Search Documents

By Rey B. Marquez

This paper introduces and outlines the implementation of Reliability Centered Maintenance (RCM) at Phelps Dodge Hidalgo Inc. By using a disciplined approach to the everyday maintenance functions, a proactive strategy is being developed which "raises the bar" for plant maintenance. The main objectives are: integration of Operations and Maintenance partnerships, transformation of maintenance practices from a reactive to proactive mode through the introduction of a progressive Predictive/Preventive Maintenance program (PDM/PM) paradigm changes, increased management support of maintenance functions, introduction of new indices and root cause analysis, updated; training, and definition of RCM components. RCM is the vehicle being utilized to reach the higher level of equipment availability and utilization. However, the ultimate goal is to venture beyond RCM and into the new frontier of Total Maintenance Management (TMM).

Jan 1, 1998

By Pan Cao

The process of reduction roasting of nickel laterite with rotary hearth furnace combined with magnetic separation becomes a very potential way to prepare ferronickel alloy, especially for the low grade nickel laterite ore. In order to realize this new process, the effect of roasting temperature, time and additive on the reduction degree were investigated in the laboratory experimental. The results indicated that the recovery rate of Ni increased with the roasting temperature increasing to 1500°. Most of nickel and a spot of iron are selectively reduced with adding 25.19% SiO2, 6.42% coal, and roasting for 60min at 1500℃. Then conventional magnetic separation was carried out. The content of Ni and Fe are 7.50% and 59.08% in ferro-nickel nugget prepared by this method. And the recovery rate of Ni is 90.91%, which indicates that a high recovery of ferro-nickel from nickel laterite ore is achieved indeed.

Jan 1, 2014

By Yuzuru Sato

Viscosity has been measured for various molten binary alloys of nickel with iron, cobalt and chromium in order to clarify the behavior of viscous flow of molten nickel alloys. The entire concentration range for iron and cobalt and 0-67at% of chromium content were studied. The measurement method was an oscillating cup viscometry using an alumina crucible that was precisely machined. The temperature was up to about 1880K for all the measurements. The results represented good Arrhenian relationship although some measurements included overcooled temperatures. The isothermal viscosities increased monotonously with an addition of iron and chromium into nickel. The addition of cobalt increased after stationariness. The isothermal viscosities showed concave curves. Activation energies increased monotonously by adding all the elements into nickel. These phenomena were considered to be related to the thermodynamic properties such as the heat of mixing and the structures of mixture melts.

Jan 1, 2003

By Takaaki Ishikawa

The distribution equilibria of lead, zinc and copper between CaO-Si02-Ah03 melts and liquid copper were measured at 1623K under a controlled H2-C02 atmosphere. The distribution ratios were plotted against the oxygen partial pressure, and reasonable oxide forms dissolved in the melts were estimated from the slopes of the plots. The activity coefficients of zinc oxide (ZnO), lead oxide (PbO) and cuprous oxide (CuOQs) increased with increasing slag basicity, defined by Xcao /XSiO, The temperature dependence of the activity coefficients was also measured.

Jan 1, 2003

By W. D. Cho

The slag chemistry in steel processing plays an important role in terms of the removal of impurities including alumina particles. In the present study, the dissolution of solid alumina particles in CaO-based fluxes at the temperatures between 1450 and 1550 °C has been investigated to determine dissolution kinetics and mechanism. Alumina particles were added directly in the slags and the size of alumina particles was measured as a function of time using optical and scaru;ling electron microscopes. The dissolution rate has also been obtained as a function of Si02, CaF2, MgO and MnO contents in the slags. The diffusion boundary layer between alumina and bulk slag phase has been observed and analyzed using SEM and EDX. In addition, some experiments have been performed for the dissolution of alumina in BaO-based fluxes.

