Search Documents

By Richard Kastner, Emilie Vanoudheusden, Fabrice Emeriault, Jacques Robert

INTRODUCTION The subway line B of Toulouse (France) has been realized with three different tunnel boring machines (TBM) techniques: Contracts 2 and 5 are excavated with earth-pressure balanced TBM, Contract 4 with a slurry shield TBM, and Contract 3 with a compressed-air TBM. The first three machines are around 7.7 m in diameter, while the last one is 5.3 m. Moreover, a small part of the line (50 m) has been excavated by a conventional method. The tunnels run through the Toulouse molasses, composed of hard sandy clay with pockets and lenses of dense sand. Geotechnical investigations have shown that in these formations, K0 is greater than 1, around 1.8 at a depth of 25 m (Serratrice,2005) and that geotechnical characteristics are homogenous on the whole layout (? =22 kN/m3, Su = 300 kPa, c' = 30 kPa, F' = 32°). The water table is found between 2 and4 m below ground level. As geology, stratigraphy and tunnel cover (between 10 and 20 m) are almost identical, a comparison of movements induced by the excavation by each of the four excavation techniques is possible. This paper presents the soil mass movement measures in the case of the conventional excavation method and in the case of TBM sections. It shows how tunneling parameters may explain the different surface movements observed during excavation. For the sake of simplicity, only the results of Contract 2 (earth pressure balanced TBM)will be presented. MONITORING Monitoring for the Conventional Method Section For the conventional method section (Vanoudheusden et al. 2005) the mass soil movements are measured with two inclinometers and one multi-point extensometer borehole with automatic data acquisition (Figure 1). The monitoring devices include

Jan 1, 2007

Introduction Aggregate mining impacts on water resources are a source of concern to local governments. To evaluate those impacts, the Minnesota Department of Natural Resources conducted a four-year study at three gravel pits (two alluvial and one beach-ridge) and five quarries (flat-lying Paleozoic limestone). This research provides the first comprehensive look at aggregate mining impacts on ground-water systems in Minnesota. The results will be used by government officials making permitting decisions about aggregate operations and by responsible owners of aggregate mines as they plan their operations to avoid conflicts with neighbors and with resources dependent on ground water and surface water. Natural aggregate (crushed stone, sand, and gravel) is a vital part of our economic infrastructure in Minnesota. Aggregate is used for road and bridge construction and in a variety of building materials. In 2003, the value of construction sand and gravel and crushed stone in Minnesota was approximately $245,000,000. As Minnesota’s economy continues to expand, the demand for aggregate will continue to grow. Sand and gravel pits are located in every county in Minnesota. In 1990, the Minnesota Department of Natural Resources, Division of Minerals (DNR Minerals), estimated the number of active and inactive operations at 1500 with the view that this number was likely too low. Quarries for mining limestone, dolomite, sandstone, and hard rock (granite and quartzite) are found in 34 counties. A 1990 DNR Minerals inventory found 165 active operations, 88 percent of which were limestone quarries (Nelson and others, 1990). That same inventory counted 1,367 inactive operations, 70 percent of which were limestone quarries. Aggregate mining is an extractive use of resources: mining alters the landscape and its natural hydrologic system. When a new pit or quarry is proposed or when an existing operation needs to expand, local governments and citizens typically have many questions about the impacts mining might have. Local governments, which are responsible for reviewing these operations, rarely have the budgets to hire experts to evaluate potential impacts of quarry and gravel pit proposals. The Minnesota Legislature’s Aggregate Resources Task Force identified that local government units (LGUs) often lack the expertise to assess ground-water models (Southwick and others, 2000).

Jan 1, 2007

By MEHMET KIZIL, PETER KNIGHTS, ROYAL REA

A 1/20 scale experimental dozer push test rig was designed and constructed to quantify the expected production rates (loose cubic metres per hour) for dozers operating in hard rock bulk push applications. The particle size distribution of the material employed in the test rig was modelled on a fragmented muckpile representative of that for a typical surface copper/gold mine overburden. A commercially available road base material was found to be highly representative of site conditions. Buckingham Pi theory was applied to mathematically develop factors for scaling up dozer productivity parameters, including blade loads and push times. Dozer production rates were investigated for various dozing distances and slope angles. A series of instantaneous productivity curves were produced which are applicable for use in hard rock dozer push operations. Currently, it is difficult to estimate dozer push productivity in hard rock environments due to dozer productivity correction factors that are empirical in nature and provide only discrete, end-point values for a range of operating conditions. The productivity curves produced demonstrate that dozer productivity declines rapidly over the range of 10 m to 40 m. As such, it is recommended that efficient bulk dozing operations in hard rock mining blocks should not exceed 40 m dozing distance. Further testing of muckpile conditions with increased clay and moisture content would be beneficial in order to better understand and quantify the effects of cohesion on hard rock dozer push productivity.

