Search Documents

By H. T. Kennedy, S. G. Dardaganian, J. L. Clanton

This paper presents equilibrium ratios measured on oil and gas samples taken from the Kelly-Snyder field at the reservoir temperature of 128°F. From these data smoothed curves were constructed for the reservoir fluid up to the bubble-point, 1,874 psia. A material balance calculation, based on the use of equilibrium ratios instead of the usual solubility and shrinkage meayr~rements is made on the field and compared to the con\.entional method. DETERMINATION OF EQUILIBRIUM RATIOS The equilibrium ratios, or K values were obtained by recombining separator samples of oil and gas taken when the reservoir was above its bubble point, and thus represented the reservoir fluid before any change had occurred due to the evolution of gas. The well sampled had a gas-oil ratio of 617 cu ft of high pressure sepalator gas per barrel of separator oil. and a bottom-hole temperature of 128°F. Samples were brought to equilibrium by agitating for 24 hours in a thermostat, maintained at the proper temperature within 0.2ºF, mercury being added when necessary to maintain the pressure constant. Samples of oil and gas were then taken by constant pressure displacement, and analyzed by low temperature frac-tionation. Equilibrium ratios were determined at 128°F and 500, 800, 1,000 and 1,400 psig. At the latter pressure, there were indications that the gas samples were contaminated with small quantities of oil, and only data taken at the first three pressures were included in Fig. I. This figure has been extended to higher and lower pressures by the use of the Fluor charts for 3,000 psi convergence pressure, on which the experimental points fit well. MATERIAL BALANCE EQUATIONS The possible errors involved in conventional material balance equations have been analyzed by Muskat1. Where the errors occur in field measurements, or in obtaining effective averages from variables such as gas-oil ratio and pressure, they will evidently be involved in any attempt to estimate the content of the reservoir. On the other hand, substantial errors may be introduced in conventional material balance calculations by: (1) the neglect of the amount of oil dissolved in gas at high pressures and temperatures in the reservoir, but which condenses under separator conditions; (2) the assumption that the separation of oil and gas in the reservoir may be duplicated by a differential liberation in the

By B. D. Lichter

In a previous paper, Oelsen, Schuermann, and Hey-nertl pointed out the possibility of obtaining complete thermodynamic functions for alloy systems from calorimetric measurements alone. Specifically, if the heat content of a heterogeneous, multicomponent system is known as a function of temperature and composition, then it is possible to derive the heats, entropies, and free energies of formation of liquid phases and of solid intermediate phases of fixed composition. The authors present equations and graphical techniques applicable to eutectic systems and systems with intermediate phases without solid solubility at lower temperatures. eijering has considered possible extension of the treatment to systems with complete solid-state miscibility at lower temperatures; however, experimental difficulties practically restrict the method to systems with very limited miscibility in the solid state. The purpose of this note is to present an alternative derivation of the heats and entropies of formation of liquid phases and of solid intermediate phases from heat-content measurements alone. Fig. 1 shows three types of phase diagram to which the analysis may be applied. If the heat content is determined as a function of composition x, at temperature T, we have quite generally and the heat of mixing of the liquid is obtained directly from heat-content measurements. If the temperature T lies in a two-phase region (solid-liquid) then

