Search Documents

By K. Mallikarjuna Rao

There are several methods available to estimate deflection and ultimate Capacity of laterally loaded piles. In this investigation an attempt has been made to verify the existing methods for prediction of ultimate lateral resistance and deflection with the laboratory and field test results reported in the literature. A 75 pile loading test data obtained from the literature was used to evaluate two methods designed to predict the ultimate lateral resistance of rigid piles and three methods designed to predict the lateral deflections of rigid piles and four methods designed to predict the lateral deflection of flexible piles subjected to lateral loads. The accuracy and precision of each method is quantified statistically. The statistical results of the overall analysis indicate that the mean values of the ratios of predicted to measured lateral capacities vary from 0.62 to 1.14 with an average of 0.88. However, the settlement predictions were much more widely scattered than the ultimate load predictions and in general all the methods have a tendency to under predict the deflections. A new method is proposed by modifying the Broms's method to estimate the lateral deflections of free headed rigid and flexible piles separately. The proposed modified methods were found to be reasonably good in comparison to existing methods and to overestimate deflections.

Jan 1, 1996

Case I- Timber Pile Test- 4 pages describe the pile driving record, the pile load test and the boring log. Case II- 24 inch square prestressed concrete pile-5 pages give details about the pile driving, the boring log, the pile driving record, and the pile load test. Case III- 12 inch square prestressed concrete pile- 5 pages describe the compilation of SPT blow counts for the whole project, the pile driving record, the pile load test and the detailed boring logs. The 70 foot long pile was driven by a Vulcan 08 pile hammer. Case IV- 12 BP 53 Steel H pile- 3 pages give the pile load test, the pile driving record and the nearest boring log. The 64 foot long pile has its tip at elevation 908 ft. and the ground is at elevation 972 ft. The contractor augered to elevation 959 ft. before driving the pile with a Conmaco 08 single acting pile hammer. The hammer had an 8000 pound ram, a rated energy of 26,000 ft-1b., and a 7 1/2 inch thick asbestos cushion. Dynamic measurements were made during driving of the test pile and measured a hammer energy equal to 12,500 foot-pounds.

Jan 1, 1988

By A. F. van Weele

In general cast-in place piles will have an irregular pile shape. However, it is possible that these irregularities are so large that they may lead to pile deficiencies. It is very rarely possible to examine the pile foundations visually. Also the performance of a static or dynamic load test on each individual pile is not practical and much too expensive. This is the reason why pile integrity tests have been developed: to reduce the risk of inadequate pile foundations by performing a simple test. Pile integrity tests are non destructive tests which are carried out after a pile has been installed. Over the years a number of techniques have been developed of which the most important techniques are briefly described in this paper. Of all pile integrity testing methods, Sonic Integrity Testing is the most widely used method in western Europe. This method has been developed by TNO some 15 years ago. Since then the method has been improved, largely due to advances in micro-processing. A major improvement was made by the introduction of digital signal processing techniques. This made the Sonic Integrity Testing method more accurate (smaller defects can be detected), faster (more than 200 piles can be tested on a single working-day) and more reliable (the results are easier to interprete). A few cases will be presented which will show the usefulness of the Sonic Integrity Testing method. In one of these cases, a helpful tool for interpretation of the results is explained: the Sonic Integrity Testing Simulation program TNOWAVE. Notwithstanding the fact that Sonic Integrity Testing is a powerful method, it has also some strict limitations. These will be discussed at the end of the paper.

