Search Documents

By Lifeng Zhang

The transport of fluid, heat ,and particles (bubbles and solid inclusions) in flowing molten steel is investigated in steel refining ladles, the continuous casting tundish, continuous casting mold and strand, and steel ingot casting processes. The two-equation k-?? model is used to simulate the turbulence. Multiphase fluid flow is numerically simulated with a Lagrangian-Eulerian approach, an Eularian-Eulerian approach and the Volume Of Fluid (VOF) method. The simulation can predict inclusion trajectories, inclusion removal fraction, free surface waves and other phenomena, which can be used to optimize these important metallurgical operations.

Jan 1, 2006

By Jinhui Li

Silver is a very important metal used in a wide range of applications. It is necessary to recovery of Ag from electronic wastes for increasing of Ag price and circumstance protection. For separating and recycling Ag from Ag-Cu composite materials, thermodynamic data of reaction is calculated and some experiments have been proceeded with Ag-Cu composite material scraps, time, temperature, nitric-sulfuric mixed acid volume ratio and the volume ration of mixed acid vs. water have been discussed. The results show that the optimization conditions is that nitric-sulfuric mixed acid volume ratio 5:95, volume ratio of mixed acid vs. water 10:1, temperature 55?, time 25min. In the conditions, Ag can be selectively leached from Cu-based composite material, Cu base is not eroded nearly.

Jan 1, 2009

By Sergio N. Monteiro

Jute fiber reinforced polymer composites are among the most investigated and applied natural composites. In this past decade the mechanical properties of these composites has been assessed for various types of test conditions. However, the reported results correspond mainly to short-cut jute fiber composites, which do not present the highest mechanical strength as compared to continuous fibers of the same kind. In order to complement these results, the present work evaluated the mechanical behavior, by means of flexural tests, of polyester matrix composites reinforced with continuous jute fibers. Bend tests were conducted in standard specimens with up to 40% of jute. Fracture analysis by SEM displayed the rupture mechanisms. The results showed an improvement in some flexural properties with incorporation of jute fiber. However, a low fiber/matrix interfacial stress was responsible for limitation in the values attained by some properties.

Jan 1, 2010

By Jerry D. St. Clair

A multidisciplinary team of scientists and engineers at Wont has been working to understand heavy metal contamination of DuPont process waste streams and technologies for abatement of these metals. As part of this effort, an extensive study was made of a specific waste stream of importance in DuPont's environmental commitment. This 200 gpm stream contains 5-5000 ppm of nickel plus a variety of inorganic and organic constituents. The chemical complexity of the waste rendered conventional. alkaline precipitation ineffective, and only through the simultaneous application of analytical characterization, fundamental chemical understanding, and process engineering did effective technical approaches emerge. In this instance, ion exchange, sulfide precipitation, and caustic digestion ultimately proved successful in reducing the nickel to below the 1 ppm target. The results of this study will be presented, along with key learnings about the process of solving heavy metal contamination problems.

Jan 1, 1994

By F. Sanchez, A. Mejias, C. Frias, G. Diaz

"Crude zinc oxides are the major source of secondary zinc and are produced from fuming processes like Waelz kilns. The impurities of crude zinc oxides make difficult their processing in primary zinc refineries due to mainly high chloride tenor. Washing with sodium carbonate is a costly operation and chloride removal efficiency is not good enough, so further purification steps are required. The crude zinc oxides are easily treated using ZINCEX™ technology based on leaching, solvent extraction, and electrowinning. The ZINCEX™ process is commercially available and is designed to be a perfect barrier for metallic impurities and halogens, allowing selective zinc extraction in mixed chloride and sulfate leaching solutions. Other valuable components as lead and silver can be efficiently recovered from the leaching residue using PLINT technology in chloride media. Silver is recovered as silver cement and lead is precipitated as pure lead oxide or carbonate, which can be smelted at low temperature.IntroductionZinc is a fully recyclable metal and at present approximately 70% of the zinc produced worldwide comes from primary zinc while 30% originates from secondary materials. Nowadays, the zinc recycling rate is continuously increasing mainly through galvanized steel scrap processing, and crude zinc oxides are the major source of secondary zinc [1]. Secondary zinc oxides are obtained from fuming processes like W aelz Kiln, Rotary Hearth Furnace or Primus Furnace. Waelz is the dominant technology accounting for 80% of total crude zinc oxides production worldwide. In the Waelz process, steel dust is mixed with solid fuel reductant (coke breeze) and pelletized. It is then fed to the kiln and heated to a reaction temperature of l ,200°C. In such conditions, zinc, lead, and other non-ferrous metals are vaporized into the flue gas together with chlorides and alkaline metals. Mixed oxides are drawn from the kiln with the process gases and separated to produce typical crude zinc oxides [2]."

