Search Documents

By Mitchell, Edmund I.

VARIOUS suggestions as to proper fees for engineering services have been put forth by individual practitioners and by the American Institute of Consulting Engineers, the Connecticut Society of Civil Engineers, the Iowa Engineering Society and the Mahoning Valley (Ohio) Engineers, for the guidance of both the engineer and his client. The American Institute of Architects also has a schedule of minimum charges (revised 1908). So far as can be determined, however, the four national societies representing civil, mining, mechanical and electrical engineering have never given consideration to this question. An examination of technical periodicals published during the past decade shows that these schedules make provision for three methods of charging; i.e., (A) a percentage of the cost of the completed project; (B) a per diem rate; and (C) a fixed sum. Suggested minimum charges are as follows:

Jan 1, 1921

By R. W. Nash, A. E. Schwaneke, V. R. Miller

The Bureau of Mines developed a detector for controlling sorting devices to separate the copper-bearing fragments from the barren portion of Michigan native copper and western prophyry copper ores. A successful sorter could be used to preconcentrate the ore and eliminate costly hoisting or hauling of waste. An induction balance unit was developed and used in sorting tests on crushed sized - 2.5 + 1. 3-cm (- 1 + 1/2- in.) ores from the Kingston (0.9% Cu) and Centennial (1.6% Cu) mines of Upper Michigan. Concentrates of 4.0% and 7.5% Cu, respectively, were obtained at recoveries of 85 and 80% of

Jan 8, 1978

By W. S. CAYPLESS, H. O. Hofman, E. E. HARRINGTON

I. INTRODUCTION. LIME-ROASTING is a term proposed by Ingalls 1 for the operation of forcing air under pressure through a mixture of galena and lime at the kindling-temperature with the object of oxidizing lead and sulphur and of fritting or fusing the charge. If, finely-divided galena were treated in this manner without the addition of lime, the heat set free by the oxidation of part of the lead and the sulphur would be sufficiently great to fuse undecomposed sulphide, and thus stop desulphurization. Besides the chemical action that the addition of lime, limestone or gypsum to the charge may have, the admixture has the physical effect that it keeps the particles of galena separated from one another and accessible to the oxidizing effect of the air. At present, three methods of lime-roasting are carried out on a working-scale, the Huntington-Heberlein, the Carmichael-Bradford and the Savelsberg2 processes. In the last, which interests us here, an 8-ton charge is made up of galena, limestone and perhaps some siliceous or ferruginous flux; the whole is crushed to pass a screen with 3-mm. holes and moistened with 5 per cent of water. It is fed gradually into a bowl-shaped converter, 6.56 ft. in diameter, supported by trunnions attached to a truck. On the .bottom the converter has a grate with blast-inlet beneath. In starting, the truck with the converter

Jan 1, 1907

Organization Place Date International Mining Convention (Auspices, Van- 1919 couver Chamber of Mines) Vancouver, B. C. Jan. 8-10 American Institute of Consulting Engineers, Inc... New York, N. Y. Jan. 13 American Society of Civil Engineers New York, N. Y. Jan. 15-16 Institute of Chemical Engineers Chicago, 111. Jan. 15-18 American Wood Preservers Association St. Louis, Mo. Jan. 28-30 American Society of Heating and Ventilating Engineers New York, N. Y. Jan. 28-30 Automotive Engineers New York, N. Y. Feb. 4-6

Jan 1, 1919

By Arthur A. Center

AT the beginning of 1944 it was expected that the production of metallic zinc in the United States from domestic and foreign concentrates would exceed the 1943 figure though domestic production of concentrates was expected to drop below the 1943 rate, mostly in the Tri-State area. Imports of concentrates were estimated to more than take care of such deficiency. North American concentrate production, available for import to the United States or elsewhere during the year, was estimated at over 200,000 tons recoverable zinc content; South American at about 65,000 tons; Australian at about 50,000 tons. Production of both concentrates and metal in the United States, however, did drop, attributable in considerable part to man-power shortage in the industry. However production exceeded consumption, which fell off, and stocks of metal increased. These stocks have increased since the middle of 1942 but production and consumption are coming nearer to a balance. The A, B, and C premiums, which have played an important part in keeping up domestic production of concentrates, extend only to the middle of 1945 by present legislation. Congress is being asked for their continuance during the war and

