Search Documents

By J. F. Myers, F. M. Lewis

The selection of the proper type of flotation machine involves the consideration of a wide variety of factors. Under any condition, all types of machines will promote some kind of separation. Obviously, the correct way of deciding which type of machine is best suited for a particular problem would be to set up all types of machines and test them out in a competitive manner, but the vast number of small concentrating plants are unable to make such complete and exhaustive tests. The experience of the authors of this paper indicates that if all the factors involved in any particular problem can be determined, and if all the flotation-machine characteristics are understood, some basis for selection could be arrived at other than actual comparison. This paper is presented to show how the process factors and machine characteristics have been combined at the mills of the Tennessee Copper Co. from studies of several types of flotation machines. At the two mills of the Tennessee Copper Co. in the Ducktown Basin of Tennessee, four distinct flotation separations are made on the complex sulphide ore. Three different concentrates are produced from the ore—in the order of their importance: iron concentrate, copper concentrate, and zinc concentrate. Four different types of flotation machines are used. The selection of these four machines, for the plant operation, was based upon the study and operating experience of the machine units shown in the following list: Fagergren machine; square cell, size 56 inches Fagergren machine; level type, size 56 inches Denver machine; conical disk impeller, size 24 inches Denver machine; receded disk impeller, size 24 inches Minerals Separation Sub-A, size 24 inches Munro-Pearse deep cell, pneumatic Southwestern air machine, Hunt principle To date the study of flotation machines has been confined almost entirely to the rougher circuits. The various cleaning operations, being relatively a much simpler matter, have not been investigated so thoroughly. Table I shows a typical analysis of the two ores as well as of the mineral content.

Jan 1, 1947

By H. F. Hebley

In recent years, especially in the last decade, great interest has been shown and many advances have been made in the preparation and cleaning of coal. In the major coal-producing countries, the percentage of tonnage cleaned has been increasing ever since 1924. As separating media, both liquids and gases are used, these generally being water and air respectively. Some systems, instead of obtaining separation by the velocity of the medium in which the coal is cleaned, depend on the density of water mixed with sand, or coal dust and shale, or with chemicals such as calcium chloride. In studying the results of coal-cleaning equipment, it will be observed that the efficiency of the cleaning apparatus lowers as the size of the coal decreases. This inability to obtain any marked improvement in the fines has been partly responsible for the installation of dedusting equipment, to remove the fine sizes from the raw coal prior to cleaning. When considering the possibility of installing dedusting equipment, many factors must be taken into account. Very often, but not always, both the ash and sulfur content of the coal increase as the coal size decreases. When bituminous coal, containing soft powdery fusain, is subjected to a wet washing process, the porous fines of the fusain remain in the small coal or in the wash water and delay the dewatering of the washed coal and increase the difficulty of clarification in settling tanks or thickeners. When a dedusted coal is cleaned by a wet process, the sludge recovered from the settling tank often runs so high in ash that the sludge can be discarded without further treatment and still the loss is small. Where treatment of the sludge is desired, however, froth flotation may be used to advantage if the size of the feed is below 1/10 in. Dust from the deduster can be treated in a similar manner. Fusain, which is usually found in the fine sizes, has often a much larger ash content than other coal. Illustrative of this condition is a table of ash contents for the various petrographic constituents of Illinois coal (No. 5 bed) as given by Mitchell' (Table 1).

Jan 1, 1934

By AIME AIME

A REGULAR meeting of the Executive Board 'of American Engineering Council was held in the Onondaga Hotel, Syracuse, N.. Y., Feb. 14, 1921, with the president, Herbert Hoover, presiding. Reports of committees were presented and acted upon as follows: ENGINEER ON INTERSTATE COMMERCE COMMISSION The second meeting of the Committee was. called because it was represented to the Committee' on Pro¬cedure that the American Society of Civil Engineers, the American Association of Engineers, and the Ameri¬can Institute of Consulting Engineers were anxious to have President-elect Harding appoint an engineer to fill one of the vacancies on the Interstate Commerce Commission. The representative of The American Society of Civil Engineers agreed to endorse the recom¬mendations- of American Engineering Council, and the Committee on Procedure prepared and sent a letter to the President-elect, a - copy of this letter being sent to each member of the Board. No names were suggested. . The appointment of an engineer on the Interstate Commerce Commission was approved and the Board, after approving the action of the Committee 'on Procedure in writing the President-elect, voted that, if requested, the Committee on Procedure submit a list of not less than six names for the appointment of an engineer on the Interstate. Commerce Commission.

