Search Documents

By P. J. Jorgensen, J. H. Westbrook

The anomalous indentation creep of nonmetallic solids is shown to be due to the presence of adsorbed water. Although a specific mechanism is not proposed, it is suggested that the water may be present in two chemically adsorbed states. DEPENDENCE of the indentation hardness of solids on the time of load application was first studied systematically by Hargreaves1 in a study of lead and certain low-melting alloys. This technique has become known as indentation creep and has been exploited particularly by underwood and by Mulhearn and Tabor3 as well as by others.4°7 For metals good correlations have been found between the time dependence of hardness over several orders of magnitude in the seconds range and creep parameters from conventional tests at the same temperature where creep strains were measured over hundreds or thousands of hours. However, Walker and Demer8 and Mitsche and Onitsch9 observed extensive indentation creep at room temperature (particularly for light loads) in certain minerals and in materials such as lithium fluoride and magnesium oxide for which conventional creep is ordinarily not observable unless the testing temperature is at a very much higher fraction of the melting point. Normal behavior was observed' for metals such as copper, i.e., negligible time-dependent flow during room-temperature indentation. Walker and Demer attempted to find some distinctive difference in the surface deformation markings about indentations in the anomalously behaving materials at short and very long indentation times. No significant differences were observed. Increased duration of loading was found, however, to result in an increase in the length of glide of edge-dislocation loops extending into the interior of the crystal. Jorgensen and Westbrook,10 in a recent study of

Jan 1, 1965

By H. F. Johnson, C. S. Harloff

The Nichols series system of electrolytic copper refining has successfully maintained its strong competitive position in the copper-refining industry of today; therefore the improvements made in accomplishing this result are of interest. While additional interest would lie in specific comparisons of results obtained in series operation with those in multiple, we have refrained from such a comparison because it can be fair to both only when they are operating under similar conditions on the same grade of materials. Historical The Nichols Copper Co. started a small refinery at Laurel Hill, using its present system, about 1892. The details of the process in its early stage of development were kept strictly secret, so that no information was published or interchange of ideas permitted with the staffs of other copper refineries, where the multiple system was being developed at the same time. However, the fundamentals of the process and type of cell used today differ very little from their earliest form. All operations including loading and unloading of tanks, and all transportation as well, were carried on by hand. The plant remained in this condition with a gradual expansion taking place until the World War forced such a rapid development that little time or thought could be devoted to modernization or mechanical improvement requiring careful design or detailed planning. Considerable progress was made, however. (1) Large refining furnaces were developed. (2) The old expensive air-lift type of circulation was abandoned in favor of the present system. (3) Operating technique was gradually developed to a high point of efficiency. (4) Tank construction and lining were greatly improved, the first concrete tank being installed in 1915. (This tank is still in operating condition.) (5) A new power plant was constructed. (6) Fuel oil was substituted for lump coal on the refining furnaces. (7) Mechanical casting of the finished product was accomplished. During this entire period the plant was particularly fortunate in receiving only high-grade, clean copper bullion coming principally from the Phelps Dodge mines in Arizona. This, together with the lack of

