Search Documents

By J. A. Rowland, C. W. Funk

THIS investigation is a part of the United States Bureau of Mines work in conserving the Nation's resources. The isothermal sections presented were developed as a guide to a comprehensive investigation of the properties and fabricating characteristics of copper-base alloys containing manganese and tin. These alloys are being investigated as possible replacements for the commercial bronzes containing substantial quantities of tin. Development of the isothermal sections has, therefore, been limited to the area between 0 to 20 pct Mn and 0 to 25 pct Sn. Since Heusler1 reported the ferromagnetic properties of the Cu-Mn-Sn alloys in 1903, the system has been the subject of several investigations. These studies were largely concerned with correlation of magnetic properties and crystal structure.2-6 Vero,' however, established the solidus surface of the system, between 20 pct Mn and 40 pct Sn, by thermal and microscopic methods. The a, ß, and y solid solutions were also observed by Vero and reported to extend into the interior of the ternary system. For the present study, the annotated diagram of the Cu-Sn system prepared by Raynor' and the Cu-Mn diagram by Dean and coworkers9 were used as the binary borders of the ternary system. Procedure The metals used in this investigation were electrolytic manganese, washed cathode copper, and three-star tin. The manganese, produced at the Boulder City pilot plant of the Bureau of Mines, had a purity of 99.9 pct; the copper contained less than 0.004 pct Bi and 0.001 pct S; the tin contained 0.070 pct Pb, 0.070 pct Sb, 0.050 pct Fe, and 0.065 pct Si. Heats of 1 lb were melted in alundum crucibles with a 3-kw induction furnace. The heats were chill-cast in iron or copper molds to form 6-in. ingots 3/4 in. in diameter. Molds were washed with graphite or zirconia, depending on the manganese content, and preheated to 150°C. The maximum impurity content of any alloy was 0.03 pct Fe, 0.02 pct Si, and 0.02 pct Al; in most cases, they contained less than half this quantity of any of these impurities. Composition of the alloys and their treatment prior to homogenizing are shown in Fig. 1. Designations adjacent to each composition refer to the heat numbers. With a few exceptions, ingots containing 20 pct Sn or less were hot-swaged. These ingots were swaged, after a 24-hr preheat at 650°C, to obtain a total reduction of 70 pct in cross section. Intermittent reheating was necessary, and reductions were limited to either 0.025 or 0.050 in. in diameter per pass. Selection of a 200-hr homogenizing treatment was based on extensive experiments which indicated that virtual equilibrium was reached after 150 hr. Structures were retained by quenching in water. Grain sizes in the specimens homogenized at 350" and 450°C were generally small. These homogenizing treatments were preceded by a 50-hr anneal at 650°C to facilitate phase identification by increasing the grain size in these specimens. The specimens were furnace-cooled from this temperature to the homogenizing temperature, and the heat treatment was continued for the standard 200-hr period. The homogenized samples were bisected to provide an internal section for metallographic examination. Optimum definition of the microstructure was obtained by successive polishing and etching. Quarter-strength ASTM copper reagent No. 13 gave the most satisfactory results.10 Filings from interior sections of the samples were used for diffraction studies. These filings were annealed in evacuated glass tubes at homogenizing temperatures for periods exceeding 50 hr and quenched in water. During this treatment the manganese content was reduced by significant amounts, probably by vaporization. This change in composition was considered in applying the diffraction data, which were used only as a means of identifying phases where the data were consistent with the metallographic evidence. Phase Identification The a solid solution is readily distinguished by the copper-colored, twinned, polyhedral grains, as shown in Fig. 2, and a face-centered cubic X-ray pattern. Tukon indentations, using a 25-g load, indicate a Knoop hardness of 155 for a quenched from 650°C. Using white light developed by a Wratten 78 A filter, the ß grains in etched specimens have a dark brown tint in contrast to the lighter copper-colored grains of the a phase. Knoop hardness values of 284 were obtained for the ß structure in specimens quenched from 650°C. The ß structure was also distinguished from the a phase by its body-centered cubic lattice. The acicular structure appearing in Fig. 3 was evident in several alloys of higher tin content after quenching from either 750' or 650°C. Since a trans-

Jan 1, 1954

By T. F. Witherbee

Discussion of Mr. Baker's paper, read at the Lake Superior Meeting, September, 1904. MR. T. F. WITHERBEE, Durango, Mexico (communication to the Secretary*) : Mr. Baker's paper is very instructive in that it shows how furnace-derangements sometimes originate from apparently slight causes. In 1896 a similar burning through of the lining occurred at the Mayville furnace of the Northwestern Iron Co., Mayville, Wis., in exactly 38 days from the time the furnace was blown in. At that time I attributed it to the fact that the bell was carried several inches to the front side of the furnace, the length of the versed side of the arc described by the lever, thus dumping a little more of the charge on the back side, which made the front side of the furnace-charge more open and consequently increased the circulation of the furnace gases through it. After reading Mr. Baker's description, I believe that possibly a little more ore was charged on the back side of the hopper, due to the fact that it was nearest to the elevator. This unequal charging, however, was unconsciously done, as the fillers were both honest and faithful. The illustration of the burned lining of Furnace No. 1, given in Fig. - of Mr. Baker's paper answers very well for the Mayville furnace. It shows that in both cases the destruction of the lining was largely due to faulty construction, in that there were no cooling-plates in the angle of the bosh and in one or two courses of brick above it, where I believe they are-more in demand than anywhere else in the furnace. The presence of these cooling-plates at the angle of the bosh would have obliged the current of the hot gases to turn the corner and would have prevented them from following the angle of the bosh com¬pletely through the lining and shell.

