Search Documents

By C. Brown, N. Rayyan, T. H. Dubaniewicz

Lithium-Ion batteries (LIBs) have the potential to go into thermal runaway which introduces a new ignition source in hazardous environments such as gassy underground mines that may contain methane in the surrounding air. Researchers from the National Institute for Occupational Safety and Health (NIOSH) used an accelerating rate calorimeter (ARC) to induce thermal runaway in individual lithium-titanium-oxide (LTO) and lithium-nickel-cobalt-aluminum-oxide (NCA) LIB cells within a sealed enclosure with either no methane, a lean, a stoichiometric, or a rich methane-air mixture in the surrounding canister to determine if these LIB types would ignite the methane, causing an additive effect on overpressures. Canister pressures and maximum temperatures reached by the cells, surrounding air, and exhausted gases were measured in this study and remained consistent with varying methane concentrations.

Feb 1, 2023

By Sandeep Kumar Jeripotula, Govinda Raj Mandela, Aruna Manglapady

Dumper operators are frequently exposed to whole body vibration (WBV) in surface mines. Surface mining activities involve the amalgamation of comparatively high intensity of vibration and extended exposure durations. Efficient risk reduction mandates knowing of important phases of a task that poses a threat to health of dumper operators. So far in India very limited studies have been reported on WBV exposure with regard to surface mines. This paper evaluates WBV of dumper operators based on ISO 2631-1:1997 Standards and European Union (EU) Directive 2002 for different phases of job cycle. Six dumpers were considered for this study and the vibration measurements were made for all the four phases of the job cycle by placing the triaxial accelerometer on the operator’s seat-surface and at the seat-back, independently. The findings of the study revealed that the haulage task (loaded travel and empty travel) remains the chief contributor to vibration exposure according to seat-surface and seat-back measurements. Maximum frequency weighted root mean square (RMS) of 1.12 m/s2 and 1.09 m/s2 were reported for empty travel task for seat-surface and seat-back measurements, respectively. For seat-surface measurements based on RMS, Z axis remains as the dominant axis of vibration for all the dumpers during haulage task, whereas for seat-back measurements, the dominant axis varies between X and Y. Exposure action value (EAV) based on RMS has exceeded the threshold value of 0.5 m/s2 for all the dumpers during loaded travel and empty travel for seat-surface as well as for seat-back measurements.

By K. R. Griffin

Atmospheric conditions underground are constantly changing and from a safety perspective, it is critical to identify when conditions are trending abnormally. Atmospheric monitoring in underground coal mines allows mine operators to analyze atmospheric conditions underground in real-time. Real-time monitoring can then be used to identify whether atmospheric conditions underground have become problematic. The implementation of a risk assessment and management process allows operators to then use a risk-informed decision making to identify comprehensive site specific ventilation parameters. Establishing risk-informed ventilation parameters and tracking conditions relative to these parameters, management can modify ventilation plans as mine conditions develop to manage evolving risks. Ventilation risk assessment and management allows developing atmospheric monitoring technologies to be fully utilized in order to increase safety standards in the United States. This paper reviews general risk assessment approaches, state of the art ventilation based risk assessment, and the risk assessment and management application within the United States regulatory framework.

Feb 27, 2013

By Malte J. M. Gurgel, Axel Preusse

Recent three-dimensional surveying techniques have opened up new opportunities for the registration and monitoring of underground cavities. There are essentially two main methods available: Laser scanning, which is used both above surface and increasingly underground, and photogrammetry, which is also experiencing a renaissance with techniques like structure from motion through the algorithm-based orientation of high-resolution images. Both methods provide the capability to reconstruct reality by various 3-D products like points clouds and meshed models. However, they differ significantly in the steps of registration and calculation as well as in the resulting evaluation options.

