Search Documents

By J. A. Sekhar

Solidification processing/casting is increasingly being adopted as the preferred manufacturing technique for the fabrication of net shaped complex geometry components. Modeling of solidification processes is important both for design purposes as well as for understanding the physics of morphological evolution of the solidification microstructure. A fundamental aspect of such modeling involves the precise understanding? of heat transfer through the two phase solid/liquid region. A scheme to do this will be presented where the nonlinearity of the fraction liquid with change in temperature can be incorporated into the numerical calculations. The importance of properly accounting for the non-linear mushy zone will be discussed. Typical processes like squeeze casting and electromagnetic stirring will be discussed to illustrate how precise modeling of the solid/liquid region can aid in the calculation of accurate heat transfer coefficients for these processes.

Jan 1, 1990

By Norbert L. Piret

From the copper smelter operation a various outputs are to exert negative impacts on the environment. Particularly, emissions like SO2 and dusts, solid wastes like contaminated gypsum and arsenic sludge, effluents and heated cooling water are generated. Most countries have sitipulated an environmental legislation to provide the framework for an efficient environmental management. As part of the planning activities for x major greenfield copper smelter, the Following elaborations are required and were drawn up. -The Environmental Impact Assessment which is the first step of environmental management and mandatory for every new project. - The Environmental Monitoring Plan, which describes the monitoring procedures for the main impacts identified and assessed. -The Environmental Management Plan, which deals with the minimization of environmental impacts, and the methods of its implementation.

Jan 1, 1996

By Hong Yong Sohn, Miguel Olivas-Martinez

"Different approaches are used for calculating the ‘energy requirement’ of a process. The determination of energy requirement becomes confusing for a process in which a fuel is also a reactant. The key issue is which heat of chemical reaction should be included in the ‘energy requirement’ value. We will use the example of ironmaking processes to illustrate the problem. The different approaches essentially boil down to the question: does one include the combustion heat of the reductant used in the reduction reaction or just the heat of the reduction reaction? Depending on the viewpoint, either approach can be accepted; it is a matter of convention. There is a need, however, to select a standard approach because the absolute value of ‘energy requirement’ of a process depends on the choice. The energy requirement of a novel flash ironmaking process will be compared with that of an average blast furnace operation.IntroductionDifferent approaches are used for performing energy balance calculations and perhaps more significantly in presenting the ‘energy requirement’ of a process. The question becomes more involved for a process in which one or more reactants are also used to generate the process heat by combustion. Often the key issue is which heat of chemical reaction to include in presenting the ‘energy requirement’ of the process.It is worthwhile to note at the outset that the difference in energy requirements between different processes for converting similar raw materials to the same desired product is largely unaffected by the choice of chemical reactions to be included. However, the absolute value presented as the ‘energy requirement’ of a process can be different by a large amount depending on the approach. We use the example of ironmaking processes to illustrate the problem. In these processes, as currently practiced or under development, carbon and/or hydrocarbons (including hydrogen) are used as the fuel as well as the reactant for reducing the iron oxide mineral.The different approaches in this case essentially boil down to the following question: does one include the combustion heat of the reductant used in the reduction reaction or treat the reductant portion as just a reactant? Depending on the viewpoint, either approach can be considered acceptable. It is a matter of convention. There is a need, however, to select a standard approach because the absolute value of ‘energy requirement’ of an ironmaking process (e.g., the currently dominant blast furnace process) depends on such a choice. It is particularly important to clearly state the specific approach used when the energy requirement of ironmaking is compared with those of other industrial processes such as petrochemicals production."

Jan 1, 2014

By Stefan Mutz

In Germany the automobile recycling is regulated by law. Current legislation requires that by the year 2015, eighty five w.-t. % of the components from used cars ill be materially recycled. Whilst for 10 w.-t. % of the materials a thermal utilization is certified, there are still some concrete questions that remain unanswered regarding the usability of single fractions. The recent innovative approaches to the concepts of used cars dismantling do not alter the fact that the majority of the materials of used cars still have to pass over the shredder and the connected processing aggregates. The status of the so called SLF (Shredder light fraction) which is about 25 w.-t. % w.-t. in used cars, has not been satisfactorily clarified. Furthermore questions still remain regarding the separation of the NMSF (nonmagnetic metal shredder fraction) which has to be separated in the single metallic fractions like stainless tell, copper, brass, zinc, etc. Attempts of optimization can be found. This paper analyses some of the difficulties being encountered by the automobile recycling industry in Germany, before reviewing some of the innovative approaches that the industry has introduced. Finally the paper goes on to describe the potential of automatic picking. Examples of a series of tests, utilizing this technology, in which a variety of products from a range of shredders were isolated are described in detail. This new technology provides a range of applications to the automobile recycling industry.

