Search Documents

J. H. HEGINBOTHAM, a, metallurgist of the General Engineering Co., talked on "Current Milling Practice at Kirkland Lake," at the December meeting of the Utah Section. The ore is enough alike through the whole district so that some generalizations and comparisons may be made. The question as to whether or not the flotation process should be used in the flowsheet for extracting gold by cyanide solutions is still being vigorously debated, and it will seemingly need some years for a definite answer to be given. Most of the gold is either free, though much of it is finely dispersed in quartz, or occurs with pyrite. At times there may be 2 per cent of telluride compounds in the ore, but the amount of gold telluride present is small and has not been definitely established. It has been shown by Dr. Haultain and others that though gold tellurides may be so finely disseminated that it is necessary to grind the ore exceedingly fine, the compounds themselves are not difficultly soluble. (An increase in temperature helps to dissolve tellurides, and also to settle pulps.) It is likely that if the ore were ground through 400 mesh, practically all of the gold would be soluble. As it is, with 96 to 98 per cent of the ore ground to minus 200 mesh, and some 70 per cent minus 325, the cost of

Jan 1, 1934

Maryland Geological Survey, Johns Hopkins University, Baltimore, Md Edward B Mathews, State Geologist A list of publications-and maps will be sent upon request. The Survey published 12 general reports between the years 1897 to 1928, inclusive Vols. 1 and 9 are out of print, others may be obtained at the uniform price of $1 each. Separates of many of the papers contained in the volumes may be had; in the following list a few of the available separate papers of most direct interest are cited. Vol. 1, pt 4, Bibliography and cartography of Maryland, by E B. Mathews (1897), 25 cents, vol 5, pt 4, Report on the coals of Maryland, by Clark and others (1905), 25 cents paper bound, vol 6, pt 1, The physical features of Maryland, by E B. Mathews, W. B. Clark and others (1906), 25 cents paper bound, including map, 75 cents, vol 8, pt 2, Maryland mineral industries (1896¬1907), by Clark and Mathews, free, vol 8, pt 3, Report on the limestones of Maryland, by E B Mathews and J. S Grasty (1909), 25 cents paper bound, vol 9, pt. 3, Report on the iron ores of Maryland, by J T. Singewald, Jr. (1911), 25 cents paper bound, vol 10, pt 1, The geography of Maryland, by W B. Clark (1918), 25 cents paper bound Vol 11, pt 1, The coal formations and mines of Maryland, by various authors (1922), 35 cents paper bound, vol 11, pt 2, The fire clays of Maryland, by various authors (1922), 35 cents paper bound Most of a series of Systematic Reports on the geologic formations found within the state are also available: Pliocene and Pleistocene, $1; Upper Cretaceous, $5; Lower Cretaceous, $5, Triassic (in preparation), Carboniferous and Permian (in preparation);

Jan 1, 1933

By Francis A. Thomson

IN reviewing mineral industry education a year ago, occasion was taken to congratulate the Institute in general and to felicitate the Education Di- vision in particular on "the most gratifying growth which is taking place in Institute consciousness in regard to its responsibility for the recruitment and adequate training of student personnel and for the successful bridging of the difficult gap between graduation and achievement of professional status." Continuation of this growth of interest throughout 1939 is a recognition of the validity of the splendid statement of George Otis Smith that the mining students of today are the ore reserve of the Institute for the future. In this connection one recalls the equally apt expression of another distinguished geologist, George M. Fowler, who, speaking of exploration for ore deposits, says, "The place to look for elephants is where elephants have been found."

Jan 1, 1940

By J. J. Mike

During the past few years the combination of continuous billet casting with in-line reduction has been studied and several machines have been built with this capability included in the design parameters. (1,2,3,4,5) In-line reduction and continuous casting in combination are obvious and attractive. As pinch rolls are already in place for the continuous casting operation, it can be readily seen that a redesign of the mechanical and electrical equipment of the pinch rolls is all that is necessary to have in-line rolling. There have been numerous in-line reduction experiments conducted by simply increasing the pinch roll pressure on existing machines. (6,7,8,9) These generally failed to produce quality billets and often resulted in internal metallurgical defects (Figure 1).

