Search Documents

By L. R. McCullough

To compete in Today's Market, Mine Managers have two, often conflicting tasks. They are to improve productivity, allowing the mines to compete in our world markets and to improve the environment in which our miners must work. To Maintain and improve the environment to ever increasing acceptable levels requires monitoring. In years passed this required considerable labor, which was provided by the Ventilation Department. They continuously took manual samples using hand-held instruments, sampling gas level such as CO for fire and methane for explosive risks. In addition they took continuous air velocity readings with hand-held instruments which allow them to calculate the ventilation air movement in each area of the Mine. This manual gathering of information was not only expensive and slow but marginal at best. It was marginal because the gas sampling was sporadic rather than continuous, as sample reading taken in one part of the mine would likely not be repeated for another 8 hours. If problems did occur, they likely went unobserved until they reached crisis proportion.

Jan 1, 1990

By J. B. Yianatos

This paper addresses the impact on performance of column height (H), and column height to diameter (H/D) ratio by modelling the effect of HID on mixing and consequently on recovery and grade. Mineral recovery increases with increasing H/D ratio for a constant column volume and feed flowrate, while the concentrate grade decreases to a minor extent. Columns 10-15m in height with H/D-10 are well suited for feed rates 150-600 L/min. Maximum H/D is determined by the gas carrying capacity, an important consideration for pilot units where H/D?200.

Jan 1, 1987

By William Tattersall

On behalf of my agency, the Mine Safety and Health Administration, I would like to add my appreciation that all of you could be here today. Previous dust symposia over the years have proved the value of close cooperation among universities, government agencies, and professional societies in advancing knowledge of dust research and development in the interest of miners and the industry. I'll just comment briefly on MSHA's part of the overall effort by all parties to control miners' exposure to respirable coal dust and other airborne dusts. As you know, our agency's congressional mandate is to do what is necessary to assure that miners will have safe and healthful workplaces. In the area of coal mine health, this has meant joining with the mining community in a continuous campaign to keep respirable dust and quartz levels below applicable standards to prevent or reduce disabling coal workers' pneumoconiosis and silicosis arising from excessive exposure to respirable quartz. Currently, our agency is processing about 120,000 coal dust samples taken by MSHA and company people during the year and about 8,000 samples taken from metal and nonmetal mining operations. Our dust program, like other MSHA programs, has benefited from increased computerization of records. The attack on CWP has had the highest priority of government and industry. The goal has been to sharply reduce social costs of suffering victims and their families as well as the associated future payments under the black lung benefits program. During the 1989 fiscal year, about 104,000 former miners received about one and a half billion dollars in benefits. Since the program began, nearly 25 billion dollars have been paid out. Much progress has been made in lowering dust levels in coal mines since the standard of two milligrams per meter of air was established in 1972. Before that time, there was a 4-to-10-percent probability of a miner developing coal workers' pneumoconiosis at typical pre-1972 exposure levels. However, under the maximum respirable dust levels allowed today, this probability has been reduced to about 1 percent. Since average dust levels are lower today, we can expect fewer miners to develop CWP in the future. Out goal continues to be elimination of both coal workers' pneumoconiosis and silicosis in both coal and nonmetal mining. In 1985, MSHA revised its coal mine quartz policy to allow mine operators to submit dust samples used in setting the quartz standard. Previously, only single MSHA samples were used. Even though less than half of the mine operators have taken advantage of this change, it has provided a larger population of samples for analysis then before. Also the policy allows operations that are on a reduced quartz standard to have the standard reviewed every six months. In underground coal mining, the job of roof bolter typically has higher than normal exposures to quartz. About 45 percent of respirable dust samples from roof bolting operations contain more than 5 percent quartz and therefore are put on a reduced quartz standard. One objective of the policy revision was to improve miners' health by follow-up monitoring, and this is being done with roof bolting jobs. MSHA studies of surface coal mining operations have provided data showing that bulldozer operators and highwall rotary drill operators often have high exposure to quartz dust, and our agency is directing enforcement efforts to reducing this hazard. One of the most important responsibilities of MSHA's metal and nonmetal mine health division is the respirable dust sampling program. In the last few years, nearly 3 out of 10 samples have

