Search Documents

By F. Benard

Recovery of selenium and tellurium at Copper Cliff by the Ontario Refining Co. has been previously described by the writer.l During 1935 a new building was erected to house this operation and description of the new plant and process form the subject of this paper. The building, of modern steel and tile construction, covers an area of 5900 sq. ft. with a volume of approximately 165,000 cu. ft. The large monitored center bay is flanked by two smaller outside bays, one of which is devoted to the tellurium section. All equipment, ceilings and upper walls, are treated with aluminum paint, giving good illumination and facilitating good housekeeping, essential from a health standpoint in handling material of this nature. Equipment Layout and type of equipment conforms to the requirements of the process as described below. In the selenium section, storage tanks, neutralizing tanks and precipitators are of steel construction, lead-lined and arranged for gravity flow (Fig. 1). The neutralizing tanks are equipped with water-cooled lead coils for controlling solution temperature, agitation being accomplished with compressed air. The precipitators are provided with mechanical agitators, and sulphur dioxide is introduced into the solution through 1/2-in. lead pipes leading from a manifold attached to the cover of the precipitator. Each precipitator has internal cooling coils and an air-jet exhauster to carry off fumes. Neutralized solutions are filtered in a 29-plate wooden filter press using heavy cotton duck as a filter medium, forced feed being maintained by a Welmet centrifugal pump. Dilute solutions are concentrated by evaporation in a vacuum evaporator, constructed of cast hard lead. Heat is supplied by an outside steam chest operating under 15 Ib. steam pressure. The solution is circulated through the steam chest by a pump of antimoniallead at a rate approximating 400 cu. ft. per min. The evaporator is evacuated by a water-jet condenser that creates a vacuum of 26 in. of mercury under normal operating conditions. The capacity of the vessel is 60 cu. ft. and the rate of evaporation 25 cu. ft. per hour.

Jan 1, 1944

By D. M. Wade, F. F. Redfield

PRODUCTION at Aguilar started in 1936 and by 1942 the mine had reached a peak of 25,000 tons a month. Present production is only about 60 per cent of this capacity because of difficulties in railroad transportation and the rationing of fuel oil brought about by the war. In the early years, cut-and-fill stopes were tried, but square sets were found to be the most practical method in the southern section of the mine, where blocky, treacherous ground and greater mining widths are prevalent. Square sets and opencut mining were the rule until 1942, when it became increasingly difficult to get mine timber. The ore beds in the northern section of the mine were found amenable to cut-and-fill stoping as the rock was firmer and the veins narrower. At present 69 per cent of the ore comes from cut-and-fill stopes, 27 per cent from opencut, and only 4 per cent from square-set stopes. Massive galena and sphalerite with comparatively little quartzitic gangue constitutes the higher-grade ore. The gangue minerals that can be detected by eye in low-grade ore are rhodonite, wollastonite, and pyrrhotite. Wall rocks range from shale to quartzite, with occasionally a little limestone.

Jan 1, 1947

By H. C. Heard

The review by Professor J. C. Jaeger (Chapter 1) briefly summarizes and discusses a select group of papers by various workers dealing primarily with aspects of fracture in brittle rock materials. Professor Jaeger's treatment is primarily concerned with the correlation of phenomenological and theoretical failure criteria with empirical results from short duration tests at ambient temperatures and generally at low lithostatic and interstitial fluid pressures. As engineering rock mechanics becomes more concerned with new techniques of mineral exploration and production at increasingly greater depths in the crust, it is well to be aware of the effect of the environment -that of the superposed stress field upon the lithostatic and interstitial fluid pressure, the temperature and the duration of the loading upon the failure of rocks either by fracture or flow. All results to be discussed here are from laboratory tests on small homogeneous samples, thus caution should be used in the direct extrapolation of these results to large inhomogeneous rock masses having quite different boundary conditions in the earth. The purpose of this supplement is to briefly point out the major effects of these parameters as examined singly, with all others held constant, and to cite some recent results which apply to the main theme on the brittle failure of rocks. The total stress field imposed upon a small volume of porous and permeable rock in the earth's crust may be thought of as the sum of an applied differential stress, plus a lithostatic pressure, plus an interstitial fluid pressure. The differential stress portion may be completely specified by nine components, six shear and three normal. If the small volume element is in rotational equilibrium, by suitably choosing our coordinate axes we may resolve these nine components into the three principal com-