Jan 1, 1987

By Gunhild Hennum, Tewodros Tefera, Gisle Håland, Annette Jahr

"Abstract The Gudrun field is located west of Stavanger in the North Sea at water depth of 109 m. A jacket substructure was selected to support the topside and was installed in 2011. The jacket shall be able to support 16 of 0.762 m (30 in) diameter conductors and is equipped with a drilling deck to allow for pre-drilling by a jack-up rig through the jacket. In general the soil conditions below mudline comprise of a thin top layer of very loose to dense sand overlaying several layers of sandy clay, ranging in stiffness from firm to hard. Below some 30 m depth the soil consists of layers of medium dense to dense silty sand overlaying very hard sandy clay containing thick beds of sand to 100 m depth or more below mudline. The jacket is secured to the seabed by twelve 2.438 m (96 in) diameter steel pipe piles, three at each pile cluster located at the four legs of the jacket at sea floor. Different design methods were used to determine the pile penetration depth. Pile drivability was evaluated using best estimate and upper bound soil parameters. The pile driving and blow count record show that the target penetration was reached as predicted. This paper discusses the different methods used to determine the pile capacity, target penetration depth and the drivability analyses made for the Gudrun jacket piles. The soil resistance during pile driving is back-calculated from the pile installation data and compared with the prediction made.IntroductionThe Gudrun platform is located west of Stavanger in the North Sea at water depth of 109 m. A jacket substructure was selected for the Gudrun platform. The general Gudrun platform jacket configuration is to a large extent dictated by the topside layout, the requirements for support points enclosing the well slots and access for the jack-up rig. The Gudrun platform jacket is a traditional 4 legged structure with a vertical side towards the jack-up rig. At the seabed the jacket is quadratic with a base dimension of 40 by 40 metres. Figure 1 shows the Gudrun jacket during load-out from the fabrication yard to the transport barge. At the site the jacket was lifted off the barge, upended and placed on the seabed by the installation vessel. The jacket is secured to the seabed by twelve 96"" (2.438 m) diameter steel pipe piles, three at each pile cluster located at the four legs of the jacket at sea floor. The target penetration of the piles is 47 m."

Jan 1, 2014

By Patrick J. Hannigan, Geir Veslegard, Frank Rausche, Rozbeh B. Moghaddam

A common type of deep foundation used in Norway to support bridge structures is the drilled pipe piles (piles) filled with concrete reinforcement after installation. The standard installation practice is the use of down-hole hammers. Complex geology and difficult subsoil conditions in Norway causes a high variability of soil and rock layers which in turn make for differences between actual subsurface conditions and those expected from geotechnical exploratory borings. This situation is strongly noted when the foundations are not fully socketed, and the rock layer is sloped. In this particular case, special testing procedures are required to assess the drilled pile base material and evaluate the rock-socket to ensure full contact between the foundation base and the rock surface. The local standard practice to verify the latter condition, consists of coring and visually evaluating the material recovered at the bottom of the drilled pile. This paper presents a case where the coring and visual inspection were not possible and alternatively the geological material encountered at the base of the deep foundations was evaluated using force-displacement measurements. Two 1016-mm (40in) diameter open-end drilled piles identified as P02-04 and P02-05 were tested and evaluated using in-situ force-displacement data prior to filling the piles with concrete. Test results showed an average displacement of 7mm (0.28in) corresponding to 35MPa (5.1ksi) stress level for P02-04, and 7.2mm (0.28in) corresponding to a stress level of 38MPa (5.5ksi). Based on testing results, both drilled piles were within the established material assessment criterion presented by the local authorities. INTRODUCTION This paper presents a case study in Norway where the material encountered at the base of an open- end drilled pipe pile (pile) was evaluated using force-displacement data. In the deep foundation industry in Norway, it is a common practice to install piles to support transportation structures. Once the piles reach the embedment elevation, and the pile base is assessed, these are filled with concrete. In projects where sloping rock is the supporting layer, and all nominal loads are supported by the pile base resistance, assessing the material encountered at the pile base to ensure full contact with the rock becomes critical. The local practice to make this assessment consists of the use of weighted tape, coring, or inspection cameras. However, similar to any other testing and evaluation methods, these come with their own limitations. The variability associated with the use of the weighted tape, accessibility for the coring equipment to complete a coring process, or the conditions at the foundation base such as murky water or thick drilling fluids could significantly impact the photo or video quality taken at the pile base. In such conditions, it is important to consider alternate testing methods to evaluate the material at the foundation base.

Jan 1, 2018

By R. Bellotti

The theory of cavity expansion in an infinite frictional soil mass whose strength is represented by a curved Mohr-Coulomb failure envelope has been used to predict with some confidence the cone resistance of a clean dry sand. Experimental data were obtained from cone penetration and pressuremeter tests on two sands, conducted in a large calibration chamber (CC) under carefully controlled placement and boundary conditions. A plane strain bearing capacity theory was developed, and to convert the results to axi-symmetric conditions, an empirical "shape factor" was used. In the paper, the theoretical background, experimental data, calculation procedure, and the results of the analysis are presented. In general, a reasonable validation of the cavity expansion approach to the bearing capacity of deep foundations has been obtained.