Jan 1, 1921

By T. L. Joseph, G. Bitsianes

The gaseous reduction of dense iron ore is a topochemical process in which reduction takes place at distinct interfaces between solid phases or layers. Under normal conditions, these interfaces remain parallel to the exterior surface of the ore body as they move inward. Certain conditions, such as cracking, high porosity, impurities, entrapped residual oxides, may cause departures from normal topochemical behavior. THE gaseous reduction of dense iron ore proceeds at interfaces between several solid phases or layers.',' Under normal conditions, these interfaces progress inward and remain parallel to the exterior surface of the ore body. This topochemical behavior is clearly illustrated in Fig. 1 which shows partially reduced specimens of natural and synthetic hematite. Using a coordinated sequence of macro, micro, and X-ray examinations, the authors1-'2 found that the number of interfaces and participating phases was in agreement with the Fe-0 system. Above 570°C, reduction of the ore involved a maximum of three common boundaries between four solid phases: iron, wiistite (Fe,O), magnetite (Fe,O,), and hematite (Fe,O,). Below 570°C, reduction proceeded through two interfaces between three phases: iron, magnetite (Fe,O,), and hematite (Fe,O,). The decrease in the number of phases below 570°C was due to the instability of wiistite below this temperature. The sequence of phases was also consistent with the equilibrium requirements. For example, the layers of iron oxides that were formed in topochemical fashion were always orientated in the order of increasing oxygen content. Thus, in Fig. 1 an outer layer of metallic iron is followed in turn by a thick intermediate band of black wiistite, by a thin layer of light magnetite, and finally by a relatively large core of hematite. This arrangement of the oxide layers was due to restrictions in reducing conditions which were imposed by the physical structure of the solid. The highly reducing gas on the outside of the particle gradually lost its reducing power as it penetrated into the specimen. On a macro scale, the layers of the various oxides appeared to be sharply defined and uniform in composition. Microexamination of the sections, however, revealed that the interfaces did possess measurable widths which varied with the porosity and chemical activity of the oxide phase undergoing reduction. For example, Fig. 2 shows three interfaces in a dense hematitic ore which was partially reduced at 850°C. At the iron-wiistite interface where the greatest porosity developed, the reaction proceeded over a zone 25 to 30 microns in width. Toward the interior, the interfaces became progressively narrower until at the magnetite-hematite boundary the reaction zone was about 1 micron wide. In this region the structure was exceedingly dense; the hematite possessing a porosity on the order of 3 pct. A careful micro study across polished layers of the various oxides revealed generally homogenous and single-phase structures. As reported in a previous paper,' the wiistite layer was characterized by an increase in oxygen content with depth of penetration. The topochemical behavior of reduction was studied in six types of ore of different origin, composition, and physical structure. In most cases, reduction proceeded at the boundaries of well defined layers or phases, and this behavior may be regarded as normal for most dense fine grained ores. Deviations from Ideal Topochemical Behavior A number of deviations from the normal topochemical behavior were noted. In these cases, the continuity of the reduction interfaces was disrupted in one of four ways: 1—Cracking of the specimen interrupted the geometric configuration, and the interfacial advance was no longer parallel to the exterior surface. 2—As a result of high porosity, the interfaces were spread over an appreciable distance and all but obliterated. 3—Impurities in the ore promoted a variety of deviations, including cracking. 4—A residual oxide phase was entrapped in the reaction product and left behind the advancing macro interface. Results from Cracking: A crack leading into the interior of an ore specimen presents a path of least resistance for the counter-flow of reducing gases and gaseous reduction products. Higher reducing conditions can be maintained along such cracks and reduction accordingly will propagate well ahead of the normally advancing reduction interfaces. Cracking was caused by a number of factors, one of which was the thermal spalling of impurities in the massive form. A more general type of cracking was due to reduction and was found in all dense varieties of natural and synthetic hematite, particularly in the temperature range of 500" to 700°C. The effect is shown clearly in Fig. 3. In this case, a dense sphere of pure hematite was partially reduced at 650°C for 100 min. The macrosection shows that one large reduction crack had penetrated the specimen and disrupted the normal topochemical advance of the interfaces. The outer layer of iron was only slightly affected but the thin dark layer of wiistite, adjacent to the ferrite, had widened perceptibly as it progressed along the crack. Farther inward, the magnetite layer was greatly disrupted and had penetrated irregularly to form islands of unaltered white hematite. A great deal of internal cracking is evident in the magnetite phase. From a practical point of view, the cracking of dense ores in the blast furnace could lead to desirable as well as undesirable effects. The general result