Jan 1, 1934

By Paul D. Conatore

INTRODUCTION There are important reasons for a discussion of tungsten resources, reserves, and production in the Circum-Pacific area. First, the world's chief tungsten deposits, as well as most of the world's tungsten reserves and production, occur in this region. It is well known that the world's largest tungsten reserves are located in southeastern China and that for many years, the largest individual mine in the world was there. Although China still has the world's greatest tungsten production, the very high-grade scheelite mine of Canada Tungsten Mining Corporation in the Northwest Territories is the largest producer of tungsten today. There is certainly a great quantity of tungsten in Asia, but the strategic importance of this fact is now offset by the wide distribution of mines and production facilities throughout the world, especially in other parts of the Circum-Pacific area such as Australia, Canada, and the United States. In addition, much of the Circum-Pacific area is comprised of Mesozoic-Cenozoic orogenic belts. These global tectonic units are regarded as very favorable for additional tungsten deposits, particularly scheelite-bearing tactites, and consequently, prospecting and exploration will most likely be concentrated in the Circum-Pacific area. Second, tungsten must be regarded as one of the, most important metals of modern industry because of its very special properties. It has the highest melting point, the highest tensile strength at elevated temperatures, and the smallest compressibility of any metal. The metal also possesses a very high density, excellent corrosion resistance, good thermal and electrical conductivity, and a low coefficient of expansion. As a result, tungsten has found increasing importance in a wide range of industries. From the filament in an electric lamp, to cutting tools and drilling bits, to the exotic radiation shields that protect supersonic aircraft and spacecraft, tungsten plays an indispensable role in our daily lives. The primary objective of this paper is to present an overview of important facets of known and suspected tungsten in the Circum-Pacific area. Resources, reserves, current production, planned capacity expansions, and new operations, as well as an assessment of the probability for development of deposits in the Circum-Pacific area, are discussed. RESOURCES The average crustal abundance of tungsten has been estimated at 0.0015 kilograms per tonne. A comparison of the abundance of various metals in crustal rocks to that of tungsten is presented in Table 1, which shows that tungsten abundance is similar to that of its commonly associated metals, tin and molybdenum. Table 1. AVERAGE CRUSTAL ABUNDANCE OF VARIOUS METALS (Grams per Tonne) [ ] With careful thought, it can be realized that tungsten ore deposits result from the concentration of the metal, through normal geologic processes, to levels substantially greater than its average crustal abundance. The minimum technologically and economically workable tungsten concentration, or cutoff grade, is a function of (1) deposit tonnage, (2) mining and milling methods, (3) production tonnage, (4) capital and operating costs, (5) tungsten market conditions, and (6) value of associated recoverable metals. The tungsten cutoff grade that is currently exploitable at a profit varies from 0.09% W03 to 1.55% W03, reflecting concentration factors from 470 to 8200, as shown in Table 2. Table 2. CURRENT TUNGSTEN CUTOFF GRADES [ ]

Jan 1, 1982

By D. G. Westlake

Alloys of poly crystalline Nb-H have been tensile tested at 77" and 120°K after slow-cooling and after quenching from room temperature. A rationale has been developed to explain the effect of cooling rate on ductility in terms of microstructure. The inferior ductility of the slow-cooled alloys in this temperature range can be attributed to the precipitation of coarse hydride particles that fracture in the early stages of plastic deformation. Quenching Produced much smaller hydride particles and a decreased tendency for initia-tion and popagation of cracks. Prismatic dislocation loops, punched into the matrix of quenched alloys, eliminate the yield point and may Play some role in the low temperature ductility of the quenched alloys. The difference in ductility between quenched and slow-cooled V-H alloys was even greater than that observed in the N b-H alloys. It is well known that the ductility of Nb-H and V-H alloys decreases with increasing hydrogen concentra-tion and with decreasing temperature.1-l1 The follow-ing are some of the numerous mechanisms that have been adopted in attempts to explain these observations: 1) hydrogen-dislocation interarction,4'6 2) lowering of the crack surface energy by adsorbed hydrogen,9'10 3) localized lowering of the niobium bond strength,9 and 4) exertion of pressure inside voids by molecular hydrogen.6 A recent study1' indicates that, in some way, the embrittlement is related to the precipitation of a hydrogen-rich phase, because embrittlement and hydrogen solubility have the same temperature dependence. Most of the investigators observed that at very low temperatures there was a return of the ductility. Thus, hydrogenated niobium and vanadium may be said to exhibit a low temperature ductility minimum."1'8'9 It has been reasoned by most observers that diffusion is required for the embrittlement mechanism to be operative, and that as hydrogen becomes immobile at very low temperatures, the ductility increases. This investigation of the mechanical behavior of Nb-H al-loys under various conditions is an attempt to gain a better understanding of the low temperature ductility minimum. EXPERIMENTAL Tensile specimens, with gage length dimensions 20 by 3 mm, were machined from sheet stock" and both faces were ground on wet 600 grit Sic paper to obtain a final thickness of 0.5 mm. Annealing as described earlier12 resulted in average grain diameters of 0.3 mm. The recrystallized niobium tensile specimens were electropolished in 90 parts H2S04, 10 parts HF (48.9 pct) by volume, at 287°K and 30 v. Hydrogen, which may have been present in the starting material and/or added during specimen preparation, was removed by annealing at 1073°K in a dynamic vacuum of 2 X 10-6 torr. Hydrogenated specimens (1.15 at. pct H) were prepared by reaction with a known quantity of pure hydrogen (obtained by thermal decomposition of UH3) at 1073oK, followed by cooling at the rate of 100" per hr. These were vacuum encapsulated, homogenized at 573°K for 3 to 5 hr, and furnace-cooled. Tensile tests were conducted on an Instron machine at a strain rate of 4 x l0-5 per sec. The gripping device was such that the specimen was positioned below the crosshead. Thus, subambient test temperatures could be obtained by immersion of the device in a cooling bath of either liquid nitrogen or Freon-12. The temperature of the Freon-12 was controlled within ± 0.1°K of the desired temperature by automatically monitoring the flow of liquid nitrogen through a copper coil in the bath. Slow-cooling to 77°K was accomplished as follows. The testing device was surrounded by a rubber jacket, open at the top and with small holes in the bottom. Liquid nitrogen, brought up to the bottom of the jacket, entered the holes and vaporized quickly. The temperature was monitored at the specimen with a copper-constantan thermocouple, and a constant cooling rate of 2 deg per min was easily achieved by controlling the level of the liquid nitrogen outside the jacket. RESULTS AND DISCUSSION Low Temperature Ductility Minimum. Resistometric studies of both Nb-H12 and V-H13 indicated that at tem-peratures less than 150°K, virtually all of the hydrogen