Jan 1, 1967

By J. H. Brophy, M. H. Kamdar, J. Wulff

A constitutional diagram for the Ta-W-Re alloy system is presented. Rhenium dissolves in the complete range of solid solutions between tungsten and tantalum up to 48 wt pct in tantalum 'to about 30 wt pct in tungsten. Intermediate x and u phases only are found. X-ray diffraction and fluorescence, metallography and melting-point measurements were employed. THE constitution diagram of ternary alloys of tungsten, tantalum, and rhenium for temperatures above 1000°C is reported in this paper. Alloys in this system rich in tantalum and tungsten are of interest for high-temperature applications, and those rich in rhenium for electronic applications. No ternary phase diagram appears to be available in the literature. The three-component binary diagrams have been previously established1-3 and the present ternary data are consistent with these. EXPERIMENTAL TECHNIQUES Commercially pure tantalum (99.7 pct), rhenium (99.99 pet), and tungsten (99.9 or 99.95 pct) powders were purchased from Fansteel Metallurgical Corp., Chase Brass and Copper Co., and Fansteel or Westinghouse Electric Corp., respectively. These powders were pressed without binder and arc-melted under helium. The preparatory and analytical techniques employed were identical to those used for the Ta-Re system investigation carried out in this laboratory.324 These included X-ray diffraction and metallographic phase identification, X-ray fluorescent and wet chemical analyses, solidus determinations and heat treatments in a resistance-heated tantalum-filament vacuum furnace. For microstructural examinations standard mechanical polishing techniques were used through diamond laps. Polished speciments of all compositions were etched by swabbing with 4 parts HI?, 4 parts HNO3, and 1 part H20. Since the microstruc-tures of alloys containing one or two phases closely resembled their counterparts in the respective binary systems, typical examples are omitted in this presentation. In all the alloys examined, it was possible to observe the number of phases present. Particularly when there were small amounts of one phase involved, it was possible to identify it only by a combined conclusion based on X-ray diffraction, position of an alloy in a composition series, and the phase rule. A total of 100 different alloy compositions was arc-melted and studied in the as-cast condition metallographically and by X-ray diffraction. Specimens of each of these compositions were heat-treated at 2680, 2530, and 2020°C for 1, 2, and 4 hr, respectively. Those which were treated at 2020 were given a preliminary homogenization treatment at 2500°C for 1 hr. Specimens of 25 alloys were heat-treated at 1200o C for 168 hr. Solidus temperature measurements were made by the detection of incipient melting in eighteen alloy compositions. The metallographic and X-ray diffraction results are summarized in Table I. Graphically, this information appears in the isothermal plots of Figs. 2 and 3. Within the accuracy of the experimental methods, two such plots are sufficient to locate these data, since the results for 1200°C were similar to 2020 and those at 2530 resembled 2680

Jan 1, 1962

By A. W. Schlechten, W. J. Kroll

As this paper is written, the only method for the commercial production of lithium metal is by the fusion electrolysis of LiC1-KC1 mixtures, as first proposed by Gunkz.2 The details of the industrial process have not been made public hut Osborg8 stated that an efficiency of more than 90 pct is obtained with a lithium metal recovery above 95 pct and that the metal is 99.5 pct pure. Pletenev9 gave a power consumption of 66 kw-hr per kilogram of lithium metal produced with a salt consumption of 9 kg of LiCl and 0.4 kg of KCI. Pletenev's figures indicate a somewhat lower recovery than that given by Osborg. In a recent report on' German lithium plants, Motock7 gives figures that are also less favorable than those reported by Osborg. At the German plants the lithium recovery in electrolysis was only 83.4 pct, with a power consumption of 140 kw-hr per kilogram of lithium. The metal averaged only 97 pct pure, with sodium and potassium as the chief impurities. The presence of SO2, SO3, SiO2, Ba, Ca, and appreciable amounts of Na and Fe2O3 were especially disturbing in the electrolysis, and it was necessary to run the cell for some time to eliminate most of these impurities and condition the bath. It may be noted here that most of these impurities do not interfere with a thermal reduction process. These facts show that the present method of producing lithium is fairly efficient and would suggest that other methods could not compete. However, fusion electrolysis has certain drawbacks, such as the necessity of supplying costly, low-voltage direct current and of collecting and processing the anodic chlorine if it is not to be wasted. An even greater disadvantage is that lithium chloride must be used for an electrolyte. It is one of the most expensive salts of lithium, since it cannot be produced in anhydrous form by precipitation from aqueous solution, as is done with LiF or Li2CO3. The reduction of lithium by a vacuum process similar to the ferrosilicon method for the production of magnesium would have certain advantages. Small units such as Pidgeon retorts, would give flexibility of production to meet demand, and a small plant would require moderate capital outlay. There is a possibility of using idle Government-owned magnesium plants for such purposes. The raw materials needed for vacuum thermal reduction would not have to be extremely pure, Director, with respect to the iron and calcium Content. This paper describes a series of experiments to determine the effectiveness of various agents for the reduction of lithium compounds. The investigation is part of a program of vacuum metallurgy con-