Mar 1, 1905

By Bunting S. Crocker

PEBBLE grinding at Lake Shore is not a temporary wartime substitute. The tube milling plant, with a 1000 ton per day capacity, grinds a hard siliceous ore to 90 pct - 325 mesh. The plant, prior to using pebbles, was consuming 4.3 lb of 1 1/4-in. grinding balls per ton of ore, which amounted to 785 tons of balls per year. At September 1951 prices, $132.60 per ton, this steel cost amounted to, $104,400 per year, or $0.285 per ton milled. By the Lake Shore method of substituting screened rock for this steel, all of this cost is saved. This is one of the major economies in Lake Shore mill practice. Regardless of the ultimate price of grinding balls, a change, back to steel balls is not considered. The present pebble plant is more flexible than a steel ball plant and equally efficient. For example, if it is desired to change the size of grinding media, the pebble charge in any mill can be changed completely in 4 to 5 days, as against 76 days to change completely a 1 1/4-in. steel ball charge. To change pebble size it is necessary only to change two sets-of screens and clean out the rock feed storage bin. This will take 8 to 10 days as against 3 to 4 months to clean. out the customary supply of grinding balls kept on hand. Also it has not always been ' possible to purchase all desired sizes of balls at any price. In an analysis of savings effected by the use of the pebble mills, the flexibility of the Lake Shore grinding plant should be discussed, as it has a direct bearing on these savings. The plant has always used several units to handle tonnage rather than sending all the tonnage through a single unit. This principle may result in using small diameter mills, but no objection to that is seen. At no time has any advantage been found in cost per ton ground in large diameter mills. Both the capacity and the power of any mill varies as the diameter raised to the 2.6th power. Consequently large or small mills are equally efficient, and a plant should be designed to use as many units-or combination of units as is consistent with reasonable operating practice. Mills under 5 ft diam are harder to reline, etc. To define the case at Lake Shore, .2600 tons per day formerly were milled in seven 7x6-ft ball mills and twelve 5x16-ft (and two 6x16-ft) tube mills.* This gave an excellent test plant. and an extremely efficient-one. In this plant the ratio of ball mills to tube mills was 1: 2. When the much cheaper pebble mills were substituted for the tube mills, this. ratio -was changed to one ball mill to four pebble mills to take the greatest possible advantage of the cheaper operating mill, i.e., the pebble mill. This flexibility without loss in efficiency has been an important item in the cost savings. It is interesting to note that the use of pebbles for fine grinding was. proved first in the laboratory in a 12-in. ball mill. In fact, since 1934 all testing on -.8 mesh material has been done in this 12-in. mill. Scope of the Tests A paper on fine grinding at Lake Shore Mines was published in July 1940.1 This paper covered 7 years of intensive research on fine grinding as well as sizing methods and equipment, plant scale grinding tests on 5x16-ft tube mills with and without .grate discharges-both with 1 1/4-in. and 3/4-in. balls, the use of laboratory mills to evaluate plant changes, and several reports on classifiers and classification. In the following July the addendum report' was added in which the idea of series-circuit grinding was introduced, and the results of running five stages of tube mills and bowl classifiers were shown. Since 1940, the ball milling end of the plant has been altered extensively as a result of tests on the use of 3 1/2-in. rods in 7x6-ft mills and the use of the Tyler repulping screen with from 7 to 14 mesh screens. These tests are, lengthy and may be covered in a separate 'report later. The scope of this report is confined to ore ground by rod milling and ball milling until it passed through an 8 mesh Tyler Ty-rod screen. The -8 mesh screen undersize then was pumped to a primary bowl classifier in open circuit and the sands .from the bowl sent to the primary pebble mills, see Fig: 1. In the pebble mill circuit the ore is ground to 90 pct -325 mesh (24 pct + 28 microns) In studying the flowsheet, attention should be paid to the efficiency of the classification equipment used. The Tyler repulping screen is an efficient machine on the 8 to 10 mesh separation, and the bowl classifier is equally efficient at the 325 mesh separation. Efficient classification is a necessity for series-circuit stage grinding. The ore is hard siliceous porphyry, 60 pct SiO2, 80 pct insoluble. Its grindability at different. meshes has been shown near the top of 'the list in F. C. Bond's grindability tests' Lake Shore is not shown, but an adjacent-mine with identical ore, Wright-Hargreaves, is. Reasons for the-Changeover Since 1936 grinding balls have been rising steadily in price with no sign of stopping. For a mill that used 4.5 to 5.2 lb of grinding balls for every ton of ore ground this rise represented an alarming increase in grinding costs. In many cases the quality of the grinding balls fell off as the scrap steel became more difficult to obtain. The ratio of tube mills to ball mills increased with the use of the Tyler repulping screen in the ball mill circuit. Originally only 3.0 lb of balls per ton were used in the tube mills, and this