Jan 1, 1972

By H. B. Pulsifer

THE unprecedented high price of zinc ore prevailing through the early months of 1915 caused great activity in the Joplin district of Missouri. The Media mill is conspicuous as one of the first of the new "big mills" of the district. The mill was built over a mine previously worked but abandoned in 1912 because of the leanness of the ore and the large quantity of water encountered. The ore prices prevailing-$100 a ton in June, 1915, as against $50 in 1912-favored the new undertaking. The mill was designed for good recovery so that it might operate in times of depression. In design and equipment, the mill is exclusively local in conception and construction. Former Exploitation The tract of land is a part of the large Guinn holdings; 70 acres are comprised in this particular lot, which is situated just a mile north of the center of Webb City on the Alba line of the Southwest Missouri Electric Railway. The ore lies 242 ft. below the' surface at the top of the knoll which is surrounded by the well-known properties: Black Cat, Ground Floor, Florence, Hurry-Up, Electrical and Mercantile. Since the abandonment, in 1913, of the Yellow Dog. a bit farther to the north, the Black Cat, Ground Floor and Florence workings had been flooded. However, as there was no cut through from this side into the area it was proposed to exploit, it was thought that moderate pumping facilities would take care of the water.

Jan 5, 1917

By J. Burns Read

IT IS the purpose of this paper to summarize, as far as possible, the metallurgical information and experience gained by the Ordnance Department, during the War, in the manufacture of artillery cartridge cases, to describe the tests to which artillery cartridge cases were put, and to summarize the knowledge and experience gained in this testing. The authors wish to acknowledge the aid given by manufacturers, army officers, and civilian employees of the Ordnance Department in obtaining these data. Artillery cartridge cases are cold drawn from circular disks punched from strips of rolled brass. The manufacture involves from 25 to 30 main operations, which are done almost entirely on a punch press. Descriptions of the operations have appeared in various periodicals and, therefore, will not be given here. After each cupping, or drawing, operation, except the last, the cases are annealed at from 540° to 650° C. (1000° to 1200°F.), to remove all the hardening stresses set up in the metal and to allow complete recrystallization. After each annealing, the cases are pickled in niter cake or sulfuric-acid solution and then washed in water to remove all traces of acid. In some instances, the cases are then immersed in a cyanide-salt solution, and afterwards rinsed in water, to remove the thin layer of copper that forms on the surface of the cases during the acid pickle. The last cold-drawing operation is followed, by the heading operation which, by flattening the head of the case on the outside, causes the metal to flow on the inside to approximately the proper finished dimensions. The mouth, or open end, is then annealed at 430° to 480° C. (800° to 900° F.) by immersion in a salt bath or by gas flames. After being washed, the cases are tapered, when they are ready for machining, inspection, and testing.

Jan 4, 1922

By James A. Crookston, William D. Fitzpatrick

Committee C-8 of the American Society for Testing and Materials defines "Refractories" as "Material, usually nonmetallic, used to withstand high temperature," and it defines the term "Refractoriness" thus, "In refractories the capability of maintaining the desired degree of chemical and physical identity at high temperatures and in the environment and conditions of use." The ability to withstand high temperatures is critical to classifying a material as a "refractory." However, as the foregoing definition of "refractoriness" implies, the refractory material may be subjected to and is expected to resist not only high temperatures but a variety of other destructive forces incident to its use. These include abrasion, impact, thermal shock, chemical attack, and high level loads at high temperatures. The various industrial applications of refractories represent an infinite variety of combinations and degrees of severity of these destructive forces, including high temperatures. Naturally, such a variety of application conditions leads to a need for a wide variety of refractory products to satisfy those conditions. The number of refractory products available is great enough that some form of classification is necessary to a discussion of refractories. Refractories may be classified in several ways, but the most suitable one is based on their general compositions and to lesser degrees on their physical condition and distinctive properties. The primary types of brick include aluminosilicate brick (fire clay and alumina), basic brick (magnesia and chrome ore, alone and in various combinations), silica brick, insulating brick, and special refractories (carbon, Sic, ZrO,, zircon, borides, and nitrides). Brick are, of course, preformed and are usually heat treated at high temperatures before use, but are in some instances unburned and/or chemically bonded, including the relatively new class of tar-bonded magnesia and/or dolomite brick. In addition to preformed refractories, another broad category includes the so-called specialty refractories, which are usually made in the same types as itemized for brick-bonding mortars and high temperature cements, hydraulic setting castables or refractory concrete, plastic firebrick, and ramming mixes. Refractory grains, such as fire clay and high alumina calcines, dead-burned magnesite and periclase, and dead-burned dolomite are also considered refractory products. Brick are also classified on the basis of physical dimensions, as standard sizes and special shapes. The standard sizes are those which are of definite shape and design and are designated as 9 x 4 ½ x 2 ½ in. and 9 x 4 ½ x 3 in. straights and series. All other brick of non- standard sizes are referred to as special shapes. These come about as a result of a particular need for a given furnace or for a particular application.