Jan 1, 2011

By Sutham Niyomwas

Silicon-Silicon Carbide (Si-SiC) composites were synthesized by self-propagating high temperature synthesis (SHS) from a powder mixture of SiO2-C-Mg. The reaction was carried out in a SHS reactor under static argon gas at a pressure of 0.5 MPa. The standard Gibbs energy minimization method was used to calculate the equilibrium composition of the reacting species. The effects of silica sources and carbon mole ratio in precursor mixture on the Si-SiC conversion were investigated using X-ray diffraction and scanning electron microscope technique. The as-synthesized products of Si-SiC-MgO powders were leached with 0.1M HCl acid solution to obtain the Si-SiC composite powders.

Jan 1, 2009

By WU Jian-hui

Keywords: metallic material; nickel powder; thermal decomposition; precursor; fibrillar powder; nanometer scale; passivation treatment The precursor thermal decomposition process of fibrillar nanometer scale nickel powder and passivation treatment of obtained powder are investigated, and the composition and morphology of the products are characterized by use of IR, TGA/DTA, XRD and SEM. The results show that the precursor morphology is a decisive factor to the product morphology of the nickel powder. The morphology of the product derived at low decomposing temperature is irregular. The nickel powders produced at the temperature higher than 480 coheres seriously. The product particles are reunited with the decomposition time prolong. The powder prepared under the optimal condition is fibrillar like woolen yarn; the grain diameter is less than 50nm.

Jan 1, 2005

By Gary A. Wickham

In the zinc industry, this past decade has seen both prosperity and depression. Significant changes have occurred throughout the world in mining, smelting, refining, and marketing. This paper will review many of the industrywide changes of recent years and the potential impact for 1990s. In addition to an historical review of supply and demand are discussion of technology considerations for zinc and zinc based products, effects of geographical shifting of markets, and projections for the 1990s.

Jan 1, 1990

By Olga Frank-Kamenetskaya

The experimental results of study of atmospheric corrosion processes on Saint-Petersburg bronze monuments surface, received in situ and by means of simulating experiments, have been discussed. Influence of the time factor on corrosion film (patina) mineral composition has been analyzed. Direct dependence between patina mineral composition and environmental conditions has been proved. The sequence of patina phases crystallization has been established. Effect of the chemical composition and heterogeneity of artistic bronze and also monument surface structure on the rate of corrosion process has been regarded. The time variations of mass of the crystallized in the hydrochloric acid vapor phases have been investigated. The kinetic laws of their development at the initial stage of formation, indicating simple (non chain) reactions, have been revealed.

Jan 1, 2006

By Richard S. Kunter

Artech Recovery Systems, Inc has developed a low pressure and temperature? leach process called the "Cashman Process" to extract metals from arsenical flue dusts and residues and fix the arsenic in an environmentally stable form as ferric arsenate (scorodite). The process was pilot tested at Hazen Research in an integrated plant including continuous recycle from August 1989 to October 1989 during which several tons of flue dust were processed. Based on this pilot program, the process was deemed technically feasible and produced commercially salable products. Residues from this pilot program were subjected to a long-term stability test jointly designed by PTI environmental services and the USEPA. The process, its versatility, and the nature of the products is discussed in some detail.

Jan 1, 1992

By Elisa Alonso

Recycling is generally a more sustainable alternative to landfilling. Its financial costs however, do not always justify its practice, especially in the short term. As a result, even for precious metals such as platinum, significant amounts can end up unrecovered. In considering risks of materials scarcity for firms that require platinum and platinum products, this paper examines how recycling provides additional benefits as a risk-mitigating strategy against scarcity. The experimental platform for this examination is a System Dynamics simulation model that strives to capture the dynamics of platinum market supply, demand and price. The detailed structures of supply and demand are key features of the model. Results show that since the secondary supply of platinum depends on a supply chain separate from primary extraction, recycling can diversify the risks of primary supply instabilities and reduce the impact of price fluctuations upon firms.

Jan 1, 2009

By Ing. R. Geutskens

Zinc-bearing dust from blast furnace gas-scrubbing operation is a well known environmental health problem in the iron and steel industry. Hoogovens IJmuiden (The Netherlands) developed processes to solve this problem. 90% of the zinc is concentrated in 25% of the dust (the fine particle fraction) by means of slurry-hydrocyclonage. The resulting fine particle fraction is treated in a pressure leaching process. Hydrochloric waste pickle liquors have been used as a leaching liquor. By creating optimal leaching conditions more than 98% of the zinc is brought into an acid' solution, whereas nearly all the iron remains in the residue. The zinc can be separated selectively from the solution. The residue can be reused in the blast furnace (via the sintering plant). In the article information is given about the research work and -results of the pressure leaching process as well as the possibilities of the process for solving comparible problems.

