Search Documents

By Phillip E. Gramlich

Through extensive practical experience and multiple studies, tensioned roof control systems have proven beneficial in difficult mining conditions. Due to increased mining of less desirable seams, tensioned roof control systems have claimed a progressively larger share of the total number of roof bolts installed in the US coal industry. Each tensioned roof control system has its benefits, but also has problems concerning cost, cycle time, stress concentration, load retention, and protrusion into the mine opening. For example, resin-assisted mechanically anchored bolts (also known as resin point anchor bolts) have a fast cycle time and the potential for high tension loading, but the stress from the mechanical shell is concentrated in a small area and can create concerns with certain roof structures (Zhang and Peng, 2001). Resin point anchor bolts can be difficult to fully grout. The cost of resin point anchor bolts can be an issue; a two-piece resin point anchor bolt has a large number of parts (10) and manufacturing steps (9), adding to its higher cost. Tension rebar bolts can achieve high loads and are easier to fully grout but have longer cycle times. In addition, a high percentage of the installed load can ?bleed off? if the resin mixing time or the ?hold time? before tensioning is short-circuited. Tension rebar bolts can be notorious for protruding into the mine opening, creating an obstruction for man and machine (Figure 1), in particular, with reduced mining heights. A new tensioned roof control system has been developed that doesn?t have moving parts, is cost effective, provides fast cycle times, has a low profile, and is simple t install.

Jan 1, 2014

By Brian Daniels, James Farroni

"Draw rock (small rock that forms/falls when bolting the roof and/or rib) is the cause of numerous injuries annually. These injuries result in lost work hours and low morale. The report below explains how ""Mine Safe Draw Rock Shields"" (Pans) are used in an underground operation. This report will chronicle the application of these pans in a Southern West Virginia coal mine along with testing data that measures their effectiveness. Since the introduction of these pans in 2002 the amount of reportable accidents relating to draw rock has decreased by 80%. The report below reinforces that perimeter contact is critical to the performance of these pans. In addition the strength of these products at the perimeter will determine their effectiveness. The results of the testing data outlined in this paper, along with the physical records at the study mine, confirm that the use of pans has significantly reduced draw rock falls at this facility.BACKGROUNDSupplemental support is defined as ground control that is used in addition to required support in an underground mine. Some examples of supplemental support are:• Pans• Mesh/Geogrid• Mats• Half Headers• Boards• ChannelA typical roof condition that warrants the use of pans is when loose small rock is dislodged while bolting. If the top is very scaly (loose, thin rock) additional supplemental support can be used in conjunction with pans such as mesh or geogrid (See Figure 1). Pans will provide protection where used and approximately 12 in (250 mm) out from perimeter. This is achieved by contact with a surface which will put scale in tension up to 12 in (250 mm) from perimeter of pan.INTRODUCTIONThe ease of applying a roof support system is critical to effectively operating a deep mine. Figure 2 shows how a pan is installed in conjunction with a roof bolt and bearing plate. The Mine Safety and Health Administration (MSHA) requires that supplemental support cannot decrease the performance of required support. The goal of using all supplemental support is to provide additional safety for the miner which equates to increased productivity.The ability of skin control products to contact a surface is the single most critical characteristic (Figure 3 and Figure 4). If the material does not contact the surface it cannot be effective. Therefore, the flexibility, design and proper installation of the products are critical in determining their effectiveness. Figure 5 shows the proper installation of the roof pan.To reiterate, all skin control must be applied in conjunction with a roof bolt and ASTM approved bearing plate as shown in Figure 4."