Jan 1, 1952

By R. M. Hudson, P. E. Perry

Weight-gain data obtained by nitriding low-carbon sheet steel in an amrnonia CNH,) atmosphere indicated that the process obeyed a parabolic rate law. The calculated actization energy for nitriding in the range 964" to 1268°F agreed reasonably well with published data. At 1358"F, rate data indicated that the activation energy decreased. Weight-gain data obtained by uszng mixtures of NH3 -Nz at 1268°F containzng jrom 10 to 100 zol pct NH3 also obeyed a parabolic rate law. The rate of 'nitriding increased with an increase in the NH3 content of the gas Mixture. It is well-known that steel heated in gas mixtures containing ammonia (NH3) takes up much larger quantities of nitrogen than steel heated in nitrogen, both gases having a total pressure of 1 atm;' this phenomenon can presumably be attributed to the catalytic decomposition of NH3 on the steel surface to furnish nascent (monatomic) nitrogen. This process was studied bv Brunauer. Jefferson, Emmett, and Hend-ricks at furnace temperatures of 752" and 831°F2 using mixtures of NH3 in Hz. Englehardt and wagner3 reported that, at a furnace temperature of 914°F and under their experimental conditions, both nitriding and denitriding were controlled by the rate of gas-metal reactions at a steel surface rather than by the rate of diffusion of nitrogen in iron. The present study was undertaken to obtain information on the kinetics of nitriding low-carbon steel strip at higher temperatures so that practical rates for short-time strip-annealing treatments could be estimated. Variables studied included time: temperature, and NH, content in the annealing atmosphere. Mechanical and chemical characteristics of steel nitrided in this manner will not be considered in the present article. MATERIALS AND EXPERIMENTAL WORK The samples used were from a commercial low-carbon steel, 0.0244 cm thick, in the cold-reduced condition. The chemical composition of this steel is given in Table I. Panels were cut to 5.1 by 17.8 cm, degreased in toluene, and weighed just before treatment. Four specimens were nitrided under each of the experimental conditions. A study was made of the nitriding rate of steel in a 100 vol pct ammonia atmosphere, 740 mm pressure, at five specific temperatures within the range 964" to 1358°F. The nitriding rates of steel in ammonia-nitrogen gas mixtures containing 10, 18, 26, 50, and 100 vol pct ammonia, 740 mm total pressure, at 1268°F were also determined. All atmospheres used were dried by successively passing them through drying towers packed with soda lime and with Linde Molecular sieve Type 4A. Quoted gas compositions refer to those entering the furnace. Specimens were held in the constant-temperature zone of a vertical annealing tube furnace for times of 14, 3, 5, 10, or 15 min. Gas flow rates were maintained at 3.8 cu ft per hr, which was nineteen volume changes per hour for the system used. The rate of flow was selected to provide a high level of free NH3 for cracking on the steel surface where the ammonia gas is most effectively used as a nitriding agent. The vertical annealing tube furnace consisted of a Hevi-Duty tube furnace with a 2 1/2-in.-ID mullite ceramic high-temperature tube. The constant-temperature zone (controlled within 10°F) was about 10 in. long. After each specimen was degreased, a hole was punched in one end, for attaching the specimen by hook to a chain so that it could be lowered into or raised from the high-temperature portion of the tube by means of a power-driven winch. A stainless-steel access port with O-ring seals was connected by suitable glass-to-metal seals to the cool upper portion of the furnace tube. After the weighed specimen was placed in the access port, the furnace tube was evacuated to approximately 10"3 torr, and then the system was flushed thoroughly with the atmosphere under study. When the gas flow rate and constant-temperature zone of the furnace were established, the specimen was lowered into the constant-temperature zone. The atmosphere flowed from the top to the bottom of the vertical furnace tube and was then vented. For all these runs, during the first 3 min of the time the specimen was in the constant-temperature zone of the furnace the specimen was heating up to the tempera-