Nov 23, 2021

In 2005, CANMET-MMSL used its pool of expertise in ground control, open pit and underground mine engineering, mineral processing, information technology and applied mineralogy to launch a mine-to-mill research project. The objective of the project was to optimize the distribution of rock breakage energy among blasting, crushing and grinding activities, thereby maximizing the efficiency of energy utilization within comminution processes. Tests were designed to demonstrate that this approach could reduce energy consumption, thus contributing to the reduction of green house gas (GHG) production in the Canadian mining industry. The project was accomplished in collaboration with DynoConsult and Dyno Nobel Canada Inc., a world leader in commercial explosives. Data analysis from 12 blasts (six with electronic and six with pyrotechnic detonators) in three different geological formations of a quarry (soft, medium and hard rock) shows that electronic blasting technology increases rock fragmentation by 15% (in hard rock) to 20% (in soft rock). A more uniform rock fragment size distribution is also obtained. The impact of the improved quality blast product on downstream processes of the quarry is a productivity increase of 5% in rock excavation and transportation, an energy reduction of 10% at the primary crusher and an increase of 15% of the primary crusher throughput. Extended to the Canadian mining industry, such results would represent a GHG emission reduction of about 0.05 Mt/y. A soft-sensor prototype, based on primary crusher data (i.e., energy consumption, throughput, feed and product size distribution) and a simplified computerized process model, was developed for on-line measurement of the rock operating work index. Additionally, 385 rock samples and specimens were collected and prepared to determine the tensile and compressive strength of the rock material, to evaluate the aggregate crushing work index and to examine the development of micro- and macro-fractures by means of binocular and SEM microscopy. Blast-induced rock damage was evaluated at the end of the laboratory-testing program. Even though a reduction of rock hardness of around 30% was observed after blasting, the impact of the blasting method (i.e., use of electronic or pyrotechnic detonators) on the induced rock damage could not be observed. It is either absent or not perceptible with the accuracy of the measuring techniques and the number of samples analyzed.

Jan 1, 2008

By M. Martins

This work presents and discusses the influence of the surface tension (gLV) of methanol/water mixtures on the flotation response of apatite versus gangue minerals conditioned with flotation reagents (75 g/t cornstarch and 100 g/t Berol 867) at pH 10.6. Berol 867 is a collector composed of sodium alkyl sarcosinate plus nonionic surfactant. The highest Schulz efficiency of separation (recovery of apatite minus recovery of gangue) was achieved at ?51.0 mN/m. The critical surface tension of wettability (gC) of apatite was found to occur at 34.7 mN/m when determined by means of gamma flotation experiments, and it was 33.9 mN/m when determined by Zisman?s approach.

Jan 1, 2009

By J. D. Miller

Characterization of feed material with respect to expected concentrate grade and recovery is fundamental to the design of improved separation efficiencies and to achieve sustainable development in the utilization of our mineral resources. An important reference point for this characterization is the liberation-limited grade/recovery curve which represents the perfect separation, the best separation which can be achieved for a given feed material limited only by the extent of liberation. Now, liberation-limited grade/recovery curves can be determined based on 3D mineral liberation analysis of feed material. Thus, actual separation efficiencies can be compared to what might be expected for a perfect separation limited only by the extent of liberation. It is shown that 3D mineral liberation analysis based on X-ray micro CT (XMCT) is preferred to 2D section analysis which overestimates the extent of liberation. By way of example, procedures and experimental results are presented and discussed for feed material in the case of phosphate rock flotation.

Jan 1, 2009

By T. G. Rozgonyi

The basic goal of this investigation was to determine the degree of drying of high moisture lignite through the use of high temperature and pressure steam autoclaves. Specific items studied were: a) the effect of lignite particle size, b) steam temperature and pressure required, and c) the time of ahydration. Although removal of sodium, ash, sulfur and other ash-forming minerals was not the goal of this study, basic analysis of effluent water showed organic material and alkalai metal content. Removal of inherent moisture from run-of-mine lignite was tested by lock-feeding the lignite, which was previously sized by screening into 25 kg autoclaves. High pressure, up to 4.053 MPa (588 psi), saturated steam was then introduced into the pressure reactor. Reaction time, pressure, temperature, and depressurization rates were strictly controlled for each reactor test run. Results indicate that about 80% of lignite total moisture was removed, including some of the inherent moisture, yielding a non-oxidized, and thus stable, lignite product. As stated, a side benefit occurred as some reduction of non-combustible portions of the lignite also took place. The conclusion reached as a result of the tests is that the steam-drying process can be successfully applied to reducing moisture in lignite, and may be considered for additional studies on acceleration of the coalification process. On the basis of the data presented, the author believes that lignite can be economically upgraded in steam autoclaves by simultaneously reducing the moisture content by 80 percent and the sulfur content by at least 50 percent. Upgrading the lignite by this method will result in large energy and financial savings.

