Search Documents

By Frederic Dewey

HAVING shown1 the difficulty of assaying so-called cyanide bullion and the extreme variations often found in the results, an investigation was undertaken to discover if possible the causes of these variations by a series of tests upon the specific action of various metals during cupellation. Zinc.-In order to test the effect of zinc, 48 assays were made in sets of 6, 2 rows of 3. The charge for the middle cupels consisted of 500+ mg. Au, 1,125 mg. Ag, 10 mg. Cu. To the end cupels 50, 75, 100 and 125 mg. Zn were added, and a set of each proportion was cupelled with 4 and 8 grants Pb. The cupels were assayed and showed the following gold contents in milligrams, the figures being arranged as the cupels stood in the muffle: TABLE 1 50 Mg. Zn 75 Dig. Zn 100 Mg. Zn 125 Mg. Zn 4 grams, Pb 0.2S 0.25 0.2S 0:29 0.27 0.34 0.33 0.28 0.41 0.31 0:30 0.36 0.30 0.33 0.34 0.31 0.31 0.29 0.35 0.37 0.42 0.41' 0.34 0.38 8 grams, Pb 0.40 0.43 0.42 0.38 0.36 0.43 0.35 0.34 0.41 0.33 0.37 0.37 0.54 0.17 0.59 0.44 0.43 0.43 0.38 0.39 0.41 0.57 0.38 0.46 _ In many instances the zinc does not appear to affect the cupel gold, but various exceptions are apparent, generally in the cupels in the back row. With 100 and 125 mg. Zn, in some cases the Zn burned with its characteristic flame before it could alloy with the other metals. Also, less fusible oxidized lumps were observed during the cupellation and some cupels showed a scum. In order to lessen the premature burning out of the Zn, an alloy of 2 parts Ag to 1 part. Zn was used. A uniform charge of 500,+ mg. Au,

Jan 7, 1917

By J. B. Clemmer, P. E. Churchward, C. Rampacek

A cyclic method for processing manganese ores using sodium sulphate as the basic reagent is described. Sodium sulphate is electrolyzed in a diaphragm cell to give an anolyte-containing agentisdescribed.Sodiumsulphuric acid and a catholyte-containing iselectrolyzedincaustic soda, a part of which is carbonated in a cyclic manner to form soda ash. The reduced ore is leached with the anolyte to dissolve the manganese and the impurities are precipitated by addition of catholyte. Manganese in the pregnant todissolvethemanganeseandtheimpuritiessolution is precipitated as synthetic rhodochrosite with a carbonated catholyte, and sodium sulphate is regenerated. Calcining the manganese carbonate gives a high grade product and the carbon dioxide is returned to the carbonation step. The results of laboratory tests using cells equipped with synthetic-fiber diaphragms and permselective membranes, which permit transfer of anions or cations during electrolysis, are described. A METHOD which has been considered for pro-cessing manganese ores under emergency conditions to recover a product suitable for smelting to ferromanganese involves reductive roasting of the ore for leaching with dilute sulphuric acid followed by precipitation of the manganese from the purified pregnant solution with sodium carbonate. Although the process is operable and involves no novel or untried steps, it is noncyclic in regard to reagents. Research seemed warranted to determine if a cyclic process could be developed by electrolyzing the sodium sulphate formed during precipitation of the manganese with soda ash to regenerate sulphuric acid and sodium hydroxide. Reduced ore would be leached with acid anolyte to dissolve the manganese. The iron, alumina, and other dissolved impurities would be precipitated with the caustic catholyte, and the manganese in the purified pregnant solution would be precipitated as artificial rhodochrosite with carbonated catholyte to regenerate simultaneously sodium sulphate for electrolysis. Waste boiler gas and CO, from calcining the manganese precipitate would be recycled for carbonation of the caustic catholyte. There is a surprising lack of data in the technical literature on diaphragm electrolysis of sodium sulphate. One of the more comprehensive papers, by Atwell and Fuwa, describes the problem involved in electrolyzing byproduct sodium sulphate from the viscose process with particular regard to the design and operation of asbestos diaphragm cells. Frisk' also investigated electrolysis of sodium sulphate from viscose-spinning baths to recover caustic soda and sulphuric acid. The objective in these investigations was to produce, by electrolysis and evaporation, a concentrated caustic-soda solution and a sulphuric-acid solution low in sodium sulphate. Because of these requirements, the process was not too attractive despite a favorable yield of caustic and acid with a reasonable power consumption. Because strong acid and base are not required for processing manganese ores and nonelectrolyzed sodium sulphate is not objectionable in either reagent, the present problem was somewhat simpler than that of these investigators. The purpose of this report is to summarize briefly the results of laboratory electrolysis of commercial sodium sulphate in diaphragm cells of different types and the application of the acid and caustic for processing manganese ores in a cyclic manner. Electrolysis in Permeable Diaphragm Cells The principal problem in electrolyzing sodium sulphate in a permeable diaphragm cell is to prevent mixing of the acid and base formed in the anode and cathode compartments. It is not enough to separate the anolyte and catholyte by a single diaphragm. A three-compartment cell in which the sodium-sulphate solution is fed to the center compartment and flows through the permeable diaphragms to the anode and cathode compartments is more efficient electrically. Diaphragms should be porous enough to allow flow of solution to outer compartments but tight enough to prevent gross mixing of the anolyte and catholyte. In addition to being resistant to acid and alkali, the diaphragms should offer minimum resistance to the flow of current. It is also important that the electrolyte contain a high concentration of sodium sulphate to furnish an abundance of sodium and sulphate ions and thereby decrease the current carried by hydrogen and hydroxyl ions. A practical limitation of sodium-sulphate concentration is imposed by the decreased solubility of sodium sulphate with decreasing temperature. At 20°C, a concentration of 200 g per liter sodium sulphate can be maintained. Little is gained in conductivity by using a concentration greater than 200 g per liter. The small-scale continuous electrolysis tests were made in a 12x12 in. open-top bakelite cell equipped