Jan 1, 1975

By George B. Lee

During the two years in which the new reduction-works of the Copper Queen Consolidated Mining Co. have been in operation at Douglas, Ariz., there has developed a remarkable condition in regard to the corrosive action of the water used to cool the jackets of the blast-furnaces. Were it not for the many contradictory features, it might pass as one of the unavoidable troubles due to the composition of the water. This water, obtained from wells 600 ft. deep, is also used in the steam-boilers, and its composition, as shown by the following analysis, does not indicate the presence of any ingredient which would explain the corrosion: Grains Per U. S. Gal. Silica,...........0.861 Iron oxide and alumina,....... 0.223 Calcium carbonate,....... 0.261 Calcium sulphate,................. Magnesium carbonate,........... Sodium and potassium sulphates,..14.850 Sodium and potassium chlorides,.9.732 Sodium and potassium carbonate, . 6.482 32.409 The jackets are made of inner plates 0.5 in. thick and an outer plate # in. thick, with 3/8-in. stiffeners between the inner and outer plates. In from 10 to 12 months the inner plates have been reduced by corrosion to a thickness of from + to & in., while the outer plate in the same time is reduced by less than 1/16 in., and the stiffeners show very little corrosion. The plates are pitted and eaten away in some places more than in others. There is practically no scale found on the jackets, but when cleaned considerable iron oxide is found in the bottoms. With an action so marked, serious trouble would be expected in the boilers, but, on the contrary, a recent inspection by a

Jan 1, 1908

By Oliver Bowles

A HEAVY gel of bentonite clay has been proposed as an effective lubricant to speed down the ways to sea, river, or lake, the mighty cargo ships now hitting the water at the rate of about three a day. Another unusual application of a nonmetallic mineral is in food conservation, for the claim has been made that the next new item on the menu for poultry and rabbits will be vitamin tablets prepared from mont-morillonite clay. These uses have minor importance but illustrate not only the diversity in utilization, but the notable trend in 1942 toward mobilizing nonmetallic minerals for the war program. Although occupying less headline space than iron, steel, copper, aluminum, magnesium, and other metals, the nonmetallics are filling important emergency needs. Mica and quartz crystal are essential to communication; asbestos is urgently needed in fireproof heat and electrical insulation; and strontium minerals are utilized in the manufacture of signal flares and tracer bullets.

