Search Documents

By N. Careddu

In recent years, slabs with a rough surface have captured a large share of the ornamental stone market. However, the main technologies used for this type of treatment are based on mechanical shock (bush-hammering) or thermal treatment (flaming or flame-finishing). These traditional technologies are widely used, but have many limitations that decrease their usefulness. The purpose of this study was to develop a technology that enhances the natural colors of the rock and produces a rough surface without compromising its mechanical characteristics, in contrast to traditional technologies. This report shows the technical, economic and aesthetic results obtained with a new water-jet treatment and compares it with competing technologies.

Jul 1, 2010

By Kang-Hyun Lee, In-Mo Lee, Byung-Kyu Kim, Parkm Jinho, Seoung-Won Lee

"In this study, the TBM Resistivity Prediction (TRP) system is developed for predicting the location, thickness, permittivity ratio and electrical conductivity of anomalous zones ahead of tunnel face using the measured resistivity of the ground. The applicability of the developed system was verified by performing field tests at a construction site in which an EPB-shield TBM is used for tunnelling work. In the first field test, it was found that the rock around the tunnel face had the same resistivity and permittivity with the rock ahead of the tunnel face indicating no anomaly ahead of the tunnel face. In the second test, a stronger zone 5-m thick was predicted ahead of the tunnel face based on lower permittivity than that of the rock around the tunnel face. The ground condition assessed by the newly developed TRP system matched well with that either predicted from geophysical exploration or directly obtained from drilling boreholes or from daily observed muck conditions. INTRODUCTION During tunneling work, the emergence of unpredicted zones of relatively weaker or stronger ground can lead to delays in construction work or an increase of construction cost. Predicting anomalous zones ahead of tunnel face in advance can thus prevent time and economic loss. For these reasons, various methods to predict the ground condition ahead of the tunnel face have been studied and developed. Prediction methods using various kinds of equipment include tunnel seismic prediction, ground penetrating radar, electromagnetic surveys based on electronic antennas, and electrical resistivity surveys conducted by analyzing electric currents in the ground ahead of the tunnel face (Ryu et al. 2008). However, most of the prediction methods are only applicable to conventional tunneling job sites, which feature free access to the tunnel face. In mechanized tunneling projects, accessibility to the tunnel face is very limited because the tunnel face is occupied by the TBM."

Jan 1, 2016

By Ignazio Carbone

"During the design of a typical modern subway, engineering aspects prevail since underground structures remain hidden to most humans. Aligning the advanced architectural concepts with the engineering requirements of the Naples Metro Line 1 (Italy) called for a thorough rethinking of the design process so that the engineering could be kept aligned with the architecture, integrating seamlessly the two with the construction methods, standards and technology.The preliminary design process consisted of three major phases: •,geotechnical and geological issues, preselection of construction methods; •,functional scenario based on engineering and construction requirements; •,review and merging of the architectural concept with the functional and engineering aspects. The last phase proved the most demanding one, matching the first outline sketches with the applicable construction methods. This required continuous alignment of approaches, eventually leading to the design consistent with the original architectural vision, yet fully compliant with the engineering and construction framework. At the beginning general information on Line 1 will be provided, followed by some main features of the construction work along the Dante – Garibaldi section both for the tunnel and the stations. At the end, the selected methodology and the related consequences on the functional, technical and architectural design will be outlined.City of Naples current municipal transportation plan envisages a circle ring line for the metro line M1. Actually it’s open to public the segment Piscinola – Dante – Garibaldi run by AMM, municipal company. This ring segment has been built by Metropolitana di Napoli, while Napoli Metro Engineering (company belonging to MMspa Group) is in charge for the planning of entire system and construction management. Line 1 connects Piscinola-Secondigliano northern periphery to Vomero shopping neighborhood, downtown and Central Railway Station."