Jan 1, 1949

By B. D. Cullity, A. Freda

It is well known that deformation by cold drawing or swaging produces a kind of preferred orientation called fiber texture in metal wires. Such textures have been extensively studied by means of X-ray diffraction, chiefly by techniques in which the diffracted X-rays are recorded photographically. This paper describes some results obtained with a new method, involving the use of a diffractometer. X-RAY METHOD Since the pole figure of a material having a fiber texture is symmetrical about the fiber axis, there is no need to present the entire pole figure. Instead, texture data can be summarized by means of a curve showing the variation of pole density along any meridian of the pole figure, if the north-south axis of the latter is made parallel to the fiber axis. The position of a pole on the meridian is specified by the angle 9 between the pole and the fiber axis (wire axis). The X-ray method1 used here to measure pole density as a function of 9 actually consists of two methods, referred to as A and B. In method a, X-rays are reflected from the wire surface. Pole densities can be measured by this method from O = 90 deg down to a limiting value which is dependent on the Bragg angle 8 and is typically of the order of 30 to 40 deg. Method B involves diffraction from the wire cross section and covers a range of 0 values from 0 up to an angle sufficient to overlap the measurements made by method A. By a combination of the two methods, a complete pole-density curve can be obtained. However, method A alone, which requires no specimen preparation other than etching, can often reveal enough of the pole-density curve to provide complete information about texture components. Both methods require that the measured diffracted intensities be corrected for changes in absorption and diffracting volume with changes in 9. A11 intensities I reported in this paper are corrected diffracted intensities; they are propor-

Jan 1, 1960

By Herty, C. H.

Present-day interest in the question of "dirty steel" has arisen primarily from the increasingly rigid specifications on various grades of steel and from the growing conviction that non-metallic inclusions are the source of many of the difficulties in meeting these specifications. The importance of inclusions has unquestionably been over-emphasized in many cases, but on the other hand many unpublished instances could be recorded where all evidence pointed to inclusions as the primary cause for the failure of steel in rolling or in service. The solution of the problem of dirty steel is not a matter of a few years. There are almost numberless types of inclusions. They segregate in steel ingots in an entirely different manner from other impurities, and, at best, only a start has been made in developing correct analytical methods for their determination. Most of the writers in the field have expressed opinions rather than given facts, and so many variables enter into the manufacture of steel that a study of plant conditions is difficult unless definite facts on certain phases of the inclusion problem are available. This statement is not intended to convey the idea that little work has been done on this problem. On the other hand, the number of investigations has been large, but in most cases too many variables have been present to allow definite conclusions to be drawn. In the body of the text, reference to previous investigations is made at suitable points. Rather than burden the reader with a lengthy review of the literature on the general subject of inclusions, reference to the particular works pertinent to the subject matter of the bulletin has been discussed. Three excellent bibliographies b on the subject have been lately published: one by the Committee on

Jan 1, 1957

By M. M. Singh, J. W. Brown

Three rocks of highly varied physical properties are selected for the first reported experimental study concerning microseismic activity of rock under tension to determine the effects of static fatigue, loading rate, repeated loading and rock anistropy compared to compression and bending loads. The microseismic method of detecting rock under deformation may be a great potential tool in surveillance and location in situ of dangerously stressed strata, as well as predicting rock failures. Noises emitted under load or the rate of energy (energy of noise pulses generated per unit time) are computed for varying conditions. The tests are conducted at constant load on a dead weight loading machine to eliminate all possible extraneous noises — an indispensable precaution — at various load levels. Experimental results are reported including the relation of total energy emitted to tensile strength of rock and the possibility of simulating a phenomenological model for microseismic activity. Plots of some of the experiments are included. INTRODUCTION Rock failure, whether on a large scale faulting in the earth's crust and rock bursts in mines, or on small scale ruptures of laboratory test specimens, generates transient vibrations in the rock mass. Mechanisms of intermittent deformation, such as twinning and cracking through and between mineral grains, also produce similar vibrations, but of very small amplitude. Such vibrations from both deformation and failure are referred to as microseismic activity, rock noise, or occasionally seismo-acoustical activity. An individual rock noise is sometimes

Jan 1, 1967

By Michael J. Messel

OF the various minerals that occur in fibrous form known as asbestos, chrysotile is the variety most in demand for commercial uses, and, last year, over 683,000 tons of the various grades were produced in Canada and United States, exclusive of African and Russian production, which figures are uncertain. Production has not been able to keep up with the increased demand, and an acute shortage exists. Canada, Russia, and Africa are still the most important producers. However, Russia consumes most of its production at home and exports very little. The United States consumes over 60 pct of the total production and produces only about 4 pct of the total from deposits in Vermont and small quantities from Arizona. This paper will review mainly, some of the more recent developments concerned with the extraction and processing of this fibrous mineral for various industrial uses, such as textiles, insulation, building materials and brake linings.