Jan 1, 1956

I. PRESIDING OFFICER. At all business meetings of the Institute the President, or, in his absence, the First Vice-President, or, in the absence of both of them, any other Vice-President or Director, chosen by the meeting, Shall preside. At all other meetings of the Institute the President, or, in his absence, one of the Vice-presidents, Shall preside. If none of these be present the meeting Shall elect a Chairman. The President Shall do and perform Such other duties as may from time to time be assigned to him by resolution of the Board of Directors of the Institute. IL ORDER OF BUSINESS. At each business meeting of the Institute the order of business Shall be as follows: 1. Reading of minutes of preceding meeting. 2. Report of the President. 3. Report of the Treasurer. 4. Report of the Secretary. 5. Election of Directors. 6. Reports of Standing Committees. 7. Reports of Special Committees. 8. Special Orders. 9. Miscellaneous business. This order of business may be changed at any meeting, by a vote of a majority of the Members and Associates present. At all sessions of the Institute, other than business meetings, the order of proceedings and the time of adjournment Shall rest in the discretion of the presiding officer. III. SECRETARY OF THE INSTITUTE. The Secretary Shall keep a record of the proceedings of all the meetings of the Institute. He Shall be custodian of the corporate Seal, of the minute books and of all the legal documents belonging to the Institute. He Shall have charge on behalf of the Institute of all correspondence. He Shall notify all Officers and Directors and all members of committees of their election and appointment; Shall issue notices of all meetings of the Board, and of the annual and other business meetings of the Institute; and Shall, in calling Special meetings of the Directors, Specify the objects of Such meetings. He Shall act as clerk at all the meetings of the Board of Directors and at all meetings of the Institute. The Secretary Shall be custodian of all technical or Scientific papers Submitted to the Institute for its consideration and Shall have general charge and supervision of the editing and proof-reading of all material published by the Institute, and. of the distribution thereof. The Secretary shall be the custodian of all back numbers of the Transactions and other publications of the Institute. There Shall be kept under his direction an account

Jan 1, 1925

By M. A. Mahtab, J. D. Dixon

The results of a parametric study of the influence of natural features (stress field, rock strength, and strength and orientation of fractures) as well as the influence of induced features (undercut span, boundary slot, and other boundary-weakening measures) on the cavability of an undercut block of ore in mining by the block- caving method are presented. The two-dimensional finite-element analysis technique was used for this study. A coarse "mesh," along with linear homogeneous assumptions for rock properties, was used to model the problem of initiation of caving in a block of ore. Interpretation of the test results suggests that weakening the "abutments" of the block as well as certain orientations of natural fractures exercise significant influence on cavability. These findings hold promise for immediate application to known situations in block-caving mines.

Jan 1, 1977

By R. C. Ku, R. G. Davies

The stress-strain behavior of Fe-C and Fe-Ni solid-solution alloys has been investigated at 25°C. It is found that the rate of solid-solution strengthening is dependent upon the strain at which the yield stress is measured, the macroyield stress being much more concentration-dependent than the microyield stress. In fact the addition of nickel does not lead to any increase in the microyield stress of iron. The primary effect of increasing the carbon or nickel content is to increase the slope of the stress-strain curve in the microyield region; this effect has been correlated, by means of transmission electron microscopy, with a decreased ability of the dislocations to cross-slip. It is concluded that the Mott-Nabarro theory is a good description of true solid-solution hardening in these and other iron-base alloys. A.LL theories of the solid-solution strengthening1-4 indicate that the flow stress of an alloy increases both with solute concentration and "misfit" between the solvent and solute atoms. The functional relationship between strength, solute concentration, C, and misfit depends upon the particular theory. Mott and Nabarro1,2 and Schoeck and Seeger3 both predict a linear increase in strength with concentration, while Fleischer4 indicates that the strength should be proportional to C1/2; there are in the literature experimental observations to support both these compositional dependencies.1'8 The experimental evidence used to support the theories is the change in macroscopic yield stress (strain, e, = 10-3) with composition. However, recent investigations have revealed that solid-solution strengthening in a Cu-Al single crystals7 and in Fe-V polycrystal-line" alloys depends upon the strain at which the flow stress is measured; a flow stress in the microplastic range (e = 10-6 to 10-5) is much less concentration-dependent than the macroyield stress. Since the theories of solid-solution strengthening are concerned in particular with the stress to move a dislocation in a dislocation-free matrix, they should only be compared with microyield-stress data; it will be shown that in a material deforming homogeneously the microyield stress (e = 10-6) is approximately the stress to move through the matrix those dislocations which have been nucleated by stress concentrations such as particles or grain boundary ledges.9-11 In contrast, the macro-yield stress is more complex in that it is affected by several phenomena: dislocation multiplication, dislocation interactions, and the ease of propagating slip across grain boundaries. For example, it is experimentally observed that when long-range order12'13 or solute effects10 restrict cross alip the grain boundary