Jan 1, 1991

By Kousik Sinha

The advantage of using a clean coal as a feedstock in a direct liquefaction plant is improved performance of the plant by several factors e.g., increased throughput of coal; reduced wear and tear of valves, pipes, and pumps; increased liquid yields, etc. This paper examines the technical feasibility for cleaning Illinois #6 coal as a feedstock to a direct coal liquefaction plant via selective agglomeration using a coal-derived heavy distillate, Wilsonville V-1074 as agglomerant. Effects of addition of Kerosene or coal-derived Naphtha as conditioner, coal particle size, slurry pH, oil to coal ratio, and operating temperature on ash reduction and clean coal weight recovery have been studied. Results show that about 70% of the ash can be removed from this coal and the clean coal weight recovery over 85% can be achieved by using this technique with suitable selection of coal particle size, slurry pH, mixing intensity and oil to coal ratio.

Jan 1, 1991

By E. R. Bauer

The ground control aspects and occupational safety concerns of extended depth-of-cut mining are presented in this U.S. Bureau of Mines (USBM) report. The scope of extended cut use and typical face operations while extracting extended cuts is reported. A comparative review of roof fall fatalities and a statistical analysis of accidents and injuries for both extended and nonextended cut mining is included. The views and opinions on extended cutting from a series of interviews with mine workers in five states are summarized. In addition, some of the problems and safety concerns of this extraction system are mentioned.

Jan 1, 1995

By Rakesh Sehgal, Pushkar Verma, Mohit Sharma

"SJVN Limited successfully commissioned its Rampur HEP (412 MW) in 2014. The project has been planned to operate in tandem by directly utilizing the Tail Water of SJVN’s prestigious Nathpa Jhakri Hydro Power Station 1500 MW located upstream. The initial filling of voluminous water conductor system of RHEP with 10.50 m diameter, 15 Kilometer long Head Race Tunnel, involved more than 1.5 million m3 of water. The filling operation of such a large diameter tunnel constructed in young folded Himalayas which always offer less ideal sites for tunnelling and their subsequent operations under pressurized conditions is worth sharing with tunnelling fraternity. The paper covers meticulous planning, execution, precautions taken, and performance monitoring during filling process keeping in view the fragile geology, low rock cover zones, shear zones in close vicinity of thickly inhabited areas, squeezing zones, hot water zones encountered during excavation.1.0 RAMPUR HYDRO POWER STATION IN BRIEFRampur Hydroelectric Project (412 MW), is located in Himachal Pradesh (India). This project is a downstream development of Nathpa Jhakri Hydro Power Station (1500 MW) constructed on river Satluj and commissioned during 2003. Both the projects today are now successfully working in tandem. The upstream NJHPS has been constructed on the left bank of the river while the downstream Rampur HPS is located on right bank of the river (Figure-1).The major length of HRT of Rampur project lies on right bank of river before it crosses under the river in its initial reach (Figure-2). The main features of the project are as below:• 10.50 m diameter 15 km long HRT ending in a 155.75 m deep, 38.00 m diameter surge shaft.• 3 steel lined pressure shafts, 5.4 m dia, 211-220m long.• Surface valve house 69 m long x 10.50 m wide x 23 m high housing 3 No. butterfly valves• 3 No. surface penstocks 5.4m dia 368-382m long, bifurcating into six penstocks, each of 3.80 mdia. to feed six generating units of surface power house 158 m long x 24.50 m wide x 48 m high, with Francis turbines each of 68.67 MW capacity."

Jan 1, 2016

By C. Leal

Modern production has as goal to reach high and uniform quality in their products. To success with this, it is essential to have a good knowledge of the different variables involved in the process. Investigation or analysis of a process or system has as references the measurements of the variables. These measurements are presented normally in form of data. These data are measured in intervals over time. The aim with measurement of the data in a process is to obtain information about the state of it in order to have it under control. Other goal is to know how the results are affected by the process variables to improve upon product quality, redunding manufacturing cost, better pollution control etc.

