Search Documents

By J. Kretschmann, K. van de Loo, J. Brune

In 2018, the German Federal government decided to phase-out the energy production using coal-fired power plants and to terminate lignite mining completely by 2038 at the latest. This decision will impact approximately 60,000 jobs. It will have an enormous impact on the socioeconomic development especially in all German lignite mining regions. To avoid economic and political friction, it is of utmost importance to achieve a sustainable transition towards a post-mining era and to offer residents in the mining districts perspectives for a good future that include adequate job opportunities. In this context, the German government is providing massive structural aids early on. As previous closure experiences from the German hard coal mining industry have shown, it takes at least a generation to overcome the effects of a strategic closing decision of this magnitude. Therefore, the planned closure process appears to be a long time at first glance. In fact, however, it is not.

Mar 2, 2022

By Ruiren Jin

In alkaline pulp, galena is depressed by sodium carboxymethyl cellulose (NaCMC), while Cu(II)-activated sphalerite exhibits a high flotability so that satisfied separation can be achieved. In addition to hydrogen bonding, chemical bonding of NaCMC with galena is confirmed by IR; only hydrogen bonding is involved between NaCMC and Cu(II)-activated sphalerite. It is also found that the greater the degree of substitute and polymerization of NaCMC, the stronger the depressive effect of NaCMC and that lower stirring speed favors the depression.

Jan 1, 1987

By Davar Abi-Zadeh, Cillian Brown, Deepak Kandra

"Grout backfill strategy for a particular subsurface concrete tunnel (~4.9km long, 3.5m in diameter, carrying 20” gas pipeline) was based on achieving 1:100 slope of the fill in order to progressively fill the tunnel, in a series of 350m section. Grout rheology, particularly its non-Newtonian and thixotropic behavior, determines the final fill slope for given backfill strategy. The objective of this study was to simulate the two-phase grout mix backfill process using Computational Fluid Dynamics (CFD) and determine the slope of the fill to validate and optimize the backfill strategy. Three dimensional CFD study showed that for a 500m long tunnel section with a single injection point of grout, given its rheology, it will likely keep flowing without filling the 500m section height wise. Design optimization for filling was carried out using two dimensional studies to make the backfill process “slope independent” by incorporating a 2.5m high bulkhead at ~1,000m. INTRODUCTION As part of a gas field development a 20” onshore gas pipeline is required from the landfall site to the processing terminal some 8km inland. At the landfall site the gas pipeline is routed in a ~5km underground tunnel underneath a bay. For operational reasons and planning consents as well as to mitigate environmental impact based on an environmental impact study, once the gas pipeline and the associated services and spares have been installed, the subsurface gas tunnel will be fully grouted. There will be no permanent access to the tunnel after construction is completed and the site compounds have been reinstated once works are complete. One of the key requirements is that “full grouting of the tunnel” is desired. The grouting material used is a non-Newtonian and thixotropic fluid mixture of bentonite, cement, plasticizer, retarder/stabilizer and water. The tunnel is filled progressively in 350m sections using a combination of existing and new pipework assuming the grout rheology will yield a fill slope of 1:100 in a 350m section. The proposed grouting system used one pump at the grouting compound to pump the grout into the tunnel using the existing tunneling pipework. For the longer runs a second booster pump was used in series to pump the grout to its final discharge location. The filling process is controlled via a system of flow meters, pressure transmitters and a tunnel CCTV system."

Jan 1, 2016

By Xun Luo, Yi Duan

A field trial of by distributed optical fiber sensing (DOFS) technique was conducted at a longwall coal mine in Australia. This investigation was designed to assess the applicability of DOFS for microseismic monitoring in mining. The experiments used commercially available optic fiber cables, geophones and associated data acquisition instruments – a fiber interrogator and a seismic recorder. The fiber cable was deployed in a 300m deep hole and in trenches of approximately 3.5 km long on the ground surface around and across the longwall panel being mined. The results obtained from the experiments have shown that DOFS is able to acquire microseismic data with quality that is comparable to geophones. It has been proven that DOFS can achieve higher spatial resolution for seismicity sensing and higher accuracy for locating events than a geophone network. These characteristics are particularly useful for using DOFS to monitor ground vibrations associated with ground caving processes and rock fracturing events induced by mining and civil engineering. It was also found that far more additional seismic events were recorded by the fibers than by the geophones. Automated data discrimination and processing methods must be developed in order to utilize DOFS for real-time applications.