Jan 1, 1970

By Bunting S. Crocker

EBBLE grinding at Lake Shore is not a temporary BlE wartime substitute. The tube milling plant, with a 1000 ton per day capacity, grinds a hard siliceous ore to 90 pct — 325 mesh. The plant, prior to using pebbles, was consuming 4.3 lb of 11/4-in. grinding balls per ton of ore, which amounted to 785 tons of balls per year. At September 1951 prices, $132.60 per ton, this steel cost amounted to $104,400 per year, or $0.285 per ton milled. By the Lake Shore method of substituting screened rock for this steel, all of this cost is saved. This is one of the major economies in Lake Shore mill practice. Regardless of the ultimate price of grinding balls, a change back to steel balls is not considered. The present pebble plant is more flexible than a steel ball plant and equally efficient. For example, if it is desired to change the size of grinding media, the pebble charge in any mill can be changed completely in 4 to 5 days, as against 76 days to change completely a 1-in. steel ball charge. To change pebble size it is necessary only to change two sets of screens and clean out the rock feed storage bin. This will take 8 to 10 days as against 3 to 4 months to clean out the customary supply of grinding balls kept on hand. Also it has not always been possible to purchase all desired sizes of balls at any price. In an analysis of savings effected by the use of the pebble mills, the flexibility of the Lake Shore grinding plant should be discussed, as it has a direct bearing on these savings. The plant has always used several units to handle tonnage rather than sending all the tonnage through a single unit. This principle may result in using small diameter mills, but no objection to that is seen. At no time has any advantage been found in cost per ton ground in large diameter mills. Both the capacity and the power of any mill varies as the diameter raised to the 2.6th power. Consequently large or small mills are equally efficient, and a plant, should be designed to use as many units or combination of units as is consistent with reasonable operating practice. Mills under 5 ft diam are harder to reline, etc. To define the case at Lake Shore, 2600 tons per day formerly were milled in seven 7x6-ft ball mills and twelve 5x16-ft (and two 6x16-ft) tube mills.* This gave an excellent test plant and an extremely efficient one. In this plant the ratio of ball mills to tube mills was 1:2. When the much cheaper pebble mills were substituted for the tube mills, this ratio was changed to one ball mill to four pebble mills to take the greatest possible advantage of the cheaper operating mill, i.e., the pebble mill. This flexibility without loss in efficiency has been an important item in the cost savings. It is interesting to note that the use of pebbles for fine grinding was proved first in the laboratory in a 12-in. ball mill. In fact, since 1934 all testing on — 8 mesh material has been done in this 12-in. mill. Scope of the Tests A paper on fine grinding at Lake Shore Mines was published in July 1940.' This paper covered 7 years of intensive research on fine grinding as well as sizing methods and equipment, plant scale grinding tests on 5x16-ft tube mills with and without grate discharges both with 1-in. and -in. balls, the use of laboratory mills to evaluate plant changes, and several reports on classifiers and classification. In the following July the addendum report2 was added in which the idea of series-circuit grinding was introduced, and the results of running five stages of tube mills and bowl classifiers were shown. Since 1940, the ball milling end of the plant has been altered extensively as a result of tests on the use of 3-in. rods in 7x6-ft mills and the use of the Tyler repulping screen with from 7 to 14 mesh screens. These tests are lengthy and may be covered in a separate report later. The scope of this report is confined to ore ground by rod milling and ball milling until it passed through an 8 mesh Tyler Ty-rod screen. The —8 mesh screen undersize then was pumped to a primary bowl classifier in open circuit and the sands from the bowl sent to the primary pebble mills, see Fig. 1. In the pebble mill circuit the ore is ground to 90 pct —325 mesh (24 pct + 28 microns). In studying the flowsheet, attention should be paid to the efficiency of the classification equipment used. The Tyler repulping screen is an efficient machine on the 8 to 10 mesh separation, and the bowl classifier is equally efficient at the 325 mesh separation. Efficient classification is a necessity for series-circuit stage grinding. The ore is hard siliceous porphyry, 60 pct SiO,, 80 pct insoluble. Its grindability at different meshes has been shown near the top of the list in F. C. Bond's grindability tests.' Lake Shore is not shown, but an adjacent mine with identical ore, Wright-Hargreaves, is. Reasons for the Changeover Since 1936 grinding balls have been rising steadily in price with no sign of stopping. For a mill that used 4.5 to 5.2 lb of grinding balls for every ton of ore ground this rise represented an alarming increase in grinding costs. In many cases the quality of the grinding balls fell off as the scrap steel became more difficult to obtain. The ratio of tube mills to ball mills increased with the use of the Tyler repulping screen in the ball mill circuit. Originally only 3.0 lb of balls per ton were used in the tube mills, and this

Jan 1, 1953

By Bunting S. Crocker

EBBLE grinding at Lake Shore is not a temporary BlE wartime substitute. The tube milling plant, with a 1000 ton per day capacity, grinds a hard siliceous ore to 90 pct — 325 mesh. The plant, prior to using pebbles, was consuming 4.3 lb of 11/4-in. grinding balls per ton of ore, which amounted to 785 tons of balls per year. At September 1951 prices, $132.60 per ton, this steel cost amounted to $104,400 per year, or $0.285 per ton milled. By the Lake Shore method of substituting screened rock for this steel, all of this cost is saved. This is one of the major economies in Lake Shore mill practice. Regardless of the ultimate price of grinding balls, a change back to steel balls is not considered. The present pebble plant is more flexible than a steel ball plant and equally efficient. For example, if it is desired to change the size of grinding media, the pebble charge in any mill can be changed completely in 4 to 5 days, as against 76 days to change completely a 1-in. steel ball charge. To change pebble size it is necessary only to change two sets of screens and clean out the rock feed storage bin. This will take 8 to 10 days as against 3 to 4 months to clean out the customary supply of grinding balls kept on hand. Also it has not always been possible to purchase all desired sizes of balls at any price. In an analysis of savings effected by the use of the pebble mills, the flexibility of the Lake Shore grinding plant should be discussed, as it has a direct bearing on these savings. The plant has always used several units to handle tonnage rather than sending all the tonnage through a single unit. This principle may result in using small diameter mills, but no objection to that is seen. At no time has any advantage been found in cost per ton ground in large diameter mills. Both the capacity and the power of any mill varies as the diameter raised to the 2.6th power. Consequently large or small mills are equally efficient, and a plant, should be designed to use as many units or combination of units as is consistent with reasonable operating practice. Mills under 5 ft diam are harder to reline, etc. To define the case at Lake Shore, 2600 tons per day formerly were milled in seven 7x6-ft ball mills and twelve 5x16-ft (and two 6x16-ft) tube mills.* This gave an excellent test plant and an extremely efficient one. In this plant the ratio of ball mills to tube mills was 1:2. When the much cheaper pebble mills were substituted for the tube mills, this ratio was changed to one ball mill to four pebble mills to take the greatest possible advantage of the cheaper operating mill, i.e., the pebble mill. This flexibility without loss in efficiency has been an important item in the cost savings. It is interesting to note that the use of pebbles for fine grinding was proved first in the laboratory in a 12-in. ball mill. In fact, since 1934 all testing on — 8 mesh material has been done in this 12-in. mill. Scope of the Tests A paper on fine grinding at Lake Shore Mines was published in July 1940.' This paper covered 7 years of intensive research on fine grinding as well as sizing methods and equipment, plant scale grinding tests on 5x16-ft tube mills with and without grate discharges both with 1-in. and -in. balls, the use of laboratory mills to evaluate plant changes, and several reports on classifiers and classification. In the following July the addendum report2 was added in which the idea of series-circuit grinding was introduced, and the results of running five stages of tube mills and bowl classifiers were shown. Since 1940, the ball milling end of the plant has been altered extensively as a result of tests on the use of 3-in. rods in 7x6-ft mills and the use of the Tyler repulping screen with from 7 to 14 mesh screens. These tests are lengthy and may be covered in a separate report later. The scope of this report is confined to ore ground by rod milling and ball milling until it passed through an 8 mesh Tyler Ty-rod screen. The —8 mesh screen undersize then was pumped to a primary bowl classifier in open circuit and the sands from the bowl sent to the primary pebble mills, see Fig. 1. In the pebble mill circuit the ore is ground to 90 pct —325 mesh (24 pct + 28 microns). In studying the flowsheet, attention should be paid to the efficiency of the classification equipment used. The Tyler repulping screen is an efficient machine on the 8 to 10 mesh separation, and the bowl classifier is equally efficient at the 325 mesh separation. Efficient classification is a necessity for series-circuit stage grinding. The ore is hard siliceous porphyry, 60 pct SiO,, 80 pct insoluble. Its grindability at different meshes has been shown near the top of the list in F. C. Bond's grindability tests.' Lake Shore is not shown, but an adjacent mine with identical ore, Wright-Hargreaves, is. Reasons for the Changeover Since 1936 grinding balls have been rising steadily in price with no sign of stopping. For a mill that used 4.5 to 5.2 lb of grinding balls for every ton of ore ground this rise represented an alarming increase in grinding costs. In many cases the quality of the grinding balls fell off as the scrap steel became more difficult to obtain. The ratio of tube mills to ball mills increased with the use of the Tyler repulping screen in the ball mill circuit. Originally only 3.0 lb of balls per ton were used in the tube mills, and this

