Search Documents

By Myles E. Robinson

During the last decade there were pronounced changes in the competitive pattern of the fossill fuels It is proposed to trace these trends and describe inter-fuel competition, first as it relates to the economy as a whole and then more specifically to examine competition of the fossil fuels as these share the electric utility market. Table 1, Competitive Fuels and Water Power Used in the United States, 1950-1959, shows the growth in the consumption of coal, oil, gas and water power 'during the past decade. Uses which are not directly competitive among the fuels, such as tractor fuel, carbon black, and consumption of petroleum products in the making of synthetic rubber, have been excluded from these statistics. The experience of the three fossil fuels in competition since 1950 shows natural gas expanding more rapidly, than oil by roughly twice as much, 219.0 percent' compared to 124.1 percent growth in B.t.u.s of oil consumed in the ten-year period. Percentagewise, water power little more than held its own, and coal, including anthracite, actually decreased more than one-fifth.

Jan 1, 1961

By John E. Urosek, Jack E. Tisdale

The Mine Safety and Health Administration (MSHA) has developed a Mine Ventilation Bleeder and Gob Training Course. This three day course is designed to increase the knowledge and understanding of bleeder ventilation systems. It discusses concepts, designs, plan approval, inspection and evaluation of bleeder systems. This paper will introduce some of the material contained in that course, focusing on the inspection, examination, and evaluation of bleeder systems. The regulations addressing the use of bleeder systems are found in Title 30 Code of Federal Regulations (30 CFR) Section 75.334. The examination requirements are found in 30 CFR Section 75.364. Section 75.364 de- scribes specific locations where examinations are to be made and specific information to be gathered at those locations. The required locations and information will be discussed in some detail with examples and illustrations. These weekly examinations for bleeder systems are designed to monitor the parameters of the bleeder system and to evaluate its effectiveness. Over time, conditions can develop in the bleeder system that affect the ventilation and lead to hazards such as methane accumulations. The hazards of methane accumulations need to be understood as such accumulations can contribute to mine explosions. The importance of additional information gathered by the mine examiner that can assist in evaluating the performance of the system will also be discussed.

Jan 1, 1997

By John Hanna

Over the years the coal industry in Alabama has generated about 150 million tons of fine waste coal, increasing at a rate of 2 million tons/year, during mining and cleaning operations. Reclamation of the fine-size wastes containing 20-60% by weight clean coal provides, free of charge, mined and crushed feedstocks for coal recovery and eliminates a major source of acid water pollution. Tests were made on the impounded wastes and current plant discharges to recover the coal fraction by sizing, gravity and flotation techniques. Gravity separation of the plus 100 mesh material produced commercial grade coal averaging 8.2% ash, 0.8% sulfur and 13,350 Btu/lb. However, the coal recovery was relatively low at 50-65%. Froth flotation using mechanical and froth column methods gave similar coal products at much higher coal recovery of 87-93%. The coal produced analyzed 10% ash and 1.1% sulfur.

Jan 1, 1991

By R. R. Beebe

Marcona Corporation produces about 3.5 million long tons of iron ore pellets annually on its two travelling grate pelletizing machines at San Nicolas, Peru. During 1969, these pellets will be shipped to customers in four marketing areas--Japan, the United States, Europe, and South America. All of these sales are on the open market, and product quality is a major concern. Typical chemical, structural, and quality test results for Marcona pellets are given in Table 1. [ ]

Jan 1, 1969

By J. Engesser

A research project supported by the Minnesota Department of Natural Resources and the Iron Ore Cooperative Research Committee was undertaken to reduce the dissolution of fluoride into process water during taconite processing. Leach tests were conducted using rod mill feed samples and water containing varying concentrations of calcium and sodium. Laboratory liberation grinds were performed to evaluate fluoride rejection during grinding and magnetic separation. Tube furnace tests were conducted to evaluate fluoride volatilization during pellet induration. The results indicate that fluoride concentration of process water is a function of both calcium and sodium concentration in process water. It appears that less than 1 percent of the fluoride present in rod mill feed will dissolve in process water during grinding. More than 90 percent of the fluoride present in rod mill feed is rejected with tailings during size reduction and magnetic separation. The furnace tests demonstrate that bentonite and fluxstone (calcite and dolomite) addition to taconite concentrate during pellet production increases the amount of fluoride that volatilizes during induration. Lime hydrate addition to pellets decreases the amount of fluoride that volatilizes during pellet induration. During acid pellet production approximately three times more fluoride enters the water during induration-off-gas scrubbing than during grinding. When fluxed pellets are produced three to eight times more fluoride enters the water during off-gas scrubbing than during taconite grinding.