Jan 1, 1994

By J. H. Kempton

The scrutiny given to model predictions of pit-lake water quality has focused attention on the uncertainty associated with long-term predictions. Although comparison of probabilistic predictive modeling of water quality in existing pit lakes indicates that short-term predictions can bracket most parameters, uncertainties in wall-rock reactions and the stability of groundwater composition and climate remain unquantified. This overview of the uncertainties associated with longer-term predictions is presented as support for those considering policy decisions that must be made in the absence of reliable estimates of future conditions.

Jan 1, 1998

By Klaus Grebe

Recent investigations by Mannesmann Research have shown that disintegration of sinter with widely varying quality levels is subject to a much more complex set of influences than was previously assumed. It was confirmed that disintegration at temperatures between 300 and 600 °C is triggered by the degradation of hematite. The specific tendency of hematite to disintegrate is, however, not constant: sinters containing the same amount of hematite can show widely differing disintegration tendencies depending upon structural homogeneity, porosity and gangue quantity. Especially sinters with heterogeneous structures transmit stress to the hematite phase and this favours disintegration. Another factor is the brittleness of the glassy silicate phase, which can be influenced even by small modifications of minor gangue constituents.

Jan 1, 1981

By William Gleason

The evolution of technology has made the world a more connected place. It continues to change the way we power our homes and vehicles and is leading to a future that seems to be limitless. Limitless as long as we can continue to supply the minerals necessary for technology to produce better iPhones, more efficient electric cars, better wind turbines and sophisticated national defense systems. These minerals, dubbed critical minerals, have surged in importance in every corner of the world and, on Aug. 3-4, they were topic of conversation at the Critical Minerals 2014 conference in Denver, CO. The conference, hosted by SME and the Australasian Institute of Mining and Metallurgy (AusIMM), looked at critical minerals from every angle, from where they are found to what the future might be. Among the minerals that have been called critical are rare earths, a collection of 17 minerals that have become increasingly important as technology continues to advance in everything from communications to energy to national defense. Leading off the conference, David Abraham, senior fellow at the Institute for Analysis of Global Security, explained that, like many people, he is relatively new to rare earths. Unlike most people, though, Abraham developed more than a passing interest in the minerals and has since travelled the world to understand the role of rare earths ? where they are found, how they are mined, how they get to market and, eventually, what applications they are used in. Following his travels, he said he returned concerned about the sector and how the industry will keep up with the demand that only seems to be growing in the modern world. And, Abraham noted, that it is not just the developed world that is driving demand. It stretches even to places like Indonesia, where the average annual income is about $3,000/year. Yet, the nation is one of the most active places in the world for social media with a population that is wired in with all kinds of electronics. The problem facing the sector is, and has been for a long time, and especially since 2010, supply of the minerals. At one time, China produced about 98 percent of the world?s supply and controlled the sector completely. In 2010, as the world began to demand more rare earths and develop other sources, China announced an export ban on rare earths. This changed the game completely, from the production lines all the way to the floor of the U.S. Congress.

By R. W. Macqueen

Organic matter commonly associated with Mississippi Valley-type (MVT) lead-zinc deposits may be used to assess the burial/thermal history of host rocks and sulfides. Organic matter may also have been involved in the genesis of H2S required to precipitate sulfide ores. Pine Point, Northwest Territories, Canada, provides an example. Located on the south shore of Great Slave Lake, Pine Point is an operating world class deposit which has produced 58 million tons of ore containing 3.0 percent Pb and 6.1 percent Zn from more than 40 Individual orebodies. Well-documented paleokarst features in a Middle Devonian carbonate complex are the main ore hosts. Sphalerite and galena ores are mainly open space fillings, and, from fluid inclusion studies, were deposited from saline fluids at temperatures of up to at least 100°C. Forms of organic matter occurring in the Pine Point barrier-reef complex Include indigenous organic matter, heavy oil and bitumen. Based on numerous geochemical criteria, it is clear that heavy oils and bitumens were derived locally from indigenous organic matter. The geochemical character of the Indigenous organic matter demonstrates that the barrier-reef complex is immature to marginally mature with respect to petroleum generation, and has not been heated above about 60°C maximum. Thus sphalerite with fluid inclusions that yield temperatures up to about 100°C represents former thermal anomalies. Bitumen is of two main forms at Pine Point: widespread soft, tarry material soluble in organic solvents (unaltered bitumen); and hard, brittle, glassy material that is mostly solvent-insoluble, and associated with white sparry dolomite and lead-zinc ores (altered bitumen). There are also partly altered bitumens. Unaltered bitumens have atomic H/C ratios of about 1.4, sulfur contents averaging 7.8 percent, and sulfur isotope ratios 634S) of approximately +4.6 per mil. Altered bitumens have atomic H/C ratios averaging 1.02, sulfur contents averaging 22 percent, and 634S values of about +12.9 per mil. These data and the organic geochemical character of a large suite of bitumen samples analyzed, strongly support the concept that some bitumen has been involved in the thermochemical reduction of sulfate to produce the H2S required to precipitate the ores. Mass-balance calculations indicate that the amount and degree of alteration of bitumen is more than enough to account for the reduced sulfur species deposited as metallic sulfides at Pine Point. MVT deposits, including Pine Point, seem to require the coincidence of available metallic Ions, pre-existing pore space, and a precipitating agent. A close look at organic matter in more MVT settings may outline trends in distribution or alteration which can be used as indicators of past thermal environments and processes of ore deposition.