Jan 1, 1949

By J. van Lookeren

In the case of a reservoir where the oil underlies a large gas cap and overlies bottom water, production can be inzproved considerably if wells are perforated below the water-oil contact rather than opposite the oil-bearing section. The theoretical arguments for this improvement, which in some cases may be tenfold, are supported by experimental evidence. INTRODUCTION Reservoirs frequently consist of one sand body containing an oil layer underlying a thick, gas-bearing section and overlying bottom water (Fig. 1). Wells in such reservoirs are customarily opened up opposite the oil-bearing interval or, rather, opposite the lower part of this interval (Fig. 2). More often than not, it is inefficient or prohibited to blow off large quantities of gas with the oil. This im-psses a severe limitation on the drawdown, which results in low oil-production rates. Because of the small difference in specific gravity between oil and water, the latter will easily cone upwards, so that the production of water together with the oil is not prevented by this completion method. In such a situation wells should be opened deeper, in the originally water-bearing zone. The gas can be shut off by not perforating over the upper part of the interval (Fig. 3) or by a tubing hung close to the bottom of the interval (Fig. 4). Initially much water will be produced, but when steady-state conditions have been established (as depicted in Figs. 3 and 4) larger drawdowns are permissible than in a conventionally completed well, and correspondingly higher oil-production rates will result. Water cuts are only slightly higher because of the small effect of gravity on the water-oil flow distribution. CALCULATIONS The ratio of improvement has been estimated by means of approximate calculations. The completion depicted in Fig. 4 is the most convenient basis for these calculations. By postulating that vertical flow gradients can be disregarded, the Appendix shows that the well-known Dupuit formula can be obtained except for some complication due to the presence of two fluids rather than one. The Appendix makes the reasonable assumption that, for suitable boundary conditions, the oil layer occupies a constant fraction of the total fluid height throughout the reservoir. The oil- and water-production rates can thus be related to the liquid levels in the borehole as follows:

Jan 1, 1966

By Marcus Nadler

WAGES in the United States, in spite of the wage freeze, have increased materially. Overtime payments have become standard practice in almost all industries. Now efforts are being made to place wages on an annual basis, and if this is adopted, it will result in an increase in the cost of production. Organized labor today is more powerful than ever before; union membership is large and steadily increasing, and in many instances membership in the union is a prerequisite to employment. The treasuries of many unions are strong as a result of the large membership and full employment. The unions, therefore, today are in a much better position than ever before to carry on long strikes. Politically, too, the unions are more powerful today than they ever were. On the basis of their strength, one may expect that some of the demands that the labor unions will make in the not distant future will be granted. It is, therefore, quite evident that before long, particularly when the curtailment in war production reaches about 40 per cent, this country will be confronted with a serious labor problem.

Jan 1, 1945

By J. B. Clark

In 1933, R. paris1 published a phase diagram for the entire Mg-Ca-Zn system. He reported the existence of a ternary intermetallic phase, Mg5Zn5Ca2, which formed a quasi-binary with the magnesium solid solution. Since then, no extensive work has been reported on the system. Recently however, indications of the existence of a second ternary in-termetallic phase in equilibrium with the magnesium solid solution led to a reinvestigation of the solid phase equilibria involving the magnesium solid solution. The 335°C (635°F) isothermal section was chosen for study. Metallography and powder X-ray diffraction were selected as the best mutually corroborating methods for determining the solid phase constitution. Seventy-six alloys were prepared from singly sublimed (99.95 pct) magnesium, electrolytic (99.95 pct) zinc and USP calcium. The analyses of some of the alloys are shown in Fig. 1. The alloys were melted in a graphite crucible under a chloride flu and chill cast in a split graphite mold. Dif-fusion couples (see Fig. 2) were prepared by casting molten Mg-20 wt pct Zn alloy around a cylinder of Mg-30 wt pct Ca alloy. The alloy samples and the diffusion couples were sealed under argon in Pyrex vials and annealed in a furnace capable of controlling within 1/2°C of 335°C. At the conclusion of the anneal, the alloy samples were quenched in ice water and the diffusion couples were air cooled. Procedures standard for magnesium alloys were used for metallographic examination. Powder X-ray diffraction patterns were taken on a G. E. camera with a 14.32 cm dim using nickel-filtered copper radiation. The redetermined 335°C (635°) section of the Mg-Ca-Zn phase diagram is shown in Fig. 1. TWO ternary intermetallic phases, designated w and