Jan 1, 1956

By T. Lane Carter

It is a curious fact that while in our Transactions there are papers dealing with mining-districts in all parts of the world, in Europe, Asia, Africa, and Australia, there is not one which describes the mining possibilities of Nicaragua, our near neighbor. To be most interested in distant objects, like the moon, and to neglect what lies at our feet, appears to be a trait of human nature. The neglect of Nicaragua is not confined to the American Institute of Mining Engineers. In no other transactions am I able to find papers dealing with mining in Nicaragua, some parts of which are as much in need of discovery and research as the North Pole. I hope this paper will be the precursor of many others to be printed in our Transaclions, dealing not only with the miniilg possibilities of Nicaragua, but with the whole of Central America, where there are vast areas a,waiting skill and capital for their development. Much of this capital and skill should come from the United States in the future, although it is probable that European capitalists, when they appreciate fully the possibilities, will investigate more and more the mining-resources of Nicaragua and ot'her Central American republics. Fig. 1 is a sketch-map of Nicaragua showing the principal mining-districts. 11. History. Mining in Nicaragua did not begin yesterday. It was commenced by civilized man when the Spanish conquerors pene-' trated into the interior and forced the natives to procure the precious metal for them. It is strange that the Spaniards did not find more gold, and work on a scale as extensive as in Colombia and other parts of South America. Probably in Nicaragua the Indians covered up most of the rich prospects

Jan 1, 1911

President Howe: It is, of course, not easy to discuss off-hand the paper which Mr. Becker has presented with so much lucidity. I will only make one remark, which is outside of the line of his argument, and concerns merely a passing allusion in his paper. Mr. Becker speaks of the fact that glass breaks with a flat or conchoidal fracture, and that steel shows a rough or " cupped " surface of frac-

Jan 1, 1895

By Cyril Stanley Smith

For many years sulphur and its congeners selenium and tellurium have been regarded as very harmful elements in copper and copper-rich alloys. Like many similar prejudices, this has been found to be partly wrong. All three of these elements actually have no great effect on the working properties of copper and its alloys, and are desirable additions in that they considerably enhance the machinability of alloys in which they are present. Because of their possible commercial importance, a study of the machinability and other properties of the pure binary alloys was made, as described in this paper, and the effect of selenium on a large number of copper alloys was determined. The current opinion regarding the deleterious effects of elements in this group undoubtedly arose because of occasional failures of tough-pitch copper containing unusually high tellurium, and because of the well-known fact that sulphur causes spewing and unsoundness in tough-pitch copper. Siebe,1 also Deretchey and Margolina,2 studied the effect of sulphur on copper and showed that in the absence of oxygen it was present in the form of copper sulphide, which was less harmful to the properties than an equivalent amount of copper oxide. No data have been published on selenium and tellurium, although the statement is often made, following Eggleston,3 that tellurium makes copper hot-short. Copper specifications call for only traces of these elements. Skowronski and Mosher4 give data on the effect of selenium and tellurium on the conductivity of tough-pitch copper. In private communication Mr. Skowronski says that the samples were hot-forged from small castings and drawn to 0.081 in. diameter, but it should not be inferred from this that these elements are harmless to the working properties of wirebars and commercial shapes. Constitution and Microstructure Constitution.—Sulphur, selenium and tellurium exist in their alloys with copper in the form of copper sulphide, selenide or telluride. These compounds are practically insoluble in the solid state and possess limited

Jan 1, 1938

By Cyril Stanley Smith

For many years sulphur and its congeners selenium and tellurium have been regarded as very harmful elements in copper and copper-rich alloys. Like many similar prejudices, this has been found to be partly wrong. All three of these elements actually have no great effect on the working properties of copper and its alloys, and are desirable additions in that they considerably enhance the machinability of alloys in which they are present. Because of their possible commercial importance, a study of the machinability and other properties of the pure binary alloys was made, as described in this paper, and the effect of selenium on a large number of copper alloys was determined. The current opinion regarding the deleterious effects of elements in this group undoubtedly arose because of occasional failures of tough-pitch copper containing unusually high tellurium, and because of the well-known fact that sulphur causes spewing and unsoundness in tough-pitch copper. Siebe,1 also Deretchey and Margolina,2 studied the effect of sulphur on copper and showed that in the absence of oxygen it was present in the form of copper sulphide, which was less harmful to the properties than an equivalent amount of copper oxide. No data have been published on selenium and tellurium, although the statement is often made, following Eggleston,3 that tellurium makes copper hot-short. Copper specifications call for only traces of these elements. Skowronski and Mosher4 give data on the effect of selenium and tellurium on the conductivity of tough-pitch copper. In private communication Mr. Skowronski says that the samples were hot-forged from small castings and drawn to 0.081 in. diameter, but it should not be inferred from this that these elements are harmless to the working properties of wirebars and commercial shapes. Constitution and Microstructure Constitution.—Sulphur, selenium and tellurium exist in their alloys with copper in the form of copper sulphide, selenide or telluride. These compounds are practically insoluble in the solid state and possess limited