Jan 1, 2002

By Fiseha Tesfaye, Pekka Taskinen

"Thermodynamics of the equilibrium phase assemblage Ago_9Cul.lS-Cu2-xS-CuS have been studied by an EMF -method. The ternary phase was synthesized from the pure Cu2S and Ag2S in vacuum furnace at high-temperature and mixed with appropriate compositions of Cu2S and CuS to form the cathode electrode. The EMF-measurements were made on the solid-state galvanic cell Pt(-) I Ag I RbAg,ils I Ago9Cu1.1S-Cu2-xS-CuS I Pt(+), in a temperature range from 316 K to 498K.Based on the measured EMF vs. T relations, thermodynamic functions (?fG° , ?fS and ?fH°) of stromeyerite (Ag0.9Cu1.1S) in equilibrium with Cu2-xS and CuS have been determined. The obtained experimental values have been compared with the available literature values. New experimentally determined thermodynamic properties of the solid solution (Ag,Cu)2Sss were determined.IntroductionDue to intense mining of high grade sulfide ore minerals in the past, recently, the available sulfide ores are poor in metals and becoming increasingly complex; such that, the production of high grade metals by the conventional pyrometallurgical processes is compromised. Consequently, smelters are in need to modify their operating flow sheets and strategies for processing more complex feed materials economically, while meeting the strict environmental regulations. To make the appropriate modifications, accurate thermochemical data of phases and phase assemblages which exist in these complex ore minerals are essential.Silver-bearing sulfosalts are encountered in ore minerals for the production of base metals and are common sources of silver. Among the silver-based sulfosalts, stromeyerite (Ag0_9Cu1.1S) is relatively common ore mineral in most hydrothermal vein and replacement deposits [1]. Recently, the ternary chalcogenide compound Ago0.93Cu1,07S has been studied, intensively, due to its high ionic conductivity and gradual disorder in the sequential phase transitions [2]. Therefore, accurate knowledge of the thermodynamic properties of stromeyerite has considerable fundamental and practical interest in many aspects of extractive, chemical and physical metallurgy."

Jan 1, 2014

By N. Gopalakrishnana, R. Beccard, S. Lourdudoss, R. Holz, M. Deschler

"Rapid growth of conducting and/or insulating InP, GaAs, Gao.47In0.53As, and GaAs0.6Po.4 on one or more of (001), (110), (111)A, (3ll)A and (3ll)B surfaces by Hydride Vapour Phase Epitaxy (HYPE) is demonstrated. The maximum growth rate of the binaries lies between 12 and 300 µm/hr and of the ternaries between 7 and 170 µm/hr. A simple model is developed to describe the influence of crystallographic orientation on temperature dependent growth rates. The growth rates predicted by the model is compared with the experimental values. Room temperature resistivity of insulating InP:Fe can be as high as 5xl09 ohm cm. Temperature dependent differential resistivity is also analysed. This feasibility of growing conducting and insulating layers rapidly on different orientations is very useful for electronic and optoelectronic devices.IntroductionRecently there is a renewed demand for very thick layers of III-V compound semiconductors for high performance electronic and optoelectronic devices [1]-[2]. Long wavelength high speed lasers that can be modulated up to 30 GHz necessitate epitaxial growth of semi-insulating (SI) layers [3]. There is also an increased interest on the growth of epitaxial layers on surfaces other than (001) surface. Epitaxial growth of these materials on such surfaces is of theoretical importance besides being technologically relevant. These demands led us to focus on the growth of conducting and insulating III-V compounds by Hydride Vapour Phase Epitaxy (HYPE). lnP, GaAs, Gao.471no.s3As on lnP and GaAso.6Po.4 on GaAs were grown as conducting materials using Low Pressure HYPE (LP-HYPE) on (001) 2° off substrates. Gao511no.49P on (001) GaAs substrate and lnP on lnP substrates of (001), (110), (l 11)A, (31l)A and (3 ll)B orientations were grown as semi-insulating materials using Atmospheric Pressure HYPE (AP-HYPE). In this report we present the growth aspects of these materials. We also present a simple model on the growth of InP on substrates of various orientations. The theoretically obtained temperature dependent growth rates are compared with the experimental values. Differential resistivities of semi-insulating lnP grown on substrates of various orientations as a function of temperature are also summarised."