Jan 1, 1970

By E. A. Smith, E. R. Parker

METALLURGISTS and engineers have always been interested in the mechanism of high-speed deformation because metals are rapidly deformed in various applications and manufacturing processes. The deformation of metals by impact loads has recently engaged the attention of a number of investigators. Many of their results have not been disclosed but some of the published investigations1-8 have shown that the tensile strength, yield strength and elongation generally increase with increasing strain rate. The investigation reported herein is an attempt to determine the reason for this increase in strength and elongation. Single-crystal copper specimens were broken in tension at impact velocities up to 100 ft. per sec. The distribution of slip bands in the fractured crystals was found to depend upon the strain rate. In the bars broken at high speeds, the slip bands appear to be more numerous. This might account for the higher strength as well as the greater elongation. EXPERIMENTAL PROCEDURE Single crystals of copper (approximately 99.98 per cent) were made in graphite molds by the conventional method of lowering the mold out of the hot zone of a hydrogen furnace at a rate of one inch per hour. Solidification progressed from the bottom upward, forming a single crystal. The crystals were about 0.30 in. in diameter and 4 in. long. They were made into test bars by sliding threaded steel bushings over each end of a crystal and then flowing silver solder between the crystal and the bushing. The inside diameter of the bushings was slightly greater than the diameter of the crystals, to allow space for the silver solder. The bushings were placed so that the gauge length of the crystals was one inch. The assembly is shown in Fig. I, with two views of a fractured crystal. Annealed polycrystalline copper bars of similar shape were machined from solid stock. X-ray measurements were made on all single crystals to determine their orienta¬tions. The results are shown in Fig. 2, where the location of the axis of each specimen is indicated on a standard projection. The bars were broken in a commercial variable-velocity tension im¬pact machine, which has been described in detail elsewhere.7,8 The stress and strain were recorded by means of wire strain gauges and a special commercial oscillo-raph, also described in detail elsewhere.9,10 The equipment and method can be briefly described as follows. The impact machine consists of a motor-driven flywheel containing a two-pronged hammer. This hammer is held retracted in the flywheel