Jan 1, 1962

By E. J. Dulis, A. Kasak, R. C. Westgren

The potential of uirought tungsten- and tantaluw-rich alloys of the W-Ta-Mo-Cb system was investigated for high-strength structural applications above 2500° F. Appreciable strengthening of tung-sten and tantalum—essentially attributable to solid-solzction effects—was obtained with binary, ternary, and quaternary alloys. Tensile strengths as high as 67,000 psi were achieved at 3000 OF. ThE quest for wrought structural materials which possess good strength properties at temperatures above 2000°F has led to a considerable research effort during the past decade. In addition to exploring the potential of various high-melting-point refractory metals (such as molybdenum, columbium, tantalum, and tungsten) for very high-temperature structural applications, alloy-development programs have been undertaken to achieve greater strengths than could be achieved with unalloyed refractory metals. The methods of strengthening refractory metal alloys have included both solid-solution and dispersion strengthening. General relationships among the relevant properties (melting point, recrystallization temperature, and high-temperature strength) of refractory metals indicate that the highest strengths at temperatures of 2500°F or higher would be obtained with tungsten-or tantalum-base alloys. Therefore, the present investigation was undertaken to determine the high-temperature strength potential of solid-solution strengthened alloys based on the binary system W-Ta; to effect further strengthening, minor additions of molybdenum and columbium (at the 6 and 12 pct levels) were made. The portion of the W-Ta-Mo-Cb quaternary alloy system of interest is shown schematically in Fig. 1. The component metals—W, Ta, Mo, and Cb—have a bcc structure at all temperatures, and their binary systems are mutually completely soluble.' Complete solid solubility in the W-Ta-Mo and W-Ta-Cb alloy systems has been demonstrated,' and, therefore, it was expected that the quarternary alloys of the system would also exhibit complete solid solubility at all temperatures. In the virtual absence of contamination by interstitial elements, all the alloys would be truly solid-solution strengthened. Twenty specific compositions of this investigation included binary, ternary, and quaternary alloys of the W-Ta-Mo-Cb system as well as unalloyed tungsten and tantalum. The compositions are shown in Table I. EXPERIMENTAL PROCEDURE Consumable-electrode vacuum-arc melting with ac power was used to produce small laboratory-sized, cylindrically shaped ingots (1-1/4 in. in diameter and 2 to 3-1/2 in. long) of the twenty compositions. A furnace was specially constructed to melt as many as four electrode rods simultaneously into molds lined with tungsten or tantalum sheet. High-purity rods of tungsten, tantalum, molybdenum, and columbium were used for consumable electrodes; the diameter of each rod was determined by the desired weight percentage of the component metal in a given alloy. The details of the construction and operation of the melting furnace will be discussed in another p~blication.

Jan 1, 1964

By H. Foster Bain

THERE has never been a great civilized nation which did not have a mining industry; civilization cannot flourish without metal mining. Without tools we can have none of the 'industries that are the foundation of civilization and without metal mining we cannot produce the material of which tools are made. Therefore, if we have no metal mining we have no metals, no tools, no civilization. An example to illustrate this may be drawn from a recent article in the Saturday Evening Post which described the run-down condition of modern Athens. Athens is nothing but a busted mining camp! In its palmy days the Greeks so applied the leasing system to the silver mines of Laurium that the royalties, paid the expenses of government and instead of a tax bill the inhabitants received a pay check. The Persians came over to capture these mines but the Greek navy was built to defend them. When the silver mines played out, Greek civilization declined.. Our mining must continue if our civilization is to continue.

