Search Documents

By R. M. Brick, R. G. Treuting

DESPITE the basic importance of slip in the plastic deformation of metals, and the considerable experimental investigation, thought, and speculation that have been devoted to the fundamental nature of these processes, surprisingly few data have been reported regarding the microscopic appear- [ ] ance and distribution of slip lines,[$] the external manifestation of the slip process. Photographs hitherto reproduced in the literature are in general at low or unspecified magnifications with no correlation to the prior shear. A single-crystal cylindrical tensile specimen of alpha brass about ½ in. in diameter, one of many previously prepared by H. L. Burghoff,1 was available for study. A plane about 3/16 in. wide, parallel to the specimen axis and normal to the plane containing the slip direction and the specimen axis, was ground and metallographically polished along the entire 5-in. gauge length. Heavy etching produced a surface free of both scratches and flow. The specimen was strained in tension until slip markings first became visible on the polished surface (Figs. I and 2). Restressing the crystal caused additional markings to appear at an initially lower [ ] stress than previously was required. Stretching the specimen to produce a dense concentration of slip lines caused such variations in level in the polished surface (normal to the slip direction) that microscopic study at higher magnifications became impossible. After annealing 15 hr. at 850°C., the specimen recrystallized to form two grains with a boundary approximately normal to the specimen axis and about midway along its length. Each was X-rayed, and two planes were again polished along the length of the specimen, in this case each parallel to the slip direction in one of the two crystals. A light longitudinal scratch parallel to the specimen axis was drawn down the center of each plane. A Huggenberger extensometer was attached to the crystal A, whose slip plane would have the higher resolved shear stress of the two, and the specimen was again strained in tension.

Jan 1, 1941

By M. Cohen, W. J. Harris

The recent application of lineal analysislt2 to the austenite-martensite reaction has made possible a quantitative study of the kinetics of this transformation during rapid cooling. Martensite range curves can thus be constructed to portray the onset of the reaction at Ma and its subsequent progress as a function of temperature down to and below the ambient. It now seems in order to investigate other aspects of the martensite transformation, using this quantitative method of approach. One of the least understood characteristics of the austenite-martensite reaction is that of stabilization which has been defined by Troiano and Greninger3 as 'la lowering of Ma, resulting from aging, without change in chemical composition of the parent solid solution." In other words, if the hardening quench is arrested at a predetermined subcritical temperature (TA) for a sufficient period of time, more austenite may be retained at a given lower Or reference temperature (Tr) than if the steel had been cooled directly and rapidly to Tr in the first place. For the purposes of the work at hand, the extent of stabilization produced by the isothermal treatment at Th is measured explicitly in terms of the excess austenite (6) that exists in the steel at T,, over and above the amount that is normally present after direct quenching to T,. T, is conveniently taken to be room temperature, but this choice is not essential and is sometimes undesirable. The holding temperature (TA) may be above or below M,, and still cause stabilization depending upon the themistry of the austenite. stabilization has been found to occur in the presence of bainite4 and of martensite6,6,7,8 as well as in the absence of either,g The phe-nomenon of stabilization is not concerned with (and may even be obscured by) ferrite formation or any other type of phase change occurring at T~ that alters the chemistry of the remaining austenite. Such a structural change would obviously influence the martensite transformation during subscquent cooling. Stabilization, however, is more subtle; it appears to manifest itself without detectable variation of the austenite composition, whether in the presence or absence of transformation products. There are relatively few direct references to stabilization in the literature. The stabilizing effect of room temperature aging and tempering on the subzero transformation of retained austenite has been clearly shown in plain carbon,6,8 low alloy6s7.8 and high alloy tool steels.10'5 ssa- with the as-hardened steel, the degree of stabilization increases with tempering time and temperature through