Jan 1, 1944

By William L. Boyd, Eugene L. McCarthy, Laurance S. Reid

Proper control of the moisture content of natural gas is essential to reliable operation of gas transmission and distribution facilities serving northern markets. The moisture content of natural gas is usually determined by dew point measurement at the existing pressure. For any gas of constant moistrire content. the dew Point varies with the pressure. A correlation of the data of several investigators is prezented in graphical form by the authors. These data were correlated by the authors and F. M. Townsend, C. C. Tsao. M. I). Rogers. Jr.. and J. A. Porter. graduate students in chemi(.a1 engineering at the University of Oklahoma. Of articular interest are the hitherto unpublished low temperature data observed by Wickliffe Skinner. Jr., which are included in this correlation. PRESENTATION OF DATA The problem of interpreting water dew points, or saturation temperatures. of natural gas in terms of specific moisture con-tent has increased in importance during the past decade bec.arl.;e of extensive development.; in the transmission and petro-chemical phases of the natural gas industry. Virtually all gas transported to northern and eastern markets must be dehydrated to a low water vapor content to prevent hydrate formation in transmission and distribution lines and resultant interruption.; in gas deliveries. Complete dehydration is required in certain phases of tile petro-chemical industry involving low-temperature operations. It is a well-known fact that the water vapor content of pure hydrocarbon vapors and their mixtures at superatmospheric pressures cannot be predicted with accuracy by assuming validity of the ideal gas laws." Earlier interest in the general problem was concentrated on the water vapor content of pure hydrocarhons and hydrocarbon mixtures in the pressure and temperature ranges common to gas and oil producing reservoirs in order to obtain fundamental data for the improvement of production techniques and the furtherance of reservoir studies. Excellent data are published for pressures ranging from atmospheric to 10,000 psig and for temperatures ranging from 100° to 460° F4,9,10,11 and are found to be in close agreement. However, experimental data at high pressures and temperatures below 100°F are comparatively limited in scope. Experimental data in the lower temperature range have been reported by Laulhere and Briscoe.8 Deaton, et al,2,3 Hammerscllmidt,5,6 and wade," In general, the pressures employed in these investigations ranged from atmospheric to 1.000 psig while temperatures ranged from 32° to 120°F; i.e., the usual conditions encountered in gas transmission line operations, Additional data were reported by Russell, et al,12 at pressures as high as 2.000 psig and covering a rather narrow atmospheric temperature range. In 1947, Hammerschmidt published a correlation of all available data,' in which the water vapor content of gases at saturation. under high pressure and low temperature. was predicted by extrapolation. In 1948, Wickliffe Skinner. Jr.. presented data on the moisture content of a low nitrogen content gas at low temperature and at pressures ranging upward to 1.500 psia.1-3 Comparison of Skinner's experimental data with the extrapolated data of Hammerscllmidt revealed an appreciable variation in the lower temperature range. emphasizing the need for a new correlation which would rely on Skinner's data at lower temperatures. Careful scrutiny of available data suggested that presence of an appreciable quantity of nitrogen in a gas mixture may affect its saturated moisture content so that data obtained from gases with more than three per cent nitrogen were not used in this correlation. CORRELATION OF DATA Data employed in this correlation are presented in Table I. The data of Dodson and Standing.4 McKetta and Katz,9 and Olds, Sage and Lacey10 were compared and found to be in close agreement so that the data of Olds. et al, re-plotted in a more convenient form by the Humble Oil and Refining Co.,' were used for temperatures of 100°F and above. Skinner's data were used for temperatures below 40°F. Between these intermediate temperature limits, the data of Hammerschmidt.7 Wade" and extrapolated data of Olds. et al.1 were tabulated

Jan 1, 1950

By W. J. Millard

Owing to a moratorium in the drilling of crown-land leases in Trinidad during the year of 1931, only 40 wells were spudded in during the first eight months as compared with 110 during the same period in 1930. Nevertheless the production will show an increase of about 400,000 bbl. over that of 1930. An estimate is given in Table 1. Since the oil produced in 1930 was 9,418,907 bbl. and that in 1931 probably will be 9,853,976 bbl., the year 1931 probably will see an increase of about 4.6 per cent. The gross production of crude oil in the colony has increased steadily year by year, with the exception of 1919, when there was a slight decline. A tabulated statement was given last year.' The Petroleum Times of March 21, 1931 (p. 413) gives the total production of 1930 as 9,418,000 bbl. and the average monthly production as 784,833 bbl. The same two items for 1931 are estimated at 9,853,976 and 821,165 bbl., respectively.

