Search Documents

By K. Severin, B. Flanigan, P. Marion

“Plutonic-related” gold deposits in Interior and SW Alaska (Tintina Gold Belt) vary significantly in size, grade, vein/deposit morphology, depth of emplacement, distance from causative pluton and metal association. Metal associations such as Au-Bi and Au-As-(Sb-Hg) are a good empirical indicator of depth of emplacement and distance from causative pluton and have been used successfully in exploration. Results from a variety of analytical techniques also suggest a phenomenological cause for these metal associations, e.g. gold and bismuth have linked metallogenesis at high temperatures and thus are best correlated at deposits that are deep and/or close to causative intrusions.

Jan 1, 2000

By E. R. Spencer

An assessment of U.S. western hard-rock miners? noise exposures was conducted as part of a multi-year National Institute for Occupational Safety and Health (NIOSH) survey of noise exposures in each sector of the mining industry. Noise from selected mining equipment and operator noise exposures were measured, analyzed, and tabulated for dissemination to the participating sites and are being used to direct NIOSH research and interventions to address the greatest noise hazards. Eighty-two noise dosimeter measurements were obtained, along with time-motion studies as the miners operated hard-rock mining machines. Ninety-six percent of the operators had daily noise doses that exceeded the Mine Safety and Health Administration?s permissible exposure level. The average gold miner dosages while operating the following equipment were: haul trucks - 261%, load-haul-dumps (LHDs) - 235%, single boom drills - 221%, bolters - 214%, and dual boom drills - 163%. The worst exposure level was a silver miner with a daily dose of 873%. Time-motion data showed that this miner?s exposure accumulated most rapidly while operating a jack-leg drill. These results will be used to help prioritize noise control development by NIOSH and other partners. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By G. W. Bonnell, D. A. Young, D. G. Genter

Through 1996 and 1997, CANMET and the Cape Breton Development Corporation (CBDC) conducted a project to study the Phalen Mine’s 7 East longwall ventilation network to help determine methane emission patterns that were having a negative impact on coal production. Increased methane emissions were primarily related to mining depth and were also affected by the influence of a large sandstone body located above the worked seam. The research included the installation of tube bundle systems to monitor waste (gob) methane and pressure differentials. The focus of this paper is on the novel use of tracer gas techniques that helped shed light on the performance of the ventilation system and in determining the methane migration paths in the waste.

Jan 1, 2001

By Alan Weakly

The Powder River Basin (PRB) of northeastern Wyoming and south-central Montana is the largest strippable reserve of compliant coal (0.6 or less lb of sulfur per million Btu) in the United States. In mining parlance, it is the Mother Lode! Wyoming’s portion of the Basin provides one fifth of the coal produced in the United States annually, and the state has been the nation’s top coal producer for the past six years. Based on 1993 production statistics and estimated strippable compliance coal reserves, Wyoming may remain the nation’s top producer for the next 76 plus years. Past articles on the PRB have focused mainly on production. After living and working in the Basin for the past five years, I have developed an appreciation for the area and its major industry that transcends size and production data. In the fall of 1993, MINING ENGINEERING’s publisher and I decided to present a series of articles that would cover many other aspects of the Basin. Ten topics were outlined, and specific individuals, selected for their knowledge and experience, were asked to contribute articles about their specialties. Although Montana has four large mines producing coal from the PRB, this series of articles will concentrate on the Wyoming portion of the Basin.

Jan 1, 1994

By Milan Yekich, Emanuele Cauda, Justin Patts, Cody Wolfe

A worker’s personal exposure to respirable dust in occupational environments has traditionally been monitored using established methodologies which entail the collection of an 8-hour representative sample that is sent away for laboratory analysis. While these methods are very accurate, they only provide information on the average exposure during a specific time period, generally a worker’s shift. The availability of relatively inexpensive aerosol sensors can allow researchers and practitioners to generate real-time data with unprecedented spatial and temporal granularity. Low-cost dust monitors (LCDM) were developed and marketed for air pollution monitoring and are mostly being used to help communities understand their local and even hyper-local air quality. Most of these integrated sensing packages cost less than $300 per unit, in contrast to wearable or area dust monitors specifically built for mining applications which have been around for decades but still average around $5,000 each. At the National Institute for Occupational Safety and Health (NIOSH), we are leveraging the power of high-volume data collection from networks of LCDM to establish baseline respirable hazard levels and to monitor for changes on a seasonal basis as well as following any application of control technologies. We have seen the effective use and advantages of monitoring live data before, during, and after events like shift changes, operational changes, ventilation upgrades, adverse weather events, and machine maintenance. However, many factors have prevented a systematic adoption of LCDMs for exposure monitoring: concern for their analytical performance, the complexity of use, and lack of understanding of their value are some factors. This contribution outlines a one-year case study at a mine in Wisconsin USA, covering the installation, maintenance, data visualizations, and collaboration between NIOSH researchers and the industrial hygiene professionals at the mine.