Jan 1, 1945

By M. R. Tek, K. H. Coats, D. L. Katz

A large number of boundary value problems encountcred in unsteady-state heat transfer, fluid flow through porous media, neutron diffusion and mass transfer involve the solution of a linear, parabolic partial differential equation commonly refcrred to as the diffusivity equation, where U is the dependent potential variable. K is the diffusivity (hydraulic, thermal, neutron, etc.) and 1 is the time variablc. Solutions to Eq. I are available in the literature for a wide variety of initial and houndary conditions. The great majority of these solutions are ohtained for geometric boundaries corresponding to linear. cylindrical or spherical flow models. A typical engineering application where the solution to Eq. 1 is required is the calculation of underground water encroachment across the boundaries of oil or natural gas reservoirs, In this particular area of application, the reservoir boundary is invariably approximated by circular geometry. However. the areal shape of many reservoirs can be better approximated by elliptic rather than circular boundaries. Thus the need for a general method of solving the diffusivity equation in elliptic coordinates arises in this problem as well as in other engineering applications involving elliptic boundaries. The solution to the diffusivity equation usually in volves the Error Function for the linear flow model, Bessel functions for the radial flow model and trigonometric or Legendre functions for the spherical flow model. It is well known that the general solution to the diffusivity equation in elliptic coordinates involves Mathieu functions. The significance of Mathieu functions in the analytical treatment of the diffusivity equation in elliptic coordinates is discussed in the literature However, these references do not providc analytical solutions useful in practical engineering problems. The objectives of this papcr are the development of the equations describing the unsteady-state liquid flow through a porous medium with an elliptic inner boun- dary, the development of a numerical method of solving these equations and, finally, a comparison of the water encroachment quantities calculated from the elliptic flow equation with those calculated from the radial flow equation. While the specific problem treated in this paper relates to unsteady-state liquid flow through a porous medium, the basic equations and computational techniques devcloped will apply equally well to problems occurring in the other areas of engincering interest mentioned previously. The solution given here is limited to a single case in which thc outer boundary encloses an area 100 times that of the inner boundary. DESCRIPTION OF THE FLOW MODEL Fig. 1 shows the flow model upon which the calcu lations presented in this paper are based. The inncr and outer houndaries of the flow model are represented by two confocal ellipses with major and minor axes, respectively, equal to 2a1, 2b1, and 2a, and 26,. The height of the elliptic cylinder flow model is denoted by 17. The following assumptions are employed in the development 01 the equations governing the unsteady-state liquid flow through the described flow model. 1. Uniform porosity and permeability throughout the flow model

Jan 1, 1932

By Simon D. Strauss

The world appetite for minerals in the, third quarter of this century grew at a higher rate than had been anticipated. To illustrate, consider the experience of four, commodities. Excluding the Communist bloc, sometimes referred to as the centrally planned economies, demand for aluminum increased at a compound rate of 8.6% between 1950 and 1975,; copper rose by 4.4%; iron ore by 5.5%; and tin, the laggard in the group, by 2%. Except for tin, the figures are substantially greater than growth rates anticipated in 1950 in the Paley Commission report and other studies. The growth rate was not evenly distributed in geographical areas. Professor Wilfred Malenbaum of the University of Pennsylvania did an interesting study breaking these figures down as among three principal sources of demand -- the United States, other industrialized nations (which he referred to as the "rich lands"), and the developing world (which he referred to as the "poor lands").

