Search Documents

By Mark Svinkin

To save time for construction of coal pits, the contractor decided to combine erection of the tower pitheads with digging of skip shafts to the depth necessary for placing proper coal pit equipment. It was obvious that blasts used in shaft faces and lifting machines installed at a lower part of the pithead could excite vibrations of an upper part of the pithead with curing concrete. The contractor was concerned about vibrations of pithead concrete structures and the disturbance of freshly poured concrete in forms at a top of the pithead as a consequence of structure vibrations. The results of a study of the tower pithead structure vibrations from blasting and operating machinery, and effects of structural vibrations on curing concrete are presented. Structural vibrations were measured at the tower pitheads of two coal pits from twelve blasts. Records of horizontal and vertical displacements were superposition of harmonic low-frequency damped vibrations and sporadic high-frequency damped vibrations with a variable frequency. Low frequency vibrations attenuated during 8-13 s after the last delayed blast. Measured values of the natural frequencies of pithead horizontal vibrations coincided with the calculated frequencies of horizontal bend vibrations. An increase of a face depth from 18 to 50 m diminished 16 times horizontal bending vibration displacements of concrete structures. Measurements of vertical structural vibrations from blasting demonstrated increasing of vertical pithead displacements with the rising of structure elevations. This is evidence of the pithead longitudinal tension. The holes with charges were not properly condensed for one blast. As a result of incompact stemming, the blast substantially increased the energy of airborne pressure waves, which triggered natural vertical vibrations of the pithead with high displacements.

Jan 1, 2004

By Travis A. Davidson, Ralph E. Burnham, Cathy Aimone-Martin, J. Kelly Ratliff

Blasters face a long list of tasks to execute daily—from vehicle inspections to blast design and layout, hole loading and tie-in, securing the site, and finally, safely executing the blast. Good practices and, in most cases, regulations and requirements necessitate documenting their work, specifically their blast report. While some blasters use paper forms, others use electronic means to streamline the process. The authors have served as attorneys and expert witnesses in representing companies and individual blasters in numerous administrative and legal matters in which documentation of the blaster’s work was both critical and detrimental to the effectiveness of defending their work. This paper discusses in a case-study manner the authors' observations concerning good blast report format, specific observations around electronic and paper report completion, record-keeping, seismograph setup and recordkeeping, video and photo documentation, internal auditing, and other topics related to documenting the blast. The paper aims to serve as a discussion guide for blasters to improve their blast record-keeping process, develop better practices that effectively document their work, and allow them to defend their work should a claim arise concerning their operations.

Jan 21, 2025

By Grant Small, Deon Pieterse

Reactive ground conditions at an open pit manganese mine in the Northern Cape of South Africa resulted in an unexpected detonation.

Feb 1, 2020

By Mario Alvarez

Drilling with tricone drill bits is widely used in the mining industry with a direct impact on drilling safety and costs, however it can be challenging to implement a new supplier of tricone drill bits, choosing a new model of this accessory due to the normal variations of the rock mass or even due to the acquisition of new and modern drilling equipment for open pit blasting operations. This article identifies the most common mechanisms of failure in productive drill holes of tricone drill bits, both in open-pit coal and metal mines, in two South American countries. It also emphasizes the important issues that must be addressed for the optimization of the performance of these accessories, such as the correct identification of the rock mass, the drilling parameters, and the impact of autonomous drilling on new equipment with this technology. The article presents some of the successful actions to economically improve the performance of drill bits considering the close relationship in the field with the supplier's technical representatives and factory designers, as well as the commercial interrelationship between their respective business areas. The article concludes by discussing the future of tricone drill bit design development, its environmental management, and possible new advances in its manufacture.

Jan 21, 2025

By David Leidel

A revolution in hydrocarbon well completions within the last thirty years has enabled drillers to tap the resources of known gas plays in an economically viable manner and deliver to market natural gas supplies for industrial, transportation and domestic use without the importation of liquefied natural gas from verseas. An added benefit has been the convenient location of one of these gas plays, the Marcellus Shale, in the Northeastern states strategically close to a major natural gas market, namely the cities and towns of the New England and Mid-Atlantic states. As a sidelight, the development of the tight gas reservoirs and their subsequent production has created thousands of jobs in an otherwise lackluster economy.

Jan 1, 2014

By William R. Adamson

This paper describes some of the results of previously unpublished research studies conducted in underground operations in Chile and Australia, where cross-hole seismic measurement profiles were interpreted in terms of dynamic modulus. This work dates from a period between 1987 and 1990 and the Author suggests that 30 years on, applying modern day technology, instrumentation and modelling methods, more meaningful, practical and applicable results may be obtained.

Feb 1, 2020

By Steve Dillingham

Blasting crews, explosive product drivers, drillers, blasters, supervisors, and salespeople all arrive daily at customer blast sites in vehicles of every type whether passenger cars, pickup trucks, or bulk trucks. The majority of these vehicles are company owned and re p re s e n t a substantial investment and risk for the company. That may explain why the costs resulting from blasting incidents is often surpassed by those involving motor vehicle accidents.