Jan 1, 2004

By F. H. Deily

The petroleum industry has developed and utilized many aspects of rock mechanics, both in its search for petroleum and in its drilling and production operations. Geological exploration activities have been improved by knowledge of earth tectonic forces. Better understanding of seismic wave motion has contributed to a more accurate interpretation of geophysical data. Drilling activities have benefited from basic knowledge of rock strength behavior under in situ conditions. Production has been significantly increased through stimulation techniques, such as hydraulic fracturing. The ability of rock mechanics work to contribute to future petroleum activities will depend upon the development of knowledge of rock properties under greater depths and at higher pressures and temperatures.

Jan 1, 1969

By C. G. Carlström

The total iron ore production in Sweden in 1969 was 33.3 million metric tons. 31.7 million tons were exported mainly to Western European countries. 27.8 million tons (87 per cent) originated from the mines at Kiruna, Svappavaara and Malmberget, located just north of the Arctic Circle in Sweden. Planned production for 1970 is 25 million tons during 10 months, due to a strike at the beginning of the year. Present production plans for the next five years expect an annual export capacity around 33 million tons in 1975, including 5.7 million tons of pellets. The mining and shipping at the loading terminals of Narvik on the Atlantic coast and Luleå at the Gulf of Bothnia are managed by LKAB - a 96 per cent state-owned company. 4 per cent of the share capital is owned by the private Grängesberg Company. The railway - 106 miles from Kiruna to Narvik and 130 miles from Malmberget to Luleå - is operated by the State Railways in Sweden and Norway. Comprehensive expansion of the Narvik ore port will be carried through during the next five years to increase the annual shipping capacity to at least 35 million tons and meet the development of rapidly growing ship sizes.

Jan 1, 1970

By Sam Rosenblum

The anomaly ratio is obtained by dividing the analyzed value of an element by the anomaly threshold value of the element. The sum of anomaly ratios for all anomalous elements in a sample may be compared with similar sums for other samples, so that the samples having the greatest anomaly-ratio totals can be recognized easily. In partial or full-suites-of-ore-elements the use of anomaly ratios is more meaningful than analyzed values because the ratios quickly indicate anomalous elements and call attention to samples and localities that should be investigated.

Jan 1, 1980

By P. Berendsen

Structures along the rift were subjected to episodic reactivation. Major north-northeast-trending high-angle normal or reverse faults and northwest-trending trans-current fault systems, may exercise control over ore-forming processes. Gabbro and basalt are the dominant igneous rock types. Carbonatite and kimberlite occur in Nebraska and Kansas. Concentrations of Cu, Ni, Co, Ti, Au, Ag and PG-minerals are known to occur in this setting Arkosic sandstone, siltstone, shale and minor carbonate units occur on top of the rift basalts and in flanking basins where they may reach thicknesses of 10 km. The potential for stratiform or unconformity-related metal liferous deposits must be considered.

Jan 1, 1986

By E. J. Onuscheck

With passage of the Federal coal' Mine Health and Safety Act of 1969, many challenges have been directed to the industry's mining and safety engineers. The most critical challenge is that of ventilation. The language concerning ventilation in many sections of the Act could very well deprive or limit the mining engineer in planning the ventilation for new mines, since the Act requires federal approval of all ventilation plans. Dependent upon approval and of course application of the law, this could, due to economics, prohibit the opening of new mines in some cases. Petitions for modification of some mandatory standards relating to ventilation have already been filed under Section 301(c). It is quite possible that many of these standards may be modified.

