Search Documents

By A. M. Cummings

Each mining district presents different problems as to the methods of ore extraction cad underground support, which are dependent upon the type of the ore deposit and the character of the inclosing rock. Mining costs, however, depend largely aeon the efficiency with which the methods employed underground are [applie] as well as upon the selection of the method best adapted to the physical conditions. The purpose of this paper is to present to the operator in other districts a detailed description of ho mining method used ins results obtained in tie exploitation of the bedded magnetite deposits of the Mineville district. The town of Mineville is situated in the Adirondacks, five miles west of Port Henry on Lake Champlain.

Jan 1, 1928

By N. A. Eilertsen

The Aroostook manganese-bearing deposits lie within a rectangle 30 miles wide and 70 miles long. Over 40 different deposits have been discovered in this area, but they have not been mined because the ores are difficult to treat. In 1949, the Maple Mountain area was selected for detailed investigation by the Bureau of Mines, because study by the State of Maine and the Federal Geological Survey indicated that it was the most promising in Aroostook County for developing a large tonnage of reserves. Investigation by the Bureau of Mines disclosed that all of the reported deposits of the central district were located on the limbs of a syncline underlying a pear-shaped area of 283 acres between the crests of Maple Mountain and Hovey Mountain. The ore area has been outlined by trenching and drilling along three sides of the perimeter, while the remaining side is defined by a fault. The area has a length of 6,300 feet and a maximum width of 3,100 feet. Diamond-drill holes have intersected the deposit as deep as 1,550 feet below surface, but additional deep drilling would be required to determine the intensity of folding or warping at depth. The Maple Mountain-Hovey Mountain deposit lies in the slates of Ordovician age and is classified into three zones, of which the upper, averaging about 57 feet thick, is designated manganiferous purple and red slate. The central zone, also averaging about 57 feet thick and containing the highest manganese content, is manganiferous, banded hematite. The lower zone is manganiferous, interbedded hematitic and green slate with an average width of about 33 feet. Manganese minerals occur with hematite in all three units. Trenching on the northwestern slope of Hovey Mountain uncovered other disconnected deposits of manganiferous rocks of earlier age than the ore of the syncline. The general strike of these deposits, which range from 15 feet to 75 feet in thickness, is southwest a length of 5,000 feet. They dip steeply southeast. The ore of the syncline is predominantly deep, hematitic red, inclining to red-dish black, fine-grained, dense, and thinly laminated. It is hard and siliceous. Hematite has, in places, been altered to magnetite. Because of the fine-grained texture of the ore, the manganese-mineral constituents are difficult to determine. Of the manganese silicates present, braunite is the most readily identified. Manganese carbonates and oxides are found also.

Jan 1, 1952

By MINE SAFETY BOARD

RECOMMENDATIONS OF THE UNITED STATES BUREAU OF MINES ON CERTAIN QUESTIONS OF SAFETY AS OF FEBRUARY 3 , 1933

Jul 1, 1933

By Maureen M. Foss

Underground coal mining is hazardous due to changing geological conditions. One geophysical method showing promise for in-seam hazard detection is ground-penetrating radar (GPR). The Bureau of Mines recently completed preliminary studies to demonstrate the feasibility of using GPR for in-seam hazard detection. Investigations included air and coal tests for the purpose of checking equipment accuracy, coal penetration, and other factors such as the effects of receiver orientation. Further investigations involved using both a short pulse and a new prototype synthetic-pulse system to locate a clay vein in a coal seam using trans-illumination. Data were gathered on multiple travel paths, and a back projection processing technique was then used to create a tomographic image using the calculated velocities. A computer model of the same coal seam was subsequently processed using the same tomographic tech-nique, and the results were compared with those of the actual data. Analysis of the tomographic images shows the presence of the clay vein, although its boundaries are unclear due to the tomography method used. Results of these preliminary studies show that GPR is feasible for use in in-seam hazard detection and point the direction that future research should take. A need has been shown for research involving more sophisticated tomography techniques, transmission studies on thicker coal seams, and reflection studies using the synthetic-pulse system.