Jan 1, 1984

By J. Noll

Many underground metal/nonmetal mines are using enclosed cabs on mining equipment to reduce the exposure of miners to diesel particulate matter (DPM). However, some enclosed cab systems may not be meeting their expected efficiency in capturing DPM, which could be a result of inappropriate filter use, cab leaks, or insufficient pressurization. NIOSH investigated several types of filters for reducing DPM to determine which type had the best capture efficiency. The laboratory results indicated that a MERV 8 (Minimum Efficiency Reporting Value, as defined by the American Society of Heating, Refrigerating and Air- Conditioning Engineers) filter captured about 50 percent of the DPM, a MERV 16 filter collected 96-98 percent of the DPM, and two HEPA (high efficiency particulate air) grade filters captured over 99 percent of the DPM. NIOSH also performed a field study to measure the efficiency of two cabs at a limestone mine. The cab filtration systems of a loader and haul truck were found to be over 90 percent effective in removing DPM except under certain operating conditions when the efficiency was as low as 41 percent. Evidence seems to suggest that these conditions were when a window was open in the cab.

Jan 1, 2011

By N. M. Can

The effects of microwave treatment on the floatabilities and magnetic susceptibilities of some sulfide minerals, namely, pyrite, chalcopyrite, galena and sphalerite, were studied. Pure mineral samples were prepared in -425+212-µm, -212+106-µm and -106+38-µm size fractions. Microflotation and magnetic separation tests were carried out on the samples after microwave treatment at 600, 950 and 1,300 Watts for 5, 20, 60, 90, 120 and 240 seconds. The maximum temperature values of the samples were measured during the microwave treatment, and possible altera-tions on the mineral surfaces were determined by X-ray diffraction (XRD) analysis. The effects of microwave treatment are discussed based on the result of microflotation and magnetic separation tests. The results revealed that pyrite, chalcopyrite and galena were heated very quickly and that their surface temperatures reached ~700° to 900°C, while the temperature of sphalerite reached only ~130°C. The floatability of pyrite, chalcopyrite and galena were decreased when microwave energy and the duration of treatment were increased, owing to oxidation of the mineral surfaces caused by relatively high temperature. As expected, there was no change in the floatability of sphalerite. The magnetic properties of pyrite and chalcopyrite were improved by the increase in microwave energy and the duration of treatment to such an extent that 90% of the feed separated as magnetic product. But no change was observed in the magnetic properties of galena and sphalerite.

Jan 1, 2007

By P. A. Hagerty

Biological treatment of metals-impacted water using sulfate reduction is a viable means of treatment that has been applied in pilot and full scale at numerous projects. One of the fundamental challenges with this type of treatment is the selection of an appropriate substrate to support the sulfate reduction process long-term. The substrate degradation products provide a carbon source and an electron donor for metabolism by sulfate-reducing bacteria and consequently organic characteristics are critical; however, the physical attributes of the substrate are equally critical to an efficient and optimized substrate mix. This paper explores the affect of particle size (a.k.a. grain size) of several substrate mixes on the treatment efficiency of sulfate reducing treatment systems. Substrate selection can be separated into two phases of evaluation, the primary selection phase and the secondary optimization phase. The primary selection phase considers such fundamental attributes as source availability, economics, bioavailability and longevity. These fundamental activities are conducted in order to identify potential candidate ingredients of the substrate mix which are regionally available, economically viable and consistent with the biogeochemical aspects of the project. Recent work has been conducted in the development of testing protocol for organic substrates to quantify bioavailability (Martinez Hernandez et al. 2010, Place et al. 2006) as part of the primary selection phase. Once the substrate ingredients have been selected based on the primary criteria, the mixture of these ingredients is then developed based on an optimization process, including consideration of the substrate ingredient?s particle size distribution.