Jan 1, 2003

By W. D. Cho

The slag chemistry in steel processing plays an important role in terms of the removal of impurities including alumina particles. In the present study, the dissolution of solid aluimina particles in CaO-based fluxes at the temperatures between 1450 and 1550 °C has been investigated to determine dissolution kinetics and mechanism. Alumina particles were added directly in the slags and the size of alumina particles was measured as a function of time using optical and scanning electron microscopes. The dissolution rate has also been obtained as a function of Si02, CaF2, MgO and MnO contents in the slags. The diffusion boundary layer between alumina and bulk slag phase has been observed and analyzed using SEM and EDX. In addition, some experiments have been performed for the dissolution of alumina in BaO-based fluxes.

Jan 1, 2003

By Pengcheng Li, Wei-Tong Du, Yu Wang, Gang Wen

Carbon dioxide could be utilized as a weak oxidant and a kind of coolant to oxidize elements, meanwhile, helping control the temperature during the converter vanadium extraction process. However, the optimum content of CO2 and the cooling effect of CO2 at low content have not been reported. In this study, experimental research based on the influence of different CO2 contents from 0% to 25% injected to the vanadium-containing hot metal was carried out, as well as contrast experiments of O2-N2 mixed blowing. The results indicated that the optimum content of CO2 was 15%. Under the optimum condition, the oxidation of [C] was the lowest and the oxidation rate of [V] was 96.9%, while the temperature was also lower than the O2-N2 mixed blowing. This paper provide a potential property for utilizing CO2 during the converter vanadium extraction process.

Jan 1, 2016

By Jianjun Wang, Jiaqing Peng, Lingen Luo, Zhenbang li, Yinghe Lin

Copper removal from ferronickel by FeS has been exploring studied. It is found that the decopperizing agent FeS makes the copper removal in ferronickel effectively. The effects of FeS addition amount, carbon content in ferronickel and experimental temperature were investigated. The results showed that the removal rate of copper in ferronickel increased with the amount of FeS increasing. When the dosage of FeS is 20% (mass percentage)，the removal rate of copper can reach higher than 11%. The rate of copper removal rises with the amount of carbon content increasing in ferronickel. When the amount of carbon content is 1.86%, the removal ratio of copper is 41.3%. Higher experimental temperature promotes the copper removal reaction in certain extent. The flux is acidity and weak oxidative can also promote the reaction of copper removal.

Jan 1, 2015

By R. K. Amankwah

The ability of Streptomyces viridosporus in sorbing heavy metals from wastewater has been investigated. It was found out that the biomass of the soil microorganism could be used in sorbing Pb2+, Cu2+, Zn2+ and Ni2+ ions from acidic solutions of metal ion concentration between 10 and 100 ppm. Over 99% of Pb2+ and 88% of Cu2+ ions were sorbed from wastewater of concentration 10 ppm with Ni2+ and Zn2+ recording values below 50% for a contact period of 4 hours. The quantity of metal ions sorbed per gram of biomass from the wastewater was in the order Pb2+ > Cu2+ > Ni2+ > Zn2+ and this is related to their electronegativities. Biosorption was sensitive to variations in pH and in the range investigated; metal binding was optimum at 5.5. About 63% antimony was also sorbed from dilute cyanide solution.

Jan 1, 2003

By Maribel L- Saucedo-Muñoz, Toshiyuki Hashida, Victor M. Lopez-Hirata, Shin-Ichi Komazaki