Jan 1, 1949

The Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties. United Engineering Trustees, Inc. When Mr. Carnegie made his gift which made possible a home for the engineering societies, a separate corporation was organized to act as a holding company and to manage the common property. This was long known as the United Engineering Society, but the name has now hen changed to one which more nearly reflects the real function of the corporation. It holds title to the Engineering Societies Building and to various funds placed in its charge and is managed by a Board of Trustees, of which three are chosen by each of the four societies, American Institute of Mining and Metallurgical

Jan 1, 1932

By Enid C. Plante, K. L. Sutherland

PRACTICAL metallurgists are unanimous in stating that oxidation of mined sulphide ore adversely affects separation of the constituent minerals under standard conditions in a mill. Frequently, the need for different operating conditions in different plants is attributed either to the extent of oxidation of the mineral surfaces or to soluble oxidation products. The investigations reported in this paper study the effect of oxidation on the primary condition necessary for flotation, namely that of adhesion of an air bubble to the mineral. OXIDATION PRODUCTS FROM SULPHIDE MINERALS Weinig and Carpenter1 state that the relative rates of oxidation of some sulphides are: FeAsS > FeS2 > CuFeS2 > ZnS >PbS > Cu2S tetrahedrite. They also show that oxidation is rapid at first, that sulphides of older geological formations are more stable than those of recent date and that mixtures oxidize more rapidly than any one mineral alone. The more rapid oxidation of mixtures is borne out by results of Gottschalk and Buehler2 who found that PbS, ZnS and CuS oxidized 8 to 20 times faster when pyrite was present. Only the end products of oxidation, sulphate and the metal ion, were identified in these tests. Gaudin3 states that pyrite is difficult to oxidize in the laboratory. Winchell,4 using pyrite containing 99.98 pct FeS2, allowed water to percolate through a bed of this ground material. At the end of three months only a trace of Fe +++and S04- were found. Even after 10 months the quantity of Fe+++ was only 7.8 mg and S04- 25.5 mg per liter of percolating solution. Carmichael5 confirmed Winchell's results on the slow oxidation of pyrite. Usually the oxidation of sulphide surfaces has been conducted in neutral or acid solutions, the acidity being caused by the oxidation products. Eliseev and Nagirnyak6 found that treatment of pure pyrite with lime gave only thiosulphate, but considered it possible that thiosulphate was obtained not by oxidation of the pyrite itself, but by oxidation of calcium disulphide. Mitrofanov7 suggested that thiosulphate was formed by the following process: oxidation of sulphide to give free sulphur (this frequently happens with marcasite), followed by oxidation of the sulphur to sulphur dioxide and reaction of the sulphur dioxide with sulphur to give thiosulphate. Ferric and ferrous hydroxides, or similar compounds, were shown to be present. The Research Staff of the United Verde Copper Co.8 treated ore from the United Verde mine with lime. Thiosulphate, sulphide and polysulphides were stated to be

Jan 1, 1947

H. W. Turner, San Francisco, Cal. (communication to the Secretary*): This excellent paper apparently represents the results of extensive observation and experience among the mines of the Mother-Lode, but I strongly question its relegation of the dioritic intrusions to the period of fissuring and ore-deposition. The dioritic rocks referred to are evidently those areas represented by Ransome in the Mother-Lode folio1 as meta-diorites, and, as he says, are merely basic facies of the great granodiorite batholite of the Sierra Nevada. If followed downward I venture to predict that these meta-diorite areas would be found to connect with the great batholite, and to be in fact mere apophyses of it. I see no reason for supposing that these apophyses were intruded into the Mother-Lode slates at a period later than the intrusion of the granodiorite in general. The period of fissuring was subsequent to this intrusion; the basic granodiorite or quartz-diorite areas of the foot-hill region are themselves fissured extensively; and the fissures were filled with quartz, apparently during the same general period of the formation of the Mother-Lode veins. Prichard and Ransome2 both refer to the deposition of quartz in the same lode at different periods resulting from a reopening of the fissures. Some time since, I saw in the stopes of the