Jan 1, 1967

By Walter O. Snelling

In the course of some experiments more than five years ago, made for a totally different purpose than the investigation of the oil used, I placed a small quantity of a transparent yellow lubricating oil in a bomb-like vessel and heated it to a relatively high temperature. At the end of the experiment I removed the oil from the vessel and was amazed to find that instead of bearing any resemblance to the oil which I had put in, it now had the appearance of ordinary crude oil. The green color by reflected light and the rich red-brown by transmitted light were so unmistakable as to at once lead to further investigation. I subjected the material to fractional distillation, and the surprise which I experienced at the appearance of the oil, changed to amazement when I found that it yielded, on distillation, 15 per cent. of gasoline and 30 per cent. of burning oil, and that its constitution resembled crude oil quite as much as did its appearance. Furthermore, the gasoline and kerosene distillates which it yielded were of a clear water-white color, entirely without treatment with acid or alkali, and were entirely free from the odor familiar in "cracked" petroleum distillates. The result of this experiment was quite too remarkable to be credited without further confirmation, and I at once filled the vessel with some of the same oil that I had used before, and again heated to about the same temperature that I had previously used, and for the same period of time. Upon opening the vessel and removing the contents I found, not the material resembling crude oil that I had obtained before, but apparently only the same oil that I had put in, somewhat darkened in color, but nevertheless far different in appearance from the material obtained in the previous experiment. Evidently some condition existed in the first experiment that had not existed in the second test, and here began a series of tests in which I sought by the change of one variable after another to arrive at the identical conditions which must have existed in the first experiment. Only the fact that the bottle of heavy oil used in the first test was still in its place,

Jan 1, 1915

By D. L. Murphy

As the world's demand for iron ore increases and available sources are depleted, increasing attention will be centered on deposits in the Quebec and Labrador portions of the Labrador Trough. Improvements in the beneficiation of low grade iron ore stimulate exploration for deposits amenable to concentration. This study is centered on the Mt. Wright-Lake Carheil area, lying between Wabush Lake and Mt. Reed in Quebec. Described in detail are the general lithology, structural and economic geology, and mineralogy of the iron-formation. The iron ore province of Quebec and Baffin Island extends from the southern shore of Baffin Island southeasterly through the Labrador Trough to Matonipi Lake, approximately 185 miles northwest of Seven Islands. (See Fig. 1.) Future geologic field studies will very likely extend the limits of the province to include the ferruginous and associated rocks of the Lake Mistassini area. At present, only the deposits near Knob Lake and Lake Jeannine (Mt. Reed) have been brought into production although in the near future several other properties including those at Wabush Lake will commence operations. Within the next decade or so, as the world's demand for iron ore increases and available sources are depleted, this region will undoubtedly become a major mining district. Initial reports of iron-rich rocks in Labrador date back to the investigations undertaken by A. P. Low near the turn of the century. During the ensuing years the country was prospected chiefly for precious and nonferrous base metals because of its inaccessibility and the low tenor of the iron ore. In 1945 an evaluation of the direct shipping ores near Knob Lake indicated that sufficient reserves were present to justify the enormous capital expenditure required to bring the deposits into production. Initial open-pit mining began in 1954 following the construction of a townsite, a 360-mile long railway to Seven Islands, and an elaborate loading dock. Recent improvements in the beneficiation of low-grade iron ore have stimulated widespread exploration for deposits amenable to concentration, particularly along the southwest extension of the Trough. The Mt. Wright-Lake Carheil area, bounded by longitudes 66O45' and 67 30' west and latitudes 52 30' and 52 45' north, is a nearly rectangular tract of slightly less than 500 sq miles. It is in Saguenay County, 174 miles north-northwest of Seven Islands (see Fig. 1). Except for the periods of the spring breakup and the fall freeze up, the area is readily accessible by air.

Jan 1, 1962

By H. M. Beatty, T. L. Joseph, Gust Bitsianes

SUCCESSFUL blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blast- furnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO ? 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which C02 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature com- bustion of carbon above the tuyeres. Assuming that 1000 lb. of limestone is used per ton of pig iron, about 435 lb. of C02 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb. would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1942