Jan 1, 2013

By L. Zhou, L. Yuan, R. A. Thomas, D. Bahrami

The abstract emphasizes the importance of a calibrated ventilation network model for mine ventilation planning, optimization, and fire simulation. It highlights the impact of continuous airflow monitoring on improving model calibration. The paper discusses an experimental study at the Safety Research Coal Mine (SRCM) to understand the use of continuous airflow data for model improvement. It also addresses practical problems in calibration and tuning using this data, including analysis of air velocity sensor fluctuations and application of sensor location correction factors for accurate average air velocity.

Mar 7, 2022

By R. Venugopal, V. K. Saxena, Veerendra Singh

"Ore morphology plays a vital role during the milling and liberation of minerals. This study was carried out to understand the role of mineral crystallography and mineral interfaces on the milling and liberation processes. Data related to mineral crystallography, Vickers Hardness Number and beneficiation processes were collected from literature, and detailed statistical analysis was conducted to relate these parameters. Review of the crystallographic information of minerals present in ores indicates that molecular weight and cell parameters significantly affect milling and liberation characteristics. Mineral interfaces were classified into the three categories of coherent crystals, semi-coherent and incoherent crystals, and breakage behaviors were studied. The studied cases revealed that these material interfaces control the micropore properties that play a vital role in the initiation of intergranular and intercrystalline fractures which occur in siliceous manganese ores and dolomite as a result of thermal treatment. In contrast, banded hematite jasper and coal exhibited a much more complex fracture pattern due to their coherent interfaces and finer physical associations. This study explains the effect of the various types of interfaces on milling, and the approach can be helpful in developing a methodology to enhance mineral liberation with minimum energy consumption.IntroductionComminution is a vital unit operation in the mineralprocessing, cement-making, power-generation and pharmaceutical industries. Its importance in mineral beneficiation operations is increasing every year as a result of the growing need to exploit lower-grade ore bodies and process reject materials (Blazy et al., 1994; DOE, 2005). Low-grade ores require significant energy during grinding to liberate the valuable minerals, which are further separated from the gangues by various beneficiation methods. Various attempts have been made to enhance mineral liberation during grinding to minimize energy consumption. Most of these studies focused on the analyses of the compression mechanism, chemical additives, thermal treatment, microwave treatment and electric disintegration (Klimpel and Austin, 1982; Norgate and Weller, 1994; Bearman et al., 1997; Kumar et al., 2010; Wang et al., 2011; Singh et al., 2012). However, many of these efforts had limited success, and there is a need to see the problem from a fresh perspective."

Jan 1, 2015

By W. P. Arnott, P. Nascimento, X. L. Wang, K. C. Kocsis, S. J. Taylor, H. Firouzkouhi

We report the first spectral photoacoustic measurements of silica, coal, and kaolinite dust absorption coefficients from 11 to 13 μm at 5 nm resolution made with a tunable quantum cascade laser. This is important because airborne silica dust and coal dust within mining environments continue to be a problem for mine workers and staff due to their severe health effects on the respiratory system, while other dust types are potentially interferents to their detection. Our real-time spectra compare favorably with the non-real-time filter-based Fourier transform infrared spectrometer (FTIR) spectra obtained using the sampling system developed by NIOSH for their end-of-shift method to determine silica dust concentrations using a portable FTIR. We discuss our new dust generation system and instrument testing chamber. We also show that our PM4 silica mass concentration measurements by a low-cost air quality sensor (SPS30) are in good agreement with the TSI Aerosol Particle Sizer instrument, the NIOSH end of shift method, gravimetric mass, and correlate well with photoacoustic light absorption measurements at a wavelength where silica absorbs strongly.