Apr 26, 2022

By L. P. Johnson

Longwall mining has gained acceptance as a safe method of maintaining coal production where conventional systems were unsuccessful or uneconomic due to bad roof conditions (Kuti8). One of the major problems confronting American operators involves the correct choice of equipment which should be selected to suit the local mining and geologic conditions for optimum productivity. To achieve this, factors such as rock strengths, local geology, panel geometry, and panel orientation must be examined to optimize production and minimize down time due to ground control problems. Little quantitative information is available in the literature regarding the effects of geologic conditions on American longwall operations, and past implementations of longwall systems appear to have been based largely on experience. When mining engineers are able to assess the geologic conditions both quantitatively and qualitatively, they can more fully optimize equipment selection and panel design.

Jan 1, 1977

By A. K. Kelly

Potash was first discovered in Saskatchewan in 1943 but its continuous extraction did not begin until 1962. In the years since then, potash has played an important role in the economic and political life of the province. And, as is well-known, the most eventful time in the life of the industry occurred in 1975 when the Government of Saskatchewan decided to become a major participant in potash production. To understand that decision, however, requires an understanding of the economic development of Saskatchewan and of relations between the industry and the government prior to 1975. This year, Saskatchewan celebrates its 75th year as a province. For most of those years, we have been an agrarian economy and society, dependent on exports of cereal grains, mostly wheat, for a livelihood. Even today, agriculture accounts for about 25% of the province's Gross Domestic Product (Economic Review, 1979, p. 7) and difficulties in agriculture spread rapidly to the rest of the provincial economy. The difficulties and risks that go hand in hand with being a "one crop" economy were known as long ago as 1920 but were not fully appreciated until the combination of depression and drought in the 1930's turned the prairie grain- belt into a dustbowl. Some idea of the severity of the depression is revealed by the following data: in 1928, Saskatchewan produced 321 million bushels of wheat. By 1931, the total fell to 132 million bushels and, in 1937, to a mere 37 million bushels. The value of agricultural products sold off farms fell from $273,000,000 in 1928 to a meagre $51,000,000 in 1937. The impact of such a fall of agricultural incomes was catastrophic since about 70% of the population of some 921,000 persons lived in rural, agriculture-dependent areas (Britnel.1, 1939, p. 14).

Jan 1, 1980

By David A. Newman

The Geomechanics Classification (Bieniawski, 1979) was modified for entry and roof support design in underground room-and-pillar coal mines. Adjustment multipliers were introduced to incorporate the influence of strata weatherability, high horizontal stresses, and the roof support reinforcement factor into the existing classification system. Sixty-two case histories of both standing and fallen mine roof were collected from two mines in the northern Appalachian coalfield. Twenty-seven engineering and geologic parameters were recorded for each case. A partial correlation analysis was carried out on the cases to establish which parameters have a significant impact upon the supported stand-up time of coal mine roof. Survival analysis, a statistical technique used in medical research to assess the effect of a drug or treatment on a patient's life expectancy, was conducted together with stepwise multiple regression to derive values for the adjustment multipliers. A practical example is included to illustrate the application of the modified Geomechanics Classification to underground coal mine design.

Jan 1, 1985

By N. Dahmen

The Robbins Mobile miner has been in development for more than ten years. Two machines have been trialed in mining environments. While day to day performance to date has fallen short of the levels anticipated, instantaneous performance has been impressive for given rock conditions and continues to encourage further development. The Pasminco mobile miner has been committed for a 1.8km main decline extension at Broken Hill. M.I.M. Holdings, parent company of Mount Isa Mines, owner of the first mobile miner, are considering a new machine for McArthur River. Robbins, Pasminco, and The Centre for Mining Technology and Construction have, joined forces to accelerate development of .mechanical rock cutting techniques in general, and of the Mobile Miner in particular.

Jan 1, 1995

By M. S. Enders

The McDonald deposit is a volcanic-hosted epithermal gold resource that is estimated to contain 251,000 kg of gold in 375 Mt of ore at an average grade of 0.7 g/t gold. Phelps Dodge exploration geologists, working for the Seven-Up Pete Joint Venture, discovered the deposit in 1989. By the end of 1992, 494 drill holes for over 113,000 m of drilling, bulk sampling, soil geochemistry, geophysics, metallurgical testing, engineering, and environmental studies had been completed to support feasibility studies. The discovery of McDonald required vision, persistence, and commitment of everyone from the geologist on the drill rig to the senior management of the company.

Jan 1, 1995

By Alizeibek Saleimen Nader

The intensive use of computers for mineral application at Serrana's phosphate mine in Jacupiranga, State of Sao Paulo, Brazil, began in the late seventies. The early hardware and software available are described in sufficient detail to allow comparisons between that solution and the new one, based on a personal computer and a new software package - PC MINE SYSTEM from GEMCOM SERVICES INC - that provides full color graphics capabilities plus mine design and planning tools. The process needed for adaptation to the new technology' and its impact on SERRANA S.A. DE MINERACAO are described. Finally, future enhancements to the System and mine control and planning are focused.