Jan 1, 2016

By T. Brozell

"Communities near sand mines and processing facilities in Wisconsin have raised concerns regarding possible exposure to ambient respirable (PM4) crystalline silica. Fenceline PM4 (particulate matter captured with a 50 percent cut size of 4 micrometers aerodynamic diameter) crystalline silica concentration data were compiled at Fairmount Santrol Inc., Mathy Construction Inc. and U.S. Silica facilities. The long-term average PM4 crystalline silica concentrations ranged from 0.05 to 0.45 micrograms/m3 when sample values below the limit of quantification were treated as zeros. All of the long-term average concentrations were less than 20 percent of the Minnesota Department of Health’s and California Office of Environmental Health Hazard Assessment’s PM4 crystalline silica chronic reference exposure level of 3.0 micrograms/m3. The measured concentrations were consistently within the local background concentration range.Air Control Techniques P.C. compiled the sampling data using Thermo Fisher Scientific Inc. Partisol 2000i PM2.5 samplers meeting the requirements of 40 CFR Part 50, Appendix L. These samplers were adapted to capture particulate matter with a 50 percent cut size of 4 micrometers. The use of polyvinyl chloride filters allowed for crystalline silica X-ray diffraction analysis by NIOSH Method 7500. The combined use of adjusted PM2.5 filter-based samplers with Method 7500 crystalline silica analyses provided for a highly sensitive limit of quantification of 0.31 micrograms/m3 of PM4 crystalline silica.BackgroundIn 2005, the California Office of Environmental Health Hazard Assessment (OEHHA, 2005) adopted a 70-year chronic reference exposure level (REL) for PM4 (particulate matter having aerodynamic diameter of 4 micrometers or less) crystalline silica. The REL was extrapolated from occupational hygiene epidemiological studies, essentially all of which were based on in-plant PM4 crystalline silica measurements. No well-established ambient sampling technique for PM4 crystalline silica was available at the time that OEHHA adopted its REL. The personal samplers used for the National Institute for Occupational Safety and Health (NIOSH) Method 0600 in-plant sampling of employee exposure were designed for concentrations higher than ambient levels. The limit of quantification (LOQ) of PM4 crystalline silica on NIOSH 0600 filters was too high for the effective sampling of ambient air."

Jan 1, 2015

By J. B. Malcolm

The discovery of tungsten-bearing quartz outcroppings in Vance County, N. C., by the Hamme brothers in 1942, made international news in the mining industry and was, in fact, one of the major ore discoveries made in the U.S. during the last 25 years. Operations began at the Hamme mine in 1942, but after 16 years of successful operation, the mine was closed down in 1958 under adverse market conditions. By that time, it had produced nearly 20 million lbs of metallic tungsten. Because of the square-set timber mining method then in use, mine operating expenses were high, actually representing 78% of the total operating expenses at the property. In timber work alone, 160 men were employed. Approximately 500,000 bd ft of timber were placed monthly at a direct supply cost of $1.00 per ton of ore mined. Late in 1959, following a slightly improved position in the tungsten market, company management decided that, by changing the mining method, the operation could be economically feasible. The major premise in this decision was that a reduction of from 25 to 30% of the mining costs could be achieved by the conversion of the mining method from square-sets to horizontal cut and fill. Reopening of the mine began in February 1960, Full production has now been reached and overall mine productivity has been doubled.

Jan 1, 1962

By J. Hupka

The limited effectiveness of the original hot water process for recovery of bitumen from certain Utah tar sands containing bitumen of higher viscosity (e.g. Sunnyside, Tar Sand Triangle)1,2 indicated that bitumen viscosity strongly' influences the separation efficiency. In this regard, there should exist a critical value of bitumen viscosity above which the effectiveness of the hot water process decreases significantly. Apparently certain tar sands contain bitumen of such high viscosity that even a digestion temperature of nearly 100°C is insufficient to lower the viscosity below the critical value. In addition it seems that differences in physico-chemical forces which act between sand and bitumen are negligible in comparison to the difference in visco-mechanical forces. Predominantly mechanical forces hold viscous bitumen on the rough surface and in the pores of sand particles, resulting in strong adhesion. This phenomenon is a critical feature in the phase disengagment of oil-wetted domestic tar sands with viscosity control by temperature. Besides increasing the temperature for viscosity control the effectiveness of the original hot water process could be enhanced by control of bitumen viscosity with diluent additions. Strictly speaking this appraoch is the only possibility for heavy bitumen for which the high temperature of digestion does not lower the viscosity sufficiently. As a result of viscosity control by diluent addition the digestion temperature can be lowered which is important from an industrial standpoint. Another important consideration is that effective phase disengagement occurs only when the entire bitumen phase has the same viscosity. This means that some time (penetration time) is necessary for complete and uniform dilution of the bitumen. If the viscosity of bitumen, which is a function of temperature, diluent addition and penetration time, controls the separation efficiency, hot water processing of many different kinds of tar sands should be possible, assuming that the sand phase consists primarily of quartz-type minerals.