By J. R. Evans

In order to patent an industrial mineral placer mining claim, it must incorporate an economic deposit. Each ten acre parcel is evaluated for its mineral -in -character nature. Nonmineral -in -character parcels cannot be patented. Economic concerns include: claim locations, dummy locators, common variety nature, "excess reserves," and environmental constraints. Also, geologic and mineralogic studies, sampling and testing procedures are vital. Mining, milling, processing cost, and taxes must be evaluated. Product marketability analysis is necessary before starting any cash flow or discounted cash flow study. Valid data is essential to evaluate an economic industrial mineral deposit.

Jan 1, 1997

By R. F. Harig

Designing an underground nuclear waste repository is a complex process. Although many decisions are involved before the design is complete, the first three--what the target horizon is, what the underground boundary is, and where the entry point will be located--are important because they establish the basis for the entire repository design. Even more important than these decisions, however, is the data on which the decisions are based. Because the current data are limited, an aggressive data gathering program is needed during the next design phase to augment information about the intricate interplay among all facets of the repository design and the geologic medium in which the proposed repository is to be developed. Although unique to modern engineering enterprises, the challenges involved in designing a repository in the unsaturated zone are within current technology and engineering practices.

Jan 1, 1991

By W. Edwin Dill

For the mining industry, the Internal Revenue Code and regulations offer a range of choices in arriving at the allowable depletion. Each case is essentially unique. Two prerequisites can optimize these opportunities: communications between the mining company's tax specialists and its technical staff; and an understanding of IRS definitions. For the latter, a logical starting point is consideration of exploration and development, since they precede production and depletion is unallowable prior to production. Criteria for selecting engineering and accounting options for exploration and development indicate the necessity of interaction between these company functions to achieve the most favorable tax position.

Jan 1, 1982

By J. R. Brett

Utah Development Company (UDC) operates five large opencut coal mines in the Bowen Basin of Central Queensland, Australia. In total, over 20 million tonnes of coking coal are exported annually from the five mines. Typically, the coal seams dip at 5 percent, are 2 to 10 metres thick, and sub-crop some 20 to 40 metres below surface. In the main, the operations are single seam, but multiseam (2, 3 or 4 seams) operations do exist and will form an increasing proportion of the mining activities as depths increase. Draglines are used as the major stripping equipment, highwall depths currently ranging from 20 to 65 metres. Whilst project feasibilities were based on stripping to a 60 metre highwall, it is now proposed to continue opencut mining to depths exceeding 100 metres. This will entail large quantities of prestripping (ahead of the draglines) and overcoming problems associated with steepening seam dips, including haulage of coal from the pits.

Jan 1, 1982

By J. Noll, A. Miller, J. Volkwein, C. Pritchard

Hecla Limited, Magee Scientific and the U.S. National Institute for Occupational Safety and Health (NIOSH) combined efforts to evaluate an in situ air filtration system for use in an underground mine environment. The purpose of the collaboration was to determine the efficacy of such a technology for reducing the concentration of airborne diesel particulate matter (DPM), with the aim of improving air quality in underground hardrock mines. A secondary goal was to evaluate the use of an aethalometer as a means of real-time measurement of black carbon as a surrogate for DPM. The evaluation included measuring the DPM-capture efficiency of the filter when it was preloaded with dust. Toward this end, rock dust was introduced at the filter inlet to create a dust layer on the filter surface, with the intent of providing improved capture of the much smaller DPM particles. The filtration efficiency for DPM was assessed by comparing measurements of DPM taken at the inlet and outlet of the system, using both realtime and time-weighted-average approaches. The real-time measurements were performed with a Model AE33 aethalometer, and filter samples analyzed by the NIOSH 5040 method were used to assess the effects of the system on time-weighted-average concentrations of total carbon. Results showed a reduction in DPM concentrations in the range of 82 to 89 percent. While the calculated efficiencies based on the two different measurement methods were similar, the DPM levels reported by the aethalometer were higher, possibly due to differences in the performance of the size selectors used for the two methods: impactors versus cyclones. More research is required to develop a robust correlation between the two methods to support the use of the aethalometer in future mining applications. The advantages of the aethalometer are that it can measure and record DPM levels for weeks at a time and can be directly connected to a mine monitoring system, potentially at multiple locations. Ideally, such data can be used to initiate the startup of the filtration system should DPM concentrations reach an action level. This work demonstrated that in situ filtration systems, modified to collect DPM and coupled with real-time monitoring, show promise in reducing DPM concentrations in the mine environment.