Jan 1, 1989

By A. K. Stagg

Toxic substances in On solutions can retard biological leaching of copper sulfide dump ores. On solutions were analyzed for metals, organics, and chloride, and showed inhibitory concentrations of aluminum, manganese, and chloride. Inhibition of bacterial activity by the solid fraction of On solution, with and without the organic constituents, was evaluated. Toxicity to bacterial species was evaluated by monitoring bacterial numbers, pH, Eh, and rates of iron oxidation. The On solution solids were toxic at 50 -60% of their field concentration. Most of the toxicity of the On solution was due to the organic fraction. Different SX reagents show varying degrees of inhibition of T. ferrooxidans. Bacterial inhibitory effects of carriers and lixiviants used in the SX plant should be determined so that entrained SX reagents do not retard biological dump leach systems. The reagents used should be the most cost effective and the least toxic.

Jan 1, 1994

By A. C. Smith, J. H. Rowland III

The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) established a Technical study panel (the Panel) to provide recommendations on the utilization of belt air and new technology that may be available for increasing the fire resistance properties of conveyor belt used in underground coal mines. The Panel Report recommended use of the belt evaluation laboratory test (BELT) as the method for testing and approval of flame resistant conveyor belts used in underground coal mines. The research conducted to establish the correlation of the BELT with large-scale belt fire flammability tests was done using 91 - 107 cm (36- to 42-in.) wide conveyor belt. Due to today’s coal haulage capacity, the mining industry is using 183 cm (72 in.) and wider conveyor belts. The U.S. National Institute for Occupational Safety and Health (NIOSH) conducted a study to determine if the BELT will also qualify wider belts as fire resistant for use in underground coal mines. This paper describes the results of recent experiments comparing results from using the BELT and the large-scale tests for six different belts.

Jan 1, 2011

By Henning Schwarz, Faisal Al Arifi, Anas Almousa

"The Riyadh Metro Project forms part of a complete new public transport system integrated in the urban planning and development of the fast growing capital city of the Kingdom of Saudi Arabia. The Design & Build project consists of 176 km of a new metro network with 57 km of double track single tunnel infrastructures, spread over six metro lines. During the design phase, geological, hydrogeological, geotechnical and geophysical site investigations were undertaken to chart the, previously uncharted, underground construction space. Different TBM solutions were selected for implementation taking due consideration of the ground conditions of each metro line. The results obtained from deep excavations for underground stations and analysis of the TBM tunneling data will be used as key input for future tunneling projects in the Riyadh and the Kingdom of Saudi Arabia. The present paper details the design conditions and presents the solutions for large diameter tunnels in karstic limestone. INTRODUCTION The High Commission for the Development of Arriyadh was established in 1974 as the organizational, planning, executive and coordinating body responsible for the development of Riyadh. Arriyadh Development Authority (ADA), established in 1983, is the High Commission’s executive, technical and administrative arm. The ADA is responsible for implementing the High Commission's organizational, planning, executive and coordinating decisions and missions (ADA 2015). One of the remits of the ADA is the preparation and execution of a transport plan for the city. The metro network is planned to be the backbone of the public transport system developed as part of the King Abdulaziz Project for Riyadh Public Transport in Riyadh. With six lines and a total length of 176.5 km (Table 1) and 85 metro stations, the metro network will cover most of the densely populated areas, public facilities, and the educational, commercial and medical institutions. The network will connect the King Khalid International Airport, the King Abdullah Financial District, main universities, Riyadh downtown and the public transport center. The public transport plan includes a future bus network with 22 lines on 1200 km and 6765 stops that will be the main feeder for the Riyadh metro network; it will also be the main mode of transportation within and around Riyadh districts (ADA 2015)."

Jan 1, 2016

By H. EI-shall

The conventional beneficiation scheme for Florida phosphates involves reverse flotation with an intermediatory acid scrubbing step. A single reagent flotation process, using fatty acids or amine as the collector, would eliminate the scrubbing step along with the other flotation step. This can not only simplify the process flowsheet, but also result in reduced reagent costs. The potential of single reagent flotation of Florida phosphates using fatty acids as the collector was examined in this study.