Jan 1, 1970

By Paul Eimon

The 1981 Fall field trip of the Denver Region Exploration Geologists' Society focuses on Creede. That is appropriate - because significant mining history has been made and is being made in this off-the-beaten track, high-country mining district. Creede is one of the few Colorado bonanza towns which was big in the 19th Century, had its ups and downs, and produced almost continuously since its discovery. Creede is important to geologists for its: precious and base metal production, current exploration activity, and research into near-surface hydrothermal systems. United States Geological Survey research and field geologists zeroed in on Creede some 25 years ago and their steady, consistent work is now being spotlighted and appreciated.

Jan 1, 1981

By Pramod C. Thakur

During the past ten years, the US coal industry has experimented with various ways to extract methane from coal seams. Drilling long horizontal boreholes in solid coal from mine workings and vertical gob degas boreholes are becoming standard techniques for methane recovery from coal seams. Prime motivations for such work have always been safety and productivity in mines, but the commercial value of gas so produced is encouraging utilization. The paper reviews various ways to produce methane from coal seams and discusses some utilization projects extant in the industry.

Jan 1, 1984

By Jeroen van Eldert, Daniel Johansson, Henrik Ittner, Håkan Schunnesson

"Numerous aspects of underground construction, from structural stability to construction costs, depended on the tunnel quality, including blast damage and the Excavation Damage Zone. Accurately quantifying the extent and severity of damaged rock is a problem. Recent technical developments in the field of Measurement While Drilling (MWD), including software for on-board logging and on-site analysis, have shown potential for rock-mass characterization. Ground Penetrating Radar (GPR) and P-wave velocity measurement have also improved and show similar potential. This paper explores the use of MWD, GPR and P-wave velocity measurements and uses them in techniques for excavation damage characterization and prediction. The paper is based on data collected from a small underground waste-collection site in central Stockholm, Sweden. The data is correlated against rock-mass characteristics and their responses are evaluated. Results indicate potential for excavation damage characterization for all tested techniques, which could minimize blasting damage and improve the over-all tunnel quality. 1 INTRODUCTION During underground excavation the rock mass is influenced in many ways. The Excavation Damage Zone (EDZ) is a result of these influences. The EDZ can be defined by an irreversible change in rock mass properties, for example increased permeability. EDZ is influenced by the excavation method, the rock mass properties and the in-situ stresses in the area of the tunneling. Since the 1990s research has been done on the EDZ by Emsley et al. (1997), Christiansson et al. (2005), Olsson et al. (2009), Ouchterlony et al. (2009), Ittner et al. (2014), and Siren et al. (2015). Based on past literature the EDZ have in this paper been separated in the following subzones: 1. Failure Zone or over-break is the area outside the planned tunnel profile, including the Look-Out and hole deviation. This zone consists of fracture networks (both natural and blasting-induced), that caused rock fall-outs. The extent of the over-break can be determined by volumetric scanning and photogrammetry and the half cast factor can be used as a damage indicator. 2. The Damaged Zone is split into three parts and but the quantity and depth of damage is difficult to measure. Although it can be visualized by sawing of rock slices in the tunnel wall (Olsson et al. 2009), diamond coring (DC) or P-wave velocity reduction (Jern 2001): a. Inner Damage Zone (Crush Zone): It is located directly around the drill hole, and is caused by the shock-wave energy of the detonation. The micro fractures in the Crush Zone produce a white-wash (rock dust) in the half cast. b. Transition Zone: This zone consists of micro fractures that connect and form macro fractures, both radially and parallel to the tunnel wall. The macro fractures are caused by the gas expansion during the detonation of the explosive; it increases the pressure in the (micro) fractures and creates the macro fractures. Seismic reflection, rock slicing and core drilling can be used for the examination. c. Progressing Zone: In this zone the existing radial fractures propagate due to the increase gas pressure inside these macro fractures. Examination methods are seismic reflection, rock slicing and core drilling. In addition, the Peak Particle Velocity (vibrations) could be used to estimate the depth (Tesarik et al. 2011)."