"Small-punch tests were conducted at 4, 77 and 293 K on three types of austenitic stainless steels JNl, JJl and JK2, which were solution treated, water-quenched and then aged at 923, 973, 1023 and 1073 K for 5 h. Small-punch test energy was employed for the evaluation of the aginginduced embrittlement behavior in these materials. Fracture surface of small punch test specimen for the solution treated steels exhibited a ductile fracture, showing the highest SP test energy values. The presence of intergranular brittle fracture was observed in aged specimens. Smallpunch test energy decreased significantly as the aging process progressed. The highest and lowest decrease in small-punch test energy with aging temperature occurred in JNl and JK2 steels, respectively. The decrease in small-punch test energy showed to examine appropriately the aging-induced embrittlement in these materials. The difference in aging-induced embrittlement behavior for these steels was explained based on the volume fraction of intergranular precipitates in aged samples.IntroductionA high level combination of strength and toughness is required for cryogenic structural materials used in the superconducting magnets of fusion nuclear reactor. This requirement is beyond the capability of conventional austenitic stainless steels [1]. The Japan Atomic Energy Research Institute (JAERI) developed new cryogenic JNl, JJl and JK2 austenitic stainless steels. The structure of superconducting magnets is supposed to be constructed by welding thick plates of this kind of steels. Thus, most of the components are exposed to thermal cycles. The slow cooling may cause microstructure changes in both the base material and weld zone. These changes may also decrease the fracture toughness of these materials at cryogenic temperatures. Therefore, it is important to study the effect of thermal aging on fracture toughness behavior for these steels. Konosu et al. [2] carried out a study of the effect of thermal aging on the mechanical properties for JNl steel using tension and fatigue tests. Kwon et al. [3] evaluated the deterioration in fracture toughness at cryogenic temperatures for the isothermally aged JNl steel by means of the Small-Punch (SP) test. No other reports were found about the cryogenic fracture toughness behavior for this kind of steels. To evaluate the cryogenic fracture behavior, the elastic-plastic Jrc value is a good alternative [4,5]; nevertheless, the standard required specimen size makes it difficult to be used for the fracture toughness evaluation in small zones."

Jan 1, 2011

By Toshiro Kuji, Masakazu Fujita, Tetsuji Saito

"The magnetic properties of the magnetic materials were deeply dependent on the microstructures. In this study, the novel technique to produce the desired microstructures in a controlled manner was proposed. The technique consisted of the production of the amorphous alloys and the control of the crystallization process. The technique was applied to improve the magnetic properties of Nd-Fe-B permanent magnets. The microstructural control of the magnets exhibited the excellently high energy-products of higher than 430 kJm-1. The relationship between the magnetic properties and the microstructures of the Nd-Fe-B permanent magnets was discussed.IntroductionThe intrinsic properties of the materials are basically determined by the properties of the constituent elements or the compounds. However, it is often noticed the difference between the observed properties and the theoretical values expected from the intrinsic properties of the materials. This indicates that the observed properties of the materials are determined not only by the properties of the constituent elements. In other words, the observed properties of the materials are also strongly dependent on the morphology of materials. This means that the microstructural control may creates a great improvement of the properties of materials.In Nd-Fe-B permanent magnets, the superiority arises from the uniaxial intermetallic Nd2Fe14B compound which has a large saturation magnetization and a high anisotropy field [1,2]. The magnetic properties of the Nd-Fe-B permanent magnets are dependent on the microstructure, that is, the size, shape and degree of the crystallographic alignment of the Nd2Fe14B phase. Currently, the Nd-Fe-B permanent magnets have been produced by either sintering or melt-spinning [3,4]. In the sintered magnets, alignment of the Nd2Fe14B phase is achieved by the prior green compaction of the crushed ingot powders in an applied magnetic field [3]. In the melt-spinning approach, alignment of the Nd2Fe14B phase is achieved by hot deformation [5]. Amorphous melt-spun ribbons are comminuted and then are consolidated into bulk form by hot pressing before hot deformation. As-hot-pressed magnets have randomly oriented Nd2Fe1~ grains [6]. Subsequent die upsetting of as-hot-pressed magnets gives rise to the crystallographic alignment of the Nd2Fe14B phase."