Feb 1, 2024

By S. I. Angadi, C. Eswaraiah, Sunil Kumar Tripathy, T. Santosh, Nilima Dash

Banded hematite quartzite (BHQ) and banded hematite jasper (BHJ) ores represent a promising potential iron ore resource in the near future. The hematite and quartz in BHQ and the hematite and jasper in BHJ are closely related and require fine grinding for the liberation of hematite phases. The present study investigates the mineralogical features and comminution properties of BHQ and BHJ ores. In the BHQ ore, it is observed that thick bands of hematite have fine inclusions of silicate minerals, whereas silica bands have few grains of iron-bearing minerals. The hematite and quartz minerals in the iron and silicate bands of the BHJ ore appear to be more intricately associated and complex in nature, presenting difficulties for liberation. Bond work index studies were carried out for the BHQ and BHJ ores with different product fineness in order to evaluate the energy requirements in fine grinding. A higher Bond work index value was found for the BHJ ore (15.4 kWh/ton) than for the BHQ ore (12.4 kWh/ton). A decrease in the product particle size was associated with an increase in the work index value. Single-particle breakage experiments were designed by varying feed particle size and input energy. The specific energy consumption for the BHJ ore was higher than that for the BHQ ore. The comminution parameters showed that the BHJ ore is harder to grind than the BHQ ore, which may be due to the mineral composition and association of hematite phases with the silicates.

By G. Aggistalis, N. Kazilis, C. Rawlings, N. Rachaniotis, S. Raptopoulos, M. Knights, R. Game

The Egnatia Odos (Odos meaning road) is one of Greece’s largest ever highway construction projects and one of Europe’s most important. The Highway will assist in the connection of the Greek Ionian/Adriatic Coast with Turkey and the Black Sea reviving an historic Roman alignment “Via Egnatia” connecting Rome to Constantinople (now Istanbul). There are 74 twin tunnels (60 bored and 14 cut-and-cover) with lengths ranging from 160 m (175 yd) to 4,600 m (5,031 yd) and 100 m (109 yd) to 270 m (295 yd),respectively. The complex geology and resulting physical geography have had a major influence on both the design and construction of these tunnels. This paper describes the management, design and construction challenges of these numerous tunnels.

Jan 1, 2005

By R. R. Kallu

The current 120 psi seal design and evaluation practices are mostly based on simple analytical solutions. Considering the simplistic assumptions and limitations involved in simple analytical solutions and practical difficulties involved in conducting conventional full-scale explosion tests for evaluating 120 psi seal designs, there is a need for developing new scientific methods and engineering practices for design, analysis and evaluation of mine seals.

Jan 1, 2010

By S. G. Mougiakakou

A computerized system (SCAPEVIEWER) based on landscape indices and artificial intelligence techniques is proposed in order to classify landscape images into various categories according to the quality of the pictured scenery. Photographs (totally 108) from various landscapes have been clustered, from seven experts in accordance to the mean estimation of landscape quality, into distinctive (C1), typical or common (C2), and indistinctive (C3). For each of the landscape photographs, ten (10) environmental and operational indices have been selected and determined, corresponding to visibility (V), naturalness (N), relief (R), flora quantity (FC), flora quality (F), water (W), skyline (SL), visual entities (G), season (S), and viewer position (P). These landscape indices are fed to a classifier. The classifier is a feed forward Neural Network (NN) trained by a novel hybrid method combining genetic algorithms and the back-propagation algorithm with adaptive learning rate and momentum. A total classification rate of 93.5% has been achieved, using only 8 input neurons. The discarded input neurons correspond to the indices S, and P. The pilot system SCAPEVIEVER has shown the feasibility of landscape photograph classification into three categories (C1, C2, and C3) according to the landscape quality, selecting simultaneously the most robust indices, by means of a computerized system combining the knowledge of an expert with a NN based classifier.