By John B. Mertie

MONAZITE formerly was described as moribund, but, in the light of recent developments, it is no longer so. It is the common source of the rare earths and thorium, both of which are becoming progressively important in industrial and other applications. Moreover, by the action of foreign governments, the sources on which the United States has depended for its supply are now either restricted or cut off entirely. Monazite has thus become a scarce mineral and processors in this country are endeavoring to acquire it from all available sources. RARE EARTHS AND THORIUM The rare earths proper, as defined by spectroscopists, are the oxides of cerium, praseodymium, neodymium, prometheum, samarium, europium, gadolinium, terbium, dysprosium, holmium, erbium, thulium, ytterbium and lutecium, with atomic numbers ranging respectively from 58 to 71. Chemists include with the rare earths scandium, yttrium, and lanthanum, with atomic numbers respectively of 21, 39, and 57. Thorium, with an atomic number of 90, is analogous to lanthanum, in that it precedes a second group of elements, whose oxides constitute the "rare earths of higher order." These are protactinium, uranium, neptunium, plutonium, americium and curium, with atomic numbers ranging respectively from 91 to 96. The last four mentioned are artificially prepared elements that so far have not been detected in nature. The rare earths with odd atomic numbers, except europium and lutecium, have no natural isotopes; and the two exceptions have only two isotopic forms. Those with even atomic numbers have from 4 to 7 natural isotopes. Samarium148 is radioactive, disintegrating over a half- life of 1.4 X 10 11 years with the emission of alpha rays. Lutecium176 is weakly radioactive, disintegrating over a half-life of 2.4 X 1010 years, with the emission of beta and gamma rays. At least 64 radioactive isotopes of the rare earths proper have been artificially prepared. Thorium is a strongly radioactive element, with a half-life of 1.39 x 1O10 years, which disintegrates through a series of 14 isotopes of 10 elements. The two longest lived and most important of these are

Jan 1, 1949

By H. E. Nold

THE raw materials of the ceramic industry are mostly clays. This raw material is ground, water is added and the mixture pugged into a moist, plastic, rather stiff mass. From this mass the desired units of manufacture are made (bricks, hollow building tile, sewer pipe, etc.). These units are dried; then placed in kilns and heated until the desired degree of vitrification is obtained.1 For firing ceramic ware, two distinct types of kilns are used; namely, periodic and continuous tunnel. PERIODIC KILNS Periodic kilns are those ordinarily seen in a brick plant. They are either round or rectangular. The raw, dried, formed ware is piled or set in the kilns to depths frequently exceeding 10 ft. The kiln is heated until the ware is matured, then gradually cooled sufficiently to allow men to remove the ware; then the cycle is repeated. The time duration of the cycle may be more than two weeks. In order that heat can be distributed uniformly throughout the pile or setting, the units are placed so as to leave open spaces or flues through-out the pile for the passage of the hot gases. Each kiln is provided with a number of fireboxes (usually 10 or 12) spaced equally in the outside wall. The fireboxes may be equipped with flat or inclined grate bars or they may have no grates at all (dead bottom). Down-draft kilns are most used. In these the hot gaseous products of combustion from the fireboxes are deflected upward by bag walls just inside the fire zone. From the top of the kiln the gases are drawn down through the setting, off through holes in the kiln bottom, and conducted to a stack or stacks. In up-draft kilns the fireboxes are usually set somewhat lower. The hot gases are drawn inward and upward through the ware and pass off from the top. Up-draft kilns find their greatest use in the firing of common brick. In either case the problem is to maintain, as nearly as possible,

Jan 1, 1933

By P. Hadzeriga

There are two places in the world where potash, trade name for potassium chloride, is economically recovered from naturally occurring brines by solar evaporation. One is at the Dead Sea and the other at Wendover, Utah. American Potash and Chemical at Trona, Calif. recovers potash from natural brines, but uses fuel to accomplish evaporation. Solar evaporation is always desirable, because of low costs, however artificial evaporation may be economical if a group of very valuable salts are recovered. This is the case for the American Potash operations at Trona. Solar evaporation is limited by low working temperatures, which in most areas of the world is between 18 and 45°C. In many cases the average working temperature is about 25°C. However, solar evaporation will have to accommodate itself to the highs and lows of each 24 hour period, and to the different average temperatures during the months of the year. Therefore, solar evaporation, although more economical than artificial evaporation, has a tem- perature limit which greatly reduces the chances of its application. The feasibility of solar evaporation as a means of recovery of values from a particular brine, may be evaluated by the use of phase diagrams showing the several components present. This paper is restricted to the five component system: C1-, SO4=, Na+, K+, Mg++, and H2O, which correspond to brines found at Wendover, Utah, the Great Salt Lake, and sea water bitterns. THE BONNEVILLE OPERATION AT WENDOVER, UTAH For more than 25 years Bonneville, Ltd., now a division of Standard Magnesium and Chemical Co. (recently acquired by Kaiser Aluminum and Chemical Corp.), has been recovering potassium chloride from the brines found in the desert area just east of Wendover, Utah. Solar evaporation of the brines is possible as a consequence of relatively low precipitations (year average: 4.8 in.), and of dry and hot summer months. The brine, collected by a series of approximately 67 mi. of ditches crossing the desert, is fed into solar evaporation ponds. Evaporation which takes place from around the middle of May to about the end of September, permits the crystallization of approximately 90% of the originally present NaCl on what is called the "General Pond Area". Further evaporation,