Jan 1, 1953

Joseph G. Butler, Jr., who represented this Institute on the American Industrial Commission to France, has presented a report to the Chairman of the Commission regarding the steel industry of France in war time. In this report Mr. Butler calls attention to the fact that only a few steel works were visited and that he thinks it probable that there are many plants in France more up-to-date than these. He noticed especially in the plants visited a dearth of labor-saving devices and not very great attention to the safety of the employees. He also noticed that the whole of the iron and steel interests in France are being used at the present time by the Government for war purposes, and he was told on good authority that the production has doubled since May, 1915. When the war is over, it is thought that France can send large quantities of iron ore from Algeria to the United States and take in return American coal to France, an interchange which would doubtless be of mutual advantage. In Mr. Butler's opinion the shortage of coal in France may be overcome to some extent by the use of water-power and by electrical processes for steel manufacture, and lie believes when the war ends France will be able to compete with other countries in exports of general iron and steel products, this trade being facilitated by the port improvements at Bordeaux and Marseilles. The French labor situation is much better than that in the United States from the standpoint of labor unions, but the wages are less and many women are now being employed to do men's work. This has a tendency to keep wages low, but is probably a war expedient only. The cooperation among manufacturers in France is at a high level and both local and national organizations exist for the discussion and voicing of trade problems. The national body which is a combination of the individual organizations is the Comite des Forges de France and it is an interesting fact that many of the members of this body are office holders under the Government, or heads of Government Committees which are organized to look after the very business in, which the individuals are engaged.

Jan 12, 1916

By S. M. Marshall, B. M. Bird

For a number of years European investigators have used laboratory methods of predicting the probable strength of coke made from coal, and recently several investigators in the United States have reported the use of various tests for this purpose. There is at present no method accepted as standard, however, nor is there even agreement as to the general type of test that should be used. Furthermore, because the details of most of the tests have not been worked out carefully, one investigator can not hope to duplicate the work of another. The extension of coke manufacture to new localities in the United States, and the increasing need for cokes of exceptional qualities made from the most economical mixtures, made it desirable to have some simple laboratory test which will determine whether given coals, alone or blended with other coals, are more satisfactory from the standpoint of coke strenpth- than others of different cost. The work described herein has resulted in the development of a simple laboratory test which, it is believed, can be generally adopted in coal laborat,ories, and which will give concordant results even though performed by different investigators in different laboratories. The general method of predicting whether a coal or a mixture of coals will produce a strong coke, resistant to crushing and shattering, has been to correlate the known strengths of the cokes produced in commercial ovens with some measurable constituent or with some property of the coals, and then to use the relationship so found for forming an estimate of the coking strengths of coals unknown. Several such correlations have utilized the percentages of the various ultimate constituents of coal, such as the oxygen content and the hydrogen-oxygen ratio;(39)§ other correlations have involved the proportion of a, B and r com-pounds, (17,21,30c) or of "oil and solid bitumens."(16,30) Also a relationship has been traced between the coking properties of coal and the rate of change of the resistance offered to the flow of an inert gas by fine particles of the coal while being slowly heated. (11,176) But the most general corre-

Jan 1, 1930

By R. HAYDEN, H. B. HALLOWELL, H. O. Hofman

THE object of refining copper in the reverberatory furnace is to obtain a metal which will have the highest attainable degree of malleability, ductility and electric conductivity, and present at the same time a level surface when it solidifies in the mold after casting. These desirable physical properties are governed by the character of the impurities and the forms in which they are present, by the amount of cuprous oxide retained by the copper, by the quantity of gas held in solid solution, by the casting-temperature, and by the thickness of the casting. The effects of impurities, of cuprous oxide and of gases upon the mechanical properties of copper have been studied by Hampe in his classical paper "Contributions to the Metallurgy of Copper." The most recent research into the effect of metals upon the electrical conductivity of copper is that of Addicks.2 The influence of cuprous oxide upon the electrical conductivity has been investigated by Walker' and Addicks.4 The absorption of gases has received' attention by Hampe,5 Stahl 6 and Heyn.7 The effects of casting-temperature have been noted by Stahl.8