Jan 1, 2010

By Robert J. Coutts, Dan A. Payne

"The Broadmeadow mine is a punch longwall mine owned and operated by BHP Billiton Mitsubishi Alliance (BMA) in the Bowen Basin of Queensland, Australia. In 1999, an exploratory adit was driven as part of the feasibility study for the establishment of the mine. Subsequent development of the mine in 2004 started some distance away from the initial test adit. Ten years later, the trial adit would be used as the headgate of the 5'h longwall panel. However, multiple roof falls had occurred in a heavily jointed area over a distance of 1, 000 ft (300 m) during the past 10 years. Due to the immediate coal roof, low stress environment and time, some of these falls had progressed to 38 ft (11.5 m) above the mining floor. As a result of the extensive work involved and safety implications of trying to recover the roof falls conventionally, a strategy was developed to fill these roof falls with a cement based product from the surface, down boreholes, and redrive the roadways through the consolidated roof fall material. This paper describes the process of rehabilitating these roadways, the results when the roadway was redriven and the headgate performance as the longwall mined through the area.INTRODUCTIONBMA operates 7 open cut and 2 underground mines in the Bowen Basin of Queensland, Australia producing over 50 mt per year of high quality coking coal. As a result, BMA has established over 150 miles (250 km) of open cut highwall.Broadmeadow Mine is a punch longwall mine located 22 miles (35 km) north of Moranbah in Queensland, Australia on the western limb of the Bowen Basin Coal Measures (Figure 1). Broadmeadow Mine commenced development in 2004 and began longwall operations in 2005. Broadmeadow is currently completing the fifth longwall panel and produces over 4 Mt per year of high quality coking coal. Mining is undertaken in the Goonyella Middle Seam, which is 21 to 25 ft (6.5 to 7.5 m) thick in the current mining area.The mine layout required the use of an old exploratory gateroad as the headgate of its 5th longwall. This gateroad had experienced numerous large roof falls and required extensive rehabilitation."

Jan 1, 2010

By Daniel W. H. Su

"This paper presents results from a recent study conducted to evaluate the effects of longwall-induced stresses and deformations on the mechanical integrity of shale gas wells drilled over a longwall abutment pillar. The primary objective is to demonstrate that a properly constructed gas well in a standard longwall mining abutment pillar can maintain mechanical integrity during and after mining operations. Successful designs would allow for the safe recovery of both coal and gas reserves. Major elements of this comprehensive study include: (1) modeling of rock movements to predict impacts on gas wells, (2) measurements of actual rock movements at the surface and in the subsurface, (3) measurements of actual impacts on test wells designed similarly to real shale gas wells, ( 4) comparison of modeling results to actual rock movements to validate the model, and (5) employing the validated models to evaluate various casing and cementing designs to minimize casing deformations and absorb longwall-induced strains along the intermediate and production casings.A study site was selected over a southwestern Pennsylvania coal mine, which extracts 1,500-ft-wide longwall faces under about 600 feet of cover. Four test wells and four monitoring wells were drilled and installed over an abutment pillar with 125-ft by 275-ft centers. The four test wells were drilled to a depth of 642 ft, or 42 ft below the Pittsburgh seam, and were designed like a real shale gas well, except that only three casings (namely the surface, water protection and coal protection casings) were installed in each well. Casing steel grades, wellbore diameters and annular spaces were purposely varied in each of the four test wells to evaluate the effect of different well designs. The four monitoring wells - one vertical extensometer and three in-place inclinometers (IPI) - were drilled to different depths to measure the vertical settlement and horizontal displacements as a result of longwall mining on both sides of the abutment pillar. In addition to the test wells and monitoring wells, surface subsidence measurements and underground coal pillar pressure measurements were conducted as the 1,500-ft-wide longwall panels on the south and north sides of the abutment pillar mined by."

Jan 1, 2016

By Nikzad Oraee, Parham Khajehpour, Kazam Oraee, Arash Goodarzi

"Rock fall related accidents continue to occur in coal mines, although artificial support mechanisms have been used extensively [1]. Roof stability is primarily determined in many underground mines by a limited number of methods that often resort to subjective criteria. It is argued in this paper that stability conditions of mine roof strata, as a key factor in coal mines, must be determined by a survey which proactively investigates fundamental aspects.Failure of rock around the opening happens as a result of both high rock stress conditions and the presence of structural discontinuities. The properties of such discontinuities affect the engineering behavior of rock masses causing wedges or blocks to fall from the roof or slide out of the walls [2]. A practical rule based approach to assess the risk of a roof fall is proposed in the paper. The method is based on the analysis of structural data and the geometry and stability of wedges in underground coal mines. In this regard, an accident causing a huge collapse in a coal mine leading to four fatalities is illustrated by way of a case study. A comprehensive investigation of the hanging wall has been gathered through a systematic collection of evidence. The investigation results are then analyzed, and an interpretation of the evidence gathered is provided.For this purpose, horizontal and vertical profiles are prepared by geophysical methods to define the falling zone and its boundaries. The collapse is then modeled by the use of sophisticated computer programs in order to identify the causes of the accident and hence recommend corrective actions to prevent or minimize reoccurrence probability of similar accidents. The corrective measures are placed into a rule-based framework for the benefit of the mine operators.INTRODUCTIONRoof rock failure has generally been the most dangerous hazard for underground coal mining in the world. Failure of rock around shallow coal mine openings often results from loosening of blocks of rock on the weakened planes under the influence of gravity. This condition is not typically seen in large deep coal mines. There are a number of differences between large mechanized mines and small mines related to ground control [3]."