Jan 1, 2011

By L. C. Stone, J. C. Parr, T. N. Anderson, D. Metcalf

An increase in the importance of low-grade materials as sources of gold and silver has led to the need for improved analytical methods on leach solutions, ores and various effluents, residues, and in-process streams. These are required by plant operators as guides to process control and for accounting pldrposes. Atomic absorption spectrophotometry (AAS) and AAS preceded by pre- concentration have been applied successfully to resolve many such problems. However, AAS is no panacea and imprecision or loss of accuracy can result if adequate precautions are not taken to prevent losses and eliminate interferences. The recent methods are discussed together with methods for overcoming difficulties. Comparisons with more classical analytical techniques are also given.

Jan 1, 1981

By Scott Ellenbecker

The formation in Newmont Mining?s Phoenix Mine near Battle Mountain, NV contains high levels of abrasive quartzite as well as gold, copper and silver. Newmont started mining operations at Phoenix (formerly Battle Mountain Gold) three years ago and the planners knew they were working with a challenging geological formation. But as it turned out, it was more challenging than anticipated. Mine manager Mark Evatz said, ?Anything that touches Phoenix rock wears fast. The rock fights back here.? To contend with the hard conditions, Newmont uses Atlas Copco?s Pit Viper 271 (PV-271) blasthole drill. Because of the hardness of the rock, drilling at Phoenix requires hammer drilling and the mine uses Atlas Copco TD65 hammers with 171 mm (6.75 in.) bits. The mine?s PV-271?s are outfitted with a single 41 m3/min (1450 cfm), 2.4 MPa (350 psi), oil-flooded air compressor. Phoenix has six Atlas Copco PV-271 drill rigs plus an Atlas Copco DML and a DM45 midrange blasthole rig. The mine?s goal is to keep 3.6 Mt (4 million st) of muck in inventory to stay ahead of the shovels and support needed operational flexibility (ore control related). Drilling efficiency has been a continuous point of improvement since operations began at the mine. The single-pass depth capability of 16.5 m (55 ft) on the PV-271 helped with that. Originally, the plans called for 6-m (20-ft) bench heights, supported by 7-m (23-ft) drill depths, and time spent moving from hole to hole was eating up productivity. Drilling on that plan resulted in drilling an average of 14 m/h (47 ft/hour). When depths were changed to 13-m (44-ft) drill depth, supporting blasting of 12-m (40-ft) benches, they were able to use the single pass capacity of the PV-271. Performance increased to more than 18 m/h (60-ft/hour) an hour. Although the drill depth change largely supported the improvement, other aspects of continuous improvement associated with improved knowledge of the Pit Viper drills helped as well.

Jan 1, 2009

By C. Sykes, E. Turner, M. Wyart-Remy

This paper follows that of the Milos Conf, 2002 and examines the collection and reporting of SDIs in the industrial minerals industry in Europe. It compares the characteristics of the GRI Reporting Guidelines, with its Metals and Mining Sector Supplement with those of the EU DG Enterprise Scheme, launched in 2001. The particular issue of SME's and companies which are not publicly traded is examined. The pros and cons of participating in such schemes is a central theme of the paper. The paper concludes that there and many business benefits for these companies in participating and submitting their data. The European Commission Scheme is strongly recommended for companies in the sector which are SME's and not-publicly traded as well as large firms who are listed on European Stock Exchanges.

Jan 1, 2005

By A. Nieto

A dump edge and vehicle proximity warning system is being developed at the Colorado School of Mines using GPS and wireless local area networks to improve the safety of off-highway trucks in open pit mines. After two years of research, software development, and testing in the laboratory, field tests are currently being carried out at operating limestone quarries and open pit mining operations to evaluate the effectiveness of the system under rugged operating conditions. This paper describes the progress made on this NIOSH-funded project and discuss, tests carried out recently, at the Morenci open pit copper mine in Arizona.

Jan 1, 2002

By R. Karl Zipf

Highwall mining is an important surface coal mining method, and it may account for approximately 4% of total U.S. coal production. Highwall stability is the major ground control related safety concern. Ground control plans for highwall mining should specify hole width, web pillar width, barrier pillar width and number of holes between barriers. This paper offers simple design charts for these parameters aimed at providing “ball park” checks. Web pillars containing pre-existing auger holes are analyzed and a design chart for estimating their minimum width is also presented. Finally, close proximity multiple seam highwall mining, which may have caused several serious highwall failures, is analyzed. Web and barrier pillar recommendations for this special situation are presented.