Jan 1, 1967

By F. M. Lewis, E. C. Johnson

Used as a classifier in a plant expanding capacity or changing to closed-circuit operation, the liquid-solid cyclone offers the advantage of being adaptable to existing conditions. This paper presents the costs involved and experience gained from operating a unit of this kind. BY now application of the liquid-solid cyclone to various classification problems in the chemical and metallurgical fields is more or less familiar. A less publicized application receiving wider consideration as time goes on is its use as a classifier in closed-circuit grinding operations. This paper presents the costs involved and the experience gained from operating a unit of this kind. In May 1951 the Tennessee Copper Co. installed in its London mill at Copperhill, Tenn., a liquid-solid cyclone in closed circuit with a 6x12-ft ball mill. The circuit in which this cyclone is used is the regrind or secondary grinding circuit of a copper flotation plant. Originally it consisted of a 7x1-ft conical ball mill in closed circuit with a bowl classifier. Changes made in the primary grinding circuit of the mill necessitated a regrind circuit of greater capacity. The bulk concentrate to be ground was raised from 900 or 1000 tpd to 1200 or 1300 tpd, and to accommodate this increase a 6x12-ft ball mill which had been in the primary grinding circuit was moved into the regrind circuit. When this was done it was found that the classifier was too small to give efficient operation. Space in the plant was at a premium, and since use of the cyclone offered considerable economy the installation shown in Figs. 1-3 was made. The unit installed is a 24-in. diam cyclone classifier with a 20" cone angle. Diameter of the vortex finder is 8 in., the feed entrance area 20 sq. in. Maximum diameter of the adjustable apex valve is 6 in. and minimum diameter approximately 3.5 in. To refer again to Figs. 1 and 2, the cyclone* is mounted motor. It is charged with 18 tons of 1-in. balls. The overflow, or fines, passes by gravity directly to the copper flotation plant. The ball mill discharge and the new feed combine in a sump from which they are sent to the cone by an 8x6 SRL pump at a rate of 497 gpm. Pressure at the cyclone is 5 psi. For reasons dictated by the nature of the ore treated, particularly the bonding of fine grains of chalcopyrite to pyrrhotite, the froth from the second cell of the copper rougher circuit is returned to the regrind mill. This flow, which somewhat complicates the standard closed-circuit calculation, is seen in Fig. 1 to be 156 tpd of solids. This combines with the cyclone classifier underflow to constitute the ball mill feed. The requirement of the regrind product is that it be 77 to 80 pct —200 mesh. The liquid-solids cyclone operating in conjunction with the 6x12-ft mill adequately met this requirement. Of primary importance is the fact that this arrangement provided sufficient classification capacity to replace the undersized classifier and was capable of building up a circulating load to 87 pct, large enough to give an efficient grind. In this instance the circulating load is taken as the ratio of sands to new feed. Any comparison of performance between this liquid-solid cyclone and the replaced classifier would of course be unfair, since the bowl classifier was

Jan 1, 1955

By AIME

TITANIUM-RICH ilmenite deposits, situated in the Allard Lake area in Quebec some 400 miles down the St. Lawrence River from Quebec City and 28 miles north of Havre St. Pierre on the north shore of the Gulf of St. Lawrence, are undergoing an intensive development program by the joint efforts of the Kennecott Copper Corp. and The New Jersey Zinc Co. Easily accessible ore, amounting to about 125 million long tons and carrying from thirty to forty per cent titanium oxide, has been delimited. Plans are being made for construction of an electric smelter at Sorel, on the south bank of the St. Lawrence midway beween Montreal and Three Rivers, which will produce 650 long tons of high-grade titanium slag and 500 long tons of iron per day from 1500 long tons of ore. Occurrence of ilmenite ore in this area has been known since J. A. Retty reported his geological work in the lower Romaine River area for the Quebec Bureau of Mines in 1941. In this report Dr. Retty mentions the presence of anorthosite rocks, some of which were rich in ilmenite. Claims were staked by several interests but the small showings and complex metallurgy were too formidable for any organization not adequately equipped with capital, metallurgical knowhow, and market outlets. However, Kennecott became interested and through a newly formed Canadian subsidiary, Kennco Explorations Ltd., options were taken up under the direction of A. H. Robertson. An area of 300 square miles was traversed in the summers of 1945 and 1946. During 1946 and 1947 geophysical and diamond-drill prospecting disclosed a num-

