cold reduction were ground to a thickness of 0.050 in. Specimens with 90 pct cold reduction were 0.025 in. thick. All

Jan 1, 1970

By T. P. Meloy

The behavior of slime-sized particles in a flotation cell is neither well documented nor well understood. In general, slimes (or &apos;fines&apos; as they will be alternatively called in this chapter) have been either ignored, eliminated, or treated empirically. Recently, however, some good experimental and theoretical work has been done that leads qualitatively to a clearer understanding of the problems involved. Fines are small particles that, owing to their smallness, behave differently from larger particles of the same material. The smaller the particle, the larger is its surface-to-mass ratio. The difference in the surface-to-mass ratio for a micron-sized particle and a centimeter-sized particle is 10,000 to 1. For our purposes we shall arbitrarily define any particle less than 10 µ 10-3 cm) as being a fine. This is generally considered the upper limit of colloidal-sized particles. Recently, the field of colloidal chemistry has successfully used the concept of the double layer to explain dispersion and flocculation of fine particles in a static system. Flotation, however, is a dynamic system due both to the turbulence of the liquid and to the coursing of the bubbles through the cell. Further more, a flotation system is a heterogeneous system in which there are a number of different types of particles which interact with one another. A further difficulty is that no two flotation systems are the same for minute quantities of a variety of common chemicals will alter the behavior of the system. These reasons make reproducible experimental results that can ex- plain fine-particle behavior difficult to obtain. In spite of these experimental difficulties, millions of tons of ore containing a large amount of fines are successfully floated every year. For example, at the Morning mill of American Smelting and Refining Co., a galena concentrate that was 42% -6 µ and a sphalerite concentrate that was 33% -9 µ were floated leaving a tailing that was 27% - 9 µ.l Ores that contain fines can generally be divided into two classes. In the first are those in which the valuable mineral tends to slime, such as galena and hematite. In the other class, one or more of the gangue minerals forms the slime; a typical example is barite. Though the problems due to the presence of fines are often the same in handling the two classes of ore, the method of handling them is different because of economic considerations. Nonmetallic mineral flotation is particularly affected by slimes, by either slime-coating effects or excessive reagent consumption. Though a given gangue mineral may not float under the conditions prevailing in the flotation cell, it may still be able to adsorb the collector. I£ it also slimes, a significant

Jan 1, 1962

By E. P. Abrahamson II

The effect of transitiorz element bitzary solid solution additions upon the recrystallization temperature of columbium has been investigated. The elements Mn, Fe, Co, Ni, W, Re, and 0s OWY the yecystallization tempel-aturye, while Ti, V, CY, zr, Mo, Ru, Rh, Pd, Hf, Ta, W, Ir, and Pt mise it. A correlation is kloted between the rate of chatzge of recyystallization tewaperature with atomic hercent solute and the free atom electron configuration of the solute element. The work of Abrahamson and Grant1 has indicated a correlation between the free atom ground-state electron configuration and the change in brittle-ductile transition temperature per atomic percent solute in chromium base alloys. A similar correlation was observed for the change in the recrystallization temperature of iron base alloys by Abrahamson and Blakeney and Abrahamson. It was also observed that the limit of rapid change in recrystallization temperature also Correlated with the electronic configuration of the free solute atom. A further study by Abrahamson4 established the generality of the phenomenon by yielding similar results for vanadium base dilute alloys. It has been inferred that a peri- odicity might be expected with changes in the free atom electron configuration of the solvent element. This study is the third set of transition base metal systems to be studied. It is the object of this and further studies on transitional metal systems to detect any systematic variations in the observed correlation which might contribute to the understanding of the electron interactions which are evidently exhibiting themselves. PROCEDURE All alloys were made using 99.9 pct Cb with 0.030 Ta, 0.016 0, 0.0025 H, 0.003 Mo, 0.021 Fe, 0.005 C, and 0.002 N. The solute elements were 99.9 pct pure. According to the published binary phase diagrams5 and metallographic examinations at X750, all additions were in solid solution. The alloys were arc melted and remelted 6 times in the form of cubic 400-g buttons under an argon atmosphere. They were then hot forged at 1200oC to 0.6-in. diameter, annealed for 3 hr at 1200o under argon, and furnace cooled. The specimens were then machined to 0.400 -in. diameter. Grain size was checked and found to remain essentially constant at 150 i 30 grains per sq mm. The specimens were then cold swaged to 0.187-in. diameter, yielding 46 i 1 pct cold work. All alloys were chemically analyzed for the major solute. Analyses of random samples indicated that the impurity content remained at the values of the starting material. Tungsten contamination was held to 0.007 pet.

Jan 1, 1962

The Library of the above-named Societies is open frond 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated front sources of information. To these the Library, through Its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining neaps, and to furnish general information on the geology and mineral resources of all countries. All communications should he made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be, sent more promptly and in more usable shape.

Jan 1, 1917

For the -year ending February, 1920 PRESIDENT HORACE V. WINCHELL MINNEAPOLIS, MINN. PAST PRESIDENTS PHILIP N. MOORE ST. Louis, Mo. SIDNEY J. JENNINGS NEW YORK, N. Y. FIRST VICE-PRESIDENT A. R. LEDOUX NEW YORK, N. Y. TREASURER GEORGE D. BARRON NEW YORK, N. Y. SECRETARY BRADLEY STOUGHTON NEW YORK, N. Y.

Jan 5, 1919

For the year ending February, 1920 PRESIDENT HORACE V. WINCHELL MINNEAPOLIS, MINN. PAST PRESIDENTS PHILIP N. MOORE ST. LOUIS, Mo. SIDNEY J. JENNINGS NEW YORK, N. Y. FIRST VICE-PRESIDENT A. R. LEDOUX NEW YORK, N. Y. TREASURER GEORGE D. BARRON. . . . &apos; NEW YORK, N. Y SECRETARY BRADLEY STOUGHTON NEW YORK, N. Y

Jan 6, 1919

Jan 1, 1943

By W. Rostoker, S. A. Spachner

FOLLOWING the discovery of the w transition phase in certain titanium-chromium alloys by Frost, Parris, Doig, and Schwartz, much interest has centered on the alloys in which this phase is found and its mode of precipitation. The w phase has been found in alloys of Ti-Cr, Ti-Fe, Ti-Mn, Ti-MO,2 and Ti-v.3 The temperature-time-transformation characteristics have, as yet, not been determined for most of these. In this study, such transformation characteristics have been investigated for two heat-treatable titanium alloys known to exhibit transition phase phenomena. The alloys chosen, Ti-8Cr and Ti-13M0, are representative of two classes of binary equilibrium systems. In the

Jan 1, 1959