Jan 1, 1921

By Robert G. Nisle

The classic theory of pressure build-up in shut-in oil wells as developed by Horner and van Everdingen is based on two-dimensional radial symmetry in the well-reservoir system. Such symmetry does not exist in the case of a well which parfiially penetrates the producing formation. As a result of this lack of symmetry the use of the classic theory in such cases become questionable. In this paper the mathematical theory has been extended to include the case of partially penetrating wells. Numerical solutions illustrating the up-dication of the equations are presented. The effect of partial penetration on pressure build-up is shown by a comparison of synthetic pressure build-up curves derived from the numerical solution of the equation for partially penetrating wells for various degrees of penetration. It is shown that partial penetration is detectable from the characteristic shape of the pressure build-up curve and that formation productivity may be calculated from the pressure buildup data in a manner identical to that described by the classic theory. INTRO DUCTION The use of pressure build-up data on shut-in oil wells is a well-established technique for the measurement of reservoir productivity. The work of Homer' and van Everdingen' is well known. Since the publication of their pioneering work, others"' have elaborated and extended the technique. These authors have dealt exclusively with the case of wells that completely penetrate he producing formation. Two-dimensional radial symmetry is achieved, thereby, and the problem is greatly simplified. This ideal situation is seldom encountered in practice. But, in spite of this, the technique is often employed anyway. The question, therefore, arises: how much confidence can be placed in the results of such calculations when the data are taken on wells that only partially penetrate the producing formation? It is the purpose of this work to answer this question. Only the single-phase fluid case will be considered. van Everdigen' has presented a rigorous solution of the two-dimensional case, but because of mathematical complexity, this solution has not proved to be particularly useful. Horner' utilized Kelvin's point source solution in two dimensions and showed that it is a sufficiently good approximation for oil reservoir studies. The geometry of the well and the producing formation is illustrated in Fig. l. Geometrically the formation may be described as an infinite slab. The infinite slab is defined as the solid (the porous medium in this case) bounded by two parallel planes. Thus, the slab extends to very great distances in both the positive and negative directions of two of the coordinate axes, but is finite in

By H. K. Najarian

AT Josephtown, Pa., on the south hank of the Ohio River about thirty miles northwest of Pittsburgh, is the Josephtown electrothermic zinc smelter, which operates as a custom smelter receiving both domestic and foreign concentrates. Constructed in 1930, the plant was designed to produce zinc oxide and to process 124 tons per day of zinc concentrate obtained mainly from the Company's New York State mines. Zinc condensing equipment was developed in conjunction with the St. Joe electrothermic. furnace and commercial production of zinc metal started in 1936. Expansion of the plant and equipment during 1939 and 1940 brought the processing. capacity to upwards of 300 tons of concentrate per day; and the plant operated at peak capacity during the war years, earning the Army-Navy "E" award and three subsequent stars. A postwar plant expansion is now under way, designed to increase the capacity to 500 tons per day of concentrate, with an estimated daily production of 160 tons of zinc metal of various grades, about 100 tons of zinc oxide, and 425 tons of sulphuric acid as major products.

Jan 1, 1947

By H.A. Bedworth

AlloTs of copper and silicon have been known for one hundred years or more but the commercial development of this type of alloy has taken place during the past few years. In 1905, Sperry l proposed the use of copper-silicon alloys for springs and other purposes for which copper-tin bronzes were used. Some attention was given to this proposal at the time but no one succeeded in producing a practical alloy containing more than a fraction of a per cent. of silicon. The equilibrium relations of the copper-silicon system were studied first by Rudolfi2 and later by Sanfourche 3 and Corson. 4 The constitution of the system has also been recently investigated by Matuyama, 5 and in the laboratories of the American Brass Co. by Smith. 6 Some of the physical properties of the copper-silicon alloys have been investigated by Norbury7 and by Geiss and Van Liempt.8 Summarizing the results of various investigators of the constitution of copper-silicon alloys, the solubility reaches its maximium value, 6.7 per cent. silicon, between 721" and '782" C. At 852" (1. the solubility is 5.25 per cent., while at 400" C. it is only 4.1 per cent. silicon. The copper-silicon alloy begins to get so hard at about 3 per cent, silicon that it is difficult to manage. It was found by Jacobs that the addition of manganese to this alloy considerably improved the working

Jan 1, 1929

By H. A. Bedworth

AlloTs of copper and silicon have been known for one hundred years or more but the commercial development of this type of alloy has taken place during the past few years. In 1905, Sperry l proposed the use of copper-silicon alloys for springs and other purposes for which copper-tin bronzes were used. Some attention was given to this proposal at the time but no one succeeded in producing a practical alloy containing more than a fraction of a per cent. of silicon. The equilibrium relations of the copper-silicon system were studied first by Rudolfi2 and later by Sanfourche 3 and Corson. 4 The constitution of the system has also been recently investigated by Matuyama, 5 and in the laboratories of the American Brass Co. by Smith. 6 Some of the physical properties of the copper-silicon alloys have been investigated by Norbury7 and by Geiss and Van Liempt.8 Summarizing the results of various investigators of the constitution of copper-silicon alloys, the solubility reaches its maximium value, 6.7 per cent. silicon, between 721" and '782" C. At 852" (1. the solubility is 5.25 per cent., while at 400" C. it is only 4.1 per cent. silicon. The copper-silicon alloy begins to get so hard at about 3 per cent, silicon that it is difficult to manage. It was found by Jacobs that the addition of manganese to this alloy considerably improved the working