Jan 1, 1948

By Philip D. Shelton

INTRODUCTION Traditional design of support for permanent underground mine excavations place great emphasis on the magnitude of the maximum radial load which a specific support or lining must sustain. However, this depends upon so many factors that reliable prediction in advance of excavation is very difficult except in strong-self supporting ground. Some of the factors affecting the loads acting on a support are illustrated in Table 1. [ ]

Jan 1, 1984

By William J. Potter, Roger N. Pyle

Introduction The primary ingredient for survival of mining companies during a recessionary period is to be innovative and resourceful in the structuring and financing of operations. Over the past decade, many mining companies have had to retrench and restructure their operations and to redeploy their assets just to survive. During the same period, traditional sources of financing for mining companies -- commercial banks, subsidized export credit loans and long term straight debt financing in the public markets -- became less available and more expensive. Meanwhile, new markets and new financing instruments provided new alternatives for mining companies. Those companies which exploited these alternatives greatly enhanced their capacity for survival and even for profitability. This article considers the strategies adopted by some companies to adapt to changes in this recessionary environment; the inadequacy of traditional sources of financing; certain of the new financing instruments, structures and markets which have become available; and how several mining companies have utilized these new instruments, structures and financial markets to improve their competitive positions. THE IMPACT OF RECESSION ON MINING COMPANIES AND TRADITIONAL FINANCING SOURCES In its 1983 year-end article "The New Economic Order" Mining Journal characterized many of the large private sector mining companies with operations in the industrialized countries as being "gripped between the jaws of high working costs and stagnating metal commodity prices." The article went on to characterize the Canadian mining industry in particular as being "in the difficult position of having to seek to sell the bulk of its output in a world market characterized by over-capacity, where production costs were determined by internal political and economic factors while prices were set by external competitive forces of supply and demand." Miners of a wide range of commodities in the industrialized countries have come to realize that their domestic mineral resources are in many cases no longer competitive with global sources of supply. To compete and survive they would have to rely on their technical and financial expertise in mineral exploration and development and in mining and processing. Strategies For Survival Global competition has compelled management in the extractive industries to improve their worldwide cost position. This is the only means whereby a mining company can differentiate its product and attain a substantial competitive advantage. During the past decade, for example, ASARCO Inc. and Inco Ltd. chopped their payrolls, postponed expansion plans and otherwise retrenched. ASARCO reduced its capital expenditures and cash requirements for operations in 1984 to a level almost equal to its internally generated cash. The company's finances were also strengthened by increasing total lines of credit from outside sources, by selling common stock, and by reducing annual pension funding through a change in actuarial assumptions. Other companies returned to their traditional organizational structure where they had a demonstrated competitive strength. Consolidated Gold Fields, for instance, resumed its operation as a mining finance house. Its capital investment programs are now devoted solely to resource development. In mid-1984, at a time of firming zinc prices, Union Miniere S.A. used the opportunity to integrate its smelting capacity and to direct investment to certain subsidiaries at the expense of less viable operations. Smaller corporations realized that it was not enough just to be the low-cost producer. For example, Drummond Coal Company in Alabama, which dominates its regional market due to its low-costs, has also developed a world-wide trading capability and has placed incremental tonnage from its own mines as well as brokered coal produced by others, thereby minimizing capital risk. In Canada, Campbell Resources has exploited difficult times by acquiring assets cheaply. In the process it improved its capacity to withstand cyclical economic swings by diversifying from solely a copper and gold producer to a company based upon asbestos, coal, copper, gold and natural gas.

Jan 1, 1985

The Telfer Project, one of the world's newest gold mines, is located about 300 km (190 miles) northeast of the Mt. Newman iron ore project in the northern part of Western Australia. The first mineral claims were staked in 1972; and by mid-1975 ore reserves of 3. 8 million mt (4. 19 million st) of 9.6 g per mt (0. 28 oz per st) ore had been indicated. It is interesting to note that Newmont spent more than 10 years and A$10 million in Australia for extensive mineral exploration before finding the Telfer deposit, and then spent approximately A$3 million in exploration and feasibility engineering on Telfer. Including this A$3 million, a total of A$27 million was spent to complete construction of the mine, village, gold treatment plant and associated roads, airport, water and services. Over 50% of the capital cost is in the metallurgical facility, or approximately A$10, 000 per ton per day. All economically significant gold mineralization at Telfer occurs in a series of layered quartz-limonite reefs in which the former pyrite has been oxidized to limonite to a depth of 100 m (330 ft). The most important gold reef occurs at the base of the siltstone-shale horizon within the enclosing sandstone dome -like structure. At the Main Dome structure the dipping ore horizons will be mined to a vertical depth of about 60 m (200 ft) by open-cut methods. The waste-to-ore ratio is approximately 12:1. Eventually 44 million mt (48. 5 million st) of ore and waste will be mined. Mining of the waste is by contract; however, the ore and a thin layer of waste is company-mined. Dilution from mining the geological ore reserve is about 10%. The ore is completely oxidized and the gold occurs free within the reef, material as discrete particles of varying but mainly fine grain size. Most of the gold is "free milling"; that is, over 50% of the gold is coarse enough to be recoverable by gravity concentration. Two duplex mineral jigs receive the two cyclone underflows from the grinding circuit. The rougher jig concentrate is up-graded on a continuous strake from which the concentrate is tabled to produce a final free gold product. Jig tailings are returned to the ball mill and the concentrates are amalgamated. Gold amalgam is pressed, retorted, and melted into gold bars. The gravity gold recovery circuit is the same as was used in many of the gold mills in California in the 1930s.