Mar 1, 1907

By S. Weinig, J. Winter

The grain boundary adsorption of solutes as a function of bulk concentration and solution temperature was studied using internal-frictimz techniques. From the variation of the cor-responding energy of activation for the Phenomenon, the inter-actior2 energy between a solute atom and a high-angle boundary was calculated. Interaction energies in the range of 0.3 ev were obtained, and were used to obtain the actual concentration of solute at the grain boundary. In corroboralory creel, studies the direct grain boundary contribution to the total creep strain was measured. It was found that the interface creep varied with the type and magnitude of the solute adsorbed. Subscribing to the theory of their being energetically favorable sites at the grain boundary for solutes of both Positive and negative size deviations, ternaries were investigated in Which solutes of both types were present. A marked increase in the resistance to grain boundary creep was manifested. THE major difficulty which has been encountered in investigations of the grain boundary segregation of solutes has been the lack of a sufficiently sensitive method of measuring the amount of adsorbed solute at the boundary. For the general case of a high-angle boundary, no direct method of measuring the adsorption at the boundary has been found to date. Internal friction has been used in several studies of grain boundary adsorption1-3 and although it is somewhat indirect, it was demonstrated to have the necessary sensitivity. In this investigation the authors have used internal-friction techniques in conjunction with a study of the grain boundary contribution to the total creep strain. As both parts of the investigation were performed on the same specimens it was possible to combine a highly sensitive technique with a somewhat more direct method in order to obtain information about the adsorption phenomenon. From internal-friction studies the rate of increase of the activation energy was observed to be a function of the difference in size between the solute and solvent atoms. It was proposed that if Gibbs' adsorption isotherm is considered, i.e., where r is the excess solute at the boundary, c is the bulk concentration, and ay/ac is the change in grain boundary energy with bulk concentration, then AH b/ac must vary in the same way as ay/ac and therefore In this way a relative measure of the grain boundary adsorption of solutes is directly obtainable from in-ternal-friction studies. If the previous work in the field of grain boundary adsorption of solutes is examined, certain apparent information is desirable if the phenomenon is to be understood. The most important questions that must be asked are as follows: 1) Is the adsorption of solutes at the grain boundary an equilibrium process? 2) Can the Mott model of the grain boundary be used as a basis of setting up an elastic interaction between the grain boundary and solute atoms? 3) Is it possible to obtain an exact measure of the excess solute at the grain boundary as a function of temperature and bulk concentration rather than merely a relative measure of the adsorption 4) Are the conclusions obtained from an indirect method such as internal-friction studies meaningful in considering gross grain boundary effects such as creep? EXPERIMENTAL PROCEDURE The material used in this investigation was Bureau of Mines "superpurity" titanium (79 Bhn—1500 kg

Jan 1, 1960

record with the Royal Flying Corps was considered a remarkable one, for he was at the front within two months of the date on which he was granted a commission, during which interval he took the prescribed technical course at Oxford, and aviation training at Netheravon and Bristol. On Sept. 14, 1916, he took his first flight over the German lines, when his engine stalled and he had to volplane down, fortunately landing on the French side of the lines. On Sept. 16, he went over the lines with six others, and not returning immediately with the others, was lost. He tried to make for the sea and come back following the course of a river, but when he did descend he found that he was 60 miles west of Paris and 100 miles south of his lines. He flew over to Paris and stayed there for the night, going back to his squadron the next morning. Then on Oct. 4, he was sent up at night for the first time, and in making a landing he passed the flares just as he struck the ground, which put him in total darkness. He struck something and his machine turned a complete somersault, which accident put him in the hospital for ten days. In December, 1916, he left the 21st Squadron and was transferred to the 24th, as the 21st was made an Artillery Squadron and he preferred to remain a fighting scout. In the same month, he was made Acting Flight Commander for about 6 weeks, and about April 3, 1917, his rank of Flight Commander was confirmed. The beginning of May he started to introduce a number of new machines for his squadron, these being of an entirely new type. On May 19, he was up with one of the machines in the evening, practising sharp turns and dives, when the wings suddenly crumpled up and he fell 700 ft., being killed instantly. He was buried in a French Cemetry at Monchy Lagache about 8 miles southeast of Perronne, and about 25 miles east of Amiens. Sergeant Herbert Moore Harbach Herbert Moore Harbach was born in Lebanon, Pa., Apr. 4, 1891, graduated from the Lebanon High School in 1911, and entered State College from which he received his degree of Bachelor of Science in Metallurgical Engineering in 1915. He was employed by the Lackawanna Iron Co., at Buffalo, W. Y., and was later transferred to their Lebanon plant to start up the newly erected benzol plant. He was later made foreman of the coke ovens, which position he held after it was bought by the Bethlehem Steel Co., and until he enlisted in the service of his country in September, 1917. He was stationed at Camp Meade, Md., until the spring of 1918, when he was transferred to the C. W.