Jan 1, 1904

The members of the Institute will recall the account given in the March Bulletin of the inauguration exercises of the Engineering Foundation which was inhibited by an initial gift of $200,000 by Mr. Ambrose Swasey, to be administered by the United Engineering Society as trustees. The Engineering Foundation Board is now constituted as follows: GANG DUNN, Chairman, EDWARD D. ADAMS, Vice-Chairman FREDERICK R. HUTTON, Secretary, JOSEPH STRUTHERS, Treasurer, American Society of Civil Engineers. J. WALDO SMITH, CHARLES WARREN HUNT.

Jan 12, 1915

By A. Cochardt, D. H. Feisel

HE success of the sintered aluminum powder material (SAP)' in raising the maximum useful temperature of aluminum alloys has stimulated effort in investigating similar systems in which the metallic matrixes have higher melting points. Examples of such systems which have been studied are nickel-alumina,2, 3copper-silica,4 copper-alumina,4 titanium-cerium oxide,5 and 80/20 nickel-chromium,8 cobalt,= and molybdenum7 matrixes with various hardeners. Conventional precipitation-hardened high-temperature alloys are often thermally unstable in service. The original fine particles that are responsible for good strength properties grow in size at elevated operating temperatures, a process termed "over-aging." This growth of precipitated particles causes a gradual loss in strength properties. A previous paperb describes the factors that govern the process of overaging, and estimates the time required for overaging of a nickel-alloy matrix dispersion-hardened by various precipitates such as are found in current high-temperature alloys, and by alumina. These calculations indicate that nickel-base alloys hardened with Ni3Al, Tic, or TiN are quite unstable at 1340" F (727°F). Such alloys should overage within a few hours at that temperature. A nickel-base alloy hardened with alumina, on the other hand, should behave differently. It should not overage appreciably within a thousand years. It was further shown8 that the thermal stability of the oxide-hardened alloy is mainly due to the low solubility of oxygen in equilibrium with alumina in the nickel-base matrix. Since the oxygen solubility is small, little oxygen can diffuse, and structural changes require very long times. This paper illustrates the effects of time and temperature on the structural stability of nickel alloy matrixes hardened by dispersions of Ni3A1, Ni3Ti, Tic, and alumina, and of nickel-chromium matrixes hardened by alumina. Hardness measurements and metallography have been used as a measure of structural stability. EXPERIMENTAL PROCEDURE Using the best information from published phase diagrams,'-l4 compositions of the Ni-Al, Ni-Ti, and Ni-Ti-C alloys were determined so as to have 5 vol pct of precipitate at 1350° F(732°C), the temperature selected to illustrate the effect of time on structural stability. Table I lists the chemical compositions of these alloys. Standard laboratory melting and alloying techniques were used in preparing ingots of the F-Series of alloys. The cast ingots, 1 3/4 in. in diam, were forged to 3/8-in. diam rods.

Jan 1, 1960

By W. A. Hustrulid, N. A. Ross

An analysis of the design of medium to hard rock tunneling machines is presented. The developed equations are used to compare performances and machine requirements using kerf and fixed pick cutters to bore a given rock. With the use of pick cutters, required thrusts can be greatly reduced and still achieve the same boring rate as with present day tooth or kerf cutters. It appears that the cutting coefficient, which for most boring machines is of the order of 0.1, should be increased to one or larger to facilitate rock removal by cutting rather than grinding. The depth of cut and the indexing distance should be greatly increased to make use of inherent rock weakness.

Jan 1, 1971

By James Aston

INDICATIVE of the practical importance of the achievement of James Aston , recipient of the Robert W. Hunt Medal for 1930, is the following prosaic item from the financial columns of a recent issue of a New York newspaper. "According to private advices from Pittsburgh, production costs of the A. M. Byers Co. for 1929 were reduced about $5 a ton by the use of the Aston process for making wrought iron pipe. A greater saving is anticipated for 1930, when more of the company?s requirements will be produced by the new method."