Jan 1, 1981

By J. B. Cheatham

The influence of friction on the force required for an idealized bit tooth to penetrate a "plastic" rock is analyzed. The rock is assumed to obey the Coulomb-Mobr yield criterion and the tooth is represented by a two-dimensional sharp wedge. At the tooth-rock interface the stress field not only satisfies the yield condition but also is such that the ratio of the shearing stress to the normal stress is equal to the coefficient of friction. The solution relates the force on the tooth to the depth of penetration, the tooth angle, the coefficient of friction between the rock and bit tooth and the angle of internal friction and compressive strength of the rock. INTRODUCTION Most rocks are brittle at atmospheric pressure but exhibit ductility and increased strength as the confining pressure is increased. In a previous analysisl the force required for a bit tooth to penetrate a rigid-plastic rock was computed for two limiting conditions: (1) a perfectly lubricated tooth-rock interface which should correspond to a lower limit for the penetrating force, and (2) a perfectly rough interface which should provide an upper limit. Experimental results2 for rock indentation under confining pressure have confirmed that the analysis generally predicts upper and lower limits for the penetrating force as a function of rock properties and tooth angle. The present analysis extends the previous work to account for the friction between the rock and the tooth. ANALYSIS The force required for incipient plastic flow of an idealized model of a rock under a bit tooth is computed subjected to the following assumptions. BIT TOOTH 1. sharp two-dimensional wedge (end effects neglected) 2. rigid tooth (elastic deformation of tooth neglected) 3. displacement of tooth is normal to rock surface 4. friction exists between tooth and rock ROCK 1. semi-infinite, isotropic and homogeneous 2. rigid-plastic (elastic deformation of rock neglected) 3. non-work hardening (horizontal stress-strain curve) 4. Coulomb yield condition* (linear Mohr envelope) 5. smooth, flat surface According to the Mohr theory of failure it is assumed that failure occurs when the state of stress is such that the Mohr stress circle becomes tangent to an experimentally determined envelope. The Mohr failure curve is frequent1y approximated by a straight line and referred to as the Coulomb-Mohr failure criterion. If the rock is under sufficient pressure to be ductile we can use the linear envelope as a yield condition. The Coulomb-Mohr yield criterion is illustrated by Fig. 1 and is expressed by the following equation:l

By B. H. Caudle, M. D. Witte

In predicting the performance of a pattern injection operation, the engineer needs to know both the amount of oil to be recovered and the rate at which the recovcry will take place. This paper- describes fluid flow model studies on the effect of mobility ratio on the rate of oil recovery in a five-spot. The results show the change in fluid conductivity (total flow rate/pressure drop) as the sweep-ont pattern increases for mobility ratios between 0.1 (and 10. There data, when cornbitted with a knowledge of reservoir permeabilities and sweep-orit pattern efficiencies, cata he used to predict the cLrmulntivr oil production as a function of time for homogeneous five-spot injection systems. INTRODUCTION The flow potential in a pattern flood element is a function of the mobility ratio and how far the injected flood front has gone.1,2 For a waterflood project having a mobility ratio of one, the conductance—which is the flow rate per unit pressure drop (q/Ap)—-will remain the same throughout the life of the flood. If the mobility ratio is favorable ( < I), the conductance of the project will drop continuously throughout the operation. If, on the other hand, the mobility ratio is unfavorahlc. the conductance ratio will increase continuously. Therefore, if the reservoir engineer wishes to predict either the rate at a specified pressure or the pressure at some rate for a secondary recovery project, he must know how the conductance will vary during the flood. Other investigators have studied this problem using potentiometric models&apos; or analytical solution&apos;. The