Jan 1, 1990

By F. F. Aplan, G. Simkovich

"A review is given of the effects of solid state point imperfections upon a number of mineral benefication processes and a metal extraction process. It has been found in numerous flotation studies that small amounts of aliovalent impurities (dopants) in binary compounds may show major effects upon flotation behavior. Both semiconducting and ionic conducting compounds are affected. These effects are also seen in hydrometallurgical studies as well as in electrostatic operations. Additionally, de-copperization of lead melts appears to be strongly influenced by similar defects. It is hypothesized that the effects observed in these studies are present in actual operations and should be considered in designing processes. A few speculations concerning future efforts are advanced. IntroductionImperfections [point (e.g., vacancies, interstials, quasi-free electrons, electron holes, impurity ions), line (e.g., dislocations), two dimensional (e.g., grain boundaries) and three dimensional (e.g., 2nd phases) defects] are generally present in solid materials and these imperfections may, and often do, have important effects upon a variety of properties and processes. In general, one may, in most cases, attain elimination of three dimensional defects by a separation process of one type or another (e.g., gravity, electrostatic, magnetic, flotation, hydrometallurgical etc.,). Thus, this type of defect has rarely been investigated in a systematic fashion. Two dimensional defects are always present in non-single crystal materials but have also escaped systematic studies in processes primarily because the control of such defects is not easily attained. Line defects are non-equilibrium entities which are present in ill-defined quantities so that they present a variable that cannot be easily controlled although through careful systematic experiments one can attain some reproducible relations pertaining to this type of defect.Contrary to the lack of studies concerned with the effects of 1, 2 and 3 dimensional types of defects there has been some activity concerned with point defects and their effects upon a number of mineral/metallurgical processes, especially flotation processes. Thus, this article will present a review primarily of point defects in relation to their effects upon flotation although other processes and defects will also be mentioned."

Jan 1, 1988

By T. T. Chen

Copper anodes generated from copper scrap are relatively rich in Sn, Zn and Fe. Because of the presence of oxygen, only trace amounts of Sn occur in solid solution in the copper crystals. Thus, Sn occurs mainly as SnO2, Cu-Sn-Ni oxide and Sn-Ni-Zn oxide in the copper anodes, and Zn and Fe occur mainly as minor constituents in the Sn-Ni-Zn oxide and Cu-Sn-Ni oxide. During electrorefining, these oxide species are liberated from the copper anodes and report directly to the anode slimes. The trace amounts of Sn present in solid solution in the copper crystals dissolve but reprecipitate as Sn arsenate or a Sb-As-Sn-O phase. Accordingly, high Sn contents in copper anodes do not lead to elevated Sn concentrations in the electrolyte.

Jan 1, 2010

By Ian F. Hughes

"Concepts of an integrated steel plant for sheet products to be built and operating in the year 2000 will be described. The design and operating methodology of this market driven facility will integrate process uniqueness, standardization, manufacturing automation, artificial intelligence and information flow.An integrated steel plant for the year 2000 is defined for this article as one that will be built on a greenfield site and ""started up"" in the year 2000 with a capacity of three million tons per year of flat rolled products ranging from cold rolled and electrical steels to high strength formable steels and a full range of coated products.It may seem that the 21st century and the steel plant we're discussing are far into the future. The startling truth, however, is quite the opposite. As shown in Figure 1, even with accelerated development, a new process on which laboratory development work is begun today might just barely pass through the laboratory phase, pilot plant, and commercial feasibility stages such that it can be considered viable for construction and start up in the year 2000.On that basis, it is very unlikely that this 21st century steel plant will utilize any technology that isn't at least under investigation in the laboratory in 1988. As a result, we recognize that planning and selecting the facilities for this plant is, in fact, a pragmatic rather than futuristic process, and that its main value is in providing a bridge to longer-term predictions."

Jan 1, 1988

By Alan P. Prosser

The heap leaching of gold ores by cyanide solution was simulated by computer program. The program uses only basic m1neralogical and chemical data; no process testwork data, such as column leach results, are required. The simulation can be used to forecast the consequences of various changes before and during the testwork, design and operation stages of a particular ore-process system. Also, data about the state of different parts of the heap at various times help create an understanding of what is happening. The effects of mineralogical and process variables on the overall performance of the ?heap leaching process are illustrated. Comparisons are made to column leach tests and production data. The potential of the simulation strategy is discussed for making better use of operating experience and for suggesting specific research objectives. It has become clear that more attention should be paid to other metals that dissolve in the solution.