Jan 1, 1938

By Alden Greninger

THE time-honored description of the growth of metal crystals to form polycrystalline aggregates is one in which two important steps are con-sidered: (1) nucleation, and (2) dendritic growth, each dendrite starting from its individual nucleus and resulting (upon slow cooling, assuming no solid phase changes) in a macrograin. This picture of the process of crystallization is incomplete, and it is with the hope of enlarging upon it that the following summary and correlation of experimental results are given. MOSAIC STRUCTURE For an exact definition of the mosaic structure of metal crystals-if, indeed, one can be found that will hold for all metals-one must await the results of much experimental work in this field. The writer's investiga-tions have been confined almost entirely to copper and a few of its alloys. The following terms are proposed, and will be used in this report: Macromosaic Structure l.-Large-scale mosaic structure; more specif-ically, mosaic structure of a scale large enough to produce splitting of Laue spots on back-reflection Laue X-ray patterns2. The deviation from exact parallelism of neighboring macromosaics varies from a few

Jan 1, 1935

A. K. McCosh, Coatbridge, Scotland (written discussion*).-It is well known in Great Britain that oven operators in the United States have been able to reduce the coking time much below European standards by the employment of higher temperatures. Our linings have always been the factor that has prevented our doing the same, and it would be of much interest to coke-oven operators here if Mr. Blauvelt would give a typical analysis of the bricks his company uses for the linings of its ovens, and if he could see his way to send me a sample so that I could have the texture examined, I should personally be very much obliged. The lining brick which my company has found most successful is of a ganister variety, and has the following analysis: Silica, 80.8 per cent.; alumina and iron oxide, .17.8 per cent.; lime, 0.8 per cent.; magnesia, 0.07 per cent.; but with this brick the least carelessness on the gas regulator's part may destroy the lining. It would also be of interest if Mr. Blauvelt could give the temperatures of the air leaving these generators and also of the oven flues.