Jan 1, 1982

By W. E. Benton

Diatomite or diatomaceous earth is a siliceous sedimentary rock principally made up of the skeletal remains of the diatom, a microscopic, single-cell aquatic plant related to algae. The unique structure, chemical stability and physical properties are the major attributes of diatomite not met by other forms of silica. The production of diatomite was down in 1982 vs. 1981, reflecting the worldwide recession. The principal markets for diatomite products continue to be basically filtration and fillers. The outlook is for small but steady growth into the 1990s.

Jan 1, 1983

By R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (K088) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron-and steel making and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By Lennart Bergstedt

Boliden Aktiebolag, the prime base metal mining company of Sweden, annually treats some 11-12 million tons of sulphide ore in nine concentrators. Its first flotation plant was established in the early thirties for the complex Boliden ore. Since then, the number of mines and plants has gradually increased. Considerable effort has been devoted to the development of all phases of the technology of ore prospecting, mining, milling, smelting and refining. This has been necessary due to the complex and low-grade ores. The development of concentration has mainly been directed toward the arts of grinding and flotation. During the forties and fifties, open-stage fine crushing followed by two-stage grinding in rod and ball mills with cyclone classification was successfully introduced and used throughout the plants. The increasing cost of grinding media led to studies of an autogenous grinding technique as early as 1945. Basic test work commenced during the early fifties, with a. number of ores tested for pebble grinding. In 1956 a new pilot plant was built, with equipment installed for the continuous testing of pebble grinding and, later, for primary autogenous grinding of run-of-mine ore. The intensive test work showed that pebble grinding was feasible in almost all of the plants. At this early stage of testing, however, the merits of autogenous grinding could not be fully evaluated. As a. consequence the rod mill/ball mill grinding systems were converted to rod mill/pebble mill systems whereever possible. In parallel with the converting of grinding systems the development work concerning the merits of autogenous grinding went on. The major result

Jan 1, 1977

By C. C. Hatch

As part of a general project to simulate a concentrator, the Brenda Mines Limited secondary crushing plant, located near Peachland, B. C., was sampled during the summer and winter of 1975 to develop a digital crushing plant simulator specific to the Brenda operation. The purpose of this simulator was to study the influence of manipulable process variables on important responses and to permit study of alternative circuit configurations if desired. This paper describes the simulation methodology employed and presents the results of a computer study of the secondary crushing plant (1).

Jan 1, 1979

By J. Richard Tonry

In portland cement manufacturing, the raw materials axe changed to clinker in the burning operation. Generally the rotary kiln is used for this purpose and involves many processes, including pelletizing and nodelizing. This transformation is called clinkering, and is analyzed as now generally practiced in cement making, from the raw material to the resulting clinker.

Jan 1, 1963

By Marie-Josée Banwell, Cyriac Sebastian, Giacomo Falorni, Sara Del Conte

Interferometric Synthetic Aperture Radar (InSAR) is a satellite-based monitoring technique that complements other in-situ methods for detecting and measuring surface displacement. Recent advances in data processing algorithms, coupled with the use of high-resolution satellite systems, make it possible to now provide high-frequency InSAR monitoring services, with updated results delivered every time a new satellite image is acquired. The advent of large, continuously updated data sets, however, brings new challenges, including the need to rapidly sift through the data to identify only those points showing relevant ground displacement information. This has been achieved by using trend variation analysis tools, that quickly isolate and highlight only areas of anomalous behavior. The paper focuses on project case studies where continuous InSAR monitoring has proven to be key in identifying displacement trend changes near tunnel alignments.