Jan 1, 1998

By Marion Dattilo

The search for an improved anode for the electrowinning of lead from fluosi1icic acid medium has led the U.S. Bureau of Mines to investigate composites. Polymer bonded metal oxide powders which may contain catalyst additions were prepared by pressing. These composites display an improved activity toward the oxygen evolution reaction over electrodeposited lead dioxide on titanium, carbon, and nickel substrates. These composite electrodes contain 5 to 10 wt. " binding polymer, with the balance being metal oxides. Lowered anodic potentials achieved using the compnsite anodes resulted in lower levels of lead dioxide deposition during electrowinning.

Jan 1, 1995

By Corby G. Anderson

Today, with a stringent economic and environmental climate prevailing in the copper business, there is increased interest in evaluating new processing alternatives for production. Hydrometallurgical pressure oxidation of copper concentrates is one of the more viable approaches and several technological candidates have emerged. Of these, an overlooked but, ironically the first industrially proven methodology, utilized nitrogen species catalyzation in the oxidizing pressure leach system to produce copper via SX!EW. Given its many inherent process advantages, this may prove to be a feasible process alternative for the future. In this paper, the history of the system and its application to chalcopyrite concentrates will be outlined. In particular, a novel methodology for effective recovery of precious metals from chalcopyrite concentrates will be discussed. Finally, the perceived economics of this unique industrially proven process will be delineated.

Jan 1, 2000

By J. Brent Hiskey

Recently basic concepts of semiconductor electrochemistry and solid-state electronic structure theory have been applied to the dissolution of mineral electrodes. In this paper, fundamental aspects of semiconductor electro- chemistry and interfacial charge-transfer processes are reviewed. Information regarding the electronic and semiconductor properties of chalcopyrite is summarized. The electrochemical response of chalcopyrite in acidic solution is analyzed in terms of initial dissolution processes. The initial charge- transfer reaction involves the consumption of holes. It has been shorn that Fermi level pinning is consistent with observed electrochemical and dissolution behavior. Semiconductor electrochemistry has proved helpful in explaining the formation of intermediate surface films produced during the initial stages of chalcopyrite dissolution

Jan 1, 1993

By Anette Mueller, Thomas Schnellert, Sérgio C. Angulo

"The use of automatically sorting technique, to separate gypsum components from recycled material of processed construction and demolition waste (C&DW), is motivated by environmental and economical aspects. Only if the gypsum can be separated the aggregates can fulfill the environmental requirements and also the structural characteristics according to the standards. Furthermore, the separation of red brick can also improve the quality of the aggregates.This paper aims at analyzing the separation of gypsum components and red brick by using the color sorting technique. The impacts on the composition and the envelope density of recycled aggregates are described. Depending on the gypsum content the application of two processing stages (rougher-cleaner) can be necessary to produce aggregates with sufficiently low gypsum content. Additionally, the separation of red brick and concrete is successful. So, the color sorting may be a promising technique to upgrade the quality of mixed C&DW aggregates.IntroductionConstruction and demolition waste (C&DW) is a mixture of different materials. Such mixtures can be used only in low grade applications. If the material is used as certified material for road construction or as aggregate in concrete the concrete particles must be separated from the other building materials. This paper aims at analyzing the separation of gypsum components and red brick by optical sorting. The needed stages of sorting for getting a product quality according to the German Standards are deduced.Gypsum is a building material that is increasingly used for interior works in Germany like it is shown in figure 1 [1]. At present the content of gypsum in C&DW is estimated at about 1 %. Assessments on the basis of material streams of gypsum and concrete and their life spans show that higher gypsum contents of about 3 % must be expected in future [2]. Also in other countries the use of gypsum has grown considerably in the last decades. From the characterization of C&DW available in some cities in Brazil, 4 to 15 % of total amount of C&DW that may arrive at the recycling plant to be processed is excessively contaminated by gypsum. In one of these cities, the average content of gypsum in the C&DW before processing was as high as 2.1 % [3]."