Jan 1, 1987

By Alain Pecker

The choice of a design concept for a bridge foundation is guided by various factors; several of these factors are indeed of technical origin, like the environmental conditions in a broad sense, but others non technical factors may also have a profound impact on the final design concept. The foundations solutions adopted for the Rion Antirion bridge are described and an attempt is made to pinpoint the major factors that have guided the final choices. The Rion Antirion bridge is exemplar in that respect: the foundation concept combines the simplicity of capacity design, the conceptual facility of construction and enhances the foundation safety. The design of these foundations was a very challenging task which required full cooperation and close interaction with all the parties involved: concessionaire, contractor, designers and design checker.

Jan 1, 2005

By S. Narasimha Rao

Significant amounts of lateral load may act on pile foundations supporting structures such as transmission line towers, tall structures, bridge abutments, offshore platforms, quay wails, harbour structures and anchorages for water front structures. There were several theoretical and experimental studies conducted on laterally loaded piles in clays to determine ultimate lateral capacity and deflections under working loads. Under a lateral load, a pile deflects in the direction of load application and the soil in front of the pile offers resistance to this movement. The ultimate lateral resistance of a pile can be estimated considering the statics of the pile for a known distribution of soil resistance with depth. In this paper, considering the contributions from both lateral shear drag and frontal passive earth pressure, a method has been proposed to estimate the ultimate lateral capacity of rigid piles in clays. The lateral shear drag has been estimated in terms of adhesion and shape factor. A few load tests were conducted on model piles subjected to lateral loading and these experimental values are used in verifying the proposed method. The reported results obtained from both model tests and field tests were used in support of the predictions made. In all the cases, there is a good agreement between the predicted and measured capacities.

Jan 1, 1996

By Clyde Baker

Drilled shafts for many situations offer an economical alternative to driven piles. The Federal Highway Administration (FHWA) has spent considerable time and money in research and developing design and construction guidelines for drilled shafts. However, the full potential of the technology may not be realized because of the uncertainty of the effects of construction on the actual service behavior and the lack of either reliable quality control tests to check for or evaluate defects, or inexpensive load test procedures. Static load testing is very expensive and it is not feasible to load test each shaft on a project. Therefore, other means are necessary to confirm or evaluate the integrity of the completed drilled shaft or to determine the capacity of the completed shaft.

Jan 1, 1989

By Sikko Doornbos

For the extension of the Paper Mill of Parenco in Renkum, the Netherlands, the application of a pile foundation was required. The demands for this pile foundation were very explicit a vibration free and soil displacing pile systems with low allowable settlement. Another important aspect was the total amount of piles (originally over 1600 auger piles) which had to be executed within 3 months, in very difficult and unhomogeneous soil. Based upon these conditions the Tubex Grout Injection Pile was chosen to be used for this project. This system involves the drilling of a steel tube with a conical pile shoe while grout is injected at the point simultaneously, creating a mixed-in-place layer around the tube. INTRODUCTION After extensive marketing, the board of directors of Parenco, decided to a large extension of the production capacity of its paper mill by building a new production building called Paper Mill 1 or PM-1. The new PM-1 extension had to be constructed beside the existing PM-2 because of limited terrain. The site is located right between the Rhine river and Renkum, approximately 15 kilometers (10 miles) west from Arnhem (see figure 1). The construction involved the building of the PM-1 extension of approximately 250 meters (820 ft.) long by 40-60 metres wide (130-200 ft.). The main structure was to be constructed of precast concrete beams and columns.

Jan 1, 1987

Precast prestressed concrete piles designed to be end-bearing in a sand stratum at Drax Power Station met with extremely variable resistance during driving. Some piles came to virtual refusal almost immediately on entering the sand whereas others were driven to considerable penetration with very low resistance. Redriving and load tests on piles experiencing low resistance on initial drive showed that take up in strength occurred over a relatively short period of time. Investigations involving the use of pneumatic piezometers revealed the development of significant excess pore pressures during driving. Samples from boreholes showed that piles met the least resistance when the sand had a high silt content. Comparison with the original site investigation data demonstrated the difficulties in predicting detailed pile behaviour. The varied behaviour could not be related to the original borehole logs or to SPT or static cone penetrometer results. The factors controlling pile driving behaviour were essentially geological and could only be explained with reference to local soil grading.