Jan 10, 1918

By Klaus Schwerdtfeger

In order to test the performance of ZrO, (CaO) and Tho,(Yz03) electrolytes in the electrochemical determination of oxygen activities in liquid metals at steel-rrzakitng temperatures , electromotive force measurements have been made with the following cells: The oxygen-- activities are calculated from the electmrnotive forces for the investigated systems. The standard free energy of- formation of MnO and the activity of manganese in Fe-Mn melts are derived. Indications are that the Zr 0z(Ca0) electrolyte exhibits little electronic conductivity at oxygen pressures as low as 10'a atnz at 1600°C; however, the partial electronic conductivity may become noticeable at lower oxygen activities. The Tho,(Yz03) electrolyte is found to be an ionic conductor at the oxygen pressure as low as that for the Mn + MnO equilibrium, but exhibits partial electronic conductivity at oxygen pressures higher than 10"1 atm (1500°C). fi. better control of oxidation and deoxidation reactions in steelmaking may be facilitated if the oxygen activity in the steel is known during various stages of the process. In the present work oxygen activities have been measured in liquid iron, manganese, and iron alloys with galvanic cells using ZrOz(CaO) and s solid electrolytes with the object of establishing the range of oxygen pressure in which these materials can be used as electrolytes at steelmaking temperatures. Calcia-stabilized zirconia and Tho2-Y203 solid solutions are oxygen ion conductors. Such electrolytes were first used by Kiukkola and Wagner1 and Peters and ~ann' in galvanic cells for the determination of thermodynamicquantities of oxide systems in the temperature range 700" to 1200°C. At these moderate temperatures calcia-stabilized zirconia has been found to exhibit predominantly ionic conductivity at oxygen pressures as low as those for the Cr + Crz03 equilibrium,394 but at lower oxygen pressures elec- tronic contribution to conductivity becomes significants4 The Th02-Y203 solid solutions are ionic conductors at oxygen pressures lower than those applicable to zirconia base electrolytes.5'6 At high oxygen pressures Thoz base electrolytes exhibit significant p-type semiconduction. At the time the present experiments were carried out several papers1'-* were published on the electrochemical determination of oxygen activities in liquid iron using the ZrOz(CaO) electrolyte. The results of different authors do not agree well. For instance, according to Fischer and ~ckermann" stabilized zirconia can be used to measure oxygen contents in liquid iron larger than 0.02 wt pct, but according to Baker and west1' ZrOz(CaO) cannot be used for the determination of oxygen content in liquid iron because of high electronic contribution to the conductivity. Fig. 1 is a schematic diagram of the apparatus used. About 500 g of liquid metal is contained in a crucible into which a stabilized zirconia or Th02(Y203) tube is immersed. A platinum contact wire is pressed (with a spring mechanism) against the inside bottom wall of the electrolyte tube. The tube is flushed continuously with a stream of air, CO-CO, (or Hz-C02) (at 0.96 atm and at a rate of about 300 cu cm per min), via an alumina tube inserted inside the electrolyte tube. This alumina tube also contains the Pt-Pt/10 pct Rh thermocouple. A capillary alumina tube shielding the other contact wire is immersed in the melt. The molybdenum contact wires were used mostly; in some cases platinum wire was employed. Molybdenum has the advantage that it dissolves more slowly in the melt than platinum. The whole cell was contained in the alumina reaction tube of a resistance furnace with molybdenum winding. The reaction tube was closed gas tight at both ends and flushed continuously with argon. Because of the poor thermal shock resistance of the electrolyte tubes the cell had to be assembled in the cold furnace. The electrolyte tube and alumina sheath

Jan 1, 1968

By F. H. Kihlstedt

The Larap iron deposits, 125 miles east of Manila, are the biggest high-grade iron deposits in the Philippines, and have in seven years produced nearly 4 million tons of 60 per cent ore. Magnetic surveying followed by churn and diamond drilling cheaply developed a score of million tons. The ore zone is a wedge of metamorphic rocks in fresh, Miocene sediments overlain by agglomerates, which seem to have filled a river valley eroded in the sediments. A mild overthrust of the competent agglomerates crumbled the shale in front. Solutions gradually turned it into more competent hornfels and deposited pyrite, then magnetite and pyrite in the pores. As the temperature rose large bodies of magnetite with some pyrite were deposited by replacement and in open cavities in tensional areas of overthrust shears. At still higher temperature magnetite and calcium-magnesium silicates formed other bodies in similar cavities, and finally the thrust zone was invaded by syenite porphyry, causing high-temperature alteration products. Possibly, as temperature abated, more high-grade ore was deposited. The complicated faulting indicates dynamic, chronological and spatial changes of mineralization rather than zoning in a static system. Noncommercial copper, molybdenum and some gold accompanied the iron mineralization. In the thirties the Philippines gained a justified reputation as a country of considerable mineral wealth. Traces of Chinese workings show that these earliest travelers and traders had in a small way exploited the latent gold resources in the Islands. The Spaniards continued this for centuries, but did not succeed in establishing any steady mining industry. Modern technology was required to get it started. The rapid development in the last decade before the war got its impetus from several financial factors, the return to sugar growers of previously collected taxes, the influx of Spanish capital during the civil war in Spain, the influx of Chinese capital when the Japanese started their "China incident," and others. Directly or indirectly much of this capital reached the mining industry; in particular, gold mining. Out of the turmoil of an exceptional mining boom emerged a sufficient number of good and well managed gold properties to send the production to a level above that of any single state in the United States at the time. Other ore deposits besides those of gold also received their share, and for a country without any heavy industries at