Jan 1, 1943

By K. Prins

ONE of the more pressing problems faced by the coal industry today is the development of adequate means for meeting conservation laws, particularly those involving stream pollution, in various parts of the country. Discharge of dirty coal washery water into streams and rivers is almost universally frowned upon. Many states have enacted laws carrying heavy fines to curb the practice. The Prins stream-cleaner is one of the latest machines to enter the market. It is closely related to the cyclone thickener in principle. Eleven stream-cleaners are currently operating, ranging in size from 4 to 16 in. diam. In more recent installations the water enters directly in line and on a tangent with the impeller. The impeller consists of a vertical shaft up through a packing gland and bearings, and a V-belt pulley. The lower part is a tubing fastened to the shaft above, extending through the water intake compartment and provided with six vertical flat bars welded to the tubing. Portholes are situated in the upper end of the tubing, immediately below the point where shaft and tubing join together. The portholes are placed so that they are in open communication with the upper compartment of the stream-cleaner from which the processed water is discharged. The impeller is motor driven with a wide range vari-pitch drive employed between motor and impeller. The motor is mounted vertically, and the mounting provided with a vertical hinge allowing for needed adjustment of the wide range vari-pitch drive. The dirty coal washery water entering the machine under 20 lb psi pressure, flows from the compartment above the impeller, between the impeller blades, and is whirled around in the vertical section of the impeller enclosure. The speed of the impeller supplies centrifugal force and velocity required for separating suspended solids from water. The lower part of the machine consists of a cone, whose action is similar to other machines of the same type. The underflow discharge orifice is a cold rolled steel block machined to correspond with the cone angle and allows insertion of steel tubes of different diam. On 16 in. machines a 1 ¾ in. ID vertical discharge pipe is used. Provision is made for attaching a curved section of the same diam to the vertical pipe, to which, in turn, different lengths of horizontal pipe can be connected. Curved Pipe Advantageous It has been found that a curved pipe offers resistance to discharged material flow. In addition, the rotary motion of the underflow can be easily arrested in a curved pipe. Impeller speed of the 16 in. diam machine is provided from 400 to 800 rpm. A speed of about 474 rpm is suitable for maintenance of a constant underflow in coal slurry. In one installation 5x ¼ in. coal is cleaned in a Jeffrey Baum type washer at a 225 tons per hr rate. Washer installation is of the conventional type and a drag type sludge tank is used for water clarification purposes. Capacity of the water system, including the Baum washer, is about 40,000 gal. Before placing the stream-cleaner in operation, it was necessary to flush out the entire system every five days of two shift operations. The only time the system is drained now is for repair work on the sludge conveyor or the rig. The suction line of the stream-cleaner pump terminates in a number of small branch lines located at a depth of about 4 ft above the sludge conveyor. Each branch line extends the full width of the tank and is provided with four intake ports, each one with a funnel shaped inlet projecting downward. The arrangement provides an extensive pick-up area, for dirty water, and the inlets are arranged for a low rim velocity, preventing the taking in of coarse particles. The funnels are also arranged to extend up or down in the tank. They are set to pick up -60 mesh material exclusively.' The material is a high ash and high sulphur product and thus has to be disposed in the refuse conveyor. The underflow of the stream-cleaner is discharged on top of the washery refuse which is carried in a drag type horizontal conveyor, discharging into another refuse conveyor inclined at 30º with a short horizontal loading section. Some Disadvantages The impeller inherits certain disadvantages because of the nature of its construction. Additional moving parts make it subject to wear and maintenance costs. The advantage of being able to maintain a constant speed, however, to produce desired water velocity in the machine outweighs the drawbacks. Better separation between water and solids can be obtained by regulating time of residence of water through adjustment of valves in the intake and discharge lines. The amount of fines encountered during plant operation will vary because of higher or lower moisture in coal passing over fine coal vibrating screens. Even the amount of fines picked up by underground loading machines will be inconstant. Consequently, the percentage of solids will vary in water to be processed. The velocity in the feedlines to the slurry thickeners will fluctuate, with the required water velocity lacking. Another advantage advanced for the machine is its ability to operate on 15 to 25 lb line pressures at the water intake, reducing pump power required and pump maintenance.

Jan 1, 1952

Aaby, Alton O , (S'47) Univ of Minnesota, Mimeapolis, Minn Aaby, Waldo S , (S?48) Univ of Minnesota, Minneapolis Minn Aalde, Kaare, (S'48) Univ of Nevada, Reno, Nev Aaring, Floyd D , (S'48) Univ of Oklahoma, Nor man, Oka Aaronson, Hubert I , (S'47) Carnegie Inst of Technology, Pittsburgh, Pa Abbott, Peyton Osborn, (S'46) 1502 Westover, Austin 21, Texas Abel, Malcolm D , (S'47) Univ of Texas, Austin, Texas Aberg, Richard S , (S'47) Univ of Minnesota, Minneipolis, Minn Abrahamson, Guy C , (S'43) 420 W Dennis St , Wilmington, Calif Abrahao, Benjamin, (S'46) Escola Politeenica da Unnersidade, de Sin Piulo, Braizil Achter, Meyer R , (S'46) Carnegie Inst of Tech , Pittsburgh, Pa