Jan 1, 1989

By Carlos Lam, Joram M. Amir, Erez I. Amir

"Abstract The modulus of elasticity of pile material (E) is an important parameter for the interpretation of both static and dynamic loading tests on piles. This value is commonly assumed to be constant with depth though it may not be true for deep bored piles due to the chosen casting method and/or selfweight consolidation. To provide evidence to support this proposition, the results of compressive strength tests on core samples taken from four different studies have been presented. The results show a marked increase in the strength and stiffness values with depth. The results of crosshole ultrasonic tests conducted at another site also confirm the same pattern. It is therefore recommended that before load testing a pile the distribution of the E values along the pile axis should be investigated. This will ensure the use of a realistic elastic modulus value and hence the correct interpretation of thedistribution between the shaft and end resistances.IntroductionThe modulus of elasticity of pile material (E) is an important parameter for the interpretation of both static and dynamic load tests on piles. Multiplying E by the strain measured by either strain gauges (e.g. ASTM D4945) or tell-tales (e.g. Geffen and Amir, 1971) gives the stresses acting at a given pile section. Typically, in the absence of better information, the value of E is derived from laboratory tests on concrete cubes or cylinder specimens taken on site and is assumed to be constant along the pile. While this may be correct for pre-fabricated concrete piles that are cast in horizontal molds, it may not be true for cast-in-place piles that are produced in the vertical position.There are at least two factors that may contribute to the change in concrete properties with depth in a bored pile. First, the casting methods may be by free fall in dry holes (e.g. Kiefer and Baker, 1994) or by using a tremie tube if support fluids are used. In the former case, the earlier batches reach the bottom of the pile bore at a higher velocity and are thus compacted under higher energy. Second, regardless of the casting method, the fresh concrete in the pile bore will always consolidate at least partially under its own self weight. The materials in the lower parts of the pile will therefore experience a higher consolidating pressure. This can reduce the pore volume and the water content in the wet concrete, thus changing the properties of the hardened concrete. Recent research by Justs et al. (2011) has shown that even a relatively small pressure can have a significant positive effect on concrete properties such as compressive strength and stiffness. However, the possible change of concrete properties with depth is commonly ignored by foundation engineers in the current design practice."

Jan 1, 2014

By Wen Songlin

This paper presents an experimental program to investigate the behavior of a pile with wings under horizontal loads in sand at laboratory. The work focused on evaluating the lateral resistance behavior and the geometric effect of wing board on the horizontal resistance. Based on the measured data and observed phenomenon, the following behaviors have been observed: 1) A pile with wings is not only a powerful means to improve the horizontal bearing capacity of a pile foundation but also economy and feasibility; 2) The horizontal bearing capacity of a pile with wings increases with increasing of it?s wing board?s area; 3) The pile lateral capacity is also influenced by the wing board?s geometric shape. Under a certain soil and pile condition, there is a critical embedment depth of the wing board, which will yield the maximum horizontal bearing capacity. It was further observed that when the displacement of the pile head increases, part of the horizontal bearing capacity of the pile is developed by the so-called shaft?s anti-pulling capacity.

Jan 1, 2007

By W. J. Grose

The Embankment Place office development over the platforms of Charing Cross Railway Station in London has presented many interesting and unusual problems to the engineers involved with the project. The main structure is supported on widely-spaced columns which penetrate the station platforms and underlying vaults, calling for high capacity foundations built in severely restricted spaces. Hand-dug underreamed piles were chosen. Whilst a conventional design approach was taken to size the piles, a detailed appraisal of ground movements was made to explore the effects of the new building loads on the existing foundations, not only beyond the site perimeter but also those amongst the new foundations. Before construction of the pile proper could take place, it was necessary to sink a caisson through the upper unstable and water-bearing soils. This being identified as a high-risk item, a full-scale trial was carried out prior to embarking on the main works. The twenty-one hand-dug piles were 2.5m diameter, over 30m deep and belled out to between 4.5m and 6.6m.

Jan 1, 1989

By Andrew Malinak, William Perkins

Seattle’s Elliott Bay Seawall protects the 1½ miles of downtown waterfront between South Washington and Broad streets. The seawall supports the urban waterfront and infrastructure, including the Alaskan Way Viaduct and Alaskan Way, access to historic waterfront piers, and numerous essential buried utilities. Most of the original seawall was constructed between 1916 and 1936 over soft/loose non-engineered fill, estuary, and beach deposits. The majority of the original seawall was a pile-supported timber relieving platform that extended up to 60 feet behind the face of the wall (Figure 1). With maximum spacing between the timber piles of 3 to 5 feet, a virtual forest of timber piles were driven for the original wall.