Jan 1, 2016

By Robert M. Cox

Surface mining of coal in the South developed into a major industry during the 1960's. The economic significance of the industry is much greater than is readily apparent when one considers only the value of the coal mined. The abun-dant supply of relatively inexpensive steam coal for electric power generation that has been derived from the surface mines has provided the foundation for the industrial expansion that has occurred throughout the South. The region, in gen-eral, has enjoyed the benefits of plentiful low cost electric power. However, re-cent political decisions, at all levels of government, threaten to destroy or severely curtail the surface mining of coal and eliminate the economic advantages once enjoyed by the region. These political decisions are rapidly changing the basic rules of operation and fundamental economics of surface coal mining. Recent changes, resulting from the enactment of environmental and health and safety laws and various bureaucratic rules and regulations, have had a three-fold effect: 1) Greatly increased operating cost, 2) increased lead times for mine development, 3) limited potential reserve base for future mining. Also current legislative proposals are casting a shadow of uncertainty over the future of all coal mining operations that has created serious delays and in-creased cost for the expansion of the coal industry necessary to meet our project independence goals. Technology Surface mining is the safest and most economical way to produce raw materials from the earth's crust. It also affords a more healthier working environment for the individual miner. Surface coal mining now accounts for more than 60 percent of the annual coal production in the South. Surface mining of coal requires the removal of the overburden to expose the

Jan 1, 1977

By R. B. Taylor

The Esmeralda mine is located about three miles west of the town of Parral, in the State of Chihuahua, Northern Mexico, and about 400 miles south of El Paso, Texas. The area is serviced by the Interamerican Highway and a branch line of the National Railways of Mexico. The Parral district is quite typical of the semidesert of Northern Mexico, lying near the western margin of the Chihuahua basin and range province known in Mexico as the ?Mesa Central? In the immediate mine area, low rounded hills and rolling plans slope toward the Parral River. Surface elevation at the mine is 5,800 feet. The Esmeralda vein outcrops strongly, but was too low grade to be of interest to the Spaniards, The first claims were staked in 1897 and limited exploration work to a depth of 550 feet was carried out prior to 1912, at which time work was suspended. The Eagle-Picher Company acquired the property in 1944 and by surface diamond drilling outlined an orebody to a depth of 800 feet, Minas de Iguala, S. A, de C.V., one of Eagle-Picher?s totally owned subsidiary companies in Mexico, then unwatered the old workings, developed the mine, installed a modern differential flotation plant and started production lage in 1948. To the present, more than two and ahalf million tons of ore have been mined and milled producing lead and zinc concentrates.

Jan 1, 1958

By Elżbieta Węglińska, Andrzej Leśniak

The earthquake locations are generally scattered mainly due to a simplified velocity model or seismic event picking errors. The aim of our research was to increase the resolution of the cloud of microseismic events recorded during mining activity in the Bobrek hard coal mine on the 3/503 coalface to delineate seismically active structures using unsupervised machine learning algorithms. We presented results of applying two completely different algorithms for reducing scatter in microseismic location to all events recorded during mining activity on the coalface - the collapsing (proposed by Jones and Stewart in 1997) and condensation (proposed by Kamer in 2015). The collapsing method simplifies the seismic cloud by shifting events inside their error ellipsoids towards local source densities. The error ellipsoids are determined by errors in the measured parameters and seismic network configuration. The advantage of the collapsing method is the partial elimination of blurring of the microseismic cloud. The condensation method reduces the size of the set of seismic events without changing the geometrical information. The reduction of the number of seismic events in the catalog takes place through the condensation of localized events with larger uncertainty into events with lower uncertainty. The spatio-temporal analysis of microseismic events was performed separately on two processed clouds – collapsed and condensed one. We examined how collapsing and condensation methods affect the automatic detection of clusters of microseismicity using density-based spatial clustering of application with noise algorithms. We compared structures detected by the machine learning algorithms in both seismic clouds first created by collapsing and second by the condensation. We identified structures created by mining activity and structures related to the local tectonics activated by mining. The presented results are essential for the prediction of future tremors induced by the mining operation and tectonics and thus ensuring safety in the mine.