Jan 1, 1998

By John A. Mavrogenes

The Texaco gasification system developed at the Monte Bello pilot plant efficiently bums petroleum-coke thereby producing syn-gas and electricity. This system produces more electricity than conventional burners, yet the only by-products are pharmaceutical grade sulfur and V -rich slag. Vanadium is known to exist in multiple valence states in compounds which possess a wide range of melting points and physical properties. Consequently, it becomes important to carefully regulate oxygen fugacity throughout the system in order to control vanadium valence state. Vanadium phase equilibria is presently poorly understood, in large part because of the multiple oxidation states of vanadium (-I, 0, +2, +3, +4, and +5) and the difficulty of unequivocally identifying the valence state(s) in many compounds. The operation of these gasifiers at approximately 1400°C is well above the melting point of V20S but considerably below the melting temperature of V02 and V 203. If J02 can be regulated to keep the burner within the V 205 field, slag material would more likely remain molten and more easily flow out of the bottom of the burner. In pure V oxides. the oxidation state is readily determined by microprobe analysis. where V20S (V+5) is 56% V, V02 (V+4) is 61.4% V, and V203 (V+3) is 68% V. However, V valence in multi-element phases (especially phases containing other elements of variable valence) cannot be resolved by microprobe analysis alone. Petroleum-coke gasification slags collected from within the gasifier under different oxidation conditions were studied by electron microprobe analysis (EMPA). X-ray diffraction (XRD). X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy. Raman spectrometry in conjunction with microprobe analysis was found to resolve the valence of vanadium in the phases of these slags. Raman spectra collected from homogeneous single phase V-oxide standards in vacuum at low temperatures (-150°C) yielded peaks characteristic to each valence state. Gasifier slag samples are, however, much more complicated. Oxidized samples contain: fine grained (Ca. Mg, Fe. V) oxide matrix of variable composition, (Fe. V, Ni) spinel. (Fe, AI, V, Ni, Mg) spinel, V205laths, AI-Si glass blebs and Ni sulfides. Reduced samples contain: crystalline Ca-siIicate matrix, subhedral to euhedral (V, Fe, Mg, AI) spinel, subhedral V02, Fe and Fe-Ni sulfides, Fe-Ni alloys, and complex Ca-oxide matrix. The different spinel assemblages, the characteristic V-oxides and the distinctly different character of the matrices makes the oxidized and reduced slags readily discernible.

Jan 1, 1995

By Marcelo B. Mourão

An experimental investigation was carried out to -study the rates of reduction of pellets containing iron oxides by carbon dissolved in liquid iron, at temperatures ranging from 1720 K to 1973 K. Several different pellet types were employed; the materials used in the pellet's manufacture were pure hematite, two kinds of commercial iron ores, and mixtures hematite/silica and hematite/lime: Reaction times were determined employing the constant volume pressure increase technique (CVPI). It has been observed that the reaction rate increases as the temperature and the pellet's specific surface area increases. The reaction rate is also affected by the oxide type: pellets made from commercial ores or from mixtures hematite/silica or hematite/lime show reaction rates lower than those made from pure hematite.

Jan 1, 1996

By Duck Jae Lee, Kwan Ho Kim, Ji Whan Ahn

"In Korea, reutilization of constructions waste is gaining an increasing attention as generation of construction waste is projected to increase continuously. In current practices, the concrete waste is simply crushed and used as a low application such as paving, back filling, etc. In this study, a new process was developed comprising of heat pretreatment, autogenous milling, and density separation for complete reutilization of concrete waste. Firstly, the concrete waste was crushed using autogenous milling. The coarse size fractions from autogenous milling have a density of 2.5g/cm3 and a water absorption ration 3.0%, which meet the specification of the first class of KS F 2573. The fine size fractions were further separated using a hindered-settling column into two products 1) underflow, 2) overflow. The underflow sample was a high quality fine recycled aggregate which can be used for concrete making, and the overflow sample was an enriched cement material can be also used for CO2 sequestration by mineral carbonation. Introduction Kwan Ho Kim1, Ji Whan Ahn2, Duck Jae Lee1, Hee Chan Cho1 Recently, the importance of resource recycling is gaining a greater attention due to the increasing price of natural resource. Recycling is beneficial for not only the management of waste, but also the reducing of consumption of natural resources and huge energy consumption to treat of natural resource. The construction and demolition waste comprises the major industrial waste generated in Korea. It increased to 54 million tons in 2004, and is projected to increase to over 300 million tons in 2020, as many buildings reach the end of their 30 years life. Among total waste, the proportion of concrete waste was about 30% in Korea. Due to its large volume, recycling of concrete waste is the most important aspect of the waste management. In the current practices, the concrete waste is simply crushed and used as a recycled aggregate. The recycled aggregate has a low quality and most of them are down cycled for usage as paving material, back-filling material, concrete bricks, etc. It cannot be reused for replacement of natural aggregates because cement mortar is not separated perfectly from aggregates. These kinds of recycled aggregates tent to be weaker, more porous and have a higher value of water absorption. When these aggregates are used in concrete making, there are problems of higher total water demand, low compressive strength and durability [1-5]. And recycled fine aggregate is not almost recycled due to its low quality. In this study, a new processing circuit is developed to produce not only highquality recycled coarse aggregates but also fine aggregates and cement material from concrete waste."