Jan 1, 1932

By W. C. Hayes

The site selected for the United States prototype pumped storage project of Union Electric CO. was Proffit Mountain, five miles from Taum Sauk, the highest point in Missouri. Factors influencing final location were: high local relief; satisfactory rock type and structure; and an economic location in respect to existing transmission systems. The upper reservoir was constructed by excavating rhyolite porphyry from the crest of Proffit Mountain and constructing a rock fill dike encircling the area to form a 4350-acre foot reservoir. A 6564-ft tunnel connects the upper reservoir with the generating and pumping facilities. A concrete gravity dam on the East Fork of the Black River forms the 6350-acre foot lower reservoir. Precambrian rhyolite porphyry forms the crest of Proffit Mountain and the floor of the upper reservoir. The tunnel was excavated in rhyolite prophpy, granite porphyry, dolomite, shales and conglomerate. Abutments and the foundation of the gravity dam are in rhyolite porphyry, and much of the valley floor of the lower reservoir is underlain by dolomite and shale. Core drilling provided data on soundness of rock type, structure, depth of weathered zone and potential water loss in the fractured igneous rocks. After a six-year study of pumped storage and cost comparison with alternate stream generating units, the Taum Sauk pumped storage project was authorized by Union Electric Co. on Dec. 11, 1959.' The site selected is located in the St. Francois Mountains of southeast Missouri approximately 90 miles south of St. Louis (Fig. 1). The lower reservoir was provided by damming the East Fork of the Black River, a small tributary of the Black River with a minimum flow of about 1 sec ft. Construction of the upper reservoir was effected by quarrying the crest of Proffit Mountain - five miles from Taum Sauk Mountain, the highest point in Missouri — to provide material for a rock fill dike surrounding the quarried area. This provided a 55-acre mountain top lake with a water depth of 92 ft (Fig. 2). A vertical shaft and tunnel connect the upper and lower reservoirs through the two reversible pump-turbine motor-generator units operating under 800 ft of hydraulic head (Fig. 3). The output rating of the plant is 350,000 kw with daytime generation of about 2.2 million kw-hr under normal use. Night pumping will replenish water to the upper reservoir in about 91/2 hours3. The automatic operation is remotely controlled from the Osage plant and from the dispatchers office in St. Louis. GENERAL GEOLOGY Mountains of the St. Francois area consist of Precambrian granites, granite porphyries, extrusive fel-sites and basic dikes. Basal conglomerates overlain by Upper Cambrian Bonneterre dolomites and shales onlap the exhumed Precambrian knobs and hills and are exposed in the narrow valleys. Cambrian and Ordovician residuum as much as 200 ft thick is present on the slopes of many hills. Proffit Mountain consists of rhyolite porphyry and granite porphyry. All excavation for the upper reservoir was in rhyolite porphyry, and the same rock is present under the Bonneterre at the plant site and under alluvium at the lower reservoir dam site. The region has been dissected to the stage of early maturity with only small upland flats remaining. Considerable local relief (a requisite for the project) approaches 1000 ft. Streams flowing across the Precambrian ridges have formed restricted narrows, termed shut-ins. A shut-in approximately two miles downstream from the plant site provides an excellent site for the lower reservoir dam. TEST BORINGS Preliminary to final approval of the project, 12 test borings were made to determine subsurface geologic conditions (Fig. 2). Drill hole No. 12 at the lower reservoir dam site showed 20 ft of alluvium over solid rhyolite porphyry. Drill holes No. 1, 2 and 3 were drilled in the tail race area to depths of 66 ft, 75 ft and 95 ft respectively, and all bottomed in Bonneterre. Drill hole No. 4 at the plant site provided NX core to a total depth of 98 ft in Bonneterre. Drill

Jan 1, 1965

THE Johnson award for 1926 was given to T. L. Joseph for his experimental work on blast-furnace operation. When the Bureau of Mines undertook its experimental blast-furnace investigation in 1919, a number of operators and metallurgists were doubtful as to the practicability of small-scale tests. Several pre-vious attempts, outside the Bureau, to operate small furnaces had been unsuccessful. However, pig iron was produced in three and four-ton furnaces during the first half of the nineteenth century. The operation of a small furnace did not therefore seem an impossible task. This point of view, together with a realization of the importance of problems connected with the pro-duction of pig iron, prompted the Bureau to undertake this work. Such problems as the feasibility of using charcoal briquets as a fuel, the application of oxygen enriched blast, and the use of new ores and raw ma-terials, in general, can be investigated only at consider-able cost on full sized furnaces, while with an experimental furnace they can be conducted at a com-paratively ;small, cost. The results of small-scale tests are sufficient to determine whether the problem. War-rants the expenditure required for a trial on a com-mercial scale. The accompanying photographs and chart show the various stages of the experimental furnace development. Some idea of the size and shape of furnaces which were tested can be had from the development chart. In oper-ating furnaces A to F, a series of changes were made to increase hearth temperature. Perhaps the most im-portant change was the position of the tuyeres with respect to the bottom of the hearth. The height of the tuyeres above the hearth was gradually increased and the hearth diameter decreased. It was shown by this series of furnaces that metal and slag are the chief source of heat supply to the crucible. For this reason there is a minimum rate at which these materials can be brought into the hearth of a small furnace if it is to function properly. The rate of slag "and metal fall are determined by the burden on the furnace and the rate of blowing. Due to lack of funds necessary to provide ample blowing equipment, hot blast stoves, essential mechani-cal features, and to meet operating expenses, it. was necessary to work with much smaller furnaces, such as G to K shown in the chart. The particular object of these tests was to study the extent to which reactions could be speeded up by decreasing the size of the stock. One decided change, noticed at the beginning of this series of tests, was the effect which coke size had on the production of a strongly reducing gas. Furnace G, 22 in. high, operating on coke crushed to pass 10 mesh, made a gas richer in carbon monoxide than did fur-naces A to F, operating on run-of-the-oven coke.