Jan 1, 1982

PRESIDENTS DAVID THOMAS 1871 Born November 3, 1794, Cadoxtan, Glamorganshire, South Wales. Died in 1882. Attended schools in Wales. Came to America in 1839. A.I.M.E.: Member, 1871; Honorary Member. Iron manufacturer; inventor. Built first anthracite fired hot-blast furnace in America. Known as the "Father of the Lehigh Valley." President, Catasauqua and Fogelsville Railroad; Director, Lehigh Valley Railroad; Founder, Thomas Iron Co. and St. Luke's Hospital at Bethlehem, Pa.; Trustee, Lafayette College.4 ROSSITER WORTHINGTON RAYMOND 1872-1874 Born April 27, 1840, Cincinnati, Ohio. Died in 1918. Brooklyn Polytechnic Institute, 1857; Lafayette College, Ph.D., 1868; Lehigh University, LL.D., 1906; University of Pittsburgh, Hon. LL.D., 1915., Gold Medal, Institution of Mining and Metallurgy (London). A.I.M.E.: Founder, Member of 1871; Vice President, 1871, 1876-1877; Secretary, 1884-1911; Secretary Emeritus, 1911-1918; Honorary Member. Consul¬ing mining engineer; practicing lawyer, sailor, soldier, writer, orator, editor, theologian, teacher, novelist, chess player. Recognized as the "Grand Old Man of the Institute." ALEXANDER LYMAN HOLI,EY 1875 Born July 20, 1832, Lakeville, Conn. Died in 1882. Brown University, 1853; Hon. LL.D., 1878. A.I.M.E.: Member, 1871; Vice President, 1874; Manager, 1877-1879. Bessemer Medal (Iron and Steel Institute, London), posthumously. Brought bessemer process to United States. A statue was erected in Washington Square in his memory and presented to the City of New York in 1889. The inscription notes: "foremost among those whose genius and energy established in America and improved throughout the world the manufacture of bessemer steel." ABRAM STEVENS HEWITT 1876 Born July 31, 1822, Haverstraw, N. Y. Died in 1903. Columbia University, 1842; Hon. LL.D., 1887. A.I.M.E.: Member, 1871; Manager, 1872-1875. Bessemer Medalist and Honorary Member, Iron and Steel Institute (London). Gold Medal, Chamber of Commerce of New York City. Philanthropist, lawyer, statesman, publicist, pioneer in the iron and steel industry. Mayor of New York City in 1887. Business partner of Peter Cooper, Executive Manager of Board of Trustees, Cooper Union, New York City.

Jan 1, 1947

By John E. Young

U.S. Steel Corp.'s Winifrede mine is operated by Lynch District in the mountainous region of eastern Kentucky. This region is characterized by narrow finger ridges and precipitous slopes, which present both an opportunity and challenge in the design and selection of coal-handling facilities for the movement of coal from the section belts to the railrod cars. Lynch District selected diesel-powered locomo¬tives and 100-ton articulated cars capable of negotiating sharp curves. The drop¬bottom mine cars are equipped with longitudinally hinged doors that are auto¬matically opened and closed. Lynch District selected a large-diameter steel-lined borehole for lowering the coal approximately 1000 ft from the seam level to the valley floor railroad load-out point. Taking advantage of gravity, the presized coal is "lowered" vertically approximately 720 ft to existing entries of a previously abandoned mine. The coal is then conveyed horizontally into storage. The coal¬handling facility from the mine-car dump to the railroad load-out point is fully automatic through use of tone control. TV cameras are installed along the facility to continuously monitor the strategic points. The diesel locomotives are either directly operated or remotely radio-controlled, depending on the functions Per¬formed. U.S. Steel Corp.'s Winifrede mine is operated by Lynch District in the mountainous region of eastern Kentucky. This region is characterized by narrow mountain ridges and precipitous slopes which present both an opportunity and challenge in the design and selection of coal-handling facilities for the movement of coal from the section belts to the railroad cars. The narrow finger ridges precluded use of under¬ground haulage and, thereby, presented the opportunity to use high-capacity equipment on the outside bench. The precipitous mountain slopes, steepest at the Wini¬frede seam horizon, presented a challenge to select a solution for lowering the coal approximately 1000 ft from the seam level to the valley floor railroad load-out point. It was evident from the start of planning that these two factors predominated; namely, rail haulage and coal lowering, and solutions to these would determine the final design of the Winifrede mine coal-handling facilities. The Winifrede mine derives its name from the Wini¬frede Seam which comprises the total reserve recov¬erable from this facility. The seam is 5 ft high with a good siltstone bottom and competent shale or sandstone roof. The seam is at an elevation of 2700 ft where the mountain ridges are long and narrow. This configuration of the reserve was ideal for conveyor belt installation to transport the coal from the working face to the outside bench. The preclusion of underground rail haul¬age permitted an opportunity to review the type of locomotive power and to select high-capacity equipment without the limitations associated with underground systems. Since the basic electrical design of the mine was al¬ternating current, with rectification to direct current for shuttle cars required only in the face areas, there was no point in bearing the burden of additional cost of dc trolley installation. And, since the haulage would re¬quire only a few tunnels to negotiate sharp points and to reach the back side of the reserves, diesel power was selected for the haulage locomotives. To provide stability on the almost continuously curv¬ing track and to provide the maximum width of haul¬age equipment, both locomotives and mine cars, stan¬dard railroad gage was chosen to offer the largest choice of equipment. The decision was made to select a standard 45-ton railroad diesel locomotive but to lower the cab height to reduce tunnel excavation requirements. The mine car was the next challenge. Past experience in Lynch operations indicated that drop-bottom cars would be a successful application with the free-flowing coal. The search was for a drop-bottom car within the dimensions of the locomotive to discharge the coal in the shortest time. Numerous types were considered and visits made to various sites to observe cars in operation.