Jan 1, 1989

By Gábor Csicsovszki

We have developed a novel method - at the laboratory scale - comprising an ion-exchange separation and a membrane-electrolysis step for the purpose of zero-waste regeneration of spent HCl pickling liquors originating from hot-dip galvanizing of common steels. It is aimed at the parallel regeneration of HCl and iron. Experiments revealed that iron can be electrodeposited at high current efficiencies by maintaining the following conditions: 0.04-0.08 M HCl, 500-1000 A/m2, 20°C and stationary electrolyte in a conventional cell. Zinc in the solution did not disturb the deposition of iron, however it contaminated the product and it poisons the anion-exchange membrane required to tackle acidity during electrolysis. For a preliminary separation, anion-exchange tests were carried out to produce pure iron solutions. Beyond the equilibrium studies, column experiments were carried out showing that low flow rates of the loading solution and the ~1.5 M HCl eluent are essential for separation.

Jan 1, 2006

By J. Szekely, S. Rhee

"A mathematical formulation has been presented to describe heat and fluid flow phenomena in CVD operations. In the statement of the problem, which included consideration of plasma enhanced CVD systems, emphasis was placed on identifying the parameters which play a key role in determining the rate and the spatial uniformity of the deposition process. This was done both through the appropriate dimensionless groups and by presenting an extensive set of computed results. The main conclusions that may be drawn from this work are that the deposition rate will be inherently non-uniform for atmospheric CVD systems; this may be somewhat ameliorated by inclining the susceptor or changing the vessel contours. Operation at greatly redeced pressures and for PECVD systems will give a much more spatially uniform deposition rate.1. INTRODUCTIONIn recent years, there has been a growing interest in chemical vapor deposition techniques for the preparation of thin films for semiconductor, photovoltaic applications and for coatings in general, as evidenced by numerous journal articles and symposium proceedings devoted to this topic (1-6). An interesting variant of this technique is to perform the deposition in a plasma or glow discharge at low pressures because this technology obviates the need for the thermal decomposition of the precursor at the substrate surface and permits operation at greatly reduced temperatures (7-10).By far, the largest portion of the reported work dealing with both these aspects of the technology has been concerned with the characterization of the deposit, quite properly so. However, in more recent times it has been realized that the transport aspects of these processes are also deserving of attention because the understanding of heat flow, fluid flow and diffusional phenomena may provide the key to the solution of problems associated with obtaining uniform deposits and the proper scaling of laboratory measurements in order to design industrial CVD systems."

Jan 1, 1986

By Jerome Feinman, Sven O. Santen

"The principles involved in the generation and application of plasma energy are reviewed briefly and the major developments in commercial and semi-commercial primary metal and alloy production are described and discussed in broad outline, with emphasis on present performance and future potential. New concepts in the application of plasma energy in primary operations are described with emphasis on the expected advantages over conventional technology and the problems that have to be solved to enable effective implementation.IntroductionThe use of plasma energy in industrial processes is generally considered to have started in 1905 with the operation of the Birkeland process for nitrogen fixation for fertilizer production. Although it seems logical to apply plasma energy to metallurgical processes, which also usually require considerable energy at high temperature levels, serious development work along these lines did not begin until the early 1970's. The reasons for this hiatus are associated in part with recognized difficulties in applying plasma energy in processes involving tonnage quantities of solids in severe industrial environments and the delicate nature of the earlier plasma generators. Another, and perhaps overriding factor, is the fairly steady improvement in efficiency and economy of most primary metal producing processes by conventional developments and modifications through the 1950's and 60's. Examples of these evolutionary changes include burden preparation and fuel injection in blast furnace applications and prereduction treatments in ferroalloy operations. By the end of the 1970's most primary metal producing processes had been optimized close to the limit, at least in terms of those operations that were able and willing to implement the developed improvements. In this context, plasma energy offered the possibility to achieve further significant improvements in primary operations where conventional means were exhausted."

Jan 1, 1988

By Liang Sha

In this study, adsorption of copper by chemically modified orange peel was investigated. A conspicuous change occurs in the surface morphology of the biomass due to modification, which is depicted by SEM images. Equilibrium isotherms and kinetics were obtained and the effects of various factors, including solution pH, contact time, initial metal ions concentration and temperature, were studied by batch experiments. Kinetics was found to be best-fit pseudosecond- order equations. Equilibrium was better described by Langermuir isotherms rather than Freudlich isotherms. At 25?, pH5.30, the maximum adsorption capacity was 70.67mg?g-1 . With increase of temperature, adsorption efficiency decreased. The biosorbent was suitable for repeated use for more than five cycles.

Jan 1, 2009