Aug 20, 2022

By Taghi Sherizadeh, Paul Brooks, Dogukan Guner, Samuel Nowak

Large excavations are well known to result in rock mass deformations which can present challenging situations for mine personnel. Most of the currently available ground movement monitoring devices fail to adequately provide mine operators with highly accurate and meaningful insights into rock mass deformation or displacement. The use of distributed fiber optic sensors (DFOS) in industries such as oil and gas and civil engineering has shown the potential of these sensors to deliver real-time, highly accurate, and long-range distributed strain measurements with great success. However, the use of these sensors in underground mining is limited to a few case studies.

By D. Van Orden, Y. Kamiya, R. Lee, E. Ilgren

Crocidolite is a well-known causative agent for mesothelioma. However, studies have shown that the pathogenicity of the fiber from different mines varies considerably and it has been postulated the parameter that appears most likely to account for this variation is fiber width although this has never been formally confirmed. To date, crocidolite appears to be the only asbestos mineral for which an epidemiological study comparing the risk of mesothelioma in a population exposed to ‘thin’ fibers with another exposed to ‘thick’ fibers of the same species may be carried out. Finnish anthophyllite, South African amosite, and African Transvaal crocidolite can also be classified as thick fibers, and there is a paucity of mesotheliomas in populations exposed to them compared to those exposed to thin Cape crocidolite. No thin occurrences of these minerals are known. Our previous study looked at crocidolite from several sources. The present study considers the amphibole anthophyllite found in many places in the world. This mineral, regardless of source, does not show the same variation in fiber width found with crocidolite from different areas. All anthophyllite fibers that have been mined may be classified as thick and populations exposed show very low levels of mesothelioma. We suggest the most likely explanation is related to the fiber width distribution and a concomitant reduction in the ‘Stanton fiber size’ fraction.

Jan 1, 2012

By I. H. Warren

The high temperature lubricant molybdenite, MoS2, is usually produced by a complex sequence of processes involving mineral dressing of molybdenite concentrates followed by leaching with hydrofluoric acid to remove abrasive impurities such as silica (1). Many attempts have been made, mostly by techniques involving, direct fusion of molybdenum compounds with sulphur, to produce synthetic molybdenite. However, apart from some experiments of geochemical interest (2) in which aqueous solutions of sodium sulphomolybdate, Nat MoS4, were decomposed under pressure at temperatures between 300°C and 700°C, no attempts to produce the mineral by hydrometallurgical procedures have been reported. Since molybdenite is nominally a compound of tetravalent molybdenum with sulphur, and the most common state of molybdenum is +6, production of molybdenite is likely to involve reduction and sulphidization. The present study, therefore, describes the reduction, with hydrogen and carbon monoxide, of molybdenum in the hexavalent state in alkaline aqueous solutions containing sulphide ion. In these