Jan 1, 1972

By J. Handin, S. J. Bauer, M. Friedman

Deformation mechanisms in room-dry and water-saturated specimens of Charcoal Granodiorite, shortened at 10-4s-1, at effective pressures (Pe) to 100 MPa and temperatures to partial melting (?1050°C) are documented with a view toward providing criteria to recognize and characterize the deformation for geological and engineering applications. Above 800°C strength decreases dramatically at effective pressures ? 50 MPa and water-weakening reduces strength an additional 30 to 40% at Pe = 100 MPa. Strains at failure are only 0.1 to 2.2 percent with macroscopic ductility (within this range) increasing as the effective pressures are increased and in wet versus dry tests. Shattering (multiple faulting) gives way to faulting along a single zone to failure without macroscopic faulting as ductility increases. Microscopically, cataclasis (extension microfracturing and thermal cracking with rigid-body motions) predominates at all conditions. Dislocation gliding contributes little to the strain. Precursive extension microfractures coalesce to produce the throughgoing faults with gouge zones exhibiting possible Riedel shears. Incipient melting, particularly in wet tests, produces a distinctive texture along feldspar grain boundaries that suggests a grain-boundary-softening effect contributes to the weakening. In addition, it is demonstrated that the presence of water does not lead to more microfractures, but to a reduction in the stresses required to initiate and propagate them.

Jan 1, 1982

By T. A. Read, H. K. Birnbaum

Deformation of AuCd alloys having the 8 (orthorhombic) and (3" (tetragonal) structures occurs by the stress induced motion of twin boutdaries. A restoring force acts on displaced twin boutdaries as a result of internal energy increases in the volume through which the boundaries are displaced. The phenomonology of the twin boundary motion is described and a mechanism for twin boundary motion and the restoring force is proposed. A time-dependent stabilization behavior of the twin boundaries, which is observed after the twins are formed by the diffusionless phase transformations, is described. THE AuCd 8 phase (ordered bcc structure) exhibits a transformation to a phase having an orthorhombic structure, 8' (space group D'), for compositions in the vicinity of 47.5 at. pct Cd and to a phase having a tetragonal structure, 8" (point group 4/m, m,m), for compositions in the vicinity 50.0 at. pct Cd. Both transformations are diffusionless, occur on cooling at 60" and 30OC, respectively, and are crystallo-graphically reversible.' They are accompanied by an inhomogeneous deformation which was observed to be twinning in the low-temperature phase. 3'4 The transformations may occur by a "single interface" or by "multiple interfaces."5'6 In the "single interface" transformation, the twinned product phase consisted of two twin orientations as shown in Fig. 1. In the multiple interface transformation the product phase contained "domains" each of which contained two twin orientations, Fig. 2. Deformation of specimens containing transformation twins was achieved by motion of the twin boundaries. Releasing the applied stress resulted in the displaced twin boundaries returning towards their initial positions. This "pseudo-elastic" behavior of the boundaries varied with time after the formation of the twin boundaries by the transformation.