Jan 3, 1927

By Thomas Read

IN speaking of immaterial problems of industry I am using the word immaterial in its original sense, not consisting of matter; not in its derived sense, unimportant. There is nothing of a paradox in saying that immaterial problems are the most important in human life, for His a matter of everyday observation that much of the news in the daily papers, and most of the world's best literature and drama, deal with human conduct that has for its motive forces that are but little concerned with material things. The engineer's preoccupation with physical forces, in extending his control over them, has not blinded him to the impor-tance of forces that, for want of a better word, I call immaterial; but he has considered that dealing with the one is his job and the other is not. All the evidence of the past decade indicates that the latter are so in-extricably interwoven with the former in modern in-dustrial life that the engineer will have to concern himself with them whether he wants to or not. Some of the most important of the problems arising from the action of these forces relate to the mental hygiene of the workers in industry. Mental hygiene in industry was concisely defined, in terms of the best present knowledge, by Dr. C. Macfie Campbell, speaking last April before the executive com-mittee of the Associated Industries of Massachusetts, and as his statement can scarcely be bettered, I quote it below: "The term mental hygiene is apt to appear vague. The actual stuff with which mental hygiene deals may be briefly reviewed.

Jan 9, 1927

By W. A. Backofen

THE preferred orientations, or textures, resulting from many of the various methods for testing and forming metals have been the subject of numerous investigations.1,2* Despite this large amount of work, however, only a few limited studies have been made of the texture that is developed by torsional deformation. Ono3 found that in severely twisted wires of copper and aluminum a [Ill] direction lies parallel and a [1101 direction perpendicular to the longitudinal axis of the wire. Sachs and Schiebold4 have reported that a double-fiber texture exists in a twisted aluminum wire with both the [Ill] and [loo] directions parallel to the axis of the wire. Twisted iron wires have also been examined by Ono.8 Both the [1101 and [1121 directions were reported as parallel to the axis of the wire. Goss5 concluded from a study of twisted rods of a low-carbon steel that the preferred orientation existing at fracture is quite complex, but that many grains have a [1101 direction parallel to the axis of the wire. In addition to the earlier experimental work, some suggestions have been made about the possible nature of the torsion texture. These suggestions are based on the results of many experiments which indicate that the cold-working texture of a particular metal is largely determined by the geometrical change in shape that the metal undergoes during plastic deformation.1,6 Hibbard and Yen7 have considered the problem of deformation textures and have presented an analysis which is able to explain why equivalent changes in shape should yield similar textures. Therefore, a knowledge of the principal strains associated with torsional deformation would seem helpful in the interpretation of the torsion texture. The necessary analysis has been made of the state of strain in an element of metal lying in the surface of a cylindrical rod or tube that has been subjected to pure torsion.8,9 This analysis shows that the directions of the principal normal strains rotate continuously within a torsion specimen while it is being twisted. After the first infinitesimal amount of twisting, these directions make angles of 45" with the longitudinal axis of the bar. They rotate from this position as twisting proceeds, and after an infinite amount of twisting, the direction of the principal tensile strain is perpendicular, and the direction

Jan 1, 1951

CHARLES KIRCHHOFF, Chairman. ALBERT SAUVEUR, Vice-Chairman. A. A. STEVENSON, Vice- Chairman. HERBERT M. BOYLSTON, Secretary, Abbot Bldg., Cambridge, Mass. John Birkinbine, J. Esrey Johnson, Jr., Felix A: Vogel, William H. Blauvelt, William Kelly, Leonard Waldo, James Gayley, Richard Moldenke, William R. Walker, Henry D. Hibbard, Joseph W. Richards, William R. Webster. Henry M. Howe, E. Gybbon Spilsbury, Frederick W. Wood. Robert W. Hunt, A. A. Stevenson is appointed an additional Vice-Chairman of the Committee. He will serve as Acting Chairman during the absence abroad of Professor Sauveur. For the meeting of the Institute which is to be held in New York City, Oct. 16 and 17, 1913, the following papers are now assured

Jan 7, 1913

By Robert L. Frantz

Progress and improvement continue to be the bywords of a dynamic coal industry. The industry continues to gain strength and expand its horizons in the face of competition from atomic energy and the problems of restrictive legislation. The direct contribution of coal mining and transportation to the national economy is about $3 billion a year ac- cording to a study made by the National Coal Policy conference. Coal remains the backbone of the power industry producing almost two-thirds of all the electrical energy generated by fossil fuels and one-quarter of all the energy consumed in the nation. Power supplied by electric utilities increased 6.9% last year. The chairman of the Federal Power Commission predicted a 7.5% growth rate until 1980 for the nation's electric output. Some 80,500 MW of fossil fired power plant capacity are on order or under construction before 1974, compared to a present capacity, all sources, of about 290,000 MW. The comparable new additions of nuclear power plants is expected to total about 51,000 MW.