Jan 1, 1952

By E. W. Wagy

The year 1927 witnessed numerous developments of significance in California. The State's shut-in production increased from an average of 58,000 bbl. daily in January to a maximum of 93,000 bbl. daily in August, and a total of about 25,000,000 bbl. was withheld from the market during the year. This not only lessened the effect of large production at Hunt-ington Beach, Seal Beach and Alamitos Heights, but also was a most effective conservation move. Since 1922, it is estimated that approximately 100,000,000 bbl. of oil that would otherwise have been produced have been held in the ground. I. Outstanding Field Developments of 19271 1. Long Beach Deep Sand. 2. Rincon (Seac1iff)Discovery. 3. Alamitos Heights Discovery. 4. Ventura Avenue Extension. 5. Round Mountain Discovery. 6. Mt. Poso Extension. 7. Potrero (Cypress) Discovery. 8. Buttonwillow Gas Development. 9. Goleta Discovery. 10. Union Avenue, Edison and Fruitvale Areas. (See Fig. 1.) II. Crude Production The most important factor in new crude production in 1927 was the Seal Reach field with its adjacent Alamitos Heights townlot area. Production increased from about 10,000 bbl. daily in January, to a peak of 66,000 bbl. in June. Huntington Beach finished the year 1926 with a production of 102,000 bbl. daily, which declined to 60,000 bbl. by the end of 1927. Due to production in these three areas and the tempering effect of shutting in numerous wells, the California production curve for 1927 was held at a fairly even level. Fig. 2, shows the State's production in 1927 and 1926 as compared with 1923, which was the year of excessive

Jan 1, 1928

By H. J. Rose

The peak of production from the Appalachian natural gas field was apparently reached about 10 years ago, and the annual production from Pennsylvania, West Virginia and Ohio has now dropped to about two-thirds of the amounts obtained in 1916 and 1917. This falling off in production has occurred in spite of vigorous efforts and large expenditures by producing companies to maintain or increase their output. The greatly increased costs of development and handling are reflected in the present average value of natural gas at the point of consumption, which value in the three states referred to has more than doubled in the past 10 years. While it is true that the natural gas production of the United States has increased during recent years, this increase has come from southwestern states, particularly from Oklahoma, California, Louisiana and Texas, which states are now leaders in the production of this valuable but fleeting resource. Pennsylvania, originally the leading state in natural gas production, occupies sixth place in the latest (1924) U. S. Bureau of Mines statistics. West Virginia, which held first place for 15 years, has dropped to third rank, and Ohio is the seventh state in the order of natural gas production. Domestic and industrial demands for gas are constantly increasing everywhere in the United States. These growing demands have accentuated the difficulties in the localities with depleted natural gas supplies, and serious shortages have already occurred during winter months in the Pittsburgh district. Some relief has been obtained by placing restrictions on the industrial use of natural gas, and by increasing the price (which tends to reduce consumption). Yet these are but temporary expedients for checking gas consumption, which fail to solve the problem of adequate future supplies of gas. Gas is an exceedingly valuable and important form of fuel, and serious restrictions on its use cannot be tolerated for long in any community. As the supply of natural gas declines, it must be supplemented and eventually replaced with some form of manufactured gas. Many cities, including Pittsburgh, are already supplementing their natural gas supply with the manufactured product.