Jan 1, 2003

By J. Noll

There is a need for direct tailpipe sampling of diesel vehicles in mines in order to determine the effects of an emissions-based maintenance program, evaluate control technologies such as diesel particulate filters and identify the worst diesel particulate matter (DPM) emitters in a fleet of vehicles. therefore, this study examined the performance of three portable instruments: a personal dust monitor (PDM) manufactured by thermo Scientific, a prototype elemental carbon monitor (Airtec) manufactured by FLIr and a prototype Ae91 instrument from Magee Scientific. These instruments were evaluated on the basis of their ability to provide direct reading tailpipe analysis for DPM. It was determined that the average bias of the tailpipe results from the PDM and the Airtec were 3±12% and 4±20%, respectively, when compared to the standard method of determining tailpipe particulate concentrations from a diluted exhaust. It was also determined that the Ae91 instrument correlated with the standard method.

Oct 1, 2013

By Christopher J. Bise

PRINCIPLES OF MINE PLANNING During the initial planning stages, all mining operations are analyzed and evaluated in a similar fashion. This similarity holds true because the mine-planning procedure can be reduced to a network of interrelated systems that are tied together by a common philosophy of mine planning: namely, that the resource is to be extracted in a manner which is safe, efficient, and profitable. The success of the mining operation cannot be guaranteed unless each of these three requirements is met. Fig. 1 shows a flowchart for the initial planning of any mining operation. Notice that there is a preplanning stage that leads to the planning of four interrelated systems. The preplanning stage includes property exploration, estimation of production and manpower requirements, and the establishment of construction timetables. The four systems, evaluated after the pre-planning stage, are broken down into the following: (1) Excavation and handling system, (2) Strata control system, (3) Operating support system, and (4) Service support system. The Excavation and handling system includes the selection of all the equipment for the removal of the resource from its in-place deposit (e.g., draglines, continuous miners, rock drills, etc.) and for the transportation of the mined material from the face (e.g., belt conveyors, trucks, etc.). The Strata control system incorporates all those considerations which maintain the integrity of the roof, ribs, floor, and overburden both during and after the extraction phase; typical considerations in this area include pillar sizing, artificial support of the immediate roof in mine entries, and subsidence protection. The Operating support system contains the "necessary evils" of mine planning; the system consumes a large percentage of the mining engineer's planning time but does not contribute to the actual extraction of the resource. However, if proper attention is not paid to the various components of the system, such as ventilation, drainage, and power, then the mining operation will not perform to its capabilities. Finally, the Service support system is composed of those operations which keep the mine running efficiently; typical examples of these include maintenance and sup- ply. One important concept that Fig. 1 is designed to emphasize is that the four systems are interrelated; typically, a slight alteration of one can affect the performance of another. If these interrelationships are ignored, the effects on the system can be disastrous. The mine preplanning stage and the four subsequent system evaluations constitute the Analysis portion of the mine planning flowchart. After this portion of the study is completed, the overall projected operation can be evaluated by techniques such as financial analysis. This last step in the study is referred to as the Synthesis of the previously calculated parameters into an overall plan. Much has been written about the overall evaluation of mining properties, but, over the past thirty years, very little has been written about the analysis of mine- planning systems in a coordinated manner. Further, those texts which attempted this topic have failed to give sufficient examples for successful implementation, thus supporting the operating engineers' lament that it is easy to discuss theories but difficult to show applications. This text is intended to bridge this gap. Examples of the various stages of the analysis portion of the mine planning flowchart shown in Fig. 1 will be covered in this text, with the exception of the Service support system, since this system is oriented more toward day-to-day planning than long-term mine planning. INTERNATIONAL STANDARDIZATION The benefits that can be derived from an international standardization of the units used in mining engineering calculations are numerous. The interchange- ability of equipment parts and the ability to analyze and compare performance and design specifications on an equal basis are just two of the goals desired by both manufacturers and mine operators. Unfortunately, conversion to an international standard has not been rapidly achieved by engineers in the United States, due to their training under the English system. The Society of Mining Engineers of AIME has made the commitment for the adoption of the Systeme International d'Unites (SI) in all mining engineering calculations. Since many practicing mining engineers and students in undergraduate programs still find difficulty in relating to SI units, the calculations in this textbook will use the English system, with Table 1 available for conversion into SI units.