Mar 1, 2017

By H. C. Seeber

When considering all the aspects of a viable mine plan, it is important to estimate the accurate cost of mine ventilation, which varies as a function of airway dimensions, fan selection and ventilation network. Optimization of the overall elements of ventilation design can lead to very significant cost savings when capital and operating cost savings are considered in combination. This paper will describe a methodology, whereby ventilation costs can be minimized by optimizing the ventilation aspects of mine design and fan selection, by providing a brief description on ventilation theory and the factors which affect ventilation operating and capital costs.

Jan 1, 2002

By S. Mohanta, S. Chakraborty, B. C. Meikap

"An air dense medium fluidized bed separator is an efficient dry process for the removal of undesirable gangue material from run-of-mine coal. Its cleaning performance depends on a variety of operating parameters that are interrelated in unknown, complex ways. A literature review showed that these parameters' effects had been experimentally investigated using a traditional one-variable-at-a-time approach, which is highly inefficient and sometimes misleading because many of the parameters often interact with each other to alter the overall equipment performance. Also, it is realized that the interrelationship among these parameters can have a significant effect on equipment performance. Therefore, to correctly evaluate the effects of individual parameters as well as their interactional effects on the separation performance of an air dense medium fluidized bed, we conducted a scientific study based on response surface methodology. Empirical models for two key response variables, namely, product ash and combustible recovery, were developed and subsequently used for identifying an appropriate operating region to achieve optimum separation performance. Furthermore, the optimum performances predicted from the empirical models were validated against experimental data. Preliminary results show a strong interaction among the operating parameters investigated in this test program.IntroductionFluidization is widely applied in industry for its various useful features. In the coal industry, it is used in the air dense medium fluidized bed (ADMFB) separator for the beneficiation of run-of-mine coal. In this separator, a medium is created by suspending fine magnetite particles in an upward air flow, and this pseudo-fluid is used as the beneficiation medium, with the lighter coal particles floating to the medium’s surface while heavier particles sink to the bottom. This separation technique had been receiving a significant amount of attention worldwide in recent times for its specific advantages of low operating cost and less restriction for small capacities (Luo and Chen, 2001; Sahu et al., 2009; Dwari and Hanumantha Rao, 2007; Van Houwelingen and de Jong, 2004), but it is still not a well-established industrial practice because of the availability of efficient wet processing technology. However, with a revival of interest in the dry beneficiation of coal, in general, and ADMFB, in particular, there is once again a concerted effort to improve the efficiency of the ADMFB process, and successive improvements have been made to make this process a competitive and viable option. The existing literature reveals that most of these research efforts had been essentially focused on the identification of a single parameter that has a key influence on separation performance, without taking notice of parameter interactional effect. For example, Luo et al. (2004) proposed a pressure drop number to distinguish separation performance without considering the bed height and gas velocity, which are intimately related to this proposed pressure drop number."

Jan 1, 2015

Never known as a conference to shy away from its share of off-color jokes, the Colorado Mineral Processing Division?s Annual Meeting returned to the Broadmoor Hotel in Colorado Springs, CO April 26-28 for its 62nd edition, this one held under the theme ?Does size matter (is bigger always better).? With the predictable jokes sprinkled in here and there, and a few unpredictable ones as well, the three-day conference featured a healthy mix of talks about some of the latest technical developments in the field of mineral processing, as well as insightful looks at some new operations in the western United States. This year, the Colorado MPD also launched the Wagner Equipment Student Scholarship program.