Jan 1, 2018

By K. Englehardt

J BERESFORD introduced the subject of the paper which is the use of polymeric slurries to support the sides of diaphragm wall and bored pile excavations during construction. In the opinion of the authors the use of a suitable polymeric fluid offers financial and technical advantages compared with traditional bentonite based slurries. Under quiescent conditions a support slurry must have the following properties. - sufficient viscosity to support the sides of the excavation, to prevent infiltration into soils and to hold loose soil particles in suspension. - when agitated it should thin quickly to assist pumping transfer and cleaning and allow free passage of the grab or drill. - viscosity should be low enough during concreting to facilitate placement but high enough to prevent contamination of the concrete.

Jan 1, 1991

By Scott C. Vollmer

This paper seeks to examine some of the technical factors influencing the deflection of Mechanically Stabilized Earth (MSE) retaining walls based on the authors' field observation of numerous structures. Excessive deflections can be unsightly and can be perceived as wall failure. Deflections can cause cracking or gapping of the facing units and general misalignment. Deflection of the reinforced backfill zone behind the wall face can result in settlement of the backfill zone and adjacent pavement cracking. Deflections can be the result of excessive movement external or internal to the reinforced soil structure. This paper only examines internal factors affecting wall deflections. External factors such as foundation settlement are not discussed.

Jan 1, 2003

By Timothy L. Roberts

For many years practicing geotechnical and structural engineers in Texas and Louisiana were reluctant to include augered cast-in-place (ACIP) piles as a viable deep foundation alternate. Three primary concerns were the lack of a final driving resistance to confirm adequate capacity, the inability to inspect ACIP piles prior to installation, and the fact that pile integrity is highly dependent on the skill of the ACIP pile contractor's field personnel. The Deep Foundations Institute (DFI) Committee on Augered Cast-In-Place Piles has responded to these quality control concerns by establishing standards of practice for ACIP pile installation and ACIP pile inspection. Regional areas of the country have different subsurface soil and rock conditions and many times this will influence local installation and inspection requirements. The best way structural and geotechnical engineers can address quality control concerns is to be familiar with the DFI standards of practice, to know the special requirements for a particular project site, and to incorporate them into a well-written ACIP pile specification. The purposes of this paper are to: 1) review the main fundamentals of a successful quality control program, 2) describe how these fundamentals can be applied to the installation of ACIP piles, and 3) add personal experiences from ACIP pile projects in Texas and Louisiana. Nondestructive test methods are frequently used as a quality control tool to evaluate questionable piles. An additional brief discussion of two nondestructive test methods is presented to complete the paper.

Jan 1, 1998

By Wesley Schmutzler

The Deep Mixing Method (DMM) was employed to raise and support the LPV (Lake Pontchartrain and Vicinity) -111 Levee in New Orleans. Even using innovative technologies, the tight schedule to achieve the 100 year elevation by June 1, 2011 was a daunting endeavor. The size and scope of DMM proposed for LPV-111 was on a scale never attempted outside of Japan. Over 1.65 million cubic yards of DMM was installed. LPV-111 is adjacent to the Bayou Sauvage Wildlife Refuge, which is the largest urban National Wildlife refuge in the United States. By utilizing DMM to control settlement and improve stability of the taller levee, side slopes were steepened from the conventional 1V:4H to 1V:2.85H, thus avoiding encroachment into the Bayou Sauvage and reducing the amount of clay needed for the completed levee. The COE utilized Early Contractor Involvement (ECI) for this contract. The ECI process allowed for input from the DMM contractor, TREVIICOS South, in order to optimize equipment resources and material requirements. This paper gives an overview of the extensive DMM requirements for LPV-111 and explains the benefits of the ECI process.

By G. R. Dasari

New Austrian Tunnelling Method (NATM) has been analysed by Finite Element method in two and three dimensions by Strain Dependant Modified Cam Clay (SDMCC) Model. The effects of construction sequence, stiffness of shotcrete and time dependency of shotcrete on surface settlement magnitude due to the NATM have been studied. Settlements obtained in 2D analysis, as expected, found to be more than the observations. The surface settlements obtained in 3D analysis found to be about 3 times less than equivalent plane strain analysis. This is due to mobilisation of soil strength around the tunnel face and soil-tunnel lining interaction. About 40% settlements occurred due to excavation of face at the monitor section and 60% after the excavation crossed monitor the section.

Jan 1, 1996