Jan 1, 1964

By R. Webeler

In order to study the role of work hardening in the fatigue process, use was made of the great sensitivty of the resistivity of AuCu to cold work. A change of the resistivity of AuCu of the order of 1 to 2 pct at the temperature of liquid nitrogen was found to occur as a consequence of severe fatigue. ACCORDING to Orowan's theory,' the process of fatigue In metals 1s associated with the production of a number of small regions which have undergone strain hardening. This phenomenon is supposed to occilr even if the stress applied during fatiguing is always smaller than the yield stress. In an attempt to verity the existence of such regions, Welber and Webeler' undertook to detect the stored energy associated with severe fatigue in copper. Previous experiments" had shown that the energy stored in a sample of copper which has been cold worked by torsion is released in the temperature range between 150" and 250°C when the sample is heated from room temperature and that no more energy is released (or absorbed) between 250" and 450°C. In particular the stored energy amounted to 0.41 cal per g for a case in which the mechanical energy expended in twisting the sample was 11.9 cal per g. In the case of fatigued copper, however, no release of stored energy could be detected between 150" and 250°C, so that the experimental error of &0.02 cal per g represents an upper limit for the amount of energy stored in strain hardening., It seemed desirable to attack the problem in a new fashion. For this purpose, it was decided to make use of the fact that, if an alloy capable of undergoing the order-disorder transition is ordered and then cold worked, the resistivity, p, increases very greatly above the value for the ordered state even if the deformation is very small. Some insight into the nature of the fatigue process may be obtained then by measuring the resistivity of an ordered sample before and after subjecting it to fatigue. For reasons which will become apparent from the following remarks, considerably more can be learned by carrying out the resistivity measurements at two different temperatures. In the case of a material containing impurities, vacancies, dislocations, or other imperfections of essentially atomic dimensions, the resistivity, p, according to Matthiessen's rule, can be represented as a sum of two terms p = p, + p, where p, is the (temperature dependent) resistivity of the pure metal, and p, is the temperature independent contribution of the imperfections. Briefly, the physical basis for this rule is the following: The main contribution of the impurities in question to the resistivity results from the fact that they interrupt the periodicity of the lattice and thus scatter the conduction electrons with a probability which is almost independent of temperature. In order that this be the case, it is necessary that the' extension of the impurities be small enough—roughly less than one electron mean free path—so that their main effect on the resistivity occurs for the foregoing reason. If an alloy like AuCu is partly or completely disordered by quenching from an appropriate temperature, Matthiessen's rule also applies to a very good approximation* with p, representing in this case the resistivity po of the ordered sample and p, the additional (temperature independent) resistivity due to the disorder. In general, the disorder can be represented in terms of atoms which are displaced from their "proper" positions in the superlattice and which thus qualitatively represent the imperfections in the superlattice responsible for the term p,. Since the misplaced atoms are distributed at random throughout the super-lattice, their contribution to the resistivity still can be considered in terms of the scattering of conduction electrons by lattice defects. The situation is somewhat more complex in the case of an alloy disordered by cold work because the process of disordering here does not involve a random redistribution of the atoms; however, Matthiessen's rule also holds in this case. Whenever Matthiessen's rule does apply, the values of the quantity /3 = (p? — /(T, — T,), where p, and p, are the values of the resistivity at two fixed temperatures, T, and T,, respectively, is constant (independent of p,) for a given alloy or metal. In particular, if a sample of AuCu is subjected to ordinary cold work, the value of /3 remains equal to Po, the value for the ordered material. According to Orowan's theory,' as remarked before, a fatigued sample contains a large number of isolated severely cold-worked regions, which make up only a small proportion of the metal. Thus, if a sample of AuCu initially in the ordered state is fatigued, more or less disordered regions will be produced within the ordered material. If these regions are small enough so that Matthiessen's rule applies, then it follows from the previous discussion that /3 again will remain equal to Po. If the effect of fatigue is to produce cold-worked regions which are macroscopic—of the order of at least several electron mean free paths—the effective resistivity, p, has to be computed by use of the ordinary laws of large-scale electrodynamics. For the sake of simplicity, it will be assumed here that the cold-worked regions are completely disordered and have a resistivity, p,. For a given proportion A of disordered regions the effective resistivity, p, for the current in a given direction depends on the geometrical configuration of these regions. In any case, the value of p for such