Jan 1, 1930

By H. F. Yancey, M. R. Geer, C. L. Allyn, R. H. Eckhouse

W. M. Bertholf—This is an excellent report of a well-conducted investigation, of sufficient scope to provide generally useful information. Some years ago we had occasion to test the Humphreys spiral on the middling from our table plant. The conclusions reached in this investigation come as no surprise to us. In certain applications it is virtually impossible to improve on the spiral from the monetary returns point of view even though its "efficiency" may be low. We have noted that in all successful applications of the spiral the feed is "classified," hence we were somewhat disappointed in the showing the spiral made on the Poplar Ridge coal, the only one of the four which could really be considered the equivalent of a classified feed. As was noted in the paper, however, this coal contained a considerable amount of middle and high-gravity material, apparently more than enough to make up for the theoretical advantage of small particles in these categories. A comparison of particle size in the various specific gravity classes of the four coals is given in table XXV. Table XXV. Comparison of Particle Size in Various Specific Gravity Classes. (Unit size, 150 m to 0.105 mm) Black Eagle Clements Poplar Ridge Rosly,n 1.3 Float 7.47 10.60 8.68 9.66 1.3 x 1.4 7.89 7.96 7.58 8.20 1.4x1.6 7.24 8.36 5.58 6.85 1.6 x 1.8 7.98 8.31 3.42 7.33 Sink 1.8 7.85 7.13 5.09 7.41 Avg 7.69 10.08 7.15 8.38 This tabulation indicates that there was very little difference in the size of the various gravity fractions for three of the coals, Poplar Ridge varying the most. Examination of figs. 3, 6, 7, and 8 reveals a general similarity of behavior for all coals except Black Eagle. Would the authors care to speculate on the reasons for the difference in the distribution curve for the sink 1.60 material in the washed coal of fig. 3 as compared to the others? This difference is particularly noticeable in the 8xl4-mesh size. Was there a "shape effect"? J. D. Price and W. M. Bertholf—The performance data on three of the coals studied appear to be typical, but there are certain departures from the general pattern in the case of the Poplar Ridge coal which are large enough to deserve special consideration. For example: 1. Despite the high proportion of sink 1.60 material in the feed, it was not possible to make a corresponding proportion of high-ash reject. (See table XVI.) 2. Even though approximately 70 pct of the feed was 1.40 float with an ash content of 6.6 pct, and this

Jan 1, 1951

By R. H. Eckhouse, M. R. Geer, H. F. Yancey, C. L. Allyn

W. M. Bertholf—This is an excellent report of a well-conducted investigation, of sufficient scope to provide generally useful information. Some years ago we had occasion to test the Humphreys spiral on the middling from our table plant. The conclusions reached in this investigation come as no surprise to us. In certain applications it is virtually impossible to improve on the spiral from the monetary returns point of view even though its "efficiency" may be low. We have noted that in all successful applications of the spiral the feed is "classified," hence we were somewhat disappointed in the showing the spiral made on the Poplar Ridge coal, the only one of the four which could really be considered the equivalent of a classified feed. As was noted in the paper, however, this coal contained a considerable amount of middle and high-gravity material, apparently more than enough to make up for the theoretical advantage of small particles in these categories. A comparison of particle size in the various specific gravity classes of the four coals is given in table XXV. Table XXV. Comparison of Particle Size in Various Specific Gravity Classes. (Unit size, 150 m to 0.105 mm) Black Eagle Clements Poplar Ridge Rosly,n 1.3 Float 7.47 10.60 8.68 9.66 1.3 x 1.4 7.89 7.96 7.58 8.20 1.4x1.6 7.24 8.36 5.58 6.85 1.6 x 1.8 7.98 8.31 3.42 7.33 Sink 1.8 7.85 7.13 5.09 7.41 Avg 7.69 10.08 7.15 8.38 This tabulation indicates that there was very little difference in the size of the various gravity fractions for three of the coals, Poplar Ridge varying the most. Examination of figs. 3, 6, 7, and 8 reveals a general similarity of behavior for all coals except Black Eagle. Would the authors care to speculate on the reasons for the difference in the distribution curve for the sink 1.60 material in the washed coal of fig. 3 as compared to the others? This difference is particularly noticeable in the 8xl4-mesh size. Was there a "shape effect"? J. D. Price and W. M. Bertholf—The performance data on three of the coals studied appear to be typical, but there are certain departures from the general pattern in the case of the Poplar Ridge coal which are large enough to deserve special consideration. For example: 1. Despite the high proportion of sink 1.60 material in the feed, it was not possible to make a corresponding proportion of high-ash reject. (See table XVI.) 2. Even though approximately 70 pct of the feed was 1.40 float with an ash content of 6.6 pct, and this