By W. C. Knopf, I. M. LeBaron

In the Carlsbad area potash is dry-mined and wet-concentrated. Wet concentration involves recircu-lation of saturated brines, with resultant difficulties of brine disposal and inherent losses in recovery through solution of the KCl. A dry beneficiation process for potash minerals would offer many advantages over present methods. International Minerals & Chemical Corp. has been working on development of a dry process for some time. This article is a progress report. Potash ores available in this country are largely mixtures of halite and sylvite contaminated with slimes and often with many sulfate and magnesium minerals. Electrostatic concentration of KCl when the contaminating minerals are in low percentage has been accomplished. Continuous production of better than 60 pct K2O concentrate from high potassium sulfate ores has not been demonstrated at the present time. Laboratory Procedure: Laboratory work on electrostatic beneficiation of potash minerals has been carried out using both pure crystals and mined ore. Electrostatic separation of the two main components of potash ore, sylvite (KCl) and halite (NaCl), is accomplished by first heat-treating the ore to allow for electric charging of the particles. Preferential exchange of&apos; electrical charges between different mineral particles through surface contact is the principal mechanism involved. After proper conditioning of the particle surfaces, the oppositely charged minerals are dropped vertically into a horizontal electric field having a field gradient from about 5000 to 15,000 v per in. The particles are free-falling in the field. A suitable power supply is used to produce the proper total voltage for the electric field. Total required voltage is, of course, a function of electrode spacing. A typical electrode arrangement with power supply is shown in Fig. 1. In general, the total voltage on any system is 75,000 to 90,000 v. Power consumption is negligible, as leakage at insulators and corona discharge are the main losses in the system. Optimum preheat temperatures for pure material components generally are not the same as for mined minerals. Fig. 2 shows clearly that maximum recovery on a 50 pct pure KCl, 50 pct pure NaCl mixture occurs at a preheat temperature of about 600°F. In this test the preheat mixture was allowed to cool to about 225°F before dropping through the electric field. The optimum temperature for sep- aration is practically never the optimum temperature of preheat. Optimum separation for mined Carlsbad potash ores occurs when a preheat temperature closer to 900°F is used, as shown by Fig. 3, which plots percent sylvite (KCl) in the concentrate and tails as a function of preheat temperatures. Here again the ore was allowed to cool to about 225°F before separation. It should be noted that efficiency of separation increases continuously with increasing preheat temperatures until incipient fusion of the ore takes place at about 950°F. The increase in optimum preheat temperature for Carlsbad ores over the pure minerals can be traced to the effect of the clay slimes intimately associated with the mined potash. If the slimes associated with the ore are removed by washing with alcohol or other non-aqueous material, the necessity of preheating to the high temperature is removed. This temperature range has been proved critical within these limits during continuous pilot plant operation. Concentrate and tailings grade and optimum recovery also are functions of the temperature of the potash mineral particles during separation in the electric field. Fig. 4 presents data indicating that feed to the rougher pass should range between 150°F and 275°F for best results. It has been found by subsequent pilot plant work that these temperatures can be maintained in actual operation.

Jan 1, 1959

By Donald D. Smythe

Tars paper describes briefly the topography and geology of the region where the mica-bearing pegmatites are found and discusses prospecting, the quality of the mica, its preparation, and evaluation of the deposits. Muscovite mica occurs in a number of widely separated localities in Brazil, but production has come largely from deposits in the southeastern and eastern part of the State of Minas Gerais (Fig. I). There the deposits form a discontinuous zone, which starts at a point 90 km. north of the city of Rio de Janeiro and extends north for some 500 km., roughly parallel to the coast. A maximum width of 180 km. is reached along the Rio Doce. To the west in Minas Gerais, and extending east into the states of Espirito Santo and Rio de Janeiro, the mica zone proper is fringed by areas in which there are scattered occurrences of mica-bearing pegmatites. A few of these outlying deposits have produced commercial mica, but most of them are unimportant. To the southwest, in the State of São Paulo, there are a number of mines, which at one time produced a very considerable amount of sheet mica, largely as a by-product of kaolin mining. These deposits, and, a few others lying between them and the main productive areas to the northeast, appear to be the southwestern continuation of the strong Minas Gerais mica zone. In the vicinity of Conquista, just north of the Minas Gerais boundary in the State of Bahia, and still farther north, near Jacobina, there are several known mica deposits. Their location indicates that they may be the northern continuation of the main mica zone. The major part of Brazilian mica production has come from four areas within the mica zone proper; from north to south, Governador Valadares, Raul Soares, Espera Feliz, and Muriaé. The first is 190 km. from north to south and reaches a maximum width of 180 km. The Raul Soares area extends 135 km. from northeast to southwest, and in places is 80 km. wide. The Espera Feliz area is 100 km. from north to south, and reaches a width of 35 km. The Muriaé area extends 150 km. from northeast to southwest and its width reaches 40 kilometers. Between the known productive areas, and in the areas directly to the southwest and to the north of them, little mica has been produced. These gaps, as well as certain irregularities in the outline of the mica zone itself, are to be ascribed either to lack of prospecting or to conditions preventing the discovery of mica, rather than to its nonexistence. Elsewhere in Brazil mica has been reported from eastern Goiaz, Ceará, Pernambuco, Rio Grande do Sul, Matto

Jan 1, 1946

By JAMES A. VEASEY

SINCE the World War, excepting for a few brief periods of relief, the American petroleum industry has been obliged to meet its important economic responsibility to this nation hampered by the maladjustment that inevitably follows a marked and unwholesome over-production of its raw material, crude oil. Despite the warnings of the Federal Oil Conservation Board and the endeavors of many of the leaders in the business to stem the flow of oil from the wells of the country, the evil ,not only persists but, at the moment, seems more malignant than ever before. Unless the local and temporary restraints on drilling and production now in effect in California, Wyoming, Texas, and Oklahoma are continued, and, indeed, unless stricter and more comprehensive measures of the same sort are imposed and adhered to by the industry in those States, over-production in the enterprise during the current year will be more pronounced than in any other period in history.