Jan 1, 1956

By D. V. Fites

Criteria for deciding when rock should be ripped and what ripping equipment and techniques should be used in given situations are discussed in this article. The relation between ripper performance and seismic wave velocities in various types of rock is also discussed. The ripper is not a new tool. In fact, it dates back as far as the Roman Empire. The Roman's ripper-mounted on wheels and shaped something like a plow — was pulled by oxen and used to loosen the earth for the shovelers and basket carriers building the Appian Way. There are records of rippers being used in this country in railroad construction between 1860 and 1880. However, the ripper as we know it today did not appear until about 1930. Tractor-drawn models were in use in 1931 on the Hoover Dam project. At that time they weighed about 7500 lb and were pulled by tractors with about 75 flywheel hp and up to 30,000 Ib total weight. The chief shortcomings of trailed

Jan 1, 1969

By Rex B. McLellan, M. L. Rudee, T. Ishibachi

A modelfor dilute quasi-regular interstitial solid solutions is proposed in which the solute atoms can occupy both the octahedral and tetrahedral interstices in the bee solvent lattice. The distribution function, according to which the solute atoms are apportioned between the two kinds of sites, is calculated. The partial thermodynamic functions of the solution are calculated from the distribution function. It is shown that such a solution model can explain the deviation from linearity of the Arrhenius plot of the temperature variation of the diffusivity of carbon through a iron. The published difiusivity data is analyzed to obtain numerical values for the distribution function. Finally it is shown from the numerical values of the distribution function that the possibility of dual-site occupancy will have a negligible effect on the solution thermodynamics for this system. DeSPITE the large amount of experimental data available on the thermodynamics and diffusion kinetics of dilute solid solutions of carbon in a iron, many of the elementary properties of these solutions are not understood due to real or apparent discrepancies in the experimental data. Basically there is a lack of agreement between the solubility and diffusion data obtained by anelastic damping techniques and by bulk chemical thermodynamic methods. SPecifically the heat of solution of cementite in ferrite estimated from thermodynamic measurement1, 2 is about twice as high as that determined from anelastic damping measurements.3 Furthermore the diffusion coefficient D of carbon in a iron in the range -40" to about 150°C (covering about ten orders of magnitude) determined from anelastic damping techniques is such that an Arrhenius plot of In D vs 1/T is linear. However in the range of about 300o to 850°C where mass flow measurements of D have been made (covering about four orders of magnitude), although the data merges with the low-temperature data, the Arrhenius plot departs from linearity. The object of this paper is to present a more refined model of dilute ferrite solutions in which the solute atoms can occupy two kinds of interstitial sites. The experimental data is analyzed in the light of this model and it is believed that thereby some of the anomalies can be resolved. snoek4 explained the room-temperature internal-friction peak (usually referred to as the Snoek peak) in iron as the stress-induced ordering of interstitial carbon and nitrogen atoms occupying the octahedral (0, 0, 1/2) interstices in the bee lattice. From the consideration of a hard-sphere lattice model the (0, 1/4, 1/4) tetrahedral interstices are larger than the octahedrons but their symmetry would not produce the strain dipole necessary to give rise to the Snoek peak. Thus the presence of the Snoek peak is direct evidence that the octahedrons are occupied. Since the publication of Snoek's explanation, most workers have assumed that all of the carbon and nitrogen in the a solid solution was located in the octahedral sites. This assumption of universal octahedral occupancy has been implicit in the theory of wert5 for interstitial