Jan 1, 1961

By John A. Church

Jan 1, 1880

By Frank Van Horn

INTRODUCTION IN June, 1911, the writer spent a few days in studying the economic geology of the vicinity of Park City. During this rather hurried visit a number of specimens of ore were collected, which have since been examined. The results of these investigations show that bournonite (PbCuSbS3) is present in the ores in greater or less quantity. This fact has never before been reported, as far as can be learned. The failure to recognize this mineral is due to its similarity to tetrahedrite, with which it has probably been confused during a long period of years. Jamesonite (Pb2Sb2S5) has been reported from the region in a rather doubtful manner, but the writer has seen it in notable amounts from several mines, and can offer the first analysis of this mineral from the district. Calamine (H2Zn2SiO6) was found at one mine and has never been recognized and reported from the district.

Jan 8, 1914

By Notman, Arthur

THIS is a day of surpluses, some good and some not so good. One can hardly pick up a newspaper, magazine, review or economic treatise without confronting the fact that we have or are threatened with more .of certain goods than we have use for, whether it be corn, wheat, cotton, coal or oil, -lumber, 'leather, newsprint, automobiles, zinc, lead, copper or what not. How did this unprecedented state of affairs arise? Who is to blame? How shall we avoid smothering ourselves in our own production? The voice of the farmer is raised in appeal to the Government to relieve him from the dilemma of his own fertility. In answer the Government employs thousands of experts and spends millions of dollars to aid the farmer. But to what end? To make him still more efficient so that he may produce even greater surpluses? Not satisfied with the result, it spends other millions to prepare vast areas of the arid land of the West for more farmers to cultivate and insure yet larger surpluses. Then what? Naturally another appeal to the Government to fix prices by financing the

Jan 1, 1928

By V. L., McCutchan

FORM of ore bodies, strength of wall rock, and quantity of water that must be handled differ so greatly in the various districts in which the Corporation operates that a variety of mining methods have to be employed. All are underground, however, with the exception of glory holes at Cerro de Pasco from which siliceous silver pacos ore is obtained. In general, the ors is in many relatively small bodies unsuitable for hulk mining, such as caving or top slicing. The strength of the rock and ore rarely permit open stopes, though shrinkage is successfully used on various veins with strong walls, particularly in, Casapalca. Horizontal cut and-fill and square-set stoping with careful filling are the principal methods employed, with the necessarily higher cost for supplies and labor offset as much as possible by care in the avoidance of dilution. The mines at both Morococha and Casapalca are notoriously wet, and even at Cerro de Pasco the quantity of water was enough to retard deep development until the perfection of electric pumps. In Morococha particularly, the extension of successive levels, first from adits of moderate length, then from shafts and heavy pumping installations on the 750 and 1000 levels, and finally by the 30,564-ft. Kingsmill tunnel, was one of the most difficult and long continued fights against water and resulting heavy ground that is recorded in mining history.

Jan 1, 1945

By C. V. Millikan

THE year 1930 in the petroleum industry has been characterized by the establishment of large potential production of crude oil. This has resulted in closer cooperation between companies by proration and unit operation agreements in order to afford an equitable outlet to all, and to prevent a flood of oil being forced on the market with attendant tremendous material and economic waste. Drilling wells in proved areas and wildcat wells are fewer than in the past several years. Restricted production and low prices have caused greater effort to increase producing and recovery efficiencies. Increased refinery efficiencies have amplified the effect of overproduction. Pipe line departments have been especially busy. New oil lines have reached more refineries by new and shorter routes. Establishing greater gas reserves by new fields has justified new gas lines to industrial centers, and has brought this fuel to thousands of new domestic consumers. Two long gasoline lines, a new venture in pipe lines, are being built to obtain a lower cost of transportation and less loss between the refineries and their distribution centers. The chairmen of the various divisions have discussed the developments of their respective branches more fully in the following reviews.