Jan 1, 2015

By Ismet Canbulat, John Naylor, Jason Emery, Peter Craig, Andy Sykes

"Longwall mining is by far the most common method of underground coal extraction in Australia. The industry trends and expectations are placing increasing emphasis on the reliability and productivity of these operations. The longwalls are becoming wider and longer while retreat rates are continuously increasing due to significant improvements achieved in longwall equipment reliability and automation. This increased longwall productivity is placing significant emphasis on the reliability of longwall panel development.Although there have been significant improvements in the reliability of continuous miners and hydraulic drill rigs, the traditional resin encapsulated bolt installation is still the principal method used in all major coal-producing countries around the world. Anglo American realised an opportunity existed to introduce an alternative roof bolt installation technique called “spin to stall” in Australia. Spin to stall was first introduced in Anglo American Coal in South Africa where it has been successfully used for over a decade, though implementation of South African spin to stall resin in Australia has proven to be near impossible due to a significant difference in geotechnical conditions, mining method, and, subsequently, roof bolting equipment. Therefore, a new spin to stall development project was initiated between Anglo American Coal and Jennmar Australia (SPIN2STALL®). This paper summarises the journey of this project, the results, and the successful implementation of spin to stall achieved at Grasstree Mine.INTRODUCTIONThe Anglo American Coal business unit operates Grasstree and Moranbah North underground longwall mines in the Bowen Basin of Central Queensland, with a third longwall mine, Grosvenor, currently being developed, and two more (Aquila and Moranbah South) in the project pipeline. The vision for Anglo American is to achieve “Zero Harm” through the effective management of safety at all operations, while for the coal business unit, at the same time to achieve industry-leading operational performance. Currently, both Grasstree and Moranbah North longwalls are operating at industry best practice rates. This is placing increased pressure on the development process to allow such high productivity levels to be sustainable."

Jan 1, 2015

By Weijia Guo

With the exploitation of coal resources, a large area of land had been affected by surface subsidence, causing conflicts between man and land to become more conspicuous by the day, affecting the life of general public, and constraining further development of the land. This paper predicts the subsidence areas according to the 10-year mining plan of the Jibei mining district as an example. A plan of environmental management was developed based on sciences and practical economics.

Jan 1, 2006

By Meng Xiao, Peng Huang, Lizin Lan, Feng Ju, Shuai Guo

"Through changing the axial load on backfilling material compaction test to reflect different overlying strata pressure on backfilling material, the stress-strain relations in the compaction process of backfilling material under the geological condition can be obtained. Based on the characteristic of overlying strata movement in backfill mining, a model of roof thin plate is established. By introducing the stress-strain relation in compaction process into the model and using RIZT method to analyze the bending deformation of roof, the bending deflection and stress distribution can be obtained. The results show that the maximum roof subsidence and maximum tensile stress occurring at the center are 255mm and 5 MPa, respectively. Tensile fracture of roof under the geological condition of Dongping mine did not occur. The dynamic measurement results of roof in Dongping mine verify the theoretical result from the aforementioned model, thereby suggesting the roof mechanical model is reliable. The roof thin plate model based on the compaction characteristic of backfilling material in this study is of importance to research on backfill mining theories and application of backfilling material characteristics.INTRODUCTIONSolid backfilling mining (SBM) is a green mining technology in which the solid waste materials is placed into the gob to support the overlying strata and to control roof's subsidence and movement (Miao, 2012; Miao et al., 2010, 2015). SBM has been successfully used in several mines to solve many problems, including coal extraction under buildings, water bodies and railways, surface subsidence, and environmental problems. Good results have been obtained in many mines (Zhang et al., 2009). The key in the application of SBM technology is controlling strata movement. However, the critical factor influencing the controlling effect of strata movement is compaction characteristics of backfilling materials. Thus, a roof model of SBM is built based on the filling materials' compaction characteristics. A subsidence equation and the critical failure condition of roof was given and field verification was performed at Panel 15061 of Donping Mine."