Apr 26, 2022

By Y. S. Roditis

Traditionally, open pit optimization has been used to produce a single outline which can guide the pit design. This paper describes how a series of optimum nested pits are utilized to: a. produce different mining sequences and to help in mine planning and phase design; b. evaluate different metallurgical processes, production scenarios and equipment size; c. investigate the sensitivity of a project to prices, recoveries, production rates, costs, ultimate pit slopes etc.

Jan 1, 1993

By C. C. Stewart

Jim Walter Resources, Inc. operates four underground coal mines in Alabama. In 1986, during longwall recovery operations, sparks from a torch ignited methane that migrated onto the face after a roof fall. The fire quickly spread to the gob at the tailgate end of the longwall. The fire was successfully "area" sealed and mining operations resumed after five weeks. However, several problems were encountered during this process. This paper describes the events following the fire, methods used to control the situation, problems encountered, and steps taken to ensure preparedness for any future occurrences of this type.

Jan 1, 1993

By J. L. Workman

The stability of spoil and highwall slopes are important to successful strip mining. This paper discusses soil parameters of importance in stability analysis. The common mechanisms of spoil failure are discussed. Modes of highwall failure are also outlined. The importance of water to stability is presented. Dragline mining methods most suited to creating spoil and highwall profiles that address stability needs are provided. It is concluded that groundwater and surface runoff must be well controlled, and that it will often be necessary to modify spoil and highwall configurations to achieve a stable overall slope angle.

Jan 1, 1996

By R. C. Gilmore, A. Juganda, Jr. Bogin, S. Saki, S. A. Lolon, J. F. Brune, Jr. Zipf, J. W. Grubb

"Methane-air mixtures form explosive gas zones (EGZs) in underground longwall coal mine gob ventilation systems. Such EGZs have caused a number of fatal mine explosions, including the 2010 disaster at the Upper Big Branch mine, where 29 miners lost their lives. Researchers at the Colorado School of Mines use Computational Fluid Dynamics (CFD) modeling to predict EGZ locations. In this paper, a model of a bleeder-ventilated gob system includes two adjacent panels, an active longwall and a mined-out gob. Boundary conditions for the simulations match statutory ventilation conditions for methane concentrations and air flow rates at common measurement points throughout the mine. The modeling results predict the persistence of EGZs in the gob that may compromise the effectiveness of the bleeder ventilation system. INTRODUCTION Mine operators must maintain statutory air flow and air quality requirements at various locations throughout the mine ventilation network. U.S. regulations generally require mine operators to establish bleeder ventilation systems surrounding longwall gob areas (30 CFR §75.334.) Gilmore et al. (2015) documented that explosive gas zones (EGZs) exist within bleeder-ventilated gobs and may extend into the bleeder entries that must be examined weekly, presenting an immediate fire and explosion hazard to mine examiners. In a project funded by the National Institute for Occupational Safety and Health (NIOSH) under contract 200-2009-31409, researchers at Colorado School of Mines have developed a tool for modeling gob air quality using Computational Fluid Dynamics (CFD). This CFD model is capable of examining a wide range of longwall mine ventilation systems. Marts et al. (2014a, 2015) studied progressively sealed gobs with U-type ventilation and using a back return. Saki et al. (2015) examined the impact of gob ventilation boreholes and face air quantity effects on tailgate methane concentrations. Gilmore et al. (2014) modeled bleeder-ventilated gobs and Gilmore et al. (2015) studied the effects of bleeder regulator settings on EGZ volume and locations in the gob. CFD studies for progressively sealed gobs were generally carried out using 5000 ft (1500 m) panels because the gob atmosphere remains largely unchanged from about 500 m (1,500 ft) inby the face. A modular meshing methodology (Gilmore, 2015) permitted researchers to extend bleeder models to 10,000 ft (3050 m) to include the full extent of bleeder entries. This paper further expands the bleeder CFD model to study the gob atmospheres of two adjacent longwall panels, each 10,200 ft (3100 m) in length, with the active face located 6,700 ft (2040 m) from the startup room."

Jan 1, 2016