Jan 1, 2008

By Kazusuke Sato, Takahiro Uno, Koji Hoshino

"A novel Ni coating technique of Ni(OH)2 powders was developed to improve the positive-electrode performance· of the Ni-MH batteries. It was found out that Ni(OH)2 powder was reduced by N2H4 without any catalysts in an alkaline - solution at high temperatures. In result of observation of pH and potential changes in the solution during the reaction, it was found that the reduced species was HNio2- ion dissociated from Ni(OH)2 in the alkaline solution. The molar fraction of reduced Ni of the Ni(OH)2 was increased in proportion to the amount of added N2H4. At the small Ni fraction, a porous Ni layer was formed on the surface of Ni(OH)2 powder. Open cell tests were carried out with the paste type electrodes made of either the Ni coated Ni(OH)2 powder or non-coat powder, and cell performances were compared. In result, it was found that the Ni coating technique is effective on improvement in the utilization of Ni(OH); as a positive-electrode active material under high current densities.IntroductionNi-MH rechargeable battery is generally used for the power source of portable machines and electric vehicles because of its good performance at high energy density and. long term cyclical life as well as cleanness and good safety. Cell component materials have been improved respectively, and as concerns ·the positive-electrode reducing 'the internal resistance is a principal problem to improve the discharging performance at higher current densities.In recent years, improved Ni(OH)2 powders coated with conductive materials as NI. or CoOOH have been developed for the· positive-electrode active materials in order to· reduce the internal resistance of the electrode1)· 2) The Ni coated Ni(OH)2, however, is costly because it is fabricated by .the -non-electrode plate technique which needs a expensive precious ·metal catalyst as PdC12We found that Ni(OH)2 powder was reduced by N2H4 without any cryatalysts in an alkaline solution at high temperatures. After the treatment, Ni(OH)2 powder become gray color like Ni powder from light-green color; and. turned into a magnetic. In this study, the mechanism of the -reducing reaction was investigated to apply the reactions .to a novel Ni coating technique of Ni(OH)2 powders, · and the performance of the Ni coated Ni(OH)2 powder obtained by the reducing process was evaluated as an -positive-electrode active material of Ni-MH batteries."

Jan 1, 2000

By Dajian Wang

To obtain the thermodynamic properties of a multicomponent liquid alloy system over the whole range of concentration at an arbitrary temperature, the free volume cell theory has been applied to derive the formula of activity coefficients of liquid solutions based on the infinitely dilute solutions at some temperature. The linear logarithmic relationship between activity coefficients of binary dilute solutions and reciprocal of absolute temperature have been verified, and are in good agreement with the experimental values from the literature. The Monte-Carlo algorithm was used to calculate the nonlinear end value equations of binary systems, then the free volume parameters obtained were correlated with the activity coefficients of liquid binary, ternary, and quaternary systems at an arbitrary temperature. Three dimensional a-X-T diagrams of some binary systems representing the temperature and concentration dependence of activities were plotted. The calculated results regarding non-ferrous alloy systems have been statistically examined with the experimental values from the literature. Hence, this simple approach could be useful for analyzing thermodynamic properties of liquid alloy systems.

Jan 1, 2000

By Varuzan Kevorkijan

A new method for faster production of functionally graded metal-ceramic laminates is based on reactive pressureless counterflow infiltration/penetration of a ceramic substrate with two different metallic infiltrants. The porous or dense ceramic preform is pressurelessly infiltrated or penetrated from one side by the first metallic infiltrant to the desired cross section of the preform, producing the top layer made up of the solidified infiltrant and the underlayer consisting of reactive infiltrated preform. The partly infiltrated perform is then completely infiltrated starting from the other side by the second metallic infiltrant, in this way fabricating the internal layer, consisting of the ceramic perform infiltrated with the second infiltrant and the bottom layer formed by the solidified second infiltrant. Systems already investigated include carbide, nitride and boride ceramic performs infiltrated with aluminum and magnesium alloys.