Jan 1, 1965

By C. M. Moncrief, B C. Craft

A bentonite-clay drilling mud when treated with tetrasodium pyroarsenate underwent substantially the same reduction in viscosity and water loss as when treated with the complex phosphates. The complex arsenate showed a slightly higher reversion after heating; the other arsenates showed poor viscosity-reducing properties. Introduction During the past 10 years the chemical control of drilling mud has become of major importance in affecting the successful drilling and working over of wells. The desired properties of drilling mud have been well established, and in obtaining these characteristics there has developed a large market for viscosity-reducing chemicals. Viscosity reduction produced by humic acid, tannic acid, sodium silicate, sodium tannate, Calgon, and the complex phosphates has been described by Loomis, Ford, and Fidiam.l The effects Of treatment with complex phosphates and ammonium PolyPhosPhates on the rheological properties of muds were investigated by Fancher2 and the alkali vanadates have been described by Williams.3 Laboratory Investigations It is the purpose of this paper to point out the effects of arsenates in controlling the viscosity and gelling characteristics of a drilling mud. Viscosities and gel strengths were measured at room temperatures with a Stormer viscosimeter calibrated in centipoises and operated at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester at a pressure of I00 lb. per sq. in. for 30 min. The hydrogen-ion concentration was measured with a glass electrode. The bentonite-clay suspensions were prepared in the laboratory and allowed to age several days before testing. Members of the Arsenic Group in the periodic Table include arsenic, antimony and bismuth, but this investigation was limited to arsenic. Phosphorus also occurs in Group V of the Periodic system and phosphorus and arsenic form many closely related compounds such as pH3 and AsH3, P2O5 and As2O5, H3PO4 and H3AS04 Samples of tetrasodium pyroarsenate were prepared by fusing c.p. disodium arsenate (Na2HA5O4.7H2O). According to Friend,' this re-forms the ortho-arsenate on dissolution in water. Sodium trihydrodiorthoarsenate was prepared as described by Mellor,5 from arsenic pen-toxide as follows: As2O5 + 3H20 -> 2H3AsO4 2H3AS04 + 3NaOH Na3H3(AsO4)2 .3H20 Sodium dihydrogen orthoarsenateWaHz-As04) was obtained by fusing together equivalent quantities of arsenious Oxide and sodium nitrate, dissolving the residue in water and allowing it to crystallize.

Jan 1, 1946

By C. M. Moncrief

A bentonite-clay drilling mud when treated with tetrasodium pyroarsenate underwent substantially the same reduction in viscosity and water loss as when treated with the complex phosphates. The complex arsenate showed a slightly higher reversion after heating; the other arsenates showed poor viscosity-reducing properties. Introduction During the past 10 years the chemical control of drilling mud has become of major importance in affecting the successful drilling and working over of wells. The desired properties of drilling mud have been well established, and in obtaining these characteristics there has developed a large market for viscosity-reducing chemicals. Viscosity reduction produced by humic acid, tannic acid, sodium silicate, sodium tannate, Calgon, and the complex phosphates has been described by Loomis, Ford, and Fidiam.l The effects Of treatment with complex phosphates and ammonium PolyPhosPhates on the rheological properties of muds were investigated by Fancher2 and the alkali vanadates have been described by Williams.3 Laboratory Investigations It is the purpose of this paper to point out the effects of arsenates in controlling the viscosity and gelling characteristics of a drilling mud. Viscosities and gel strengths were measured at room temperatures with a Stormer viscosimeter calibrated in centipoises and operated at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester at a pressure of I00 lb. per sq. in. for 30 min. The hydrogen-ion concentration was measured with a glass electrode. The bentonite-clay suspensions were prepared in the laboratory and allowed to age several days before testing. Members of the Arsenic Group in the periodic Table include arsenic, antimony and bismuth, but this investigation was limited to arsenic. Phosphorus also occurs in Group V of the Periodic system and phosphorus and arsenic form many closely related compounds such as pH3 and AsH3, P2O5 and As2O5, H3PO4 and H3AS04 Samples of tetrasodium pyroarsenate were prepared by fusing c.p. disodium arsenate (Na2HA5O4.7H2O). According to Friend,' this re-forms the ortho-arsenate on dissolution in water. Sodium trihydrodiorthoarsenate was prepared as described by Mellor,5 from arsenic pen-toxide as follows: As2O5 + 3H20 -> 2H3AsO4 2H3AS04 + 3NaOH Na3H3(AsO4)2 .3H20 Sodium dihydrogen orthoarsenateWaHz-As04) was obtained by fusing together equivalent quantities of arsenious Oxide and sodium nitrate, dissolving the residue in water and allowing it to crystallize.