Jan 1, 1930

[ARIZONA Established July 10, 1915 CHARLES R. KUZELL, Chairman GILBERT C. DAVIS, First Vice-Chairman ALBERT MENDELSOHN, Second Vice-Chairman MORRIS G. FOWLER, Secretary-Treasurer Phelps Dodge Corporation, Douglas, Ariz. LYLE M. BARKER P. D. I. HONEYMAN A. T. BARR H. M. LAVENDER T. G. CHAPMAN WALTER C. LAWSON GEORGE M. COLVOCORESSES W. H. LOERPABEL EDWIN H. CRABTREE, JR. CARL F. MILLS WALTER I. GARMS P. M. MOSIER WESLEY P. Goss J. A. RICHARDS 11. C. HENRIE JOSEPH A. WILCOX C. F. WILLIS]

Jan 1, 1946

ELECTROREFINING Canadian 1,023,691 -Removal of bismuth from slime filtrate in the Betts process refining of lead. The filtrate is subjected to electrolysis in a cell having an anode of crude lead and a cathode of refined lead under operating conditions to preferentially deposit bismuth on the cathode. The substantially bismuth-free filtrate is recycled for use in the process as the electrolyte for producing high-purity lead. S. Hirakawa and R. Oniwa, assigned to Mitsui Mining & Smelting Co., Ltd. Jan. 3, 1978. 8 pp. (204-73). Filed: 2-18-74 (192,810). Same: U.S. 4,026,776, dated May 31, 1977.

Jan 1, 1979

By George W. Toth

This paper describes the features of a computer cost model developed to estimate requirements and costs of individual coal mining projects. Detailed cost analysis procedures for both coal mining and preparation are incorporated into the model. This model has been developed over a period of seven years through funding provided by the Electric Power Research Institute (EPRI). The model follows a process engineering approach for the estimation of all project capital and operating costs. A discounted cash flow analysis procedure is also designed into the model to allow for the solution of cost/ton or cost/MMBtu of clean coal production. The model can be applied to most surface or underground mining deposits and can accommodate a wide variety of coal washing situations. This flexibility makes the model a particularly useful tool for preliminary project analysis, property screening, investment analysis, mining technology assessment, coal cleaning level assessment, and general property valuation.