Jan 1, 2003

By Anna Wasilkowska

The study concentrates on the effects exerted by microstructure, deformation history and uniaxial stress conditions (temperature, stress state, strain rate) on the mechanical properties offerritic TRIP-aided steels for automotive applications. In low-alloyed TRIP-steels it is quite difficult to separate the effect of the austenite to martensite phase transformation from the influence of the ferritic matrix contributing to the yield stress and uniform elongation. Investigation of transformation kinetics of retained austenite as a function of the deformation temperature show that using the parameter k to characterize the retained austenite stability allows to identify regious of different temperature sensitivity separated by a transition temperature of 10±5°C. The observed low strain-rate sensitivity of the flow stress is an intrinsic property of the ferritix matrix and points to defomtation governed by slip. The ultimate tensile strength is much stronger affected by temperature than the yield stress. The influence of the temperature on the elongation is complex, because of the heating of the specimens by 60-l20°C at moderate and high strain rates. The increase of the total strain can be understood in terms of thermal softening of the ferrite. On the other hand, the steep increase of the stress during dynamic testing is an effect of accommodated elastic and plastic strains in the matrix. The strain- hardening exponent is dependent on the conditions imposed during testing. The martensite transfomtation rate is lower and the critical stress for martensite nucleation is much higher under compression compared to tensile loading. In secondary tensile tests, the yield stress increases steeply, and the ultimate tensile strength and the total elongation depend linearly on the amount of pre-straining. The results confirm that in the range of 8=10-4 s-l the TRIP-effect governs room temperature plasticity. Keywords: TRIP-steels, mechanical properties, strain rate sensitivity, temperature sensitivity, austenite stability

Jan 1, 2003

By Tobias Dubberstein, Hans-Peter Heller

The viscosity of Fe-Cr-Mn-Ni TRIP/TWIP (Transformation Induced Plasticity, Twinning Induced Plasticity) steel with varied nickel content is investigated using a vibrating finger viscometer. The viscosity of the melt is calculated from the change in power input in the field coil by an immersed finger into the liquid steel to maintain a constant peak-to-peak amplitude of the sine wave of oscillator compared to the idle state. Nickel content in steel is varied from 3 wt% to 9 wt%. The dynamic viscosity (η) at 1600 °C for 3 wt% Ni is 3.73±0.14 mPas, for 6 wt% Ni 3.50±0.03 mPas, and for 9 wt% Ni 3.93±0.09 mPas. There is a kink from low to high nickel content in viscosity values of Fe-Cr-Mn-Ni alloys. This phenomenon can be explained by a change in coordination number in the melt, as reported for Fe-Ni binary system in literature. The availability of viscosity data delivers relevant input to model free fall atomization processes of FeCrMnNi alloys.

Jan 1, 2015

By Patricia Negrini Siqueira

Abstract. Polymers are susceptible to changes in their chemical structures that affect their mechanical properties under weather condition. Exposure of plastics to UV radiation causes a loss in their mechanical properties and/or change in appearance, including reduced ductility, color changes, yellowing and cracking. Today, there are several additive systems (light stabilizers) developed to work according to resin, final application, type of cultivation, and other characteristics. This study evaluates the different additive systems (Hindered Amine Light Stabilizer - HALS, nano calcium carbonate - NPCC, nZnO and nTiO2), applied 0.75% (in weight) in linear low density polyethylene (LLDPE). The samples were mixed by high rotation homogenizer and extrusion. Later, the samples were molded by injection and aged in QUV-B simulating 6 months of exposure to weather. Tests of FT-IR and tensile strength comparing to the non-aged samples were carried out in order to evaluate the performance of several additive systems.

Jan 1, 2015