Jan 1, 1920

By M. Otogawa

TsunashiRo Wada, honorary member of the Institute, died at his residence, Ushigome, in Tokyo, on Dec. 20, 1920, at the age of sixty-four; he was born on March 15, 1856, at Obana in the province of Wakasa. An expert mineralogist, lithologist and geologist, he identified himself throughout his life with the development of the mining interest of this country. Perhaps the most noteworthy of his meritorious services in the public sense was the extension of the Imperial Steel Works at Yawata, anticipating the grim fate that hurled Japan. into a war with Russia in 1904. Educated in the Imperial University of Tokyo by foreign professors, he studied especially mineralogy, lithology and geology. In 1875 he was appointed assistant professor in the Imperial University of Tokyo, and in 1878 entered the service of the Home Department. From 1880 until 1893, Mr. Wada was Director of the Imperial Geological Survey of Japan, during which time he practically laid the foundation of the geological investigation work in Japan. In 1884, he made a trip to Europe by government order to attend the international Congress in Berlin, visiting en route several countries of Europe and America. While Director of the Survey, he was also, from 1880 to 1885, lecturer, and from 1885 to 1891, professor of mineralogy and lithology in the Imperial University, and, from 1889 to 1893, was Director of the Imperial Mining Bureau of Japan. In this capacity, he revised the mining laws of Japan, thus laying the foundation of Japan's mining administration. In 1894, he was again appointed lecturer in the Imperial University of Tokyo; in 1895, appointed Technical Adviser on Mines to the Imperial Household Department of Japan; and, in 1897, appointed President of the Imperial Steel Works, which was completed in 1900 with the expenditure of $10,000,000. In this capacity he did a great deal to promote the iron and. steel industry of this country. We owe him the ore-purchase contract with the Daiya iron mine in China, which remarkably facilitated the extension of the iron works in later days. The victory of the Russo-Japanese war must be said to be due to his merit in no small measure. He resigned the presidency of the Imperial Steel Works in 1901. In 1899, Mr. Wada visited America and several countries of Europe by government order; in 1902, he traveled through north and middle China doing exploration work and studying the geology of the country, accompanied by mining engineers and geologists. From 1896 to 1908, Mr. Wada was president and honorary member of

Jan 1, 1922

By M. Otogawa

TsunashiRo Wada, honorary member of the Institute, died at his residence, Ushigome, in Tokyo, on Dec. 20, 1920, at the age of sixty-four; he was born on March 15, 1856, at Obana in the province of Wakasa. An expert mineralogist, lithologist and geologist, he identified himself throughout his life with the development of the mining interest of this country. Perhaps the most noteworthy of his meritorious services in the public sense was the extension of the Imperial Steel Works at Yawata, anticipating the grim fate that hurled Japan. into a war with Russia in 1904. Educated in the Imperial University of Tokyo by foreign professors, he studied especially mineralogy, lithology and geology. In 1875 he was appointed assistant professor in the Imperial University of Tokyo, and in 1878 entered the service of the Home Department. From 1880 until 1893, Mr. Wada was Director of the Imperial Geological Survey of Japan, during which time he practically laid the foundation of the geological investigation work in Japan. In 1884, he made a trip to Europe by government order to attend the international Congress in Berlin, visiting en route several countries of Europe and America. While Director of the Survey, he was also, from 1880 to 1885, lecturer, and from 1885 to 1891, professor of mineralogy and lithology in the Imperial University, and, from 1889 to 1893, was Director of the Imperial Mining Bureau of Japan. In this capacity, he revised the mining laws of Japan, thus laying the foundation of Japan's mining administration. In 1894, he was again appointed lecturer in the Imperial University of Tokyo; in 1895, appointed Technical Adviser on Mines to the Imperial Household Department of Japan; and, in 1897, appointed President of the Imperial Steel Works, which was completed in 1900 with the expenditure of $10,000,000. In this capacity he did a great deal to promote the iron and. steel industry of this country. We owe him the ore-purchase contract with the Daiya iron mine in China, which remarkably facilitated the extension of the iron works in later days. The victory of the Russo-Japanese war must be said to be due to his merit in no small measure. He resigned the presidency of the Imperial Steel Works in 1901. In 1899, Mr. Wada visited America and several countries of Europe by government order; in 1902, he traveled through north and middle China doing exploration work and studying the geology of the country, accompanied by mining engineers and geologists. From 1896 to 1908, Mr. Wada was president and honorary member of

Jan 1, 1922

By Robert D. Longyear

IN MOST diamond core drilling the primary objective is the recovery of samples to be used for chemical analysis, physical tests, or visual inspection. Unless these samples are reliable and the information systematically recorded, the time and money spent in securing them are largely wasted. A properly taken diamond-drill sample is similar to a properly moiled channel sample but more accurate. No channel sample can be moiled in as even a groove as the smooth cylinder of material normally removed in diamond drilling. More important still, sampling by the diamond drill practically eliminates that personal equation which Jora1emon4 reference numbers apply to publications listed in the bibliography at the end of this article) has aptly termed "the almost magnetic attraction of the most conscientious hand toward rich pieces of ore."

Jan 1, 1937

By Herbert Clark Hoover, Lou Henry Hoover

QUESTIONS of assaying were explained in the last Book, and I have now come to a greater task, that is, to the description of how we extract the metals. First of all I will explain the method of preparing the ore1 ; for since Nature usually creates metals in an impure state, mixed with earth, stones, and solidified juices, it is necessary to separate most of these impurities from the ores as far as can be, before they are smelted, and therefore I will now describe the methods by which the ores are sorted, broken with hammers, burnt, crushed with stamps, ground into powder, sifted, washed, roasted, and calcineda.