Jun 13, 2021

By D. R. Spears

The U.S. Bureau of Mines has had an ongoing interest in developing new reagent schemes for floating Stillwater, MT, chromite ore. Previous reagent schemes have been unsuccessful in achieving complete separation, primarily because little is known about the surface chemistry of the minerals in this ore. In order to design a rational reagent scheme, a study of the binding of various functional groups (R = -H, -OH, -CO2H, -NH2) on the two components (chromite and forsterite) of the Stillwater chromite was undertaken. Electron Paramagnetic Resonance (EPR) Spectroscopy was used to determine the adsorption isotherm, from a cyclohexane solution, of spin-probes which contained the functional group of interest. This was complemented by studies of the saturation surface coverage of the spin probe on the two minerals. In each case, more sites existed on chromite than forsterite; however, the forsterite sites were more strongly binding for each functional group. The results are discussed in terms of their implications for flotation.

Jan 1, 1994

By I. G. Bowen

The pumping of abrasive and sometimes corrosive slurries is normally carried out at modest heads (say 100 ft) with specially designed centrifugal pumps. When heads become higher than this, two or more pumps are used in series but ultimately the system requires staffed pumps with consequent increase of costs. The only other type of pump suitable for high heads is the Ram pump but this is notoriously subject to wear. The paper describes a novel application of the so-called "lock hopper" principle to continuous pumping of slurries. The pump itself is never in contact with the abrasive slurry nor is it subject to head or capacity limitation. It works by displacing slurry with the clear fluid component of the slurry (in most cases water) through cylindrical vessels fitted with plug valves to control the discharge and filling operations. Two such vessels are used and the scheme is completed with a liquid clarifier which allows the pipe flow to be maintained continuously. The paper describes experience on the prototype unit used to discharge tailings from a coal washery in Scotland. A tentative evaluation is also made of the economics of this pump against conventional equipment.

Jan 1, 1965

By John Batchelder

The Copper Canyon Cu-Au-Ag deposits include two geologically distinct hypogene ore bodies developed primarily in late Paleozoic rocks adjacent to a 38-m.y.-old potassic-altered granodiorite, whose emplacement seems to have been controlled largely by the Virgin fault, a north-striking normal fault. Widespread but subeconomic concentrations of sulfides as fracture and cavity fillings in skarn apparently preceded the final intrusion of the granodiorite. In the west ore body, metals reached ore-grade concentrations through the massive replacement of andradite by chalcopyrite, pyrrhotite, and pyrite mineral assemblages. The east ore body probably formed after the granodiorite reached its present level. Calculated 6dD values of water in equilibrium with primary and secondary biotites range from -76 to -99 per mil at temperatures indicated by d180 values from coexisting quartz and biotite. The lightest values are in secondary biotite from the east ore body. These data suggest that fluids associated with potassic alteration here were most likely composed of magmatic water mixed with some meteoric water.

Jan 1, 1976

By Michael M. Kimberley

Stratiform uranium deposits occur in Canada along the north shore of Lake Huron near the base of the Middle Precambrian Huronian Supergroup. Outcrop of the Buronian Supergroup extends for over 400 km from Sault Ste. Marie in the west eastward through Sudbury and then northeastward to Cobalt. Maximum stratigraphic thickness exceeds 5 km. The predominant Huronian rock type is metamorphosed sandstone (quartzite), with sub- ordinate argillite, conglomerate, mixtite (possibly tillite), volcanic rocks, and minor limestone, Much of the quartzite is highly feldspathic. Substantial uranium ore was first discovered in Huronian rocks in 1953 and has been exploited continuously since the initial mine-mill plant was constructed at the Pronto ore body, 30 km south of the present townsite of Elliot Lake. Only one ore body remains in production, however. It is shared by Rio Algom and Denison Mines 14 km north of the town of Elliot Lake.