Jan 1, 1972

By Karin Bäppler

"When considering large-scale infrastructure projects worldwide special attention has to be paid to the large diameter tunnel construction projects that were successfully completed in the Southern Hemisphere. The projects that are highlighted in this paper are large-scale infrastructure projects in the sector of transport. In focus are four road tunnel projects that were constructed in Australia and New Zealand using mechanized tunnelling technology. The tunnel boring machines (TBMs) that were reliably applied to these four major projects all exceed the bore diameter of 12 meters. These TBMs are therefore in the range of large to very large diameter TBMs. The technology used demonstrates state of the art technology with tailored tunnelling technology adapted to the specific project demands. Two Double Shielded Hard Rock TBMs (Ø 12.35 meters) were used for the construction of the Clem Jones Tunnel in Brisbane crossing beneath the Brisbane River and these two machines have been reused for the excavation of a 4.3km long two-lane highway tunnel for Legacy Way in Brisbane creating a new traffic artery towards the city centre. Two EPB Shields (Ø 12.48 meters) excavated and lined the twin-tube road tunnel for the Brisbane Airport Link. Excavation diameters in excess of 14 meters, such as the Earth Pressure Balance Shield (Ø 14.41 meters) involved in the Waterview Connection Project in New Zealand, are understood in the tunnelling industry as very large diameters. The machine is customized to the requirements and subsurface conditions of Auckland. The paper spotlights the large to very large diameter TBMs that were used and focuses on the comprehensive solutions developed by the machine manufacturer to provide a system with benefits for the contractor especially for the Waterview Project. INTRODUCTION Extensive large-scale road infrastructure projects like the ones implemented in Brisbane (Australia) and currently under construction in Auckland (New Zealand) show the tendency of today’s infrastructure construction projects. Functional infrastructures need to be put in place to cope with the demand of mobility and flexibility of people living in cities and metropolises. Impact during construction work to people or environment has to be kept as low as possible to ensure the quality of life is not disrupted."

Jan 1, 2016

"On-site research and development as well as in-situ testing are key factors to the successful implementation of new mining equipment and technology. Unfortunately the demands and necessities of research and development often conflict with the reality of mine production in operational mines, especially during early stages of research and development and the initial testing of new equipment. Several experimental mines under university supervision attend to this problem and provide a close-to- reality testing environment for the mining industry and mining equipment manufacturers. This paper gives an overview of the design and organization of such an underground testing area as well as of the wide range of possible operations it can facilitate at the example of the FLB Experimental and Teaching Mine (Forschungs- und Lehrbergwerk) at Technische Universität Bergakademie Freiberg, the central European underground research mine. INTRODUCTION As well as the Mining Engineering education follows the same pattern worldwide, the tasks and duties to be fulfilled by engineers in the productive mines are comparable around the globe. This also holds true for the technologies and equipment needed, both in surface and underground mines. Almost all mining equipment brands are being distributed worldwide. The tasks and challenges of guaranteeing an ever- increasing productivity at the mines, while simultaneously maintaining, respectively improving, safety standards, also in the developing countries and emerging economies, requests a constant development, improvement and adaption both of the engineering education and of R&D in technology and equipment. The increasing safety requirements at the mines, in combination with also increasing safety and liability policies, do often not allow a proper practical education of mining engineering students. At the same time, new technologies and equipment to be deployed / brought to the mines have to be fully functional in a production operation from the very first moment. Time losses like break-down time or even repair and maintenance breaks are often costly and, even when expected up to a certain degree with newly developed machines, have a wider negative impact on the neighboring operations and operations within that mine, thus often being unacceptable within the ongoing production process and extremely costly."

Jan 1, 2015

By M. Eyll-Vetter

The operation of large opencast mines in a densely populated area in the centre of Europe involves an inevitable interference in the region. Thus, this is only possible with general acceptance by the regional stakeholders. In order to achieve this general acceptance, it is necessary to develop sound common concepts and to engage in a continuous dialogue with the stakeholders. The aim is to create seminal structures of relevance to the regional economy, taking into account the interests of the various stakeholders like e.g. authorities, local governments, the regional public, and churches. The recultivation of the mined-out areas represents the offset for the mining activities. RWE Power has reached high acceptance of its recultivation. This high acceptance is illustrated by various examples, from biotopes to high-yield agriculture and recreational areas. Thus, recultivation covers all the elements of sustainable development from social compatibility to ecological as well as economic aspects. This is only achievable through an intensive stakeholder dialogue in the region: The communities concerned are intensively involved in the planning and approval process for the new landscape. As far as social compatibility - one of the aspects of sustainable development - is concerned, the necessary resettlement of whole villages is one of the principal challenges. Over the last few decades, RWE Power has developed an approach that is broadly recognised by the stake-holders in the region. The best proof for this is the high proportion of resettlees taking part in the joint resettlement scheme offered. This can only be achieved by constant involvement of the stakeholders in the resettlement process. In conclusion, it can be stated that RWE Power has implemented a well-functioning stakeholder dialogue that guarantees the general acceptance necessary for mining operations.

Jan 1, 2007