Jan 1, 2003

By Travis A. Davidsavor, Charles Dowding, David A. Provost, Yonggang Gou

This paper compares measured blast induced strains on operating, full scale, buried pipelines with three similar past studies. The recently performed study represents realistic and modern pipeline blasting techniques combined with modern data acquisition. The evaluation compares measured PPV and strain, as well as calculated stress, at equivalent scaled distances.

Feb 1, 2020

By William Adamson

Precise and data driven methods of predicting and modelling blast induced vibration intensity are created and applied under field conditions on a routine basis today. These models are fed with controlled field measurements of vibration pulses generated by controlled charges under known geometric conditions. With such models blasting and geomechanical engineers can estimate vibration intensity at established critical points in mine bench geometry (surface mining) as well as within semi-permanent crown and rib pillars (in underground mining).Damage to bench walls and destabilization of large-scale geomechanical structures can be partially attributed to high intensity blast induced stresses on the rock mass and structures that define important features such as safety catch berms and haul roads. In the underground environment, weakening of critical pillars in block caving or Long Hole Open Stoping(LHOS) operations may lead to ore sterilisation. Blast vibration intensity can be linked with physical alteration in critical rock mass volumes within themine. Often the potential for vibration damage is estimated by the calculation of a critical value of vibration intensity, derived from a consideration of laboratory measured rock matrix properties. Efforts to confirm the accuracy of these estimates of critical vibration level include post blast excavation photography as well as the visual examination of rock mass, pre-and post-blast, using video camera observation of the walls of purpose drilled observation holes. These methods clearly indicate a change in fracture state due to the blast induced vibration, however further modelling of geomechanical stability will benefit if seismic measurement data can be interpreted in terms of geomechanically relevant strength parameters. This paper describes some of the results of previously unpublished research studies conducted in underground operations in Chile and Australia, where cross-hole seismic measurement profiles were interpreted in terms of dynamic modulus. This work dates from a period between 1987 and 1990 and the Author suggests that 30 years on, applying modern day technology, instrumentation and modelling methods, more meaningful, practical and applicable results may be obtained.

By Harry Thompson

In using explosives to blast stumps from the ground in order to prepare it for farming, it is comparatively easy to place the charge under a stump having a semitaproot or a lateral system of rooting by boring or digging a hole in the earth to a point under the center of resistance and deep enough to give the desired effect.1

Jan 1, 2015

By Hans-Peter Rossmanith

Fracture mechanics (Atkinson 1987, Broek 1988, Rossmanith 1978-2002, 1983, 1997, Kanninen & Popelar 1985) and wave propagation (Graf 1975, Rinehart 1975) form the main ingredients in the new electronic detonator based blasting technology. The full potential of using short delay initiation timing in bench and underground blasting can only be exploited if the underlying physical processes are properly understood. From a structural geology point of view, in many open pit mine operations, blasting is performed in incompetent and/or loose rock. Under such conditions the stress waves produced by blasting very quickly dissipate in the rock mass and often their energy cannot effectively be put to work. This contribution shows the effect of open and closed joints – and to some degree also faulting – on the blast wave field and shows the influence of structural geology on the blasting result. A simple engineering method which combines wave propagation and impact mechanics is developed in order to assist the non-scientifically trained blaster in understanding blasting in blocky rock formations. Extensive use will be made of the so-called Lagrange diagram which was introduced in detail in the author’s previous lecture at ISEE 2003 (Rossmanith 2003). This presentation can be considered a continuation of the 2003 presentation.

Jan 1, 2004

By Robert B. Hopler

Reefs, exposed rocks, and fast currents made the Hell Gate section of New York's East River a treacherous passage ever since man attempted to sail through the area. As the harbor's importance grew, attempts to improve the channel were made, starting in 1851. This paper discusses the first major organized effort to clear the area, which began in 1869 and culminated in a single large blast in September 1876.

Jan 1, 1981

By Joshua Hoffman, Braden Lusk, Kyle Perry

Shock tubes are used to simulate large-scale arena explosions without the use of full-scale arena sites that utilize large quantities of explosives. Instead, small explosive charges can be used to drive shock tubes. When this is done, the geometries of the explosive charges can alter the resulting pressure time curve. A common geometry chosen for the explosive charge is a sphere in order to be congruent with the spherical shockwave that emanates symmetrically in three dimensions from the detonation point. This paper reports on the findings from experiments that study the effects of altering the charge geometries and explosive types while keeping the TNT equivalency constant. Peak pressures and durations were affected by these changes. Directional phenomena are exaggerated by the use of certain charge shapes and detonation points. The speed of the detonation front in the explosive being greater than the speed of the shockwave in air played a critical role in the resulting pressure time waveforms. Waveform manipulation can be used to generate job specific waveforms that ultimately benefit the shock tube operators and their clients.