Jan 1, 2016

By Andre Zingano, Anderson Weiss

"The objective of this paper is to study the behavior of a low thick and low depth coal seam and the overburden rock mass. The mining method is room and pillar in retreat and partial pillar recovery. The excavation method is conventional drill and blast because of the small production. The partial pillar recovery is about 30% of the previous pillar size, 7m x 7m. The roof displacement was monitored during retreat operation; the surface movement was also monitored. The effect of the blasting vibration on the final pillar strength had been considered. Due to blasting, the pillar reduced about 20%. The consequence is more pillar deformation and roof vertical displacement. The pillar retreat and ground movement were simulated in a three-dimensional numerical model. This model was created to predict the surface subsidence and compare to the subsidence measured. This study showed that the remaining pillar and low seam reduce the subsidence that was predicted with conventional methods.INTRODUCTIONMining low coal seams (less than 1 meter) with the room-and-pillar mining method implies the excavation of part of the roof or floor to maintain adequate entry height for equipment and compliance with labor regulations with respect to ergonomic issues. The direct consequence of this is an increase in coal contamination and the increased cost of transportation and preparation at the plant. Traditional room-and-pillar mining only uses a development operation, even with a continuous miner or drill-and-blasting. Therefore, all the run of mine (ROM) coal is carried out with part of the roof or floor. However, if the retreat mining method were to be considered, the quality of the coal could increase because only the coal seam is excavated from the pillar recovery. The quality of ROM coal will increase, and the cost will decrease proportionally to the amount of coal produced from the retreat operation.However, the retreat mining with partial or total pillar recovery implies greater subsidence. This is particularly true if the coal seam depth is shallow, under 100m depth. Subsidence prediction in room-and-pillar retreat mining is complex; it depends upon the remaining pillar (stump pillar) size, as well as the pillar height, and the behavior of the pillar after retreat. This is related to the strength of the remaining pillar, which is related to the excavated method (drill-and-blast or mechanical)."

Jan 1, 2018

By Kousick Biswas

The main objective of occupational health and safety research is to minimize or eliminate the events that may cause fatal or non¬fatal injuries to human workers. A commonly used technique is to devise an "incident prevention plan", which is more often the product of thorough investigations of past reported incident events. Incident documentation and methodical reporting and systematic and thorough data collection, often help identify the root cause of the incident - in other words, the etiology of the incident. These retrospective analyses of the incidents can efficiently identify the future steps to take to achieve the objective of minimizing occurrence of "events of interest". This paper introduces a novel technique - "Taxonomic Analysis", which identifies the root causes of an event (an incident in this case) and can provide future direction for corrective measures to reduce the probability of occurrence of the event. A taxonomic analysis involves systematic and organization of data based on observation, description, and classification. This paper utilizes the rock fall related incident narratives, available with the Mine Safety and Health Administration (MSHA) database (1984¬1999), for a taxonomic analysis. The study found that 67.6% of groundfall incidents occurred in supported areas with the remainder (32.4%) in unsupported areas. Some form of rock mass failure appears to cause about 50% of groundfall incidents, although in 39.7% of the overall groundfall incidents or two-thirds of those involving rock mass failure, the exact nature of the rock mass failure could not be determined from the narratives. Human activities factors such as scaling or barring down, drilling or bolting, and setting timbers or cribbing accounted for another 34.5% of the groundfall incidents. Finally, support system failures made up the remaining 15.5%. Results from this taxonomic analysis may suggest focus areas toward which preventive measures and future research activities could concentrate.

Jan 1, 2003

By Chris Kelly

The Monroe County Quarry is an open pit granite quarry located near the town of Bolingbroke. Monroe County. Georgia. The quarry has been in continuous operation for approximately 10 years. The quarry covers approximately 27 acres and has an annual production rate of 1.0 million tons. On the morning of April 26. 2000 a sudden rapid highwall failure occurred at the west end of the north wall of the quarry pit. The failure occurred approximately one hour after a three inch-wide crack was observed in an access road located at the crest of the highwall. No indications of failure had been observed prior to the development of the crack. The active mining area had been at the base of the failed area. The pit was successfully evacuated prior to the failure and there were no losses of either personnel or equipment. The amount of failed material was estimated to be in excess of two million tons. In order to ensure a safe working environment at the quarry a slope monitoring program was established in the area of the failure. The program consisted of using an EDM survey instrument to periodically measure the location of survey prisms installed at carious points on the north wall. The locations of the prisms were recorded over several months and changes in location were analyzed in order to identify and characterize the movement of the failed mass. The results of the analysis provided a basis for recommendations regarding access to various areas of the quarry. This paper discusses the factors contributing to the failure, the method of post-failure slope monitoring, anti the interpretation of the monitoring data.