Jan 1, 1986

By Zephaniah Varley, Satoshi Akai, Richard Sage, Steve Redmond, Mike Murray, Rohit Shetty, Gerald Skalla

One would be hard pressed to find another project as complex as this one given its configuration, the variety of issues to address and the required construction techniques. Contract C710 is currently under construction as part of Sound Transit’s Link Light Rail, connecting downtown Seattle with Sea-Tac Airport. The paper describes the construction-to-date of the deep mined station under Beacon Hill using the Sequential Excavation Method (SEM). This deep “binocular” station is being mined through some of the most challenging soft ground conditions in the USA. The excavated volume of the station is approximately 60,000 cy (46,000 m3) and the station comprises a variety of geometries and cross sections ranging from 235 sf (22 m2) up to 1,670 sf (155 m2). This underground complex includes platform, concourse, cross-passage and emergency ventilation tunnels together with station egress and ventilation shafts. Various excavation sequences are in use for the different tunnels including the twin-sidewall drifts for the impressive45 ft (13.7 m) wide by 42 ft ( 12.8 m) high concourse cross adits. This station has two train platforms approximately 165 feet (50m) below the surface. This station, constructed in highly variable glacial deposits including water bearing sands and silts approximately 50 ft below multiple perched water tables in an urban setting, creates a very unique and challenging situation. The ground is being managed with various types of ground improvements such as jet grouting and vacuum assisted deep dewatering wells from the surface, and from underground by use of “SEM Tool-box Items” such as barrel vault canopy, grouted pipe and rebar spiling, chemical grout,

Jan 1, 2007

By L. B. Rothfeld

This paper presents preliminary results of a Bureau of Mines study of potential costs of compliance with the federal Resource Conservation and Recovery Act for copper heap and dump leaching. Specifically, estimates are given for the cost of compliance with possible technology standards that would require the use of liners and closure caps regardless of terrain and underlying geology and hydrology. This cost is compared to the co lit of compliance with present state requirements for terrain a typical of those found at existing copper leach sites in the Southwestern U.S.A. Incremental compliance costs are found to widely exceed screening criteria used by the Environmental Protection Agency to denote significant economic impact.

Jan 1, 1993

By Georgene Renner, William R. Yernberg, Steve Kral

ABB provides integrated pro-cess control, optimization and information systems, drives and power-distribution equipment as well as other services and support to the mining industry. ABB also supplies electrical equipment and control systems for the openpit mining industry. This includes products for the automation of electrical equipment in mine shovels. The company offers low- and medium-voltage drives for various mineral- industry applications. And ABB provides gearless mill drives for equipment, such as semiautogenous grinding mills that are too large for conventional drives. ABB Industrial IT provides innovative hardware and software systems that cover all the requirements of the modern mining and processing plant.

Jan 1, 2004

By S. E. Pérez-Fontes

An experimental study on the oxidation of chalcopyrite (CuFeS2), pyrite (FeS2), covellite (CuS) and chalcocite (Cu2S) particles was conducted by means of differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) techniques. The oxygen concentration in the process gas was set to 40% and 70% (by volume) and a heating rate of 40°C/min was used. Response variables included the temperature of incipient reaction, the total exothermic heat of reaction, particle mass, morphology and mineralogy of the reacted particles. Based on the experimental data and phase stability calculations, reaction mechanisms were proposed to represent the behavior of the particles during oxidation. The reaction mechanisms were verified by X-ray diffraction (XRD) analyses of the oxidized particles and by thermochemical and mass balance calculations to reproduce the DSC and TGA data. Overall kinetic models were developed to represent the evolution of the exothermic heat of reaction as a function of time.