Jan 1, 1929

By A. A. Jr. Smith, J. S. Smart

The controlled amounts of phosphorus, arsenic, sulphur or selenium found in commercial coppers perform a variety of highly useful functions. Indeed, a large segment of modern copper technology is essentially dependent upon the presence of one or more of these elements. Consequently, the literature contains many references to their effects but the scope is broad and has been only partly covered. New data are presented herewith directed toward a better understanding of the basic behavior of these elements in copper, with particular emphasis on the composition range o to 0.05 per cent. These data are a part of a general program of research on the effects of impurities on the properties of oxygen-bearing and oxygen-free copper, other portions of which have been reported previously. Schematically, the behavior of individual elements is determined from measurements of conductivity and softening temperature,&apos;v2 and the binary alloys employed are synthesized from high-purity copper in order to eliminate interference from the effects of extraneous impurities. Alloys of selected composition were first prepared in the oxygen-free form by continuously casting the melts in the form of %-in. diameter rod. Oxygen was added subsequently to portions of the alloys, either by remelting or by diffusion at 8jo°C. from a surface scale. Test wires wcre drawn one B. and S. number per pass, using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in., and a final cold reduction of 75 per cent to 0.081 in. Oxygen-bearing slugs made by remelting nere hot-rolled to 4ia in.. drawn to 0.162 in., annealed for 30 min. at 6o0°C. and cold-drawn 75 per cent to 0.081 inch. The alloys containing phosphorus, having been compounded very early in the program, were prepared in the form of 3i6-in. rod, and processed to wire with only the last three intermediate anneals listed above, all of these having been conducted in commercial nitrogen. In addition, the conductivity anneals on these alloys were also performed in the same atmosphere, and the small amount of oxygen present as an impurity in the gas resulted in some loss of accuracy at temperatures of 700&apos; to 8o0°C., as will be shown later. Subsequently, the anneals for all oxygen-free alloys were conducted in hydrogen to prevent oxidation, and purified nitrogen was employed only for oxygen-bearing samples. All conductivity anneals wcre of one hour duration followed by a rapid quench in 10 per cent HZSO*. Effect of Phosphorus The widespread use of phosphorus as a deoxidant has resulted in universal appreci-

Jan 1, 1946

By A. A. Jr. Smith, J. S. Smart

The controlled amounts of phosphorus, arsenic, sulphur or selenium found in commercial coppers perform a variety of highly useful functions. Indeed, a large segment of modern copper technology is essentially dependent upon the presence of one or more of these elements. Consequently, the literature contains many references to their effects but the scope is broad and has been only partly covered. New data are presented herewith directed toward a better understanding of the basic behavior of these elements in copper, with particular emphasis on the composition range o to 0.05 per cent. These data are a part of a general program of research on the effects of impurities on the properties of oxygen-bearing and oxygen-free copper, other portions of which have been reported previously. Schematically, the behavior of individual elements is determined from measurements of conductivity and softening temperature,&apos;v2 and the binary alloys employed are synthesized from high-purity copper in order to eliminate interference from the effects of extraneous impurities. Alloys of selected composition were first prepared in the oxygen-free form by continuously casting the melts in the form of %-in. diameter rod. Oxygen was added subsequently to portions of the alloys, either by remelting or by diffusion at 8jo°C. from a surface scale. Test wires wcre drawn one B. and S. number per pass, using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in., and a final cold reduction of 75 per cent to 0.081 in. Oxygen-bearing slugs made by remelting nere hot-rolled to 4ia in.. drawn to 0.162 in., annealed for 30 min. at 6o0°C. and cold-drawn 75 per cent to 0.081 inch. The alloys containing phosphorus, having been compounded very early in the program, were prepared in the form of 3i6-in. rod, and processed to wire with only the last three intermediate anneals listed above, all of these having been conducted in commercial nitrogen. In addition, the conductivity anneals on these alloys were also performed in the same atmosphere, and the small amount of oxygen present as an impurity in the gas resulted in some loss of accuracy at temperatures of 700&apos; to 8o0°C., as will be shown later. Subsequently, the anneals for all oxygen-free alloys were conducted in hydrogen to prevent oxidation, and purified nitrogen was employed only for oxygen-bearing samples. All conductivity anneals wcre of one hour duration followed by a rapid quench in 10 per cent HZSO*. Effect of Phosphorus The widespread use of phosphorus as a deoxidant has resulted in universal appreci-