Jan 1, 1987

By George D. Dub

The Bureau of Mines, in connection with the investigations of war minerals it conducted, examined the graphite deposits of this country, studied the methods of mining and preparation used, and sought to devise more efficient methods for the preparation of domestic graphite, and to standardize the quality of the product. The graphite investigations covered three general phases, as follows: 1. An examination of the deposits in Alabama and other States, and a survey of the methods of mining and preparation used. In this connection methods of sampling and analysis were noted and experiments made to determine a standard method of sampling and a, rapid but accurate method of analysis. 2. Experimental work on the concentration and refining of domestic crucible graphite to improve the quality of the product and to lessen waste. 3. Experimental work in crucible manufacture to determine the properties of domestic flake and the maximum proportions that might be used without impairing the quality of the crucibles. This work was accompanied by photomicrographic study of crucible structure.

Jan 1, 1920

By C. A. Herbert

This paper sets forth the hazards of accumulations of explosive mixtures of methane and air due to inadequate ventilation, the causes of which are discussed as follows: 1. Lack of well-maintained air courses. 2. Air losses due to leaky stoppings, trap doors, and overcasts. 3. Faulty mining methods. 4. Poor supervision. A modified plan of room-and-pillar panel mine development is suggested, which, it is believed, will eliminate many off the hazards of gas accumulations inherent in the present method of mine development. It is also suggested that some water-proofing agent be used on the roof of permanent air-course entries in conjunction with roof bolting to eliminate the detrimental effect of the moisture-laden atmosphere during summer and thus prevent serious roof falls.

Jan 1, 1953

By D. B. Taliaferro, Thomas Jennings, C. M. Keithly

"INTRODUCTION This report describes the methods of development and operation and gives the results of controlled water injection into oil sands in Illinois. It is the third of a group relating to water-flooding operations in various States; previous reports have covered projects in Oklahome 5/ and Kansas.6/ Systmatic water flooding has been in progress, in these States, for more 10 years. In Illinois the Tide Water Associated Oil Co. has been injesting water into one or two wells on each of five leases in the Robinson Acknowledgments This study was made under the general supervision of R. A. Cattell, chief engineer, and H. C. Fowler, assistant chief engineer, Petroleum and Natural Gas Division, Bureau of Mines, Washington, D. C., and N. A. C. Smith, supervising engineer, Petroleum Experiment Station, Bureau of Mines, Bartlesville, Okla., and under the direct supervision of Ludwig Schmidt, senior petroleum engineer, Bureau of Mines, Bartlesville, Okla.The cooperation of the operators who are conducting water-flooding projects and who have made this report possible by furnishing data on their operations is gratefully acknowledged. The writers are grateful also to the following members of the Bureau of Mines for assistance in preparation and criticism of the manuscript: C. J. Wilhelm, Franklin, Pa.; and Gustav Wade, R. E. Heithecker, and Peter Grandone, Bartlesville, Okla. The illustrations were prepared by Helen Cramer, Petroleum Experiment Station, Bureau of Mines, Bartlesville, Okla."

Aug 1, 1944

By Michael T. Nigbor

This Bureau of Mines publication identifies the significant environmental issues associated with the potential development of strategic and critical minerals in the Stillwater Complex, MT. The Stillwater Complex contains deposits of Cr, platinum-group metals (PGM), and Ni. Issues that must be addressed prior to minerals development include the effects mining, milling, and smelting will have on the land, water, and air, and methods of minimizing the environmental impacts.

Jan 1, 1985

By E. R. Spencer, D. R. Babich, L. A. Alcorn, A. K. Smith

Noise is one of the most pervasive health hazards in mining. A compilation of Mine Safety and Health Administration (MSHA) noise survey data for fiscal year 1990 shows that approximately 40% of the total samples taken for longwall occupations exceeded the Permissible Exposure Limit (PEL) of 100% (Gigliotti et al., 1991). To effectively determine worker noise exposures on longwall coal mining systems, it is necessary to provide accurate baseline measurements for these mining systems. This research was designed to develop measurement methods and test procedures for identifying noise sources that are major contributors to the underground noise exposure of longwall coal mining system workers. The measurement system that was used to analyze the noise sources around a stageloader used stationary dosimeters in a documented repeatable pattern to record the sound pressure and dose levels. A time-motion study of the cutting cycle and stageloader operator’s work cycle was done to correlate the sound levels at measurement locations and the resulting operator’s daily dose with significant noise events. Results from the underground measurements show that the highest sound levels recorded were at the stageloader discharge segment and tailpiece controls, where sound levels remained about the same throughout the test.

