Search Documents

By A. Haghighat

A risk analysis on mine fires for all U.S. underground coal mines from 2000–2012 was completed to identify locations that have a high risk for fire incidents. The data for this analysis was extracted from the Mine Safety and Health Administration’s (MSHA) mine fire accident reports database. After identifying fire incidents from this database, a risk matrix was developed for underground locations that showed a significant propensity for fire incidents. This matrix associates the hazards and risks with the severity and frequency of their consequences at each location. These significant mine areas will be the concentration of future studies in fire behavior, suppression techniques, and simulation methodologies. INTRODUCTION Fires in underground mines pose significant hazards to personnel because of inherent restrictions to movement and limitations to egress routes. Despite improvements, mine fires remain serious hazards in underground coal mine. In order to better mitigate the risks from fire hazards in the modern underground mining environment, a better understanding of where fire events occur must be gained. The following paper presents an investigation on the number of fatal and non-fatal incidents in underground coal mines fires from 2000 to 2012. Three phases of risk assessment (i.e., risk identification, estimation, and evaluation) were applied to the recorded fire events from the MSHA incident database that occurred during this time period. Using this process, a fire hazard was first defined. This definition was then used to identify any incidents that had occurred as a result of the defined hazards. The seriousness of the injuries and damages were finally quantified for each incident though an estimate of severity and frequency and then aggregated according to underground location (ISO, 1999; Van Duijne, 2008). Using this approach, locations prone to incidents resulting from fire hazards were first identified. The risk for the occurrence a fire incident in general was then estimated for each of the identified locations. The results of this assessment will be used to improve fire simulation techniques for the identified, high risk underground locations. RISK IDENTIFICATION A risk for this assessment was defined as any single occurrence of a fire initiated by the ignition of gas, dust, or electricity. Each recorded occurrence of such an event in the MSHA incident database was counted as a single fire incident. Both non-fatal incidents that were reportable but did not result in a fatality and fatal incidents that fell into the aforementioned criteria were counted. Incidents in the MSHA database that were already classified as “generic” were not considered. The remaining incidents were then totaled and aggregated according to the underground location in which they occurred. In previous studies, a number of locations, which are listed in Table 1, were highlighted as high fire hazard areas (McDonald et al, 1980; Pomroy et al, 1995; De Rosa, 2004). These locations were used to group the fire incidents extracted from the MSHA incident database. The compiled numbers of non-fatal and fatal underground coal fire incidents from 2000 to 2012 are displayed in Table 1.

Jan 1, 2019

By MAURICE SUNKPAL, Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

In this study, various rib bolting scenarios were investigated to better understand the effectiveness of the support systems. A coal mass constitutive model is implemented to a distinct element method (DEM) code, and rib factor-of-safety (RibFOS) analyses were performed by applying strength reduction for the coal matrix and explicitly modeled face cleats. Ribs with various overburden depths and mining heights composed of solid banded bright coal were considered. Different scenarios such as rib bolt length and number of bolts were studied to quantify the effect of primary rib support density on rib stability. As a result of the unsupported coal rib analyses, a decaying exponential relationship is proposed between the mining height-overburden depth and the RibFOS. The developed coal rib models clearly show the coal-rib bolt interaction and illustrate how the addition of rib bolts restricts the movement of the coal rib. The results reveal that the strength-reduction method in DEM code with the coal-mass model can aid in the development of practical primary sup- port charts, which can help in the rib support design process.

Feb 1, 2024

By K. Lapakko

Kinetic tests results are influenced by methodological variables, including test duration and mine waste particle size. Some samples tested produced neutral drainage in kinetic tests for more than two years prior to drainage acidification. The potential for long "lag times" can be assessed based on the mine waste mineralogy. The lag time duration can be estimated using this mineralogy in conjunction with dissolution rates observed in the kinetic tests. The influence of particle size on the drainage quality is dependent on the variation of the availability of acid-producing and acid-neutralizing minerals with particle size.

Jan 1, 1998

By Rob Herr, Irwan Halim, Heather Marsh

This project will expand sanitary sewer within the City of Columbus. It consists of 2.5 mile long, 72-inch finished diameter pipe grouted inside 10.8-foot diameter tunnel excavation in shale. This paper describes the multi-faceted geotechnical exploration to minimize the underground risks. The tunnel will cross below a buried valley with minimum cover of highly weathered rock. The risk mitigation to cross the valley includes contingencies and cost allowances. Provisions to prevent impact on adjacent groundwater resources will be described. Latest construction updates will be provided including contractor alternate shaft support and pre-excavation probing to mitigate tunneling risk below the valley.