Jan 1, 1946

By M. T. Simnad, C. E. Birchenall, M. H. Davies

THE marker movements observed by Davies, Simnad, and Birchenall during the growth of magnetite on wustite have been misinterpreted. It is the purpose of this note to correct the original interpretation. In that investigation wustite specimens were prepared by oxidizing pure iron disks in water vapor until the iron was consumed. Argon was used as a carrier gas for the water vapor and on the complete conversion of the metal to its oxides ('FeO' plus a small amount (10 pct) of surface Fe3O) the water supply was bypassed and the specimens were annealed in argon alone in order to equilibrate the wustite with the overlying magnetite. After cooling, the magnetite was ground off, a crude magnetic test being employed to determine its complete removal. Radioactive silver streaks were then applied to the surface and the specimen was oxidized completely in water vapor to prevent hematite formation. After complete oxidation the markers were found to enclose about 80 pct of the magnetite with the other 20 pct lying outside the markers. This observation was interpreted to mean that oxygen transport was four times as great as iron transport during the growth of the magnetite. The conclusion would have been correct if, as in the case of wustite growing on iron, all the iron had started from one side of the marker and all the oxygen from the other side initially. Actually a material balance is required. For simplicity, take wustite to be exactly FeO, and magnetite to be Fe3O,. Then at the start of the reaction 3 FeO + O -> Fe,O., All of the iron and three-fourths of the oxygen of the final product will be within the marker inter- faces. The other fourth of the oxygen is in the gas phase outside the marker. From the experimentally determined final position of the markers simple calculation shows that one-fifth of the total iron has crossed the marker interface, while one-twentieth of the total oxygen has crossed in the reverse direction. The simplified result favors iron transport in the ratio four to one. However wiistite is not stoichiometric FeO. At 900°C, the temperature of the measurement, the composition is about FeO When the material balance for the same experimental result is repeated, assuming the product will be 1 mol of Fe3O4, it is found that 0.6 gram atoms of iron and 0.19 gram atoms of oxygen must have passed the marker in the same direction. (This is readily apparent from the reaction to form 1 mol of Fe3O4 SFeO The total oxygen supplied from the atmosphere is 0.61 gram atoms, but the iron which passes the marker interface, i.e., 0.6 gram atoms, requires 0.8 gram atoms of oxygen to convert it to Fe,O,.) If all the transport during magnetite growth is due to iron ion diffusion, then the marker would enclose about 85 pct of the final magnetite and the original measurement is in error by about 5 pct. This error is probably less than the uncertainty in locating the markers by autoradiography. The possibility also exists that the starting wustite was not quite saturated with oxygen and underwent further enrichment with consequent envelopment of the marker before magnetite caught up with the marker interface. In any case it appears that these measurements actually favor iron ion diffusion in magnetite overwhelmingly as the factor controlling its growth, although further experimental measurements are needed to eliminate the error in material balance described. Such studies are planned.

Jan 1, 1954

The Tuscarora mining district, which has been highly productive of gold and silver ores in past years, is situated about 50 miles north- west of Elko, Nevada. The town of Tuscarora lies at an altitude of about 6,000 ft on the west side of the Independence Valley. Precipitation, particularly the winter snowfall, is considerably greater than in many other parts of Nevada, and temperatures are lower. From Tuscarora can be seen-across Independence Valley in the mountains to the east, a distance of about 12 miles, the Freeport Minerals Jerritt Canyon mine, which seems to be-destined to become one of the great gold mines in the western hemisphere. Tuscarora, a gold and silver camp, was active from the early 1870s to 1903 and produced about $10 million in those 30 years. Ten major mines and several smaller ones were operated in an area of about 1.45 square kilometers (one-half squaremile). The deepest shafts were only 230 m (750 ft) but most of the ore came from about the 105 m (350 ft) levels. Mineralization above the water table, at about 30 m (100 ft), was mostly native silver and cerargerite with free gold. Below the water table the ore was rich in sulfides including argentite, stephanite, proustite, pyrargyrite, enargite, arsenopyrite, bornite, chalcopyrite, pyrite, sphalerite and galena. A number of the properties contain sizeable dumps of what was con- sidered waste rock when it was mined. These dumps aggregate over 408,000 mt (450,000 st) with one dump, the Navajo, containing over one-third of the total. A few grab samples taken in the summer of 1978 from some of the dumps indicated interesting silver values with minor gold content. AgAu Exploration Ltd., was organized to explore and develop these dumps into a heap leaching operation. In the fall of 1978 a campaign was started to lease, with front money payments on a royalty basis, three groups of claims on which were located a few hundred thousand tons of dumps. In September and October of 1978, a systematic program of sampling was started on the Navajo dump which was most favorably situated in that it was near to an area which would furnish good sites for heap leaching pads. At the time it was fully recognized that sampling of dumps was a most difficult problem. Because of the topography on which they were situated and the manner in which they were formed, each dump required its own special sampling technique.