Jan 1, 2012

By Steven M. Puricelli

In recent times, smelter off gases treatment plants have become more efficient and environmentally friendly. Where in the past it was acceptable to process only high strength, treatable furnace gases, new smelters must now treat primary gases and abate dust and SO2 from secondary gases: Processing smelter gases can present some interesting challenges. Some equipment can see varying concentrations of sulfuric acid, up to the boiling point, with a periodic table of contaminates thrown in for good measure. Treating weaker secondary gases have, in the past, been cost prohibitive. Nowadays, new technology, like physical absorption or catalytic carbon, show promise for economically treating low strength secondary gases. Modem smelters do a much better job of treating the SO2 laden gases generated by the smelting process but significant challenges remain.

Jan 1, 1998

By P K. Kaiser, D A. Malovichko

Highly stressed excavations in hard brittle rock may fail by self-initiated, triggered or dynamically loaded strainbursts (Moss and Kaiser 2021). The low-frequency part of seismic radiation associated with strainbursts is described by a crush-type seismic source mechanism with a significant negative (implosive) isotropic component and a ‘pancake-shape’ CLVD deviatoric component. The seismic source is co-located with the excavation damage site. For such strainbursts, the ejection velocity is primarily related to the depth of strainbursting, the rock mass bulking characteristics, the duration of the bulking process, and the effectiveness of the support system. For dynamically loaded strainbursts, the displacement and energy demand may be augmented by the impact of the stress wave from a distant seismic event. This article describes the failure process and factors contributing to rock deformation and energy demands for support design. Case examples are used to demonstrate the dependence of rock displacements, rock ejection and energy demand on the factors described above. A seismic source model is proposed to assess the depth of strainbursting and the duration of the related bulking process by using seismic monitoring data. The implications for support design are briefly discussed.

Apr 26, 2022

By Yi Luo

Bolting the mine roof is one of the noisiest underground mining operations. The main contribution to the noise is the drilling of the roof bolt holes, especially drilling in hard rock. Previous research shows that the specific energy consumed in drilling bolt holes is inversely proportional to the bite depth (i.e., penetration per drill revolution). Less specific energy at a reasonably high bite depth means less energy is wasted in the drilling process for producing heat, bit wear and noise. Therefore, proper control of the drilling operation to achieve a reasonably higher bite depth can reduce drilling noise from its sources as a proactive noise control approach. In order to explore the feasibility and develop the proactive technology for reducing drilling noise, drilling tests have been conducted in laboratory settings. The preliminary results show that significant reduction in noise dose can be achieved by drilling in medium hard rock with uniaxial compressive strength of about 276 bars (4,000 psi) and at a reasonably high bite depth of about 4.6 mm/rev (0.18 in./rev). This paper presents the findings from laboratory experimental studies.

By A. D. Davis, C. J. Webb, C. S. Johnson

The Belle Eldridge Mine is an inactive lead-zinc mine in Spruce Gulch south of Deadwood, South Dakota. Acidic mine drainage (AMD) produced at the site drains into Spruce Creek, a tributary of Whitewood Creek. The site is on U.S. Bureau of Land Management (BLM) property. Extensive fieldwork was done at the Belle Eldridge Mine through the cooperation of the BLM and the South Dakota School of Mines and Technology. The site was extensively mapped to identify physical and environmental hazards such as tailings, waste rock, collapsed buildings, adits and workings. An exhaustive search of the historical records of the Belle Eldridge Mine was conducted. Maps of the under-ground workings of the Belle Eldridge dating from the 1930’s and 1940’s were found. The maps were used to correlate currently collapsed features to old adits and tunnels. Using hand corers and a portable drill rig, waste rock, tailings and soil core samples were collected and depth to bedrock was determined and the total volume of waste and tailings pile were determined. Related work examined the hydrology of the site. The site is very complex hydrogeologically. Numerous underground and surface workings and tunnels add to the complexity. Several seeps are located at the site, one of which is producing AMD. Recharge to the site was studied, and a 100-year flood plain map was produced.