Jun 23, 2024

By T. Luterbach, V. T. McLemore

"Trace element analysis of placer gold can be used as a valuable exploration tool in order to determine the original deposit source and locating lode gold deposits. Placer gold collected from multiple districts in New Mexico and Alaska, coupled with a broad database of previously analyzed placer gold samples indicate correlations between chemical signatures (especially gold, silver, and copper) and type of deposits (i.e., Au-rich copper porphyry deposits, Au porphyry deposits, and epithermal deposits). By completing a chemical analysis and determining the particle morphology of placer gold collected from these districts using an electron microprobe, patterns in the chemical signatures from each location can be used to examine chemical variability (1) within the individual placer gold particles, (2) within the same district and (3) among different districts. INTRODUCTION Although there are numerous past studies on the chemical composition of placer gold by Newberry et al. (1997), Melchiorre (2001, 2009), Townley et al. (2003), and McLemore et al. (2014), the gold analyzed tends to be collected from one or few specific districts. Rarely do those studies compare compositional results to additional districts, or elaborate on the correlation between the elemental composition of the placer gold and the original deposit source for the respective districts. This research analyzes the composition of placer gold from multiple districts and within the same district. There are a number of elements, which can, in various quantities, be present in placer gold particles. Native gold can be in complete solid solution with native silver and contain additional elements including Cu, As, Pb, Fe, and S. The chemical signature of the gold is determined by the thermodynamic conditions of precipitation and transport as well as the total metal content of the system. As Townley et al. (2003) explains, “These thermodynamic conditions and metal budget differ from one type of hydrothermal deposit to another, and hence different deposit types will each have a characteristic gold compositional signature.” Identifying this signature can be a highly valuable tool in exploring for gold, as it can not only be used to determine the original source deposit of the placer gold, but provide valuable insight as to the erosion level of the present deposit."

Jan 1, 2016

By Xiyu Gao, Yi Yang, Mark I. Pownceby, Shuiping Zhong, Miao Chen

In the present study, X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray absorption near edge structure (XANES) spectroscopy, and Raman spectroscopy were used to investigate the effect of chloride ions on chalcopyrite bioleaching and chemical leaching at 25 °C. The leaching results show that the addition of chloride ions suppressed the dissolution of chalcopyrite in both chemical and bacterial leaching. In chemical leaching, the solution redox potential in the experiment without Cl− stayed in a range more suitable for chalcopyrite dissolution compared with experiments with Cl− . In bioleaching, the bacteria activity was suppressed by Cl− leading to low dissolution rates of Cu. Surface morphology and chemical speciation studies confirmed the formation of potassium jarosite on the surface of the chalcopyrite leach residues. In addition, S K-edge XANES indicated the formation of trace amount of elemental sulfur and covellite on the mineral surfaces.