Jan 1, 2002

By David P. Conover, Jake Bain, Christopher M. Ross

"Highwall mining of thick (up to 100 ft) steeply dipping (20° or more) coal seams provides many challenges, both geotechnically and operationally because seam dips near or in excess of highwall mining machine capabilities are encountered. Maximizing coal recovery while maintaining highwall stability requires innovative techniques with regard to web and barrier pillar layout, depth of penetration, and choice of mining horizon within the seam. Stability of highwall mining slopes, openings, and pillars are typically analyzed using the ARMPS-HWM program, as well as LAMODEL, UDEC, and Slope-W modeling. Highwall stability can be maintained and highwall mining production optimized by applying design criteria in creative ways, including alternating miner penetration depths and initiating mining of thick seams toward the bottom of the seam. Highwall mining of thick, steeply dipping coal requires careful planning and execution, including close cooperation between geotechnical design engineers, the mining company, and the highwall mining contractor. This paper describes the application of creative design techniques to a specific pit arrangement at the Westmoreland Kemmerer Mine, Kemmerer, Wyoming. Highwall mining was accomplished by UGM ADDCAR Systems, LLC, on a contract basis. INTRODUCTION Highwall mining is a technique for attaining additional coal recovery after the economic strip limit is reached in surface mining. It involves remote deployment of a continuous miner in openings beneath the final highwall, with no personnel entry. Many candidate areas for highwall mining have thick and steeply dipping seams. Mining downdip presents challenges related to the maximum pulling capacity of the machine, traction of the cutting head, and material conveying, all of which limit penetration depth. Maximum penetration is greater for flatter slopes and decreases for slopes nearing the threshold of the maximum machine operating angle. Most highwall mining operations are relatively flat with slight undulations within the seam; therefore, the highwall mining pillar design criteria applies fairly equally to the entire mining area. However, in steeply dipping deposits, design criteria based on higher overburden loads at the far end of the penetration are excessively conservative for the shallower portions of the openings near the highwall."

Jan 1, 2017

By Kanchan Mondal, Anthony (Sam) Spearing, Gopi Bylapudi, Joseph C. Hirschi

"The U.S. coal mining industry uses about 100 million rock anchors per year. ASTM F432 specifies the requirements for rock bolts on mines but does not address corrosion. Corrosion has been found to be an issue in Australian coal mines (Hebblewhite et al., 2003 and Villaescusa et al., 2007), where the problem has been researched and stress corrosion has been found to be a significant cause of rock falls. Corrosion is also a major concern for underground civil construction in the U.S. but has not been considered an issue or adequately researched in coal mines. Underground conditions are conducive to corrosion mainly because of water quality and humid conditions. There is a perception, however, that when bolts are fully grouted, adequate corrosion protection is offered to the steel. Research has shown that this is not necessarily the case, due to the formation of micro-cracks as the resin sets and with subsequent rock movement shearing the resin column. This paper outlines a method to determine the corrosion potential of bolts used in long-term excavations and suggests ways to mitigate such effects based on research conducted in the lab and on three mines.INTRODUCTIONResearch on rock anchor corrosion in mines has not been extensive enough in the past, and the effects of several factors in the mine atmosphere and waters are not clearly understood. One probable reason for this lack of research may be attributed to the time required for gathering meaningful data, which makes the study of corrosion quite challenging.Almost all the rock bolts used in coal mines are made from steel, hence the corrosion of iron needs to be understood. The corrosion of iron is an electrochemical phenomenon with the overall equation"

Jan 1, 2010

By Keith A. Heasley

Pillar recovery in deep coal mines with competent roof and floor can concentrate stresses and generate hazardous bumps. Actual calculation of the geologic strain energy released in association with these coal bumps has been rare, although energy release values have been utilized successfully for indicating burst potential in numerous hard- rock mines. This paper advances the current knowledge of energy release calculations as applied to coal bumps through an extensive analysis of an actual bump occurrence. The U.S.B.M, displacement- discontinuity code, MULSIM/NL, is used to produce a numerical model which generates stress, displacements and energy values associated with a pillar retreat section. This model is calibrated with actual field data, and then dissipated energy values from the model are examined as to their suit- ability for indicating bump potential. Ultimately, it is determined that prudent application of dissipated energy calculations can be used as a tool to investigate the coal bump potential of a mining plan or cut sequence.