Jan 2, 1969

By T. A. Wright

The sampling of waste materials containing copper, lead and tin has taken on a new significance within recent years, and is of increasing importance, on account of the entry of some of the copper refineries into this field and the tendency towards consolidations among the smelters. In the past, such material was sold on the basis either of a rough or grab sample or of casual inspection of the lot. The two principal sources of this waste are the processes of fabrication and the scrapping of automobile, electrical, plumbing, railroad and other equipment. In both cases much material can be sorted, salvaged and sold by classification and grade to be melted "as is" or with the addition of new or virgin metal. The increasing care in classifying exercised in the large manufacturing plants tends to increase the proportion of this usable scrap; on the contrary, the increasing use of more complex and special non-ferrous alloys tends to make sorting and grading more difficult in turnings, borings, clippings, etc., and consequently is making sampling of more moment. In tin, lead, aluminum, and zinc furnace by-products such as ashes, drosses, skimmings, etc., the trade practice of evaluation has not varied much. For instance, tin drosses, battery lead, and aluminum skimmings are ordinarily sold on what is called "metallic button" or "metallic recovery" or ('metallic yield." Copper and lead waste, however, is being sold more and more on actual copper and lead contents based on sample and chemical analyses. This paper will be devoted chiefly to the sampling of materials suitable only for refining and recovery of one or more of the metals present. The methods described are often based on the fact that but one metal, such as copper, is to be paid for. The loss of volatile constituents in melting does not appreciably affect the final copper result, as the "after-melting" assay can be readily calculated to the "before-melting" basis, but if smelter efficiency continues to increase, so that in time zinc, for instance, may be recovered on a paying basis, the method of sampling dirty brass, for example, will have to be changed also. As a matter of fact, we may expect that improved refining processes will make possible the partial recovery of lead and tin which are now lost.

Jan 1, 1928

By AIME AIME

CORROSION of tanks, pipes and other equipment in the oil fields is becoming worse as the production of high- sulfur crudes in the Texas panhandle and west Texas areas increases. It has been estimated that .in certain fields of that State one tank out of every five has to be replaced every year because of the high sulfur content of the crude. One suggested method for combating tank corrosion is the use of .materials which have a high resistance to the corrosive action of hydrogen sulfide and high-sulfur crudes; aluminum is one of these materials. As a result, the United

Jan 1, 1929

By ALFREDO INTZAUGARAT, MIGUEL BERRO

During the years 1943 through 1945, there was a decrease in the total oil production in Argentina. In the fields of Comodoro Rivadavia (Chubut Territory) and Mendoza and Salta Provinces, the production obtained was as shown in Table I. The only place where there was a small increase was Plaza Huincul, in the Neuquen Territory and Lunlunta, in the Mendoza Province.

Jan 1, 1946

By HUBERT O. De

IN December, 1936, several drilling tests were made at the Hubert O. De Beck feldspar mine at Green Mountain, N. C., to determine the most efficient type of hammier-drill bit and drilling method for use at this particular property. This mine is well recognized as having the hardest rock in the Burnsville - Spruce Pine feldspar district and drilling costs always have been high. Local structural deformation has greatly distorted and warped the normal crystalline structure of the feldspar so the rock is much tougher than usual. In studying drilling methods and bit types, available literature was re¬viewed but little specific data could be found on the direct comparison of four-point and six-point drill bits so the following results may be of some interest.