Jan 1, 1946

By Haakon Styri

In discussion of Dr. Fitterer&apos;s paper on electrolytic separation of slag inclusions, some results from experiments on electrolyzing high-carbon steels at the SKF Research Laboratory were given. l We had been working for a number of years on chemical methods of separating the inclusions but could not find any solvent that would dissolve the steel without attacking some of the inclusions, particularly the sulfides in which we were mostly interested at the time, nor any that would dissolve all sulfide or silica in filings as fine as 300 mesh without attacking the iron. Electrolytic methods had also been tried without any real progress until we learned from the Bureau of Mines about the use of the collodion membrane around the anode. Our early difficulties were to some extent different from those of the Bureau of Mines, perhaps because of experimenting on steels of higher carbon content, but most of our difficulties were of the same nature as those of the Bureau. Formation of large quantities of basic hydroxides was traced to the use of impure and oxidized ferrous sulfate. To protect from oxidation from the atmosphere during electrolysis, after purer chemicals were obtained, a thin layer, 54 in. or less, of molten paraffin was poured over the surface of the cathode liquid, where it solidified. It was found desirable also to hold the cathode chamber slightly acid by initial addition of 0.1 per cent acid (sulfuric or hydrochloric) to prevent precipitation of the hydroxide. This acidity would decrease gradually and the cathode chamber would become neutral before the end of the electrolyzing. The increase in acidity in the anode chamber during our early experiments had appeared to cause attack of the precipitated sulfides in the residue, which originally was analyzed by volumetric method for sulfur, and for this reason a 10 per cent sodium citrate solution was substituted for the sulfate in the anode chamber. With the use of the more reliable Eschka method for sulfur determination (as in coke), there was however no serious attack on the sulfides in the anode chamber with a variety of different liquids, as shown in Tables 2 and 4. The Eschka method gives a higher sulfur value than

Jan 1, 1933

By E. C. Weichel

THERE have been many attempts at permanent roof support in anthracite mines, in some cases brick arches, in others concrete, and also combinations of brick or concrete walls with steel beams. These supposedly permanent roof supports have frequently failed when heavy pressure is brought to bear upon the structure, because they are so rigid that failure occurs because the structure is unable to adjust itself to the increased load. Roof pressure exerts a tremendous weight, and it is at times difficult to find any means of support which is strong enough to bear the entire pressure, unless this supporting structure has in itself the element of some flexibility which will enable the structure to hold the moving mass until it "arches" itself. If the supporting medium has flexibility enough so that it can adjust itself to the heavy initial loads, and so give the overlying material an opportunity to form a self-supporting arch, then such a roof support will be more useful than any rigid roof support. There has recently been introduced into the anthracite region a new form of gangway lining that is flexible enough to slightly adjust itself under heavy pressures, and so give the loosened material which is being supported a chance to form into an "arched" mass. This lining, manufactured under patents granted to Hans Schaefer of Essen, Germany, was introduced in the United States in the summer of 1928, at which time the Amercan licensee, Richard Howells of

Jan 1, 1930

By R. H. Smith, A. C. Polk

The physical properties of the materials are listed, together with a short explanation of how this material binds the sand grains together without materially reducing the effective permeability of the sand. The chemical can be used in wells with bottom-hole temperatures ranging from 105°F to more than 350°F A description of the equipment required and the techniques used for applying these plastics to the wells is included. Introduction Recovering oil and gas from unconsoli-dated sand formations offers one of the most troublesome of all production problems. These sands generally present no particular trouble while drilling is in progress, but after the well has been completed and a pressure differential has been established across the face of the producing zone, the formation begins to L&apos;slough," resulting in "sanding up" of the well. The term "sanding up" means that sufficient volumes of sand have moved into the well bore or casing to cause a serious reduction or complete halt of all flow of oil, water or gas. In rare cases a well may produce only a small amount of sand and still continue to flow or pump, the sand being carried to the surface in the fluid stream. However, in such instances, the result may be a costly repair bill due to the effect of the sand on surface and pumping equipment. The difficulty of producing petroleum from sands that are loosely cemented has long been recognized by petroleum engineers but only within the last few years has any new approach to the problem been undertaken. This involves the use of plastics that are capable of bonding the individual sand grains in place without materially reducing the effective permeability of a formation. The successful application of plastics for the consolidation of poorly cemented sands is relatively recent but now it is widely used in many of the more difficult areas on the Gulf Coast of Texas and Louisiana. This relatively new use of plastics1 in the oil fields has been preceded by much laboratory and field research on the use of various chemicals2,3 for solving numerous well-completion and work-over problems. Plastics now are being used successfully to control gas-oil and water-oil ratios,4&apos;6 in zone isolation, the repair of casing leaks, the elimination of caving in cable-tool drilling wells6&apos;7 and in the setting of linerss and casing.9 Sand-consolidating plastics, however, are basically different from all others in that they must not form an impervious seal. Field Practices The approach to the sanding-up problem usually has been the mechanical obstruction of the movement of the sand grains.

Jan 1, 1947