Jan 1, 1993

By P. Rusin

Toxic substances in On solutions can retard biological leaching of copper sulfide dump ores. On solutions were analyzed for metals, organics, and chloride, and showed inhibitory concentrations of aluminum, manganese, and chloride. Inhibition of bacterial activity by the solid fraction of On solution, with and without the organic constituents, was evaluated. Toxicity to bacterial species was evaluated by monitoring bacterial numbers, pH, Eh, and rates of iron oxidation. The On solution solids were toxic at 50 -60% of their field concentration. Most of the toxicity of the On solution was due to the organic fraction. Different SX reagents show varying degrees of inhibition of T. ferrooxidans. Bacterial inhibitory effects of carriers and lixiviants used in the SX plant should be determined so that entrained SX reagents do not retard biological dump leach systems. The reagents used should be the most cost effective and the least toxic.

Jan 1, 1994

By R. M. Jacobs

Can your company afford to issue a check today for $100,000, $500,000, $2,000,000, or $22,000,000? This is what it might cost your company if it is on the losing end of a product liability suit. During the past 10 to 15 years, the number of product liability actions has grown from a handful per year level to a hundreds of thousands per year level. Settlements and awards in the tens and hundreds of thousands of dollars are not unusual in these days. The largest award that the authors haw heard about is a case involving a private airplane and the death of four men, which was awarded over $22,000,000. In the materials handling field, a fork lift truck, ordered with an overhead guard, was delivered without a guard because one was not available at the time. An accident with serious personal injury followed. Wouldn't it have been better to have waited until the guard was available before delivering the unit? Answer: a quarter of a million dollars better -- the cost of the settlement. Hoisting devices are also not without their liability precedents. In a 1960 case, an employee was injured when a load abruptly fell from a hoist. It was determined that the operator could not possibly have caused such a fall had the hoist been functioning properly. The case was compounded when the manufacturer of the hoist contended that the load had been improperly connected to the device, since the same hoist was used to remove the weight from the injured man without another malfunction.

Jan 1, 1973

Mill #4 processes mildly refractory ore from Carlin Trend deposits. Diagnostic analysis of plant operating data was used to generate a mathematical model containing the important parameters influencing gold recovery. The model was used to direct modifications to plant operating practice. The cyanide-dosing strategy was changed to reduce gold losses from preg-robbing and to cut reagent consumption. A finer grind was achieved without capital investment. The density in the carbon-in-leach circuit was lowered, and tighter control was exercised over the plant throughput. These changes resulted in a recovery increase of at least 2%, worth $111,000/month at $300/oz ($9.64/g) gold, and concomitant reagent cost savings of $55,000/ month.

Jan 1, 2000

By J. W. Parkinson

With most of the coal currently mined in the eastern U.S. already requiring cleaning to meet electric utility coal specifications, the question remains how medium- and high-sulfur coal producers will provide the even better quality coal expected to be demanded if pending acid rain legislation is enacted. One emerging approach is to crush the coal to liberate additional ash and sulfur so that better quality coal can be produced at equal yields. This paper discusses how to measure liberation. the premiums the utility market is willing to pay for lower sulfur coal, and a staged middlings crushing scheme that promises the benefits of total raw coal crushing but at lower costs. For some coals, cautious application of liberation concepts may be the only way to produce a product that can be quality and cost competitive in the future utility coal market.

Jan 1, 1988

By P. M. Lin

This paper presents an overall stabilization method to eliminate the potential of reoccurrence of subsidence over abandoned mine lands. The method considers column grouting at the specific locations inside the subsidence influence areas including the distressed and stress concentration zones instead of grouting' around and beneath the damaged structures. The later method is commonly used for AML subsidence abatement at the present. By using finite element method the conditions of stress distribution in the strata before and after grouting can be calculated. The design of grout pattern includes the location and number of the grouting holes. Based on the calculation, the proposed method significantly reduces the stress concentration, i.e., the potential of reoccurrence of subsidence can be reduced or eliminated. A comparative analysis including number of grouting holes, grout affected area, stress level, and potential of subsidence reoccurrence will also be presented.

Jan 1, 1990

By C. N. Logan

The Southern Company is one of the nation's largest electric utilities and is the parent firm of five operating companies: Alabama Power, Georgia Power, Gulf Power, Mississippi Power and Savannah Electric and Power. Another subsidiary is Southern Company Services (SCS) which provides engineering and technical sup-port to the five operating companies. This technical support includes the procurement and supply of over 40.9 Mt (45 million st) of coal annually for the 22 coal fired plants in the system. Approximately 80 percent of this tonnage is purchased under long term contracts and the remaining 20 percent is purchased on the spot market. The coal is principally supplied from Alabama, Illinois Basin and the eastern Appalachian coal fields. Most of the coal is delivered by unit train and barge but one plant in Alabama receives all its coal by truck and conveyor belt.

Jan 1, 1990