Jan 1, 2008

By Guy Deschênes

Thiourea solutions can be used as leach liquors to treat gold ores or slimes. It is also efficient to elute resins or strip solvents that were loaded in cyanides solutions. The hydrogen pressure reduction is a practical step to recover gold and silver from leach solutions, and strips and eluates without any destruction of thiourea. It is a critical point because these processes have to consider the recycling of the liquors to be irore economical. The effect of temperature, pressure, acidity, compotation of the solution and the nature of catalysts on pressure reduction by hydrogen were investigated. An electranetallurgical study was? carried out to investigate the mechanism. The composition of the products was studied by different analytical methods. The process shows a good selectivity to precipitate gold and silver in a thiourea solution containing iron and copper. Gold and silver concentrations can be decreased to 0.2 ppm and 0.1 ppm at respectively 70 KPa H2 and 28°C. No decomposition of thiourea was evident during the tests. Metals such as nickel powder or platinum activate the reaction and improve the reduction.

Jan 1, 1989

By Alicia Esther Ares

This study was conducted to investigate the directional solidification of Zn-20%A1 and Zn20% A1-1O%Si-3o/oCu alloys under different conditions of heat transfer at the metal/mould interface. The type of structure obtained in both cases was analyzed and related to the solidification thermal parameters such as cooling rate, growth rate, thermal gradient and recalescence which were determined from the temperature versus time curves. These parameters were correlated with the structure-like length of columnar grains and size of equiaxed grains. The metallographic analyses were done performing quantitative metallography and composition analysis of the different alloying elements along the cast samples by SEM (Scanning Electron Microscopy) and EDXA (Energy Dispersive X-Ray Analysis). Correlations between properties, structures and thermal parameters were found.

Jan 1, 2008

By Mark Jolly

"Instead of using the traditional batch casting process, the CRIMSON [1] (Constrained Rapid Induction Melting Single Shot Up-Casting) method employs a high-powered furnace to melt just enough metal to fill a single mould in a closed crucible. The crucible is transferred to a station for computer-controlled counter gravity filling of the mould for optimum filling and solidification. The CRIMSON method therefore holds the liquid aluminium for a minimum of time drastically reducing the energy losses attributed to holding the metal at temperature. With the rapid melting times achieved, of the order of minutes, there isn’t a long time at temperature for hydrogen to be absorbed or for thick layers of oxide to form. The metal is never allowed to fall under gravity and therefore any oxide formed is not entrained within the liquid. Thus higher quality castings are produced leading to a reduction in scrap rate and reduced overall energy losses.IntroductionEngineers at the University of Birmingham, England, with local company, NTec, have invented a new casting process that will reduce the energy costs of light-metal foundries. The technology, entitled CRIMSON, means that foundries need only heat the quantity of metal required to fill a single mould rather than large batches that use unnecessary energy and create waste. The complete concept of CRIMSON requires a change of philosophy in the approach to casting and requires the user to think holistically in order to reap the full benefits from the process. This paper will discuss the various aspects of energy wastage within the foundry sector and discusses the processes whereby the energy can be reduced. Primarily the author focuses on the aluminium sector but CRIMSON can be applied to many of the non-ferrous “light” alloys. Ferrous materials and non-ferrous “heavy” alloys can also benefit from some of the ideas but not necessarily directly from the application of CRIMSON."

Jan 1, 2010

By Michael J. Nicol

The teaching of courses in geology, mining and extractive metallurgy in Australian universities is undergoing significant change largely as a result of the initiative taken by the Minerals Council of Australia (MCA). This has resulted in a major program aimed at developing national under- and postgraduate courses in selected areas with the aim of making these available to a consortium of participating universities. Murdoch University, together with the A J Parker CRC for Hydrometallurgy has been commissioned to develop the course in hydrometallurgy. Progress in the development of this course will be discussed in terms of overall philosophy, content and mode of delivery. Aspects of the extension to a Web-based course will also be summarized. Murdoch University has also established a hydrometallurgical pilot plant on the campus and the results of the first continuous operation for several months using under- and postgraduate students as operators will be discussed from the point of view of practical training and providing an interface with the local industry.