By Oliver Bowles

The National Granite Commission at its annual meeting in Norfolk, Va., in January, 1930, passed a resolution requesting the Bureau of Mines to conduct an economic study of the granite industry. In with this request a preliminary review has been made of trends in the production and uses of block granite.. Some unfavorable conditions were thus brought to light, and certain suggestions regarding a more orderly and consistent growth in the industry are herein discussed. The results of the study are, presented in this report for the earnest consideration of. the industry, and comments are invited, not only on this report but as to future work that might be accomplished by the Bureau of Mines. The authors desire to acknowledge many helpful suggestions and comments from Paul M. Tyler of the Bureau of Mines and from Harris F. Sherman, secretary of the National Building Granite Quarries Association. Miss A. T. Coons of the Bureau of Mines rendered valuable assistance through her wide knowledge of granite statistics. The block granite industry has shown little expansion during recent years. While the value of the annual production has grown from about $14,000,000 in 1904 to nearly $25,000,000 in 1928, the increment in value is caused mainly by mounting prices rather than by increased production. Even granite for memorials shows a very small advance in production volume, although the value has increased from about $3,500,060 in 1904 to more than $11,000,000 in 1928, which is the most consistent growth of any branch of the industry. The value of building granite has fallen for a number of years much below the figure for 1904, and in 1928 was very little in advance of the value attained 24 years previously. The use of granite paving blocks and rubble has shown a gradual decline.

Jan 1, 1931

By R. August Heindl

A process for recovering manganese from open-hearth steel-plant slags was investigated. The proposed method of accomplishing this is indicated by the flow diagram in figure 1. Mixtures of open-hearth, steel-plant flush slags and limestone, so proportioned as to have molar [CaO -3P205] ratios of approximately 2, were fired at approximately 2,400° F. in an oxidizing atmosphere and then cooled slowly. This treatment produced a clinker consisting principally of two solid phases comprised of (1) various combinations of the oxides of manganese, iron, aluminum, and magnesium, probably in spinel complexes, and (2) a dicalcium silicate phase, which contains the phosphorus. Reduction of these clinkers with hydrogen or with gaseous mixtures containing CO, CH4, and other hydrocarbons at about 1,300° F. formed manganous oxide as well as varying amounts of ferrous oxide and iron. Carbon monoxide and mixtures of hydrogen and carbon monoxide effectively reduced the clinkers but also gave higher proportions of soluble iron when the manganese was extracted from the reduced clinkers by leaching at about 80° F. with ammonium carbonate solutions containing 26 to 28 percent ammonia and 15 to 26 percent carbon dioxide. It is believed that the manganese is in solution as an ammonia-manganese complex. Concentrations of about 90 grams of manganese per liter were obtained by batch countercurrent procedures. By distilling 50 percent of the ammonia, the ammonia-manganese complex was decomposed, and approximately 90 percent of the manganese was precipitated as the carbonate with the simultaneous precipitation of 15 to 30 percent of the iron, the larger amounts of iron precipitating in the continuous tests. The manganese-iron ratio in the product could be increased either by recycling more manganese from the distillation to the extraction or by aerating the liquor to purge it of iron before, rather than after, the distillation step. Calcination of the pelletized manganese carbonate in an oxidizing stmosphere at 2,000° F. or above gave a final product, Mn304, resistant to crushing and apparently possessing the other physical properties essential in a ferromanganese blast-furnace feed.