Jan 1, 1983

By Charles E. Lundin

Pressure-temperature-composition data were obtainedfor the Er-H system. Measurements werecar-ried out in the temperature range of 473° to 1223°K, the composition range of erbium to ErH,, and the pressure range of 10-5 to 760 Torr. Solubility relationships were established from these data throughout the system. Three solid-solution phases were delineated: metal solid solution, dihydride phase, and trihydride phase. The trihydride Phase decomposes at about 656°K and 1 atm pressure. The dihydride phase is stable to about 1023°K, but becomes more deficient in hydrogen above this temperature. The equilibrium decomposition pressure-temperature relationships in the two-phase regions, erbium solid solution plus dihydride and dihydride plus trihydride, were deter- The differential heats of reaction in these two regions are AH = - 52.6 * 0.3 and - 19.8 i 0.2 kcal per mole of Hz, respectively. The differential entropies of reaction are AS = - 35.2 * 0.3 and - 30.1 * 0.4 cal per mole HZ.deg, respectively. Relative partial molal and integral thermodynamic quuntities were calculated in the system to the dihydride phase. RARE earth metal-hydrogen systems have been the subject of general survey,1"4 and all have been found to form hydride phases. The heavy rare earths, of which erbium is a member, form dihydride and trihydride phases with different crystal structures, whereas the light rare earths form only a single-phase dihydride which expands without structure change, as hydrogen is added, to the trihydride composition. These materials are of interest primarily because of their theoretical properties, such as bonding, defect structure, and thermodynamic and electronic characteristics. Erbium has been studied in several previous investigations.5, 6 It was deemed desirable to more thoroughly and accurately define the system, both for the phase equilibria and the thermodynamic properties. I) EXPERIMENTAL PROCEDURE A Sieverts&apos; apparatus was employed to conduct the experimental measurements. Briefly, it consisted of a source of pure hydrogen, a precision gas-measuring buret, a heated reaction chamber, a mercury manometer, and two McLeod gages (a CVC, GM 100A and CVC, GM 110). Pure hydrogen was obtained by passing hydrogen through a heated Pd-Ag thimble. The hydrogen was analyzed and found to have only a trace of oxygen and nitrogen. A 100-ml precision gas buret graduated to 0.1-ml divisions was used to measure and admit hydrogen to the reaction chamber. The reaction unit consisted of a quartz tube surrounded by a nichrome-wound furnace. The furnace temperature was controlled by a recorder-controller to ±1°K. An independent measurement of the sample temperature in the quartz tube was made by means of a chromel-alumel thermocouple situated outside, but adjacent to, the quartz tube near the specimen. Pressure in the manometer range was measured to ±0.5 Torr and in the McLeod range (10-4 to 10 Torr) to ±3 pct. The hydrogen compositions in erbium were calculated in terms of hydrogen-to-erbium atomic ratio. These compositions were estimated to be ±0.01 H/Er. The erbium metal was obtained from the Lunex Co. in the form of sponge. The metal was nuclear grade with a purity of 99.9 pct +. The oxygen content was reported to be 340 ppm and the nitrogen not detectable. Metallographically the structure was almost free of second phase (<1 vol pct). A quantity of sponge was arc-melted for use as charge material. The solid material was compared with the sponge in the pressure-temperature-composition relationships. They were found to be identical. Therefore, sponge material was used henceforth, so that equilibrium could be attained more rapidly. The specimen size was about 0.2 grain for each loading of the reaction chamber. The procedure employed to obtain the pressure-temperature-composition data was to develop experimentally a family of isothermal curves of composition vs pressure. First, a specimen of erbium was wrapped in a tungsten foil capsule to prevent contact with the quartz tube. After loading the specimen, the system was evacuated to less than l0-6 Torr, flushed several times with high-purity hydrogen, and evacuated again ready for the start of the experiment. The furnace was then brought to the desired temperature. A measured amount of hydrogen was admitted into the chamber. Equilibrium was allowed to be attained, the pressure read, and the process then repeated many times until 1 atm of gas pressure was finally reached. Other isotherms were then developed in the same manner. The partial pressure plateaus were determined by another manner. In the solid solution-dihydride region a composition of approximately 1.0 H/Er was selected on the plateau. The temperature was varied throughout the range of interest. At each temperature level, equilibrium was achieved, the pressure read, and the next temperature attained. The temperature was cycled both up and down. In the dihydride-trihy-dride region, the plateaus were determined in the 473" to 651°K range only by heating to the desired temperature and not by both heating and cooling. The data were much more reproducible in this manner. Equilibrium required long periods of time. Specimens were initially hydrided to 2.8 H/Er, so that at the higher

Jan 1, 1969

By R. P. E. Hermsdorf

THE electrolytic refining of metals for the removal of undesirable impurities has become a recognized necessity in the nonferrous field. Copper, lead, zinc, nickel, silver and gold have been produced in this manner for years. The United States Metals Refining Co., realizing that considerable quantities of lead and tin could be made available to the trade if a satisfactory method of purification of these metals could be established, decided to investigate the possibilities of electrolytic solder. In cooperation with Dr. Edward F. Kern, of the School of Mines at Columbia University, the company developed a process of electrolytic refining of lead-tin alloys using a tin-lead fluosilicate electrolyte. A pilot plant was installed in November, 1927, and the commercial unit was put in October, 1929. Since that time thousands of tons of electrolytic solder have been produced in this plant and consumed by all branches of industry that use solder.