Jan 1, 2007

By V. Svalbonas

Everybody has an opinion what the quality of a grinding mill head casting should be, yet extremely few take the time, or get the opportunity, to compare their opinions against fitness-for-purpose data. The real question is not how flawless the casting should/could be, but rather how long will ?this? casting survive in operation. To validate an opinion on this topic one needs either extensive historical data, or comprehensive experimental data, or preferably, a combination of both. The same data can also be used to establish the conservativeness, or lack thereof, of analytical prediction methods.

Jan 1, 2009

By L. C. Raymond

Good afternoon. I have entitled my talk "Investment for Progress," implying thereby a spark of friendly competition by private enterprise with such government-inspired foreign aid and investment programs as the Alliance for Progress. While the subject of foreign investment is hardly a new one, the perpetual flux of the political and economic surface of this earth we inhabit makes it forever timely and forever interesting. Especially do tremendous opportunities for international investment constantly present themselves to the mineral industry, and just as often must the industry approach these opportunities with a great deal of investigation and caution. This is not to say that the mineral industry--no less than any other industry--should be unenthusiastic about the foreign scene, but like everyone who proposes to put his money where his hope is, it should consider all the factors and weigh the possible disappointments as well as the rewards.

Jan 1, 1964

In 1991, Placer Dome Venezuela established a 70% stake in Minera Las Cristinas, to mine the Las Cristinas gold deposits in Bolivar. This case study examines the multi-sectoral partnership arrangement that was developed to improve health services near the proposed Las Cristinas gold mine. The investment climate in Venezuela is uncertain and the socio-economic circumstances are potentially hostile. Despite that, the partnership between the mining company, local communities, government agencies and an international health nongovernmental organization (NGO) collectively leveraged nearly $2.5 million to build and operate a community health center.

Jan 1, 2002

By Bengt L. Stillborg

INTRODUCTION This paper summarizes the result of a two and a half year research program. The objective of the research was to develop a fundamental understanding of the Rib-in-Roc method. Through the development of a new model technology, namely three-dimensional physical models which powerfully exploit the results of dimensional analysis Stillborg, Stephansson and Swan (1), it has been possible to establish the contribution to both permanent and immediate stabilization of a large underground opening pre-reinforced by the Rib-in-Roc method. Using the results from these physical models and earlier work by Stillborg and Stephansson (2) and Åkesson (3), a conceptual synthesis is given in this paper so demonstrating the Rib-in-Roc method to be a practical working system of pre-reinforcement. DESCRIPTION OF THE RIB-IN-ROC METHOD To give the reader an idea of how this method of pre-reinforcement is performed, a short description will be given, Figure 1. Before any full-scale excavation takes place an entry is made in the host rock and rib raises are driven around the proposed opening. These raises are made at a spacing that is dependent upon rock quality; an opening in poor rock needs more ribs per length of opening. As the ribs are driven they are used as a site from which very competent rock bolting can be done. As a rib is excavated it is filled with reinforced concrete. Finally after having in this way reinforced the zone around the proposed opening, (a reinforced arch is formed) the displacements are automatically controlled as the opening is being excavated. Using this method openings with a span of 50-60 meters (160-200 ft) and a height of 60-80 meters (200-260 ft) are likely to be realised.

Jan 1, 1979

By H. Walqui, C. Noriega

Southern Copper Corporation (SCC) is one of the world’s largest copper companies and is finishing the modernization of the Ilo copper smelter. A single ISASMELTTM furnace will start smelting 1,200,000 tons per year of concentrate at the end of 2006. Three existing Peirce Smith converters are being upgraded plus a new one for converting the matte to blister copper is being installed. Two new anode furnaces and a twin anode casting wheel have being operating since January 2006. This represents one of the main changes in the process because the final product of the smelter is now anode copper instead of blister copper. A new oxygen plant, acid plant, and others facilities are in the ramp-up stage. This environmental project will ensure that the new smelter will comply with the environmental regulations of Peru by the end of January 2007. This paper summarizes the background to the modernization project, describes the different stages of the project including engineering, procurement and construction, describes the main areas of the new copper smelter and also the pre-operational testing, commissioning and start-up of them. This is a brown field project with a target of reducing as much as possible the production losses of the existing operation. This paper presents the details of the development of the Ilo Smelter Modernization Project and explains the main aspects of the new facilities, the products to be obtained and the associated facilities for their commercialization, including a Marine Trestle for bulk acid exportation.

Jan 1, 2007