Jan 1, 2010

By Braden Lusk

Vibrations as a result of blasting practices in mining engineering are a complex phenomenon controlled by many variables. Mine blast vibration modeling and prediction is becoming more important as a consequence of interactions by mining activity with an ever closer public. Many communities (all over the world) close to mining activity often complain about airblast and vibrations produced from blasting activity. It is important for the mining industry to have tools and understandable methodologies to model and predict blast vibration. These tools can then be used to predict and control vibration at neighboring structures.

Jan 1, 2013

By R. Ticona, J. Alarcon

In the continuous search to provide comprehensive solutions and identify opportunities to improve ore traceability, from the blastholes to mill feed, different ore traceability systems have been developed, which allow tracking the ore and associating its geometallurgical characterization of different sectors of interest from blasting to the processing plant, facilitating decision making and operational actions when detected during each stage of the plant. With the objective of improving the ore tracking from the mine to the processing plant in a Peruvian copper mine operation, the impact on the processing plant was evaluated in relation to blasting optimizations through a tracker system, relating the processes performance of the whole production chain with the geotechnical and geometallurgical properties ores in real time in the process plant: detecting when it was feed waste, high grade ore, low grade ore and ore with arsenic, among others. Unit and integral tests were carried out over a period of three months, with an implementation of tracker detection portals in the processing plant, which allowed to verify the proper communication of data and the web platform. The tests were focused on several blasts where the ore was in contact with waste and it were directly sent to the plant, with a classification by type of grade (high, medium, and low grade), type of material (ore-waste contour), this stage allowed to make operational adjustments in the field and in the mining operation. Finally, in the economic results, the special tests had 1000 trackers, obtaining for this project a sensitization of a cost benefit for the test stage, for the reduction of 50% of the waste material feed has crushed, with an estimated benefit of 1,987,646 USD.

Jan 1, 2024

By D. Fry, S. Hunsaker

Ammonium nitrate in explosives and sulfides in reactive ground have the potential to react at ambient and elevated temperatures resulting in premature detonations. The Australasian Explosives Industry Safety Group (AEISG) published, in 2006, a Code of Practice1 for elevated temperature and reactive ground. This paper reviews the chemistry, general reactivity of various ground types, elevated temperature hazards, and testing protocols contained in the code, that are industry best practices for managing ammonium nitrate-based explosives in elevated temperature and reactive ground conditions. In addition to reviewing the 5th edition AEISG Code of Practice, data is presented validating the recommended sampling guidelines within the code. Dyno Nobel has been screening reactive ground samples and performing sleep time testing since the code of practice was first released. Test results demonstrate the effects of samples that are allowed to oxidize before testing and are shown to be subsequently less reactive and not representative of the actual hazards facing mining blasting operations. Results also show that for a given reactive ground sample, reaction times decrease with increasing temperature. Data also quantify the delay in reaction time given by inhibited products. These results emphasize the importance of proper sampling and preparation of samples to accurately characterize elevated temperature and reactive ground hazards. They also demonstrate the efficacy of inhibited products in managing these hazards

Jan 1, 2024

By Jennifer Williams, Donald J. Berger

Originally built between 1913 and 1916, the Ashton Dam & Hydroelectric Facility has experienced various seepage and piping incidents since completion. Ashton Dam is located within 15 miles (24 km) of the historical Teton Dam failure site and about 2.3 miles (3.7 km) west of Ashton, Idaho. Numerous repairs conducted over the years ranged from filling sinkholes on the crest of the dam to placement of rockfill on the upstream slope to improve seismic stability. In addition, the existing low level outlet works was grouted full and abandoned in 1991 due to significant vibrations induced on the dam during its operation.

Jan 1, 2014

By Joshua Hoffman, Braden Lusk, David McLane, John Rathbun

The dynamics of explosive detonations are understood; however recreating a real-world, to-scale scenario is costly. The use of a shock-tunnel allows testing to be done on a smaller scale, with the simulated effect of a large explosion. Analyzing explosive waveforms using this method can greatly reduce cost in testing blast-resistant products, such as anti-terrorism devices, mine safety products, and military equipment. The purpose of this project is to better the understanding of how the waveform dynamics of an explosive detonated within a shock-tunnel differ from those in an open-air arena test.

Jan 1, 2011

By Paul Kunze

We have been told many times by legal folks and insurance types about the importance of producing accurate blast reports should you ever get dragged into court. In that venue the investigators will look at the information regarding product type and quantity, it’s distribution among the holes, and delay information in order to arrive at some judgement regarding vibrations or other blast induced phenomena

Jan 1, 2003

By Jeff Dean

As the Society celebrates its 35th year as an explosives industry association, it is clear that we are part of an industry that covers many sectors of economic activity. We are the voice of those who use, transport, store, manufacture, and dispose of commercial explosives products and others that serve the end user of explosives products. Along with other associations in this industry, we have a combined membership of hundreds of companies and tens of thousands of individuals in the U.S. and around the globe.

Jan 1, 2010