Jan 1, 1936

By Giovanni B. Barla, Stefan H. Boshkov

The block caving method is examined in this paper on the basis of experimental results and observations in the field, and through the use of numerical modeling by the Finite Element Method. The Grace Mine, developed by a panel caving method, served as a reference case. However, the results obtained and the simulation techniques which have been developed may find useful application in more general conditions as encountered in other mining operations by block caving. Following a brief description of the Grace Mine and of the mining method, the problems associated with the behavior of underground drifts at the production levels, during undercutting and caving, are addressed. The most important results obtained through monitoring of strains and loads in the supports of a runway are discussed, while giving relevance to the sequence of mining operations in the immediate vicinity. The most important geomechanical data, as provided for subsequent modeling, are described with reference to: (a) rock mass characterization and (b) in situ state of stress. Then, the numerical modeling procedures, developed by the Finite Element Method in order to predict the caving phenomena and the behavior of underground openings during undercutting, are discussed. Finally, an attempt is made to compare the pre- dictions of the numerical analyses with, the measurements carried out at the instrumented site. Suggestions as to how to improve the results both qualitatively and quantitatively are also given.

Jan 1, 1984

By William G. Kranz

Discussion of the paper of WILLIAM G. KRANZ, presented at the San Francisco meeting, September, 1915, and printed in Bulletin. No. 101, May, 1915, pp. 927 to 930. M. PETINOT, Niagara Falls, N. Y. (communication to the Secretary*). -I have read this paper with considerable interest and agree perfectly with Mr. Kranz that steel for castings made in an electric furnace is not necessarily, because of that fact, all good steel, and also that the qualities which he mentions, such as absence of segregation, elimination of `sulphur, great tenacity, etc., can be obtained in an electric furnace if operated under proper metallurgical conditions. An unusually low content of sulphur in steel for castings is not, of course, an absolute necessity and the range of this element usually obtained in steel made in basic open-hearth furnaces is sufficiently low to meet all physical requirements. The main factor in making steel for castings, regardless of the process, is the complete deoxidation of the bath to prevent the formation of

Jan 12, 1915

By S. K. Ruggieri, R. A. Jankowski

Airborne respirable dust levels on longwalls can be reduced if operators approach the dust control problem in a logical and fundamental manner. This can be accomplished through the proper application and continued use of effective dust control techniques. The Bureau of Mines is currently assessing the effectiveness of longwall dust control techniques in use today to provide mine operators with guidelines for selecting the most appropriate control technology. This paper presents a fundamental approach to the problem of shearer dust control. Three dust control techniques to be discussed are: deep cutting/increased pick penetration for reducing the amount of respirable dust generated; drum water sprays/improved water supply system to suppress the amount of airborne respirable dust; and improved external water spray system, the “shearer-clearer, "to push the dust close to the face. The techniques have been evaluated infield trials and have been shown to be both practical and effective in applications to control shearer generated dust.