Jan 1, 1951

By C. M. Young

The safety lamp is the most common and convenient apparatus for detecting inflammable gases in mines, the presence of gas being shown by a blue flame, called the cap, if the wick has been lowered to suppress the luminous flame. The height of the cap increases with the proportion of gas and with the temperature of the lamp flame. Lamps of the Wolf type, the fuel of which is benzine, have a hotter flame than lamps in which vegetable oils are used, such as the Davy, and the Clanny, and are more sensitive than the latter and their many modifications. The Piehler alcohol lamp gives a still higher cap while the Clowes hydrogen lamp is most sensitive of all. While the effect of the temperature of the source of ignition is well known, the writer knows of no previous attempt to correlate the change of this temperature with change of the height of the cap produced, In order to determine the height of the cap at various temperatures, it was necessary to have a source of ignition the temperature of which could be accurately controlled over a considerable range. This condition was met by a coil of wire of high fusing point heated by an electric current controlled by a variable resistance. The use of a coil offered the further advantage of freedom from complications due to the flame of a burning fuel. Such a flame, being itself of variable height, would to some extent raise or lower the elevation of the base of the cap and therefore add to the difficulty of determining the height of the cap. Besides this, the presence of a small cap from the lamp fuel, commonly known as the "fuel cap," would interfere with the observation of small gas caps. After some experiment, a coil was made of platinum wire, No. 26, diameter 0.016 in. The coil was 17/64 in. (6.746 mm.) in outside diameter and had eight full turns in a length of 1/2 in. (12.69 mm.). This was connected to an electric circuit through an adjustable resistance, as shown in Fig. 1. In order to measure the temperature, a thermocouple was inserted in the center of the coil; the leads passed out at the ends and were ccnducted to a millivoltmeter. It is probable that the current of air passing upward through the coil resulted in the indication of a tempera-

Jan 1, 1920

By Virgil Miller, F. B. Petermann, S. F. Ravitz

The Cle Elum nickeliferous iron deposit is in Kittitas County, Washington, in a rugged, mountainous region about 23 miles north of the town of Cle Elum. The Biewett Pass deposit, which is similar in character and occurrence, is in Chelan County, about 18 miles east of the Cle Elum deposit. A more or less continuous ore zone may extend between the two deposits, since iron ore is reported to have been discovered at Iron Mountain, which lies directly between them. The ore probably was formed by meta-morphism of laterite resulting from Ieach-ing of serpentine derived from peridotite. It consists largely of magnetite grains distributed through a matrix of limonitic material containing a small amount of hematite and chromite. Many of the chromite grains have shells and inclusions of magnetite. The magnetite grains range in size from 1200-mesh to 1/4-in., the average size being 48 to 65-mesh; the chromite grains range from 20 to 150-mesh. The gangue minerals are olivine and serpentine with a small, amount of chlorite, and appear both as very thin bands in the ore and 's minute fragments in the limonitic matrix. The nickel is present as minUte inclusions of a nickel silicate mineral within the magnetite and gangue par- ticles, varying in size from 1500 to about 280-mesh. Detailed analyses of 3000-lb. lots of Cle Elum and Blewett Pass ore are given in Table I. TABLE i.—Analyses of Ore Samples Per Cent Ore from Constituent cle Elum' Blewett Pass Cr....................... 2.23 2-12 Ni...................... 1.43 0.9s Fe...................... 52.9 41.4 SiOz.................... 5.6 13.4 CaO.................... 0.3 0.8 MgO................... 4-1 7-5 AI2O3................... 7.0 2.g P...................... 0.022 0.034 S....................... O.O1 o.oa Mn..................... I.I 0.4 Ba..................... nil co..................... o.oa 0.02 CU..................... 0.02 0.03 As...................... 0.03 Au..................... nil Ag°..................... O.58 Pt...................... ml Fe++.................... 8.9 5-9 Fe+++.................. 44-0 35-5 « Ounces per ton, 1 sr,cte,so,","&&$ally absent: B, W, M~, T~, V, ~i, Bi, Pb. Sb. Sn. Be, In, Hg. Zn, Zr. Cd. Preliminary Tests Attempts to beneficiate the ore by ore-dressing methods, including various 'cornbinations of sink and float, tabling, jigging, flotation, and magnetic separation, were consistently unsuccessful. A wide variety of roasting and leaching tests were made on both raw and reduced ore, but in most of the tests little or no nickel was extracted, and in none did the extraction exceed 50 Per cent. No nickel could be volatilized as the carbonyl. by treating reduced ore with carbon monoxide. Fairly good sepa-