Jan 1, 1950

IRON AND STEEL COMMITTEE ALBERT SAUVEUR, Chairman A. A. STEVENSON, Vice-Chairman HERBERT M. BOYLSTON, Secretary, Abbot Bldg., Cambridge, Mass. Guilliaem Aertsen, Henry M. Howe, E. Gybbon Spilsbury, John Birkinbine, _Robert-W. Hunt, J, S. Unger; William-H. Blauvelt, J:-E: Johnson, Jr., Felix A: Vogel; Charles A. Buck, Charles Kirchhoff, Leonard Waldo, Ernest F. Burchard, Richard Moldenke, William R. Walker, F. D. Carney, Charles F. Rand, William R. Webster, James Gayley, Joseph W. Richards, Frederick W. Wood. Henry D. Hibbard, C. F. W. Rys, There will be a meeting of the Institute in Pittsburg on Oct. 8, 9, and 10, 1914. This meeting will be under the joint auspices of the Iron and Steel Committee, the Committee on Coal and Coke, and the Committee on Petroleum and Gas. The iron and steel papers will probably be presented on Oct. 8. The following papers have been received and accepted and will be read at the October meeting.

Jan 6, 1914

(Members are urged to send in for this column any notes of interest concerning themselves or their. fellow-members.) Members and guests who registered at Institute headquarters during the period Nov. 10 to Dec. 10, 1914: H. F. Grondijs, Oruro, Bolivia. E. B. Kirby, St. Louis, Mo. R. W. Shumway, Denver, Colo. W. R. Webster, Philadelphia, Pa. J. N. Houser, Mascot, Tenn. F. S.. Titsworth, Denver, Colo. F. L. Clerc, Denver, Colo. Frank R. Wicks, Butte, Mont. Robert Sticht, Queenstown, Tasmania. C. Q. Schlereth, Denver, Colo. Francis C. Phillips, Pittsburgh, Pa. Robert Hallowell Richards was given a dinner on December 7 at Boston by the corporation, faculty and alumni of Massachusetts Institute of Technology in recognition of his 50 years as a devoted alumnus and teacher and as an expression of the respect and affection in which he is held.

Jan 1, 1915

By W. J. Taylor

It is, perhaps, more important to put on record the particulars of experiments that are derided failures than those that are successful, as those of the latter class are certain to live, while the former may be lost sight of in a short time, and repeated by others. TO this end, I propose to give the particulars of a straight or no-bosh furnace just tried at the Chester (New Jersey) works, which was such a decided failure as to leave no doubt of the plan being wrong, and determining the necessity of a bosh of some kind, as of old. Some experiences during the past year led me to suppose that the bosh or belly of a furnace was unnecessary, and that the contraction of the walls toward the bottom for the stock to wedge in, in its descent, facilitated dirty walls and scaffolding; hence, irregularity and high fuel. I concluded, however, that a very shallow bosh for a skew-back support to the stock would be necessary, and that the proper place for this was in the tuyere-section, beginning just below the tuyeres and ending just above them, where there is nothing in the solid state but fuel, which is consuming, and no slipping or travel of stock takes place. The cubical capacity of a furnace of this design would necessarily be much less than in the old style, unless it was made very much higher. But I assumed that the loss of room for reduction could be overcome by making the size of the ore and stone charged much smaller, so that the gases would act more quickly. The next point was, what should be the size of the shaft, crucible, tuyere-circle, and tunnel-head for a given quantity of air? My first design was 12 feet diameter of shaft for 7000 feet of air, with a 9-foot crucible and 8-foot toyere-circle. This I soon reduced to 8-foot shaft diameter, which I concluded was large enongh for economical work, if regular travel of the stock on the walls could be maintained. I consulted with a number of experienced furnacemen and furnace-engineers, and the plan was well thought of by many of them; and, as I had also some offers of financial aid from them toward the risk of trying the experiment, my firm concluded

Jan 1, 1885

By Lawrence W. Teufel

A method to determine in situ stress directions and magnitudes from anelastic strain recovery measurements of oriented core has been used to determine the principal horizontal in situ stresses in the Rollins Sandstone in a deep well near Rifle, Colorado. The principal horizontal stress directions were determined directly from the principal horizontal strain recovery directions. The principal horizontal stress magnitudes were calculated from the principal strain recovery magnitudes, overburden stress, and Poison's ratio of the rock using a viscoelastic model. The accuracy of the in situ stress directions and magnitudes determined from anelastic strain recovery measurements was substantiated by a direct comparison with open-hole hydraulic fracture stress measurements. The anelastic strain recovery method predicted the magnitudes of the maximum and minimum horizontal principal stresses to be 54.5 MPa and 51.9 MPa, respectively; with an azimuth of N63ºW ± 8º for the maximum horizontal stress. The hydraulic fracture stress measurements yielded maximum and minimum horizontal principal stress magnitudes of 49.6 MPa and 46.8 MPa, respectively. The azimuth of the maximum horizontal stress ranged from N50ºW to N70°W.

Jan 1, 1984

(Members are urged to send in for this column any notes of. interest concerning themselves or their. fellow-members.) Members and guests who registered at Institute headquarters during the period July 10 to Aug. 10, 1914: W. B. Foote, Geneva, N. Y. John T. Beard, Temascaltepec, Mexico. E. J. Carlyle, Perm, Russia. F. H. Jackson, Alum Rock, Pa.. H. H. Bradt, Pittsburg, Pa. M. F. Sayre, Schenectady, N. Y. Dwight Furness, Guanajuato, Mexico. Prof. Robert H. Richards, past-president of the Institute, has retired as head of the Mining department of Massachusetts Institute of Technology and will engage more actively than formerly as consulting engineer in ore-dressing problems. Luther W. Kemp, who has been Metallurgist of the North Star Mines Co. at Grass Valley, Cal., has resigned to accept a position in Chile,. S. A.

Jan 9, 1914