Jan 1, 1985

By Peter R. Morris, Alan J. Heckler

THREE angles are required to specify the orientation of a crystallite with respect to a physical reference frame. The distribution of crystallite orientations in a polycrystal is thus a function of three angular variables. The most widely used experimental techniques for studying orientation in polycrystals lead directly to the pole figure representation, i.e., the distribution of the poles of certain crystallographic planes in terms of two angular variables. In recent years1-5 methods have been developed which permit determination of the (three-angle) crystallite orientation distribution from several (two-angle) pole figure distributions. In this work Roe&apos;s method has been applied to the study of orientation in hcp materials. The method is illustrated for commercial purity titanium sheet (Ti-70) which was cold rolled (65 pct reduction), annealed at 1450°F for 3 min, and air cooled. The grain shape was observed to be equiaxed after this treatment. EFFECTS OF PHYSICAL, CRYSTALLOGRAPHIC SYMMETRY In Roe&apos;s method the crystallite orientation distribution, w(?,?,F), is expanded in a series of generalized spherical harmonics 11(?,?,F) = E E E W^Zirmtye-tote-in* [l] 1=o ,,,=-I ,,=-I where { = cos 8. The set of Euler angles employed here is illustrated in Fig. 1. The axis for each rotation is denoted by a double arrowhead. The positive sense of each rotation is that of a right-handed screw advancing in the direction of the double arrowhead. The X, Y, and Z directions correspond to the rolling direction, cross direction, and normal direction, respectively. In the initial orientation (10.O), (12.O), and (00 . 1) planes are perpendicular to the X, Y, and Z directions, respectively. The IC/ rotation about the Z axis is carried out first by rotating X into X&apos;, Y into Y&apos;, and leaving 2 unchanged, i.e., Z&apos; = Z. The 8 rotation about the Y&apos; axis is carried out second by rotating X&apos; into X", 2&apos; into Z", and leaving Y&apos; unchanged, i.e., Y" = Y&apos;. The I$ rotation about the Z" axis is carried out last by rotating X" into X"&apos;, Y into Y"&apos;, and leaving 2" unchanged, i.e., 2"&apos; = 2". Any specified orientation of the X&apos;", Y&apos;", and Z&apos;" crystal-fixed axis system relative to the X. Y, and Z physical axes (rolling direction, transverse direction, and sheet normal direction, respectively) can be obtained by appropriate IC/, 8, and (F rotations. The Zl,, of Eq. [l] are the Jacobi polynomials, augmented by the square root of the weight function. The Zl,, are symmetric in m,n, i.e., Zl,,= Zlnm. For orthotropic physical symmetry and hexagonal crystallographic symmetry, the coefficients, W!,,, of the series are all real, W!mn = Wzfi, = Wlm~ = Wlfi~, 1 and m are even and n is restricted to 6k, where k = ...,-2,-1, 0, 1, 2, .-.. The determination of the Wlmn from pole figure data has been previously described.&apos;~~ The Zl,, may be written in multiple angle form

Jan 1, 1970

In reply to inquiries and comments which have reached me since the publication of this paper, and in explanation of some seeming discrepancies between my statements in the text concerning the amount of displacement of the faults, on one hand, and certain figures in the plates on the other hand, I give here, with some additional remarks, my measurements of the displacements in the different sections, which it originally seemed unnecessary to print : By displacement, I mean neither the throw, i.e., the vertical distance apart of the two edges of a faulted bed (what Mr.