Jan 1, 1990

By Nicole E. Evanek, Anthony T. Iannacchione

"Over the past 36 years, a great deal of information has been presented and discussed at the International Conference on Ground Control in Mining (ICGCM). The topic of surface subsidence engineering has resonated throughout each of the 36 conferences, producing 155 related papers. These papers have come from many countries. The major focus has been underground coal, especially longwall mining, but hard rock mining has also received attention. This impressive collection of reports presents a unique opportunity to reflect on the progress made towards understanding subsidence basin characteristics and developing methods to predict and mitigate its impact.In the initial meetings, the focus was on measuring subsidence and developing prediction methods. As understanding increased, predictive methods were developed and tested, especially in North America, China, Australia, Europe, and India. Efforts were made to understand how structures, aquifers, and surface waters were impacted by the formation of subsidence basins. As time progressed, the number of papers dropped slightly and became more focused on site-specific conditions. Most recently, advanced monitoring techniques have revealed new information, spurring a resurgence in research activity. Another recent focus has been on anomalous horizontal deformations occurring in sites with significant relief. Several reports from Australia and one from the US have brought this issue to light. In closing, all of these surface subsidence engineering papers have chronicled the maturing of this most important topic and, in the process, highlighted the importance of the ICGCM in the evolution of our current state of practice.INTRODUCTIONThe aim of this paper is to examine the role of ICGCM in 1) shaping our understanding of the mining induced subsidence phenomena, 2) developing tools to help predict its impact on the surface, and 3) evaluating controls to mitigate these impacts.This analysis involved the consideration of 155 papers available within the ICGCM conference proceedings and listed under the subsidence topic. Three of the papers where only available as abstracts and were not included in this analysis. Four other reports were focused on topics other than underground coal mining-induced subsidence issues and were also not included. It should also be noted that papers dealing with overburden behavior were not included in this analysis. As a result, 148 papers were reviewed and analyzed (Figure 1)."

Jan 1, 2018

By Khaled Morsy

Most of the available numerical codes simulating the reinforcing effect of fully grouted bolt are accomplished by a series of bar elements which are connected along their length to the host rock by shear springs and sliders. The spring-slider system represents the shear bonding effect between the bolt and the host rock. This paper describes a three dimensional finite element modeling technique for the 3D simulation of fully grouted bolt reinforcement. The proposed technique introduced a physical simulation for the fully grouted bolts. The bolt simulation is composed of a series of beam elements (representing the steel rebar) embedded in brick elements (representing the grout). Because of the complexity of the grout/rock interface, ABAQUS explicit code was used. A modification of the ABAQUS default friction model was conducted to consider the cohesion of the grout/rock interface. The interaction between the grout and the host rock is simulated by the modified friction model. To verify the proposed technique, a simulation of the pull out test we conducted. The results from the simulation were compared with former studies

Jan 1, 2004

By Behdeen Oraee-Mirzamani

Tunnel stability has an important role in the production process of an underground coal mine. There are various methods for analysing tunnel stability, such as numerical methods and analytical methods. In this paper, numerical methods (Phase2 software) have been used to determine tunnel wall displacement in a mining tunnel of the Parvade underground coal mine. The Ground Reaction Curve has also been drawn using analytical methods to determine tunnel wall displacement. The comparison of results from the numerical method and the analytical method show a noteworthy difference in the tunnel wall displacement. The displacement calculated by the numerical method shows a lower value than that of the analytical method because the numerical method is more suited to modeling the various coal and rock layers, as well as the shape of the excavations found in coal mines. The methodology used in this paper together with the results obtained from both methods can serve as useful tools for the coal mine design engineer when determining the ground support requirements.

Jan 1, 2013

By John G. Oldsen

Passive cable bolting and active cable trusses have been used in roof support for more than two years Excellent roof control has been experienced by many coal operations. This paper covers the new and innovative developments in cable support systems and their application in mines. Multiple cable bolts, tensioned cable bolts, coal rib wrapping, and other cable applications will be covered.