Jan 1, 1955

By R. L. Grant

[p(,ton~to'rs 'ar-IV uscG.. to explode 9crnli .... sible c}:plosivcs, dynamites, or other hiGh uxplosives. This ?,...!xplosion or detr)nation is brought about by th\.:J energy which i liberated as a cOl":"Lb' nation of concusBion and heat wl1en the ? detonator is fired. 'm Ot:18t? I'l(jrds~ liThe detonator is the key VI: ich unlocks the enerGY of a llgh? explosIve""? (8) :1/. Being sensitive nd latently dangerous, detonators ITl.ust lTIeet t\V0 primary requirerDentr: They must be ..;.afe to handle and IT. list? detonate' when (l,esired, the ... eby iIr.parting deton:l.tion to the explo8ivc cJ.1Cire-e.]

Jan 1, 1941

By Joseph A. Holmes

The investigations carried on at the fuel-testing plant of the United States Geological Survey at St. Louis in 1904-1907 included tests of the steaming and gas-producing qualities of many coals and of the possibilif3 of their improvement by briquetting, together with washing and coking tests and tests of some of the resulting coke in the cupola. These tests were part of a general inquiry into the manner of utilizing most efficiently each of the coals under investigation. The equipment used in the cupola tests of coke, the manner of conducting the tests, and the essential results have been described in publications of the Geological Survey," and only the more important conclusions to be drawn from the tests are mentioned in the following pages. The tests were made to show the fitness of the cokes for foundry purposes, but an incidentlll result was to show foundry men and the coke producers the advisability of studying the conditions of foundry practice. The present bulletin, published by the Bureau of Mines because the analyzing and testing of fuels have been transferred from the Gilological Survey to the Bureau of Mines, briefly reviews the status of the coke industry, some features of practice in the use of coke in the foundry, the probable happenings of a cupola heat, and the reasons for modifying charging practice so that a particular coke can be used to best advantage.

Jan 1, 1910

Coal research and related activities in 1964 by the Bureau of Mines resulted in many advances in the production, preparation, and utilization of this valuable natural resource. Mining research during the year was marked by work on hydraulic mining, coalbed degasification, mine drainage control, mine sealing, strip-mine rehabilitation, and quenching of mine-refuse fires. Bureau research continued to produce information leading to increased safety in underground mining. Such research included roof and rib control via bolting and bonding, pressure monitoring of coal and mine rock during mining operations, and development of safety devices for detecting conditions leading to roof falls. Other safety work was continued on methane detectors, coal-dust suppression, and mine ventilation equipment and techniques. Mine explosion and explosives research, mine equipment and materials, safety rule modernization, and safety education and training of mine workmen were continued. Coal storage and preparation work in 1964 ranged from freezeproofing of lignite for rail shipment, through washability studies of coals and washing equipment, to research on new ways to remove ash and sulfur from coal. Electric power production, which accounts for a major portion of the market for coal, received further study. Unique power generation systems, including coal-burning gas turbine and megnetohydrodynamic generators, were intensively investigated. Conventional power systems were improved through continuation of work on furnace performance, powerplant stack gas purification, and engineering and boiler water service.

Jan 1, 1965

By Andrew F. Conn

This report summarizes the results from the first year of an anticipated multiphase program to develop improved coal mining equipment which utilize the CAVIJET? cavitating water jet method. This laboratory parametric study demonstrated the advantages of cavitating jets over non­cavitating jets in cutting coal, by producing comparable slot depths at one-fifth of the operating pressure, at better than one-half of the spe­cific energy. These results suggest that CAVIJET-augmented mining devices can be developed with compact, low-pressure pumps. Thus, CAVIJET should be capable of operating with safer, lighter support equipment, while providing all of the advantages (reduction of dust and sparks, reduced damage to cutters) of conventional hydraulic mining methods.