Jan 1, 1949

By F. H. Kihlstedt

The Larap iron deposits, 125 miles east of Manila, are the biggest high-grade iron deposits in the Philippines, and have in seven years produced nearly 4 million tons of 60 per cent ore. Magnetic surveying followed by churn and diamond drilling cheaply developed a score of million tons. The ore zone is a wedge of metamorphic rocks in fresh, Miocene sediments overlain by agglomerates, which seem to have filled a river valley eroded in the sediments. A mild overthrust of the competent agglomerates crumbled the shale in front. Solutions gradually turned it into more competent hornfels and deposited pyrite, then magnetite and pyrite in the pores. As the temperature rose large bodies of magnetite with some pyrite were deposited by replacement and in open cavities in tensional areas of overthrust shears. At still higher temperature magnetite and calcium-magnesium silicates formed other bodies in similar cavities, and finally the thrust zone was invaded by syenite porphyry, causing high-temperature alteration products. Possibly, as temperature abated, more high-grade ore was deposited. The complicated faulting indicates dynamic, chronological and spatial changes of mineralization rather than zoning in a static system. Noncommercial copper, molybdenum and some gold accompanied the iron mineralization. In the thirties the Philippines gained a justified reputation as a country of considerable mineral wealth. Traces of Chinese workings show that these earliest travelers and traders had in a small way exploited the latent gold resources in the Islands. The Spaniards continued this for centuries, but did not succeed in establishing any steady mining industry. Modern technology was required to get it started. The rapid development in the last decade before the war got its impetus from several financial factors, the return to sugar growers of previously collected taxes, the influx of Spanish capital during the civil war in Spain, the influx of Chinese capital when the Japanese started their "China incident," and others. Directly or indirectly much of this capital reached the mining industry; in particular, gold mining. Out of the turmoil of an exceptional mining boom emerged a sufficient number of good and well managed gold properties to send the production to a level above that of any single state in the United States at the time. Other ore deposits besides those of gold also received their share, and for a country without any heavy industries at

Jan 1, 1949

By R. V. Higgins

This paper presents a computer method to obtain the shape factors and equal cell volumes of the channels for any well spacing pattern from a potentiometric model. By using this program the authors have processed the data for the seven-spot, direct line-drive and the staggered line-drive patterns. The data for the five-spot pattern had been previously processed by a noncomputer method and are included for completeness. The shape factors and volumes for the channels are presented in tables for those who want to use them to process data using their own permeability relationships and viscosities of their reservoir oils. The authors have used the data and sets of representative permeability curves to process sample calculationr of waterflood performances. The comparison of the calculated results shows that the influence of well spacing is small. The permeabilities of the reservoir rock to oil and water had a greater influence on oil recovery for a given pore-volume throughput of water than the well spacing pattern. The more water-wet the reservoir rock, the better the possibility of permeabilities which are conducive to good recovery. The viscosity of the reservoir oil also influences the recovery more than the well spacing pattern. The reduction in the percentage recovery of oil with increase in viscosity of the reservoir oils is small when oil viscosities are in the range of 0.1 to 3. Above this range the reductions in recoveries are extensive. Sample comparisons of the time required for different patterns to recover the oil are presented. Results of an example calculation are given to show the effect of the permeability profile on recovery. INTRODUCTION The effect of well spacing pattern on the recovery of oil when flooding with either gas or water has been studied by many investigators. Muskat et al.1 presented an analysis using conductivity, sweep efficiency and unit mobility to the time of breakthrough. Dyes et al.2 used experimental techniques (X-ray shadowgraphs) and different mobility ratios. They presented quantitatively the relationship between mobility and sweep efficiency at and after breakthrough. Hauber3 presented a method to predict waterflood performance for arbitrary well spacing patterns and mobility ratios. Craig et al.,4 using techniques similar to Dyes et al. to determine sweep efficiency for a five-spot pattern, added the use of relative permeability curves at breakthrough and thereafter. Douglas et al.5 sed rela- tive permeabilities and continuously changing saturations throughout the entire five-spot flood pattern. In obtaining their solutions they used finite-difierence equations. Hig-gins and Leighton6,7 also used relative permeabilities and continuously changing saturations throughout the pattern before and after breakthrough. They employed techniques that process a flood-pattern calculation on the computer in about one minute. The methods of Douglas et al. and Higgins and Leighton both checked closely the laboratory results for a wide range of mobility ratios. This paper presents some sample performances calculated by the Higgins and Leighton method that show the effect on recovery of different permeabilities and viscosities using the seven-spot, the line-drive and the staggered line-drive, as well as the fivespot flood pattern. No previous paper has presented these data using different permeability curves and continuously changing saturations throughout the flood patterns. The paper also presents (1) the results and analyses of the flood-pattern prediction, (2) the computer techniques for determining the shape factors and volumes from the potentiometric models for the foregoing flood patterns, and (3) the shape factors and volumes of the channels of the flood pattern in the event reservoir engineers may like to process waterflood calculations using their own permeability curves and reservoir oils. DESCRIPTION OF METHOD VOLUMES AND SHAPE FACTORS The use of channels taken from a potentiometric model (see Fig. 1) to aid in calculating the performances of water floods of nonlinear patterns has been thoroughly explained in the literature.0,7 Therefore, very little theory, discussion, or proof regarding this phase will be repeated in this paper. The computer method presented in this paper to calculate the volumes and the shape factors of the channels of potentiometric models employs the trapezoidal rule for the volumes and the Pythagorean theorem (the hypotenuse equals the square root of the sum of the squares of the two sides of a right triangle) for the shape factors. In calculating the volume of a channel, the area of each cell in the channel is determined and then multiplied by the thickness to obtain the volume. In determining the areas of the cells, trapezoids are constructed whose vertical sides are spaced Ax apart, as shown in Fig. 2. The length of the sides is the difference between an ordinate cut off by the top and bottom of the cell — usually equipo-tentials. The coordinates of the points along an equipo-tential or streamline are obtained by Lagrange's8 equation of interpolation for which the constants are coordinate points at the intersections. Three intersections for con-