Jan 1, 1937

By William P. Blake

In another paper I have described in general the close association of zinc-blende and iron pyrites in the ore-deposits of southwest Wis consin. These two minerals generally occur together at the same horizon, a sheet of one being overlain by a sheet of the other; and also the pyrites is disseminated through the blende to such a degree that the latter is rendered comparatively worthless for the produc tion of spelter. Ordinarily the pyrites, which is mostly the trimetric marcasite variety, occurs in about equal quantity with the blende and is separated by hand-culliug and chipping; but there are large de posits where the ores are so closely mixed that they can neither be separated by culling nor by any mechanical method. The specific gravity of the two minerals is so nearly the same that attempts often made to effect even a partial separation by jigging have proved un. successful. The smelters of zinc-ores in the Mississippi valley will not take ores which carry more than 7 per cent. of iron; and it is therefore necessary to cull the massive ('jack" with great care and at consid erable expense, in order to bring it up to the market-standard of purity. The results of trials to effect a separation of blende and pyrites in other regions have been equally unsatisfactory. The literature of this branch of metallurgy abounds in examples. In Wisconsin efforts have been made in the past to " burn " the mixed ores in heaps, in order to soften or destroy the pyrites, and facilitate its separation from the massive blende. The same method has also been resorted to when galenite is mixed through the substance of the blende, for the purpose of disintegrating the ore, so that it could be separated by jigging. The custom was to pile the ore and the fuel together. As might have been expected, the results were far from satisfactory. As is usual in heap-roast ing, some portions of the ore were overheated and decomposed; zinc was lost by volatilization; the galenite in some portions was

Jan 1, 1894

DAVID COLE, El Paso, Tex. (communication to the Secretary*).-I notice that Mr. Callow takes issue with me on certain points I have previously contributed to the Transactions, to which I would reply," follows: Regarding Inspiration: Mr. Callow's refinements of gravity methods made just prior to the advent of flotation in the Southwest were intended to be "down to the minute," and the gravity flow sheet for Inspiration ores which he brought out at that time as the result of his long campaign of experimentation was regarded by many as the last word in wet gravity work. It was not my intention to discredit this good work when I said "he threw small light on slime treatment." "Minus 200 mesh," however, is not-synonymous with "real slime." Repeated treatments by gravity methods will result in the separation of a very large percentage of the fine granular sulphides in sizes much finer than 200 mesh, and I gave him due credit for that. The unavoidable losses were made in the "real" slime which I mentioned in the paragraph which Mr. Callow refers to as my "statements on page 1871," and his refinements were not a solution to the real slime problem. Mr. Callow has called attention to the fact that his best results at. Inspiration in gravity work were obtained on Joe Bush ore and he presents a table, viz., Tests Nos. 68, 71, and 72; and asks us to consider and compare these results, made by his refined gravity methods, with the results obtained by 'flotation methods in the new mill "during the second half of 1915 and in August, 1916." Of course, the ore treated in the mill was what happened to come. It was not Joe Bush ore, and therefore comparisons of detail figures are of no value. In regard to Mr. Callow's statements under the caption "Callow Cells Adopted by Arizona Copper Company," I would say that those who have been sufficiently interested to read my paper and' his remarks will notice what amounts to contradictory statements on several points which I cannot allow to go unchallenged. I was on the ground constantly and got my information at first hand. The tables published were the official ones. Mr. Callow was not present during the period and has been laboring under that disadvantage.

Jan 5, 1917

By Henry M. Howe

This paper may be regarded as a report of progress of an investigation into the influence of prior exposure to different high temperatures, under different conditions, on the properties of steel after it has been cooled completely. The following are the chief divisions: II.—Experiments on toughening manganese-steel by sudden cooling. III.—A study of the critical points of common or carbon-steel, chiefly by examining the spontaneous retardations which occur in heating and cooling it, and by examining the ductility of pieces of steel which have been cooled suddenly from different temperatures by quenching them in water or brine. IV.—A brief note on Osmond's theory. V.—A study of the critical points by examining the ductility of pieces of steel which have been cooled slowly from different temperatures at, above, and below them. VI.—A description of the furnace used, with notes on thermoelectric pyrometry. It remains to throw further light on the questions studied by ascertaining the condition of the carbon and the hardness proper, and by studying the microstructure and the fracture of the many pieces treated. I hope to present later the results of experiments in some of these directions. With few exceptions, the experiments have been performed in my private laboratory. I tender sincere thanks to my assistant, Mr. William Haskins, S.B., on whom most of the labor has fallen, for his zealous and intelligent co-operation; to the Sterling Steel Co. for their extra hard steel, Series 17; and to Mr. Joseph Hartshorne and the Pottstown Iron Co. for their soft basic steel. Series 8, 9,10, and 18 were supplied by Messrs. Spaulding, Jennings & Co., of the West Bergen Steel Works; to them also my thanks are due. The temperature of the pieces treated has been very carefully

Jan 1, 1894