By E. H. Christiansen

The most valuable gem- quality red beryl comes from the Wah Wah Mountains of south-western Utah (Fig. 1). Red beryl occurs as a secondary mineral in topaz rhyolite. Marketable crystals from the Wah Wah Mountains have been produced from the Violet Mine, operated on a limited scale since 1976 under the ownership of the Harris family of Delta, UT. From 1989 to 1995, production from the mine amounted to more than $3 million with an inventory of several million dollars of unsold gems (Harris, 1995). In 1994, Kennecott Exploration leased the mine and surrounding claims to determine reserves and feasibility of gem recovery. Mining and exploration activity are continuing. Previous work on red beryl has dealt mainly with crystallographic, chemical and optical properties of the crystals (Shigley and Foord, 1984) with only general descriptions of the geology (Ream, 1979). However, the conditions needed for formation of red beryl have not been well constrained. It is generally proposed that beryl originates by precipitation in fractures and vugs from high-temperature gases as they are released from slowly cooled rhyolite lava. Dozens of topaz rhyolite flows and domes, similar in composition to the beryl-bearing flow in the Wah Wah Mountains, occur across the western United States (Christiansen et al., 1986). All of these flows devitrified to form vapor-phase topaz and locally other vapor-phase minerals such as bixbyite, garnet, hematite, pseudo-broo- kite and fluorite. But the occurrence of beryl is rare. Even within the rhyolite flow that hosts the red beryl, the productive open pits comprise only a small fraction of the surface area of the flow. Apparently, the conditions that favor the formation of red beryl are rarely achieved. Geologic setting The rhyolite flow that hosts the red beryl deposit lies along the eastern flank of the Wah Wah Mountains (Fig. 1). Prevolcanic rocks consist of Proterozoic, Paleozoic and Mesozoic sedimentary rocks that were folded and thrust to the east during the Sevier orogeny. Cenozoic volcanism began about 34 Ma. It consisted mostly of large volume dacitic ash flows and lesser volumes of low- silica rhyolite and andesitic lava flows. Beginning about 23 Ma, the style and composition of volcanism changed to smaller-volume, ash-flow and dome-forming eruptions of high-silica rhyolite and trachyandesitic lava. These rocks form the Blawn Formation of which the beryl-bearing rhyolite is one member (Best et al., 1987). Abbott et al. (1983) reported a K-Ar age of 22.1 + 0.8 Ma for this flow. It is probably the oldest topaz rhyolite flow in the Wah Wah Mountains. A subsequent episode (12 to 13 Ma) of bimodal magmatism produced the Steamboat Mountain Formation. The rhyolitic part of that is locally topaz-bearing. Displacement on the late Cenozoic extensional faults that formed the north-trending mountain ranges began about 22 Ma. Geology of the Violet Mine The rhyolite that hosts the red beryl deposit is part of a flowldome complex that overlies nonwelded tuff of cogenetic origin. This rhyolite is exposed over an area of about 9 km2 (3.5 sq miles) (Fig. 1). An unknown additional portion of the rhyolite is concealed beneath younger mafic lavas and sediments.

Jan 1, 1997

By Anna Eleria, Joseph Welna, Jim Herber, Nathan Campeau

Constructed by stonemasons over 120 years ago, a portion of the Trout Brook Storm Sewer Interceptor (TBI) owned and operated by the Capitol Region Watershed District in Saint Paul, Minnesota, needed rehabilitation. A routine inspection of the 10-foot limestone block tunnel revealed degraded and missing mortar between the blocks, allowing significant infiltration and soil migration through the tunnel joints. Conditions, including damaged and missing blocks, were considerably worse in a 250-foot-long segment beneath a busy mainline railroad corridor. Barr’s solution included tuck-pointing to repair the mortar joints, shotcrete overlay, and construction of a hybrid cast-in-place/shotcrete “tunnel within a tunnel” to support the mainline railroad loads.

Jun 13, 2021

By Y. Guan

The dissolution behavior of silver in ammoniacal solutions with cupric ammine as an oxidant has been investigated using a rotating disc electrode. The rates of dissolution of silver were determined by an electrochemical means as well as a direct measurement of silver ions reported in the bulk solution as a function of time. The variables investigated included stirring speed, temperature, concentration of lixiviants, and pH of the solutions. The rate of dissolution under the conditions studied' was found to be controlled by an electrochemical reaction at the liquid/ solid interface with an apparent activation energy of 48.07 kJ /mole. The rate was found to be a half order with respect to the, concentration of cupric tetra-ammine, Cu(NH3)l+.; The results were explained in terms of a mixed' potential theory.

Jan 1, 1994

By Harold L. Lovell

The areas of application, the limitations imposed by water chemistry as well as the advantages and disadvantages in the use of limestone for the treatment of coal mine drainage have recently been described by the authors (1),(2), (3). The process has been demonstrated in continuous, full-scale operation to yield a treated water meeting specifications established by the Pennsylvania Sanitary Water Board and containing excess alkalinity. Their final pH levels are usually less than seven, a condition which avoids consumption of excess neutralization reagents, but which occurs with lime-based processes and results from unwanted side reactions. Operating experience has been cited by Calhoun (4) using ferric waters while others (5), (6), (7), (8), (11), have reported on related research efforts. Despite the advantages including ?the relative simplicity, and minimal costs of the process, there have been very limited industrial applications of mine drainage neutralization with limestone. Although any treatment of these waters may be considered as a temporary control measure (9), the lack of feasible, immediate alternatives, the extensive magnitude. of the waters and the high cost of treatment requires that optimum processes should be utilized and that operating experience in their use be developed as is feasible. This paper will review treatment experience with a ferrous water of moderate pollution loading .