Jan 1, 1981

PAUL D. MERICA,* Washington, D. C. (written discussion t).-This paper is a discussion of some of the results of a recent investigation1 of Prof. Zay Jeffries, and of his interpretation and generalizations from these results. This work I have followed with great interest and with appreciation of its value in clarifying our views on the nature of deformation in metals and its relation to structure. It is only by such close study of the relation of structure to mechanical properties that we shall ever be able to describe the latter in terms of their ultimate elements, and thus explain what are still mysteries in the mechanical behavior of metals; experiment and thought along these lines are in my opinion of the utmost value. If I, therefore, here record some of the difficulties I have experienced in understanding some of the generalizations of Prof. Jeffries, it is only in order that perhaps from the discussion may emerge a clearer and more consistent statement of hypothesis or theory in explanation of the facts discovered by him.

Jan 11, 1918

By Sylvan Cromer

The need for a clear understanding of the physical nature of the flow of gas-liquid mixtures in vertical pipes is ever becoming more apparent. This type of flow is encountered when gas and oil are produced from a well; when water is removed from gas wells with siphon lines and when liquids are elevated by means of air or gas lift. Although a number of investigator1-7 have published data on the flow of gas-liquid mixtures, in only a few cases has the experimental setup been devised to permit visual study. In the fields of heat transmission, such as the boiling of liquids and the study of the critical phenomena of the hydrocarbons, researchers have been able to throw additional light on heretofore unexplainable happenings through actual observation in glass apparatus. This investigation was therefore undertaken in order to obtain qualitative as well as quantitative results for air-water flow. Experimental Apparatus and Procedure The flow column used in these tests was made of standard 2-in. pipe and was approximately 98 ft. in height. Pyrex observation sections 2 ft. long having the same internal diameter as the wrought-iron pipe were placed at 14-ft. intervals in the column. The bottom of the tube was cut off square and terminated in the mixing chamber. No perforated nipple or footpiece of any kind was used. To the top of the column was fastened a semicircular return bend having a 4-ft. radius. The flow column was supported by a standard cable-tool drilling derrick (Fig. 1) into which were built observation platforms at each Pyrex section.

Jan 1, 1940

By Sylvan Cromer

The need for a clear understanding of the physical nature of the flow of gas-liquid mixtures in vertical pipes is ever becoming more apparent. This type of flow is encountered when gas and oil are produced from a well; when water is removed from gas wells with siphon lines and when liquids are elevated by means of air or gas lift. Although a number of investigator1-7 have published data on the flow of gas-liquid mixtures, in only a few cases has the experimental setup been devised to permit visual study. In the fields of heat transmission, such as the boiling of liquids and the study of the critical phenomena of the hydrocarbons, researchers have been able to throw additional light on heretofore unexplainable happenings through actual observation in glass apparatus. This investigation was therefore undertaken in order to obtain qualitative as well as quantitative results for air-water flow. Experimental Apparatus and Procedure The flow column used in these tests was made of standard 2-in. pipe and was approximately 98 ft. in height. Pyrex observation sections 2 ft. long having the same internal diameter as the wrought-iron pipe were placed at 14-ft. intervals in the column. The bottom of the tube was cut off square and terminated in the mixing chamber. No perforated nipple or footpiece of any kind was used. To the top of the column was fastened a semicircular return bend having a 4-ft. radius. The flow column was supported by a standard cable-tool drilling derrick (Fig. 1) into which were built observation platforms at each Pyrex section.

Jan 1, 1940

No greater opportunity for public service has ever been presented to the engineers of the United States, as a class, than the campaign to make thrift a permanent American habit, conducted through the Savings Division off the Treasury Department. The engineer owes a duty to his community, to his country, by reason of the very fact that he is an engineer. By reason of his position and influence, his education and experience, he owes to his country the duty of public service. The public understands that the opportunities of the engineer have allowed him to equip himself to handle logically and properly questions affecting the public. He has been trained to maintain a constructive viewpoint. His work is constructive and he builds for the future. The qualities that the public deems necessary for public service have been bred in him. The time has gone by when the professional man can perform his whole duty to himself and his community by shrouding himself and his calling in mystery and locking himself away from the public in office or laboratory. The duty of public service is calling for every man whose training has fitted him to perform that service. The engineers of the country have demonstrated their capacity and their willingness for public service. Throughout the war period they, have been found in every branch of governmental and. civilian activity which could contribute to national success, doing their share to promote national efficiency. Their duties are not over.

Jan 7, 1919