Jan 1, 1965

By H. B. FERNALD

THE first year to which the Revenue Act of 1936 has applied is now passed. It is appropriate to try to give some calm thought to the plan of Federal income taxation as now imposed and what it will mean to the business and industry of the country if this plan of taxation is continued unchanged. Whether or not we like to pay these taxes is beside the point. Taxes are high and may be expected to be high for many years. The important question is whether the taxes to be imposed will destroy or injure business enterprise and development, and, in so doing, lower the standards of employment, living, comfort, and welfare of our people. The power to tax is the power to destroy. That destruction may come suddenly as a cyclone, or slowly as dry rot. What, if any, features are there in the present plan of Federal income taxation that have these destructive tendencies? A few of the points follow that seem to call for consideration.

Jan 1, 1937

By K. A. SPENCER

THE production of soft coal from strip mines in the United States has shown a remarkable growth in the last sixteen years, increasing from one and one-quarter million tons in 1914 to approximately twenty-two million tons in 1929. This is a growth of approximately 1660 p& cent, as compared with a growth of approximately 20 per cent in the underground mines for the same period. But even with this marked in- crease the total tonnage produced by open-face mining represents only 4 per cent of the nation's soft coal tonnage.

Jan 1, 1931

By R. W. Diamond

Low-grade ores can be designated by two main classifications: (1) simple low-grade ores, and (2) complex low-grade ores. As a rule the first type has a relatively small metal content, although low- grade iron ores contain a rather high percentage of metal. As the simple type is the one that is ordinarily in mind when the term "low-grade ore" is used, the paper will be devoted mainly to ores in this general category. Cheap treatment is the prime requirement in utilizing low-grade ores of the simple type, although in some cases the value of nonmetallic by-products, such as limestone for fer- tilizer and silica for flux, allows a little more lati- tude than in the usual situation. When the costs are divided under the three headings-mining, milling, and smelting-it is apparent that the last group will not constitute an important factor as a rule because the high concentrating ratio makes the smelting cost per ton of ore fairly low.

Jan 1, 1949

By J. L. Jernegan

IN a former paper laid before the Institute, entitled Lead and Silver Smelting in Chicago, I endeavored to give a description of the manner in which argentiferous lead ores from the far West were treated in that city, and also described the method employed in the desilverization of the silver-lead produced from the ores. It will perhaps be remembered, that very siliceous ores, principally from the Emma mine, Utah, containing over 40 per cent. of silicic acid, were then being treated at the works of the Chicago Silver Smelting and Refining Company in the reverberatory furnace, with the use of metallic iron, in the form of borings, as a precipitating medium for the lead ; and that the extraction of the silver from the resulting bullion was effected by the Balbach process. The Swansea Works, also the works at Brighton, just outside of this city, and those of S. P. Lunt, were at that time treating ore of a similar character by the same method. The inadequacy of the process for the ores then under treatment was, in a manner, pointed out by me in the paper above referred to. Since the time of its writing, many and important improvements have been made in the metallurgical treatment of Western ores in Chicago. Most ores are now roasted previous to reduction, and the latter operation is conducted in the shaft-furnace instead of the reverberatory. Such is the fact at least at the Swansea Works, the largest in the city, and here it was where the first steps were taken in this direction. In selecting these works as the subject of this paper, I am in hopes that the description given of the various metallurgical operations, as they are there now conducted, will serve to give an idea of the improvements introduced