Jan 1, 1896

PUBLIC hearings began before the Committee for Reciprocity Information on May 24, 1950, for the purpose of unearthing data and opinion that will be helpful in the forthcoming reciprocal tariff and other trade-barrier negotiations at Torquay, England, on September 28th of this year. The conference this fall will constitute the "third round" of tariff negotiations under the General Agreement on Tariffs and Trade concluded at Geneva in 1947. The United States plans to negotiate with 17 other countries on possible tariff modifications on various articles all the way from baby carriages and bottle caps to lead and zinc-bearing ores. On May 31, June 1 and June 2, spokesmen appeared before the Committee for Reciprocity Information on behalf of the domestic lead and zinc mining industries. Producers of these metals protested the inclusion of paragraphs 391 (lead-bearing ores, dust and mattes), 392 (lead bullion, lead in pigs and bars, and scrap lead), 393 (zinc-bearing ores of all kinds), and 394 (zinc in blocks, pigs or slabs, and zinc dust) of the Tariff Act of 1930, as amended in the list of articles to be considered for possible tariff concessions at Torquay. It was pointed out that although operating costs have more than doubled since 1939 tariffs on these metals were actually higher in that year than at present. This, coupled with the detrimental effects of the recent series of devaluations, has sounded the death knell for a substantial number of domestic lead and zinc mines-a most undesirable development in the face of the ominous international situation, according to these spokesmen. It was urged that higher rather than lower tariff rates are needed on these metals. The opinion was expressed that it was inconsistent to foster a high living standard in our western areas and then, once it is attained, to undermine that condition by minimizing the protection that was partly responsible for it. The main theme of some arguments implied that although every effort should be made to close the "dollar gap" abroad, serious consideration must be given the methods employed lest our national security position be jeopardized in the process. The House Committee on Foreign Affairs completed hearings on H. J. Res. 236, to provide for United States membership and participation in the International Trade Organization. Hearings began on April 19th and ran for over five weeks. Many witnesses from industry and government presented voluminous testimony, which will not be available for public distribution for several weeks. However, it is no secret that the most controversial provisions of the Draft Charter of the ITO are: (1) Article 17 (Chapter IV on Commercial Policy) which would obligate members to negotiate for the reduction of tariffs and the elimination of trade preferences; (2) Article 20 which would prohibit the use of quantitative restrictions for protective purposes; (3) Article 16 which promulgates rules to implement the principle of non-discrimination in international trade; and (4) provisions permitting the use of protective measures for promoting economic development, particularly in backward areas, even though such provisions are inconsistent with those of the three articles cited above. United States membership in the International Trade Organization is essential to the successful operation of that body in view of this country&apos;s position as the economic giant in the present international trade pattern. Many countries are reluctant to take any action toward the ratification of the charter until it is known what course America will pursue. However desirable or undesirable the ideal of free multilateral trade may be it is unlikely that this Government&apos;s participation in the ITO will materialize soon. Advices in Washington indicate that H. J. Res. 236 will not be enacted during the present session of Congress. The legislative pattern designed to secure Congressional approval of the ITO is similar to that of the St. Lawrence Seaway project. The Seaway project was pending in treaty form for several years before the Foreign Relations Committee of the Senate and when the Administration decided to incorporate this project into bill form it was found that, while it passed the House promptly, the Senate decided to pigeonhole it because of the obvious intent to circumvent the constitutional prerogative of the Senate to advise and consent to the ratification of treaties. The ITO bill may be slated for a similar fate. It is deemed essential by western Senators and Congressmen that the present session of Congress enact some form of mining legislation before its adjournment, now set for July 31st. These legislators from prominent ore-producing states do not desire to return to their home areas in the fall emptyhanded. Aside from that, it is entirely superfluous to reiterate the necessity for maintaining a healthy domestic mining industry as a bulwark against a sharp rise in the temperature of the "cold war". Now that S. 2105 has failed a new bill is taking shape in the Senate Interior and Insular Affairs Committee. It is similar in language to H. R. 8221 (to encourage the conservation and development of the mineral resources of the United States) reported by the House Public Lands Committee on May 3, 1950, but so far has failed to receive approval of the House Committee on Rules. There are some qualified observers in high circles in Washington as well as in the mining industry who favor a tax incentive program to stimulate investment in mining enterprises, as opposed to a conservation and exploration program. The Bureau of Mines and the Treasury Department have undertaken a joint study to determine the need for modification of the tax laws as they apply to mining. The study is scheduled for completion before the end of the year, and appears to be supplementary to the investigation initiated by the National Minerals Advisory Council which culminated in the submittal of recommendations to the Secretary of the Interior in December 1949. The "cold war" is largely responsible for the increased demand for metals. Stock-pile purchases and heavy industrial demand due to military needs distort markets and disrupt normal price trends. Such activity has an unhealthy influence on metal production, luring some producers into a state of dependency on the continuation of this condition. When stock-pile objectives are met sometime in the future purchases must then come to a halt unless international "fireworks" are touched off. It can only be hoped that technological improvements and further mechanization of mines coupled with the stimulus of a rising population will offset the anticipated drop in industrial demand and cessation of stockpile purchases when the international crisis abates.

Jan 7, 1950