Jan 1, 1972

By Wen L. Chen

The steam coal quality is less stringent than metallurgical coal quality. The steam coal is prepared either by cleaning full size range of raw coal or cleaning coarse coal only, leaving the fine coal raw. The latter scheme is more cost competitive. It is particularly applicable to U.S. eastern soft coal where low ash coal is concentrated in fine sizes. For raw coal size separation, a recently developed Rotating Probability Screen, developed by the British Coal Board, may be advantageously used for easy change of raw coal separating size and to avoid screen deck plugging when handling wet and clayey raw coals.

Jan 1, 1983

By J. D. Grenia

The Buick Mine is a joint venture of American Metals Climax, Inc., and Homestake Mining Company located 120 miles by road southwest of St. Louis, near the village of Boss, in the 'New Missouri Lead Belt' (See Figure 1). Since start-up in 1969, over four million tons of lead-zinc ore have been mined and milled at Buick. Situated about 1,100 feet below the surface at an elevation 270 feet above sea level, the flat lying sinuous ore bodies are up to 250 feet wide, 85 feet high and several thousand feet long. Mineralization is galena, sphalerite and chalcopyrite in dolomite, Access to the mine is through two 18'Ø concrete lined vertical shafts - one for servicing and the other for hoisting ore (See Figure 2). The mine is being worked by a modified room and pillar method using both rubber tired equipment and a sub-level rail haulage. Ore is broken from first pass headings, back and bench faces and transported by load-haul-dump units to ore passes located on 900 foot centers. The ore is pulled from chutes on the sublevel 90 feet below into 15 ton bottom dump cars and delivered in 10 car lots by a 15 ton diesel locomotive to a 42" gyratory crusher (See Figure 3). A recent innovation has been the introduction of two 50 ton trucks with plans to haul up to 60% of the ore on the mining level to an ore pass feeding directly to the primary crusher (See Figure 4). Ventilation raises up to 16'Ø, which were originally planned for 900 foot centers, are now driven on 450 foot centers.

Jan 1, 1973

By John Dodd

Corrosion studies in laboratory ball mills and grinding environment simulations produce corrosion rates and total metal removal rates much lower than those recorded in operating production ball mills. The corrosion component of ball metal loss in commercial mills represents less than 10% of the total loss expressed as micrometers/hour of exposure in recent USBM tests. Such small absolute losses are consistent with ball metal loss measured in production ball mill marked ball wear tests to determine effects of corrosion and abrasion resisting properties of alloys in operating mills which indicate that metal hardness and microstructure determine relative metal loss rates of a given situation. The combination of ore characteristics and grinding process dynamics determine metal loss severity. Alloying for corrosion resistance and modification of the milling corrosion environment yield relatively small metal loss reductions. Alloying and heat treatment to produce high hardness and microstructures of high carbon martensite and for cast irons, M7C3 carbides produces the lowest metal losses in typical wet grinding applications.

Jan 1, 1984

By M. R. Yalamanchili

Recently, noequilbrium electrokinetic measurements using laser-Doppler electrophoresis were reported by Miller et al. (1992) for alkali halides and the sign of their surface charge thus determined. These results are generally as expected from simplified lattice ion hydration theory with KCI, under normal circumstances, being the most significant exception. In this regard, lattice defects (F centers and oxygen imperfections) have been found to influence the surface charge of KCI and its electrophoretic mobility. In particular, the presence of oxygen defect states in the crystal lattice has been found to be responsible for KCI's unexpected behavior. The concentration of oxygen defect states in KCI, as characterized by UV/Vis absorption, was varied in order to study their influence on the electrokinetic behavior and subsequently on the flotation response of KCl. At low oxygen contents « 60 ppm) KCI is positively charged as expected from lattice ion hydration theory. However, typically, KCI contains substantial oxygen (>300 ppm) sufficient to impart a negative surface charge which accounts for the selective flotation of KCI from NaCl by hetero-coagulation with oppositely charged alkyl amine hydrochloride collector colloids.

Jan 1, 1994

By L. E. Garner

Aggregate resources should be considered primary factors in urban development. Resource planning is essential because land values, previous construction, or zoning restrictions often preempt exploitation of aggregate deposits within an urban area. Sequential land use practices allow development of areas prior to urban development. Population and aggregate consumption trends in Austin, Texas, indicate that substantial quantities of reserves will be lost to future development. Aggregate materials are present in nearby seas. However, a comparison of transportation and reclamation costs indicates that reclaiming land after mineral extraction can be significantly cheaper than transporting materials longer distances.