Jan 1, 1931

By N. L. ALISON

MUCH has been published on the general subject of metal mine ventilation but, so far as I can discover, few specific data on selection of fan equipment to meet the requirements of a given mine ventilation problem are available. This article is intended to point out some of the more important considerations which influence the selection of such equipment. It will be assumed that the mine operator is able to determine the quantity of air which is necessary in the various parts of his mine to produce the required results and the pressure in inches water gage needed to circulate this quantity of air through the mine. There may be instances in which this assumption is not justified, but the fact remains that, with proper engineering talent, these data can be approximated sufficiently close for practical purposes.

Jan 1, 1930

By D. L. Rainey, E. R. Goter, W. R. Hudspeth

THE area in which spodumene-bearing pegmatites occur extends from Gaffney, S. C., in a northerly direction to Lincolnton, N. C., a distance of about 16 miles. The zone averages 2 miles in width. Interest in this area was first aroused by the discovery of small amounts of cassiterite in the pegmatites and in greissen which occurs on the walls of some of the pegmatites. Attempts were made from 1880 into the 1920's to mine and concentrate cassiterite, but there were no successful operations. In 1935 L. M. Williams became interested in the area and began prospecting by trenching and sinking several small shafts. He gradually gained control of a considerable acreage south of the city of Kings Mountain, N. C. Mr. Williams states that he produced some ore from a shaft which he shipped to the Maywood Chemical Co. in the late 1930's. In 1937 G. H. Chambers of the Foote Mineral Co. visited the area and examined several properties, but the lithium market was too small to support the necessary concentrating plant.

Jan 9, 1953

By H. Cecil Spicer

The results described in this article are based on field work conducted during the periods APril-May, 1939, and MaY-JulY, 1940. The United States Potash CO. is mining potash on Government land under a permit from the Department of the Interior and the geophysical investigation mas completed under a cooperative arrangemerit made between that company and the Conservation Branch of the Geological Survey. The writer, a member of the Section of Chemistry and Physics of the Geologic Branch, was assigned to this investigation. Four definite objectives were in mind for the geophysical work in the studies over the salt deposits. The first was to determine the measure of success that could be attained in this type of work with the resistivity methods that were to be employed. These methods had been introduced into the work of the Conservation Branch by Benjamin E. Jones for the investigation of dam sites, and have been used under his direction by the author for such work. If the method proved to be applicable, an l was to be made to contour the top of the salt beds and also the other formation boundaries known to be present in this area. Salt-water aquifers were to be studied in an effort to determine their boundaries, and an attempt was to be made to delineate the potash-bearing beds. Others have made, and reported, resistivity studies over saliferous deposits in different areas. Friedell and Messrs. Schlumberger2 reported geophysical work performed in the disrovery of the salt domes of Alsace; Carrette and Kelly3 described the geology of the same area. Leonardon and Kelly4 published a resistivity curve obtained over the Hettenschlag dome, and a further discussion of this same area was given by the Messrs. Schlum-berger5 in a communication. Messrs. Alty6 described studies 0" salt deposits in which the sing[e-probe method was used. Sinerez7 mentions that electrical methods were tried over salt deposits in Spain. Geoffrey and Charrin8 show a resistivity curve obtained over marl, gypsiferous marl and salt which is similar to that obtained over the New Mexico salt deposits. Kelly9 reported resistivity work performetl with the ground comparator of Zuschlag over the salt deposits near Syracuse, N. Y., where the Salina formation is at a depth of 700 to 800 ft. Some structural studies on the potash basin of Alsace are described by Poldini.10 Another single-probe resistivity study, made over salt deposits in New Mexico, is briefly described by Heiland,ll through the courtesy of Harry Aurand, of the Midwest Refining CO.

Jan 1, 1942