Jan 1, 1876

By James M. Stapleton

It has long been recognized by blastfurnace men that correct top distribution of materials is very important in efficient and economical furnace operation. Thousands of experiments on top design, filling, sizing, and other operations have been carried out to improving furnace performance by securing uniform distribution. Many of these experiments have worked out satisfactorily and have been passed along to the industry. Many of them have been discarded and forgotten. It has been the custom to judge the results of such experimentation by the results shown in improved or lowered furnace efficiency. While the effect on furnace practice will have to continue to be the final criterion of experimental changes, it has always been a desire of blast-furnace men to ascertain the reason for failure or success. Efficiency in the blast furnace approaching the maximum can be measured in several ways: (1) by actual operating results as revealed in the coke rate and tonnage figures, and (2), in the degree to which the top gas approaches the limiting ratio of CO/CO2 for the reduction of iron oxide by CO gas. This ratio is shown in the equilibrium curve in Fig. I for the system Fe-O-C and CO2-CO-C. The closer the top gases approach this limiting ratio (set at 1.08 by Martin1 because of the effect of limestone calcination) the more efficiently we may expect a furnace to operate. The fact that low CO/CO2 ratios parallel eficient operating performance caused us to investigate the cause of good or poor distribution and the effect of filling and other changes on furnace operation. Heretofore it has been possible to take a sample of furnace gas (usually from the dust catcher) and from it determine how closely the reducing gases were to the ideal or limiting value as set by the equilibrium diagram. However, to find just where in the top area the distribution was distorted and the top-gas CO/CO2 ratios were distant from equilibrium values has been a difficult and expensive investigational procedure. In an effort to overcome this difficulty, apparatus was designed to take gas samples and temperatures across the top radius of the furnace. It was hoped that with the aid of this apparatus traverse sampling of the ascending gases could be simplified, and the cost of sampling substantially lowered. Routine experimenting could then be maintained and results checked with furnace operation. It must be emphasized that a traverse sampling is necessary for a true picture, as single samples at any one point are unreliable. This statement can be verified by an examination of Tables 3 to 6, showing results obtained at our furnaces in a large number of tests. Apparatus The design of the equipment for taking the samples was governed by the need for providing a simple, routine test that could be performed fairly quickly without adversely affecting normal furnace operation.

Jan 1, 1943

By James M. Stapleton

It has long been recognized by blastfurnace men that correct top distribution of materials is very important in efficient and economical furnace operation. Thousands of experiments on top design, filling, sizing, and other operations have been carried out to improving furnace performance by securing uniform distribution. Many of these experiments have worked out satisfactorily and have been passed along to the industry. Many of them have been discarded and forgotten. It has been the custom to judge the results of such experimentation by the results shown in improved or lowered furnace efficiency. While the effect on furnace practice will have to continue to be the final criterion of experimental changes, it has always been a desire of blast-furnace men to ascertain the reason for failure or success. Efficiency in the blast furnace approaching the maximum can be measured in several ways: (1) by actual operating results as revealed in the coke rate and tonnage figures, and (2), in the degree to which the top gas approaches the limiting ratio of CO/CO2 for the reduction of iron oxide by CO gas. This ratio is shown in the equilibrium curve in Fig. I for the system Fe-O-C and CO2-CO-C. The closer the top gases approach this limiting ratio (set at 1.08 by Martin1 because of the effect of limestone calcination) the more efficiently we may expect a furnace to operate. The fact that low CO/CO2 ratios parallel eficient operating performance caused us to investigate the cause of good or poor distribution and the effect of filling and other changes on furnace operation. Heretofore it has been possible to take a sample of furnace gas (usually from the dust catcher) and from it determine how closely the reducing gases were to the ideal or limiting value as set by the equilibrium diagram. However, to find just where in the top area the distribution was distorted and the top-gas CO/CO2 ratios were distant from equilibrium values has been a difficult and expensive investigational procedure. In an effort to overcome this difficulty, apparatus was designed to take gas samples and temperatures across the top radius of the furnace. It was hoped that with the aid of this apparatus traverse sampling of the ascending gases could be simplified, and the cost of sampling substantially lowered. Routine experimenting could then be maintained and results checked with furnace operation. It must be emphasized that a traverse sampling is necessary for a true picture, as single samples at any one point are unreliable. This statement can be verified by an examination of Tables 3 to 6, showing results obtained at our furnaces in a large number of tests. Apparatus The design of the equipment for taking the samples was governed by the need for providing a simple, routine test that could be performed fairly quickly without adversely affecting normal furnace operation.

Jan 1, 1943