Jan 1, 1979

By A. Habibi

The FMC Westvaco Trona Mine is located near Green River, Wyoming and has an annual production of 4.5M tons. Trona is an evaporite mineral that is processed into several products, mostly soda ash. The underground mine has two active development panels and one longwall (LW) panel. The mining horizon is about 500m below surface and the surrounding strata liberates methane. Three surface-based, blowing fans provide ventilation air as a positive pressure system. The mine operates a 225m long LW face, built by Joy Mining Machinery. Headgate and Tailgate developments are driven with four entries. The recovery room, at the end of each panel, is 8m wide with three access chutes. Additional recovery room support comes for concrete blocks used with a center to center spacing of 1.5m. As the LW enters this pre-driven recovery room there are notable responses and shifting ground stresses. This study was undertaken to measure the ground response using seven vibrating wire displacement transducers. These devices were used to monitor the convergence as the LW approached the recovery room. The methane concentration in the air ventilating the recovery room was also monitored. The correlation between convergence and gas liberation was then studied. The results show that the convergence varies from 0.1m to 0.25m along the length of the recovery room. Ventilating the recovery room becomes critical as methane is liberated from oil shale as the more plastic floor material is disrupted. Appropriate methods are employed to ventilate the recovery room.

Feb 23, 2014

"A carefully planned laboratory test program is the foundation for the successful development of a sulfide flotation process. In this paper, the development of a copper-molybdenum flotation process is described. However, the concepts discussed can be applied to most sulfide flotation systems and to many industrial minerals projects as well. Each step is examined, beginning with sample procurement and covering sample preparation, flotation test preparation grinding, scoping flotation tests for reagent scheme selection, rougher flotation parameter evaluation and cleaner circuit evaluation, through to locked-cycle testing and pilot plant design and operation. Ore variability and modeling to determine the response of various ore types to the optimum conditions established is also examined.IntroductionA carefully planned laboratory test program is essential for the successful development of any sulfide flotation process. These programs usually begin with a series of batch tests on several ore type composites to evaluate appropriate reagent schemes and delineate optimum rougher flotation conditions, such as primary grind size, flotation pulp density, flotation pulp pH and retention time. Cleaner parameters such as regrind size requirements, cleaner pH, pulp density and number of stages are then defined. Semicontinuous locked-cycle tests are performed using the parameters established in the batch tests to determine the effect of middling streams recirculation on flotation performance. The data generated and the experience gained in the locked-cycle tests may be used to design and operate a continuous pilot plant if relatively large amounts of concentrate are required for further process development, such as optimization of byproduct molybdenum production from bulk copper-molybdenum concentrate.A comprehensive ore variability program is undertaken to determine the response of various ore types to the optimum conditions established. These ore variability programs often test hundreds of samples in standardized batch rougher and cleaner tests to ensure that the orebody is well understood.This article describes the development of a copper-molybdenum flotation process, but the concepts discussed can be applied to most sulfide flotation systems and many industrial minerals projects. The block flow diagram in Fig. 1 provides an overview of the development process."

Jan 1, 2016

By S. Dawson

The Republic of South Africa has become a major producer of opencast coal in recent years. Opencast production commenced in 1970 and by 1977 some 10 million run of mine tonnes were being produced annually, Since then surface mine activity has increased to more than 60 million tonnes which represents approximately one third of the total annual South African? coal production. Whilst a substantial portion of this production is exported, the majority is used in the domestic market, The largest consumer, being the South?\ African Electricity Commission (Eskom), produces most of South Africa's electricity using coal fired power stations,

Jan 1, 1990

Little knowledge is available that considers the effects of continuous miner position on the possible respirable dust exposure of the remote mining machine operator. Such information could be very useful for increasing the awareness of the remote operator as to those parts of an extended cut that generate higher levels of respirable dust. This data could be used to develop guidelines for positioning the remote operator to reduce his potential exposure. This work details the effects of continuous miner position on dust levels measured on the machine and at the remote continuous miner operator location.

Jan 1, 1998

By L. P. Meade

The need to feed an established talc mill from a crude are source located closer to the mill prompted the drilling in 1986 of a previously mapped talc-carbonate deposit. This talc-bearing rock had never been considered as a potential source of crude talc are because of the high carbonate content and other deleterious minerals that were observed in outcrops. Selective mining, in-pit grade control and creative processing has allowed this deposit to be developed into an orebody. By definition, an orebody has to be a source of positive cash flow. With industrial minerals, this is determined as much by market acceptance as by are tenor.

Jan 1, 1992