Jan 1, 2000

By D. R. Dolinar

The fall of small pieces of rock between roof bolts causes over 80 pct of the ground fall injuries in underground coal mines. Roof screen, if installed on the bolting cycle, can significantly reduce the number of these injuries. As the surface of the roof fails, the screen will have to retain the broken rock without failing or excessive deformation. Welded wire screen is the most common type of screen material used for roof surface control in underground coal mines. The load-deformation characteristics and the load capacity of welded wire screen were evaluated in the laboratory in a specially built test frame. In the frame, the square screen sections were held in place by bolts and bearing plates at the four corners while a center load was applied to the screen. The parameters evaluated included the wire gauge and configuration, the bearing plate loads and bolt spacing. The wire gauge of the tested screen was 4, 6, 8, 9 and 10. Maximum screen capacities for both load and displacement were developed for each of the wire gauge sizes along with the screen stiffness. This information can be used for screen selection and for the evaluation and determination of screen performance. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By A. Redman

Aquatic organisms are sensitive to free cyanide (HCN) though the presence of certain metals that can form stable complexes and thereby reducing both the amount of bioavailable cyanide. Recent work has suggested that consideration of HCN rather than total cyanide can provide the basis for water quality criteria. Cyanide is often present in complex effluents that affect speciation and bioavailability. We have developed a model to predict the speciation of cyanide in complex effluents and have shown that this model can predict the toxicity of metal-cyanide complexes in terms of HCN. This study evaluated available cyanide toxicity exposures with this model to assess the role of water chemistry (e.g., metal-cyanide interactions) on the observed. Toxicity endpoints based on total cyanide ranged over several orders of magnitude for a variety of metal-cyanide mixtures. However, predicted HCN concentrations among these same tests described the observed toxicity data to within a factor of 2. Aquatic toxicity can be well described using HCN though in certain metal-cyanide mixtures toxicity was jointly described by HCN and elevated levels of bioavailable metals. This work was performed in support of an industry-sponsored reassessment (Gensemer et al 2006) of the U.S. EPA water quality criteria for cyanide (EPA 1985) using free cyanide as the basis for the re-calculation. The work presented in this manuscript presents technical support for using free cyanide as the preferred basis for this recalculation.

Jan 1, 2011

By M. J. Hannan

Considerable interest has arisen in developing analytical methods suitable for measuring resource commodity substitution patterns. some of this work has applied the Translog method to estimate actual elasticities of substitution. Recent examples incl.uae Privolos and Dunietz (1987), Kopp and Smith (1983), and Moroney and Trapani (1983). Another method, one which has received attention earlier in the work of Fisher and Pry (1970), is that of the logistic or diffusion function. We believe that the latter method has properties suitable for analyzing current problems of material substitution. The present study thus evaluates this method in its original logistic form as well as an extended version incorporating additional explanatory influences. The analysis is applied to copper/aluminum substitution and iron ore beneficiation. Substitution for copper by aluminum is examined in the building wire and cable, and magnet wire end-use markets. For iron ore, the substitution of pellets for sinter is considered for the U. S. market.

Jan 1, 1990

By R. L. Virta

Sixteen companies mined fuller’s earth in 11 states during 2004. Production during 2004, based on a preliminary survey of fuller’s earth producers, was 3.96 Mt (4.3million st) valued at $340 million. This compared with3.6 Mt (3.9 million st) during 2003, valued at $346 million. The 3.96 Mt (4.3 million st) probably includes some crude clay tonnage. And production of finished product probably was closer to 3.2 Mt (3.5 million st) in 2004. Georgia was the leading producer state of attapulgite-type fuller’s earth, followed by Florida. Georgia also was the leading producer state for montmorillonite-type fuller’s earth. It was followed, in descending order, by Mississippi, Missouri, Florida, Virginia, Illinois, California, Tennessee, Kansas and Texas.

Jan 1, 2005