Jan 1, 1997

By Yoginder Paul Chugh, Jason E. Tinsley

"Over the last five years, the authors have compiled a database of Short Encapsulation Pull Test (SEPT) evaluations from Interior Basin (Basin) coal mines. Typically, SEPT data are analyzed to obtain peak load carrying capacity per unit length of resin encapsulation designated as the ""Grip Factor,"" or GF. In a previous paper, ""An Analysis of Short Encapsulation Bolt Pull Test (SEPT) Data From Interior Basin Coal Mines,"" authors analyzed tangent value of the load-displacement curve as Anchorage Stiffness at 50% (AS-50) of the peak load, or GF value, to assess reinforcement potential of an installed bolt system. This paper attempts to correlate the secant AS VALUES (of SEPT on 6 ft (1.8 m) long installed bolts at a lower load of about four tons from several different mines in the Basin with their MSHA-approved primary support requirements. Since the current regulatory environment requires plan changes dynamically to ensure that roof falls are minimized, the authors hypothesize that the practiced roof control plan must meet the minimum requirement of adequately supporting immediate roof strata. The analyses are based on 181 SEPT studies performed by Minova professionals. Analyses indicate a macrolevel correlation for both roof support density and roof support cost that may have the potential to be used by mine operators to compare their performance with other mines in the area. Limitations of the analyses include ignoring mining depth, mining height and required secondary supports as part of the requirements for a roof control plan. The authors recommend additional analyses to develop this concept further to develop guidelines that can be confidently used by coal companies.INTRODUCTIONPartially- and fully-grouted bolts are extensively used in coal mines for roof support as part of MSHA-approved roof control plans. Since grouted bolts have a larger area of contact with the rock, they can develop much greater anchorage capacity than conventional expansion shell (point-anchored) bolts. Load transfer characteristics and interaction mechanics between steel rebar, grout and rock mass around the bolt hole for grouted bolts are generally assessed in the laboratory or field though short-encapsulation pull tests (SEPT), which have been extensively researched by Aziz and Jalalifar (2005), Aziz (2004a), Serbousek and Signer (1987), Signer (1990), and Mark et al. (2002), among others. In a SEPT, about 12 in. (30 cm) of bolt length is typically encapsulated in resin and a pull test is performed to collect load-displacement data prior to failure and, in some cases, post-failure. A typical load-displacement data set for a bolt is shown in Figure 1. SEPT characteristics are designated by peak load carrying capacity, or grip factor, which is the peak load carrying capacity per unit length of resin encapsulation. SEPT is routinely used to assess anchorage performance characteristics of different lithologies overlying a coal seam to identify type of bolt, bolt diameter, length and spacing across and along an excavation. Anchorage stiffness, or AS, at any load may also be calculated as the tangent or secant value of the slope of the load displacement curve at a particular load level. Anchorage Stiffness characteristics of bolts from SEPT data have typically not been considered in any depth until recently (Chugh et al., 2014; Chugh et al., 2015)."

Jan 1, 2016

By G. R. Corbett

Between 1977 and 1984, No. 26 Colliery, at Glace Bay in the Sydney Coalfield, suffered from a series of 37 rock/gas outbursts. These events were characterized by the complete pulverization of a sandstone which was propelled into the mine roadway and an associated release of methane gas. The events began to appear at a depth of 700 m and increased in intensity and damage to the excavation as the mining depth increased. At the time of the closure of No. 26 Colliery (as a result of an unrelated fire), these outbursts were the subject of intensive investigation. Although No. 26 is now closed, there is concern that similar events could appear at Phalen Colliery where current development work is proceeding at a depth close to the 700 m threshold. Past investigations into rock/gas outbursts included studies of in situ stresses, the simulation of outburst events in the laboratory, investigations into the potential for destressing an& degassing of problem sandstone and the development of numerical models to assist in the design of openings in outburst prone ground. However, despite this work, methods of predicting outburst conditions are presently limited to examination of probe hole cores for core discing, and methods of working under such conditions are limited to boring and firing and using volley firing techniques to initiate any outbursts while workers are safely out of the heading. During this investigation of worldwide occurrences of this phenomena, literature obtained suggested that outbursts might generate microseismic precursors. An intrinsically safe (IS) microseismic monitoring system was designed and developed based on CANMET's rockburst monitoring system currently in use in hardrock mines, and installed in a development roadway at the deepest extent of the Phalen Colliery. The system will record microseismic activity associated with development work to try to identify characteristic precursors of outburst-prone conditions. This paper describes the steps taken to identify a microseismic system suitable for use at Phalen colliery, of which part of the requirement was that it be IS and approved for use in the Sydney Coalfield. The modifications to the selected system are described, along with its capabilities and the preliminary results of its performance over the first few months of use.

Jan 1, 1994