Jan 1, 1929

By C. A. Meissner

THE following is a further discussion of the paper of James Gayley, " The Application of Dry-Air Blast to the Manufacture of Iron " (Trans., xxxv., 746), with special reference to his sup-plementary paper (Bi-Monthly Bulletin, No. 4, July, 1905, pp. 797 to 819), and. to the paper of J. E. Johnson, Jr., "Notes on the Physical Action of the Blast Furnace " (Bi-Monthly Bulletin, No. 5, September, 1905, pp. 1111 to 1146). Mr. Gayley's paper has been discussed also by E. Windsor Richards, R. W. Raymond, E. H. Saniter, W. J. Foster, H. M. Howe, V. Pendred, B. H. Thwaite, James Gayley and Alexander Pourcel (Trans., xxxv., pp. 1022 to 1042), Joseph W. Richards (Bi-Monthly Bulletin, No. 4, July, 1905, pp. 703 to 718); T. W. Robinson (Bi-Monthly Bulletin, No. 4, July, 1905, pp. 788 to 796) ; C. B. Dudley, R. W. Raymond, J. E. Johnson, Jr., W. F. Mattes, James Gayley, David Baker, John Birkinbine and F. E. Bachman (Bi-Monthly Bulletin, No. 5, September, 1905, pp. 1147 to 1152);.E. de Mille Campbell (Bi-Monthly Bulletin., No. 1, January, 1906, pp. 25 to 50) ; John Birkinbine (Bi-Monthly Bulletin, No. 1, January, 1906, pp. 137, 138). At the Washington meeting of the Institute, May, 1905, a very instructive and interesting paper was presented by Mr. J. E. Johnson, Jr., entitled " Notes on the Physical Action of the Blast Furnace,"' in which reference is made to Mr. Gayley's dry-blast process. A few of Mr. Johnson's conclusions, as summarized in the last pages of his paper, do not appear to me to be in complete accordance with the results obtained at the Isabella furnaces; and I therefore present the following notes which may throw further light on this subject: Mr. Gayley has called attention to the fact that the moisture in the air is an extremely variable and uncertain factor; and

May 1, 1906

By V. F. Parry, J. B. Goodman

The low-rank coals containing 10 to 50 pet natural bed moisture represent over half of the tonnage reserve of the available solid fuels of the United States, but only about 2 pet of United States coal production is derived from these fuels. Increased utilization of these large reserves will result if the bed moisture can be removed at the mine in high-speed low-cost processes. This paper presents a theoretical and experimental study of the factors affecting high-speed drying of coal dusts. The time required to heat particles of coal is proportional to the square of their diameter, and it is calculated that the probable time in minutes is equal to 6D2. In other words, a 11 a in. coal particle should be heated to drying temperature in 1.5 to 2.0 sec. Likewise, 1/8 in. particles should be heated in about 6 sec. The net heat required to dry subbituminous coal and lignite varies from 240 to 375 Btu per pound, depending upon the moisture removed, and this heat can be obtained from 42 to 61 cu ft of hot gases at 600°F.

Jan 1, 1949

By A. Raja, C. C. Harris

Apparatus for maintaining constant — but adjustable — pulp level and rate of froth removal are described. The results of preliminary experiments into the effect of scraping speed on the rate of solid and liquid recovery with a semi-batch system are presented. Glass spheres restricted to a narrow size range is the solid under investigation. Graphical methods for estimating the mass of recoverable material and the zero error are given. The semi-batch procedure1 is extensively used in laboratory flotation testing, though the method is subject to variability of moderate severity. Raffinot2 concluded from a statistical study of the difference between replicate tests, that the ptincipal source of errot was the test itself and not sampling or chemical analysis. These differences can be ascribed principally to changes in pulp volume and reagent concentration, and uncontrolled rate and depth of scraping. Semi-batch testing has been criticized1 on these grounds as a means of investigating flotation kinetics. This paper discusses and describes modifications to laboratory flotation equipment which reduce the number of manual operations and lead to improved control. Kinetic studies were the primary reason for developing the apparatus described. It should, however be a useful aid in normal flotation testing. Some preliminary results of experiments are presented.

Jan 1, 1967