Jan 1, 1980

The future phosphate rock deposits in South Florida contain a significant fraction of dolomite. The high MgO content of the rock is undesirable in the production of phosphoric acid. Several flotation schemes have been attempted to separate dolomite from phosphate rock. Alternately, Selective Flocculation process has been suggested to separate dolomite from apatite. A high MgO content rock was simulated by a 30:10:60 synthetic mixture of apatite, dolomite and silica. Single mineral selectivity was observed in the mixed mineral systems apatite-silica and dolomite-silica with Polyacrylic acid (PM) and Poly(ethylene oxide) (PEO) flocculants respectively but not realized in apatite-dolomite system with PEO flocculant. Heteroflocculation, suspected to be the major reason for loss in selectivity, was minimized by addition of a Site Blocking Agent (lower molecular weight fraction of PEO). Process parameters such as size reduction schemes, flocculant/SBA dosage, and pH were investigated to achieve the desired separation. The selectivity obtained in binary mixed mineral tests was translated into the ternary mixed mineral system, viz. apatite-dolomite-silica. In this presentation surface chemical characterization of the samples and their flocculation behavior will be discussed.

Jan 1, 1994

By M. S. Celik

Adsorption of sodium dodecylsulfonate (SDS) and dodecylaminium hydrochloride (DAH) on Buller seam coal, New Zealand, have been studied. Both surfactants adsorb effectively on the coal below pH 8, and the adsorption isotherms established at pH 4 are essentially the same at lower concentrations. These findings suggest that the adsorption of these two ionic surfactants on coal is controlled by a hydrophobic bonding mechanism. However, the results of calorimetric studies suggest that coulombic attraction also plays a part in the adsorption mechanisms. It has also been found that both the SDS and DAH adsorbed in the first monolayer are not removed by lowering the surfactant concentrations in the bulk solution.

Jan 1, 1993

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"Duluth & Iron Range Railroad. The Duluth & Iron Range Railroad was built from Two Harbors to the Vermilion range at Tower, a distance of 67.6 miles, in 1884, and extended to Ely, twenty-one miles east of Tower, in 1888. It was built into Duluth in 1886, and branches were extended from its main line to the Mesabi mines in 1892 and 1893. The original grades on this road are very steep, going north, and in the thirteen miles from Two Harbors to Highland there is a rise of 1,150 feet. A new line between these points has been built with an increase of three miles in distance and with maximum grades of 1 per cent. Duluth, Missabe & Northern Railway. The Duluth, Mis¬sabe & Northern Railway was constructed from Stony Brook to Mountain Iron, a distance of 48.62 miles, in 1892. The Biwabik branch from Iron Junction to Biwabik, a distance of 15.54 miles, was constructed in 1892. The Superior branch from Wolf to Hibbing, a distance of 16.06 miles, was co11structed in 1893. The Alborn branch from Coleraine Junction to Coleraine, a distance of 53 miles, was constructed in 1906. The total main line mileage is 242 miles, of which 82 miles from Duluth to Hibbing is double tracked"

Jan 1, 1920

By W. C. Hellyer

The Granduc ore body is located beneath glacial terrain on the borders of British Columbia and Alaska, some 600 miles from Vancouver and 30 miles from Tidewater at Stewart, B. C. The concentrator and attendant facilities are located in wilderness country at an elevation of 2500 feet. The average annual snowfall is 65 feet. Surface facilities and ore body are linked by a 10 mile railroad haulage tunnel. This copper property has been developed by Granduc Operating Company on behalf of Newmont Mining Corporation and American Smelting and Refining Co. First production started in November, 1970. In August, 1966, Granduc Operating Company awarded an engineering and construction management contract to McKee-Swan Wooster, a joint venture of A. G. McKee of Canada and Swan Wooster Engineering Company Limited, to design a concentrator to treat approximately 7000 tons of ore per day. The isolated location of the Granduc ore body indicated comparatively high freight rates on consumable items of concentrator supplies such as reagents, grinding media, etc. A firm flowsheet for the flotation of the Granduc ores having been developed by the Danbury laboratory of Newmont Exploration Limited, attention was devoted to means of reducing operating costs. One obvious method was to reduce or eliminate the costs of steel grinding media by employing some form of autogenous grinding. two pilot plant operations were carried out at the facilities of Lakefield Research of Canada Limited, in which autogenous grinding of Granduc ores was investigated. The results of these investigations led to the selection

Jan 1, 1972