Jan 1, 1976

By E. E. Maust

The present work is part of an ongoing Bureau of Mines effort to provide a better understanding of the fundamental phenomena involved in sulfide flotation, the role of oxygen in xanthate adsorption being one essential issue. Galena was chosen as the material around which to develop a conceptual model, partly because of its demonstrated oxygen sensitivity and partly because information on its properties and flotation behavior constitutes the largest part of the fundamental information available on sulfides of commercial importance. The model is formulated primarily in terms of surface electronic energy levels produced by oxygen and xanthate and is further developed using existing experimental evidence and its implications. Four major functions of oxygen are elucidated, and the relationship of these to the formation of lead xanthate, dixanthogen, and a surface compound is discussed. Though yet incomplete, the model provides a useful framework within which the results of diverse experiments can be related to one another in their proper perspective, as shown by a brief discussion and resolution of some apparently discordant results reported in the literature.

Jan 1, 1976

By W. W. Adams

The accident-prevention record of the coal-mining industry in the United States was more favorable in 1936 than in 1935, both from the standpoint of the relative safety of the individual miner on the job and of the price in life and limb that the Nation paid for its year's supply of coal. The increase in relative safety of the individual miner was indicated by a lower death rate and a lower injury rate than in the preceding year per million man-hours of exposure to the hazards of mining; that is, per million hours of work performed by the employees. (See table 1.) A reduction in the price in life and limb that the Nation paid for a year's supply of coal was indicated by a smaller death rate and a smaller injury rate per million tons of coal produced. Thus the individual miner was a better insurance risk, as far as accidents were concerned, in 1936 than in 1935, and a ton of coal used in the homes and industries of the country represented less human suffering than in 1935. The two points of view are distinct, and both should be kept in mind when considering accidents and safety in coal mining or in other industries. More men were employed in 1936 than in 1935, and more workdays were available for the individual miner. Large gains were also made in the total number of man-shifts and man-hours worked in the industry as a whole. In number of tons of coal mined, 1936 showed large gains over 1935. Moreover, the average output of coal per man-hour worked was higher in 1936 than in 1935. All of these gains were made without lengthening the average number of hours of work per man per day.

Jan 1, 1939

By R. Blickensderfer

Laboratory wear testing was conducted by the Bureau of Mines on a variety of typical wear-resistant alloys used in mining and mineral-processing equipment to establish their relative spalling and abrasion resistance. Test specimens in the form of 75-mm-diam balls were subjected to repeated impacts until they broke, spalled excessively, or received several hundred thousand impacts. Pin specimens removed from the balls were evaluated for high-load abrasive wear. The alloys in-cluded commercial forged steels, cast steels, manganese steels, and four types of white cast iron, with a range of heat treatments. The effects of hardness and microstructure on impact wear and abrasive wear are discussed. The data should help mine operators select the compositions and heat treatments that best suit service conditions.

Jan 1, 1985

By R. W. Michelson

The Bureau of Mines developed computerized mathematical models to estimate the economic availability of Mesabi Range taconite concentrates; these are a quality model, a cost model, and an economic availability model. The quality model evaluates metallurgical test data; the cost model determines iron unit cost from mining and processing cost data; and the economic availability model determines quantity from geologic and ore quality data. By correlating all of the physical resource quality factors and dimensional characteristics with the economic cost factors associated with producing iron ore pellets, these three models combine to establish a final relation between iron ore reserve quantities and iron unit cost.

Jan 1, 1970

By W. G. Park

Long-range projection of demand for domestic crude oil indicates a continued upward movement and accentuates the need for increasing the recovery from known crude-oil resources to supplement expected future discoveries. Consequently, the industry and Government have given special attention to the viscous or heavy-oil deposits because they offer the distinct possibility of large order increases in ultimate recovery. This report presents data pertaining to 150 heavy-oil reservoirs in Arkansas including oil characteristics of samples from 38 of these reservoirs. To January 1, 1967, about 600 million bbl of heavy oil has been recovered from the 150 reservoirs in 63 oilfields; however, about 4.5 billion bbl, or 88 pct, of oil remained in the ground. Of prime importance is that much of this heavy-oil resource is in reservoirs having characteristics considered favorable for thermal-recovery operations. Data for the thermal projects initiated [thus Ear are presented in individual field discussions. Also discussed is the t crude oil supply-demand situation in the State.

Jan 1, 1969