Jan 1, 2002

By Kuniaki Murase, Tetsuji Hirato, Koji Nitta, Yasuhiro Awakura

"The redox behavior of copper species in an ""ammonium imide"" room temperature molten salt was examined in order to clarify the applicability of the salt to the electroplating media of various metals. Trimethyl-n-hexylammonium bis(trifluoromethanesulfonyl)- amide (TMHA-Tf2N), having an electrochemical window of 5.6 V (50 °C), and corresponding copper(II) salt were synthesized. In TMHA-Tf2N media monovalent copper ion, Cu(I), was stable and Cu metal was oxidized, or corroded, in the presence of Cu(II) species. Cathodic electrodeposition of copper metal and anodic dissolution of it were, thus, one-electron reaction and their current efficiencies were almost 100%.IntroductionElectrodeposition of metals from aqueous solutions is an important soft process for manufacturing thin-film materials, surface finishing, and extractive metallurgy. However, the electrodeposition of base metals, such as zinc, chromium, and nickel, from aqueous media inevitably accompanies hydrogen evolution, which lowers the cathodic current efficiency of metal deposition. Since the electrodeposition of aluminium, titanium, and rare earths from aqueous media is actually impossible due to their largely negative redox potentials, nonaqueous media such as aprotic organic solvent and high-temperature molten salts have been employed for the electrodeposition of these metals. Room temperature molten salts (RTMS),1, 2) or room temperature ionic liquids, have also been developed as a promising electrolytes for the electrodeposition of base metals. In this field, chloroaluminates of alkylpyridinium or alkylimidazolium cation have been well investigated for aluminium3) or alluminium-alloy4-5) electroplating media. On the other hand, in order to avoid high hygroscopicity arising from the use of aluminium chloride, attempts have been made to combine the alkylimidazolium cations with fluorine-containing hydrophobic anions, e.g. BF4-,6) CF3SO3- (TfO-),7) (CF3SO2)2N- (Tf2N-),8) and H(HF)n-ions,9) and investigated for electrodeposition media.'°) Recently, a new series of RTMS consisting of tetraalkylammonium cations and Tf2N- anion, sometimes abbreviated as TFSI- anion, was found independently by MacFarlane et al.11, 12) and Matsumoto et al. 13) This type of RTMS, which is commonly named ""ammoniumimide"" salt, has a wide electrochemical window of ca. 5 V and, thus, the RTMS seems to be suited for practical application as a solvent for the electrodeposition process. In this paper, we report the electrochemical behavior of copper species in an ammoniumimide RTMS, trimethyl-n-hexylammonium bis(trifluoromethanesulfonyl)amide (TMHA-Tf2N)."

Jan 1, 2000

By Stephen K. Pave1

Over 1,100 tons per day of Fluid Catalytic Cracking Unit (FCCU) catalyst is used worldwide. During the cracking reaction, catalyst is contaminated by deposited metals including nickel, vanadium, potassium, copper, iron, sodium, etc. To compensate for contaminants, a portion of the circulating catalyst inventory is withdrawn for disposal and fresh catalyst is added. The DEMETR process takes spent FCCU catalyst and removes a portion of the metal contaminants, enabling the refiner to recycle demetallized catalyst, thus reducing the solid waste from the refinery. Through August, 1993, the operation of one unit for one refiner has resulted in the recycling of over 7,500 tons of spent catalyst.

Jan 1, 1994

By Zuhair A. Munir

"The use of self-propagating combustion reactions to synthesize metallic, ceramic, and composite materials is described. The limitation of this process because of the porous nature of its products is discussed. The formation of dense bodies through the simultaneous application of pressure is shown for a metal-matrix composite. The effect of an external electric field on the synthesis of ceramic and composites is described. The nature of the effect of the field on the mechanism of synthesis is analyzed theoretically and experimentally. The use of the self-propagating combustion to synthesize intermetallic thin films is presented for the Ni-Al and Ti-Al cases. The formation of functionally gradient materials (FGM) by centrifugally-assisted self-propagating high-temperature synthesis is described.IntroductionThe use of self-propagating combustion reactions for the synthesis of a large number of simple and complex materials has been described in numerous publications. These have been amply discussed in several review articles [1-4]. The many benefits of this method of materials synthesis are commonly examined in light of its most significant limitation: the porous nature of its products. The porosity in the products of self-propagating high-temperature synthesis (SHS) is an intrinsic characteristic of the process and its elimination has been the focus of numerous attempts. Various experimental methods have been used to accomplish this goal."