Jan 1, 2005

By J. Torma-Krajewski, C. Hipes

Many mining companies apply ergonomic principles, but it is done either informally and/or reactively. Examples of an informal approach include replacing worn equipment, such as seats, with models that have ergonomic features, or modifying tasks to eliminate safety hazards that will also reduce risk factor exposures that may result in musculoskeletal disorders (MSDs). A reactive approach is followed when modifying a task/equipment after an MSD occurs. Neither one of these approaches involves a systematic method of proactively applying ergonomic principles to actually prevent injuries or illnesses. This paper will discuss how Vulcan Materials Company applied ergonomic principles and the interventions implemented to reduce risk factor exposures.

Jan 1, 2007

By Walter R. Hibbard

Precipitation in the northeastern United States, Florida, California and in many industrialized areas of the world is now more acidic (lower pH) than can be accounted for by natural causes. At the same time, the acidity of many lakes and streams in the northeastern United States has been measured and found to be similar to that of actual rain. These facts have led to conclusions that the two conditions are related. Coal burning utilities, 700 to 1000 miles upwind, have been accused of being the cause, leading to proposals for strict emission controls on the alleged offenders. The costs of these controls would place an estimated $10 to $15 billion capital burden on utility customers in about 15 states plus $2 to $6 billion annual operating costs. There appears to be no direct well-established scientific evidence that the accused are guilty but that the indictment is based largely on circumstantia1 evidence. This study examines the evidence, describes the situation and proposes what must be done to reduce the acid precipitation in an orderly cost beneficial manner. It is interesting to observe that studies by the different adversaries on the acid precipitation issue come to different conclusions largely because they do not read the same literature, but selectively develop evidence to support their own points of view, This study will try to review the issues impartially and reach a position of scholarly balance.

Jan 1, 1982

By Tony Peglas, Harry Asche, Eva Wood

The North-South Bypass Tunnel is a new $AUD1.5 billion underground traffic route in Queensland, Australia, a project of the Brisbane City Council. The tunnel is approximately 5.2 km long, bypassing the Central Business District, and is adjacent to and below major buildings and services. Road tunnel alignment issues include the complex southern connections to the Pacific Motorway and the design of ramps to the east and the north. A review of road tunnel alignment criteria and accident data for Australian and overseas tunnels, similar to the proposed NSBT, are discussed. The key findings of this review lead to a rationalization of the traditional tunnel cross sectional width allocation. The road alignment design elements adopted for the NSBT are also discussed. The NSBT route crosses beneath the Brisbane River. Geotechnical investigations and hydrogeological modelling are described. The crossing has a fundamental impact on the alignment and the tunnelling methods. The tunnelling methods to be adopted and the tunnel support are described. The geotechnical investigations and hydrogeology analysis culminate in the selection of a single shielded TBM for the reference design. These outcomes are related to complex issues of hydrogeology and contaminated groundwater. These are discussed in detail.

Jan 1, 2005

By T. C. Souza Pinto

Because shape is an assessment of the three-dimensional form of a particle, it may be described in terms of sphericity (?), which is a measure of how closely a particle approaches a spherical configuration. In this study, Darcy?s law and the Kozeny-Carman model for fluid flow through porous media were applied to packed beds to determine the sphericity (?) of apatite particles. The beds were composed of glass spheres or particles of apatite (igneous from Brazil and sedimentary from the United States) of three classes of size (Class 1: -297 +210 µm; Class 2: -210 +149 µm; Class 3: -149 +105 µm). Glass spheres were used to validate the model because of its known sphericity (? = 1.00). Apatite particles, either igneous or sedimentary, showed very close values for particle sphericity (? ? 0.6). Observations on particle images conducted by scanning electron microscopy illustrated that igneous (? = 0.623) and sedimentary (? = 0.644) particles of apatite of Class 2 predominantly exhibit elongated shape. The close value of particle sphericity (? ? 0.6) showed by either igneous or sedimentary apatite may be justified by the similarity in particle shape.

Jan 1, 2009

By Jonathan Taylor, Irwan Halim, Frederick (Rick) Vincent

The new underground facilities for the LINAC Coherent Light Source project at the Stanford Linear Accelerator Center in Menlo Park, CA, are constructed in very weak sedimentary rock interspersed with uncemented zones. In addition to several 21-footwide (excavated) tunnels, the NATM excavations include a large, 49-foot wide (excavated) cavern, an unprecedented size in this geology. The critical design issues include characterization of the weak rock, some shallow rock cover areas, and very stringent criteria for final invert slab movements within the tunnel. The design also incorporated severe seismic criteria, since the site is in close proximity to the San Andreas Fault.

Jan 1, 2007