Jan 1, 1944

By Howard Eavenson

SOME time ago, in a conference considering the mechanizing of a group of mines, I was asked if I knew of any data showing the relative frequency of accidents due to the use of 275 or 550-volt current inside mines and having a recollection of seeing some in print, the answer was made that I would find what was available. Subsequent search failed to find any pub-lished records of any kind giving such figures and none of the compensation agencies of whom inquiry was made were able to supply any, excepting the Pennsyl-vania Compensation Rating and Inspection Bureau, which had some data covering a few months for some companies in that State. The inquiry was confined to the three largest producing States, Pennsylvania, West Virginia, and Illinois. The inspection departments of neither of the first two had any such records, and in Illinois, only 275 volts has been allowed inside the mines for many years. A laborious inquiry has resulted in the data, shown in Table 1, which on this account was confined to the years 1921 and 1925, the latter being the latest figures available. In each State, to find the mines using 275 and 550-volt current respectively, it was necessary to list the mines from the Coal Catalog, and then to complete the list by inquiries from the companies directly, from Operators' Associations and from Inspection Depart-ments. As the mines not electrified, and those using

Jan 5, 1928

The following is a, partial list of members and guests who called at Institute headquarters during the period Aug. 10, 1917, to Sept. 10, 1917. L. P. Barrett, Ann Arbor, Mich. Milo W. Krejci, Great Falls, Mont. H. J. Brown, Ridley Park, Pa. Chas. N. La Porte, Peoria, Ill. George M. Cheney, Guayaquil, Ecuador. Askin Nicholas, Bismuth, Australia. W. Lorrain Cook, Chicago, Ill. C. Edwin Nighman, Butte, Mont. John J. Croston, Atlanta, Ga. W. L. Remick, Norfolk, Va. A. F. Duggleby, Santiago de Cuba. T. C. Roberts, Jerome, Ariz. Geo. A. Easley, La Paz, Bolivia. Burr A. Robinson, New Haven, Conn. Burr J. French, Magdalena, Jal., Mex. J. L. Schueler, Peoria, Ill. A. D. R. Galloway, Komfrodua, W. Af. Walter L. Steele, Van Horn, Tex. P. R. Hines, Milwaukee, Wis. F. J. S. Sur, Denver, Colo. T. H. Jenks, Wickenburg, Ariz. C. A. Thomas, Dawson, Y. T., Canada. Paul S. King, Wilmington, Del. E. E. White, Ann Arbor, Mich. Harry Wolf, Golden, Colo. L. W. Bahney has left the Sheffield Scientific School, Yale, to become metallurgical engineer with the Scovill Manufacturing Co., Waterbury, Conn. H. B. Barling, formerly chief engineer of Breitung & Co., of New York, has been appointed manager of the mining department.

Jan 10, 1917

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Experienced mining. engineer, Columbia School of Mines graduate, practical experience in drifting, shaft sinking and development work, also in mining, operating and equipping iron, copper, and zinc properties. Married, age 32, available at once. Open for position as superintendent or assistant. No. 462. Member, age 33, married, desires position as mining engineer or engineering executive.- Twelve years experience as mining engineer, geologist, and chief engineer of iron and copper properties. Experience in United States, Mexico and South America. Fluent Spanish. Technical graduate. Minimum salary $3000. No. 466. Member, technical, general superintendent and mill superintendent: Well experienced in latest methods of ore reduction, especially on copper and complex ores. Draft exempt. Not less than $250 per month considered. No. 469. Consulting mining geologist, member of Geological Society of America and A. I. M. E., Professor of Geology and Mineralogy, Lawrence College, desires temporary position during summer in mine surveying, mining methods, expert mine valuation or any exploration work or mine development. Applicant has had nearly three years' experience in gold mining in Mexico and many years professional mine examination work in all regions of Western U. S. Terms reasonable. No. 470. Member, mining engineer, age 46, desires engagement as manager of mining properties, coal or metal mines. Education and 25 years experience in all branches of mining. Have been successful with labor in the management of large properties. No. 471.

Jan 8, 1918