Jan 1, 1994

By Denis Shishin

The pyrometallurgical production and recycling of non-ferrous metals involves the use of complex feed stocks, having awide range of chemical compositions from sources that include mineral sulphide concentrates, high value obsolete materials and process wastes. The commercial viabilities of these operations hinge on the ability to extract value from these materials. Increasingly, modern computer-based tools are used to describe and predict process outcomes, including mass and heat balances, the partitioning of elements and phase equilibria. At the heart of these predictive tools are thermodynamic databases that describe the fundamental chemical properties of a system and all the components present. A comprehensive research program has been established to develop an accurate, self-consistent thermodynamic database describing all gas-slag-matte-metal-speiss-solid phases in the system Cu2O-PbO-ZnO-Al2O3- CaO-MgO-FeO-Fe2O3-SiO2-S-(As-Bi-Sb-Sn-Ag-Au). The database can be used in conjunction with the FactSage computer platform. The accuracy of the database and its application to industrial practice is demonstrated.

By Truan-Sheng Lui, Li-Hui Chen, Fei-Yi Hung, Cheng-Yi Chen

"This research used the austempering heat treatment on the SCM435 thin specimen with a type of double loop and obtained the Cr-Mo bainite structure, and then we could further investigate the mechanical properties of SCM435 bainite structure. Experimental data showed the stability of the mechanical properties of specimen with austempering temperature 830°C for 25 minutes was better than that of 15 minutes. The size of austenite grain affected the strength of thin specimen. After austempering at 830°C-25minutes and salt bath at 290°C, the stability of UTS was better than that of salt bath at 310°C and 330°C. The average hardness of all specimens was about more than HRA70. The specimen with austempering at 830°C-25minutes and salt bath at 290°C-30minutes had bigger grain size of austenite and retained y, it also had higher hardness and strength toughness. So, its stability was improved for tensile strength comparing with traditional tempered martensite process.IntroductionSCM435 is a Cr-Mo steel with high strength and high hardness properties, and it has been widely used in machine parts, shafts, gears and strength screw products [1-3]. However, this system often has lower reliability due to the brittleness of high-temperature tempering and quenching inequality. Considering the austempering heat treatment can obtain the uniform bainite structure to improve the temper brittleness, and the austempering heat treatment is a continuous process that it also has efficiency and uniformity. For the thin plate specimens, the mechanical properties of the bainite structure are better than traditional martempering structures."

Jan 1, 2013

By Mark R. Jolly, Jean-Christophe Gebelin, Aleksander Cendrowicz

"Injection of wax patterns is the first stage of the multi-stage process of investment casting. The quality of the final casting and its dimensional accuracy is highly dependent on this stage of the process. Pattern waxes used in the industry behave in a complex visco-elastic-plastic manner. The modelling of such material behaviour is therefore not simple.In this paper a number of configurations of die will be shown in which the injection of the wax has been carried out for a range of processing conditions. Some of the dies are transparent and the movements of wax front observed can be compared with those predicted by simulation. Surface defects in final components will also be shown and compared with the location predicted by simulation software. Some discussion will be presented on the limitations of the software used and the time-scales achieved for practical use as a design tool within the foundry environment. IntroductionThis paper presents the research activities carried out at the University of Birmingham on the modelling and prediction of the behaviour of industrial investment casting waxes during the injection of wax patterns. These research activities are done in the context of a more global study of the fundamental aspects of the investment casting process, the FOCAST project. Regarding the wax injection process, the aim of the project is to achieve a better understanding of the key factors that will lead to better castings. The filling of the die during the injection has been studied. Some other phenomena such as shrinkage/warpage or creep under residual stresses are also studied, but not presented here. Two commercial investment casting waxes have been characterised in order to model their behaviour and predict mould filling and subsequent defects.This paper will present the models that have been used in our work, the simulation packages used, the experiments carried out to validate the modelling and exhibit the defects due to bad filling, and finally the numerical simulation results."

Jan 1, 2001